Nissan Versa (2024 year). Manual in english

The Automatic Emergency Braking (AEB)
with Pedestrian Detection system is auto-
matically enabled when the vehicle is started.

To turn the system off, push the Automatic
Emergency Braking (AEB) with Pedestrian
Detection OFF switch (if so equipped). The
light will go off, and the AEB with Pedestrian
Detection system warning light will illumi-
nate in the meter. Pushing the switch will
also turn off the Rear Automatic Braking
(RAB) system.

For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian
Detection” (P. 5-83).

The vehicle should be driven with the VDC
system on for most driving conditions.

If the vehicle is stuck in mud or snow, the
VDC system reduces the engine output to
reduce wheel spin. The engine speed will
be reduced even if the accelerator is de-
pressed to the floor. If maximum engine
power is needed to free a stuck vehicle,
turn the VDC system off.

To turn off the VDC system, push the VDC
OFF switch. The

indicator light and the

Automatic Emergency Braking (AEB) with
Pedestrian Detection system warning light
will come on and the Rear Automatic Brak-
ing (RAB) system will turn off.

Push the VDC OFF switch again or restart
the engine to turn on the system. For addi-
tional information, see “Vehicle Dynamic
Control (VDC) system” (P. 5-119) and “Auto-
matic Emergency Braking (AEB) with Pe-
destrian Detection” (P. 5-83).

LIC4314

LIC4315

AUTOMATIC EMERGENCY BRAKING
(AEB) WITH PEDESTRIAN DETECTION
OFF SWITCH (if so equipped)

VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH (if so equipped)

2-54

Instruments and controls

WARNING

The Rear Sonar System is a conve-
nience but it is not a substitute for
proper backing. Always turn and check
that it is safe to do so before backing
up. Always back up slowly.

The RSS (if so equipped) is active when the
ignition switch is placed in the ON position
and the shift lever is in R (Reverse). The
indicator light on the switch will turn on.

When sensors detect obstacles within 6 ft
(1.8 m) of the rear bumper, a beeping tone is
emitted.

The RSS can be disabled by pushing the
OFF switch. When the system is disabled,
the indicator light on the switch will turn off.

The system will automatically reset the
next time the ignition switch is placed in
the ON position.

For additional information, see Rear Sonar
System (RSS) (P. 5-122).

EMERGENCY SUPPORT

NissanConnect® Services provide various
services to support dealing with emergen-
cies of the subscribed vehicle and the
driver.

For example, in case of an illness or serious
injury, you can seek support by pressing the
in-vehicle Emergency Call (SOS) button and
connecting to the NissanConnect® Services
Response

Center.

The

NissanConnect®

Services Response Center can specify the
location of the vehicle via GPS, and the infor-
mation will be sent to the police or other
agencies as needed.

For information about other NissanConnect®
Services emergency support related ser-
vices, contact the NissanConnect® Cus-
tomer Support line at 1–855–426–6628 or
refer to the NissanConnect® Services web-
site www.nissanusa.com/connect (for U.S.)
or www.nissan.ca/nissanconnect (English) /
www.nissan.ca/nissanconnect/fr (French)
(for Canada).

LIC5040

REAR SONAR SYSTEM (RSS) OFF
SWITCH (if so equipped)

EMERGENCY CALL (SOS) BUTTON
(if so equipped)

Instruments and controls

2-55

WARNING

•

Please note that the Automatic Colli-
sion Notification service and Emer-
gency Call function cannot be used in
the following conditions:

–

Emergency functions and services
will not be available without a paid
subscription to NissanConnect® Ser-
vices.

–

The NissanConnect® Services net-
work system is disabled.

–

The vehicle moves outside the ser-
vice area where the TCU (Telematics
Control Unit) is connected to the
system.

–

The vehicle is outside the area
where the cellular network service
is receivable.

–

The vehicle is in a location with poor
signal reception such as tunnels,
underground parking garages, be-
hind buildings or in mountainous
areas.

–

The line is busy.

–

The TCU (Telematics Control Unit)
or other systems of your vehicle
are not working properly.

–

It may not be possible to make
an emergency call depending on
the severity of a collision and/or
emergency.

•

Park the vehicle in a safe location and
set the parking brake before operat-
ing the Emergency Call (SOS) button.

•

Only use this service in case of an
emergency. There may be a penalty
for inappropriate use of the service.

•

Radio waves could adversely affect
electric medical equipment. Indi-
viduals who use a pacemaker should
contact the device manufacturer re-
garding any possible effects before
using the system.

•

The TCU (Telematics Control Unit) an-
tenna is installed inside the upper
central part of the instrument panel.
An occupant should not get any
closer to the antenna than specified
by the pacemaker manufacturer. The
radio waves from the TCU antenna
may adversely affect the operation
of the pacemaker while using the
NissanConnect® Services.

2-56

Instruments and controls

Making an emergency call

The Emergency Call (SOS) button is located
near the map light.

1. Push the cover

to expose the Emer-

gency Call (SOS) button

2. Press the Emergency Call (SOS) button

to make an emergency call.

3. When the line is connected, speak to the

Response Specialist.

If you want to cancel the emergency call,
press and hold the Emergency Call (SOS)
button for a few seconds.

NOTE:

•

After the Emergency Call (SOS) button
is pressed, it may take some time until
the system initiates connection, de-
pending on the technical environment
and whether the TCU (Telematics Con-
trol Unit) is being used by the other
services.

•

An indicator light on the Emergency
call (SOS) button shows the readiness
of the emergency support system. If
the indicator light is not illuminated,
pressing the Emergency Call (SOS)
button does not connect your vehicle
to the Response Specialist. The indi-
cator light blinks while connected to
the NissanConnect® Services Response
Center.

•

Even when the indicator light is illumi-
nated, connection to the NissanConnect®
Services Response Center may not be
possible. If this occurs in an emergency
situation, contact the authorities by
other means.

•

To avoid disconnecting the line, keep
the engine running during an emer-
gency call, if it is safe to do so.

LIC5075

Instruments and controls

2-57

1. Type-A USB

2. Type-C USB

There are USB/iPod® charging ports lo-
cated on top of the center console, on the
back of the center console or inside the
console box. These ports will charge com-
patible devices.

NOTE:
• The USB/iPod® charging ports will not

operate with the display screen. Only
the USB connection port located on the
instrument panel, below the tempera-
ture controls, will operate USB/iPod®
devices through the audio system.

• For best results, it is recommended to

use the manufacturer cables, which
are sold separately. A USB Type-A to
USB Type-C adapter (or vice versa) can
also be purchased separately; how-
ever, results may vary.

LIC5034

Top of center console (if so equipped)

LIC5088

Back of center console (if so equipped)

LIC5123

Inside console box (if so equipped)

USB/iPod® CHARGING PORTS

2-58

Instruments and controls

The wireless charger is located on the front
of the center console. Lay the smartphone
on the pad of the wireless charger. Charg-
ing will start automatically. The smart-
phone will be charged continuously while
the ignition switch is in the ON position.

NOTE:

The wireless charger requires the vehicle
doors to be closed before charging will
start. If the doors are opened, the charg-
ing function will not operate.

WARNING

•

Never put metallic materials between
the wireless charger and a smart-
phone.

•

Those who use a pacemaker or other
medical equipment should contact
the electric medical equipment manu-
facturer for the possible influences
before use.

•

Never put cloth over the smartphone
during charging process.

•

Never charge a smartphone when it
is wet.

•

Never put metallic materials or small
goods such as a cigarette lighter,
Intelligent Key or memory drive.

CAUTION

•

Do not put an RFID/NFC/credit card
between the wireless charger and a
smartphone. This could cause data
corruption in the card.

•

Do not use the wireless charger with
dust accumulated or dirt on the pad.

•

Do not hit the surface of the wireless
charger.

•

Do not spill liquid (water, drinks, etc.)
on the charging pad.

•

Do not use grease, oil or alcohol for
cleaning charging pad.

WIRELESS CHARGER INDICATOR

The indicator ( 1 ) will illuminate in orange
when the charging process is started.

When the charging has completed, the in-
dicator illuminates in green.

If a malfunction occurs or the charging
process has stopped, the indicator will
blink in orange for 8 seconds then turn off.

WIRELESS CHARGER OPERATION

To use the wireless charger, it is necessary
to seat the smartphone well within the
charging pad. To maximize charging per-
formance, ensure the smartphone is fully
seated on the center of the charging pad
over the "Qi" logo

. Because the location

of the power receiver may vary depending
on the smartphone, you will need to try and
find the area that suits your smartphone.

Because some smartphone cases or ac-
cessories may adversely affect charging,
remove them before wireless charging.
Turn off the vibration function of the smart-
phone before wireless charging.

LIC5100

1. Indicator

2. Charging pad

WIRELESS CHARGER (if so equipped)

Instruments and controls

2-59

NOTE:

•

Only a Qi compatible smartphone can
be used.

•

The smartphone may be warmed dur-
ing charging process and the charging
may stop by the protection function of
the wireless charger. This is not a mal-
function. If this occurs, restart charging
after the smartphone has cooled down.
The indicator will blink in orange then
turn off.

•

The wireless charging process may be
stopped by the status of the smart-
phone (battery temperature, etc.).

•

If a radio noise interference occurs dur-
ing charging process, put the smart-
phone onto the center (“Qi” logo) posi-
tion of the wireless charger.

•

The wireless charging process will stop
during process of searching the Intelli-
gent Key.

•

The wireless charging process will not
be started when a USB (Universal Serial
Bus) cable is connected to the smart-
phone. The indicator may illuminate in
orange or blink if the smartphone is
put on the wireless charger with a USB
cable connected. However, charging is
not performed.

•

Depending on the type of the smart-
phone, the indicator may remain illu-
minated in orange even when the
charging process has been completed.

This device complies with part 15 of the
FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
RF Radiation Exposure Statement: This
equipment complies with FCC RF Radia-
tion exposure limits set forth for an un-
controlled environment.
This device and its antenna must not be
co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and
operated with a minimum distance of
15cm between the radiator and your body.

ISED Compliance Statement
This device complies with RSS-Gen of IC
Rules
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Changes or modifications made to this de-
vice, not expressly approved by LG Vehicle
Components Company, will void the user’s
authority to operate the equipment.
ISED RF Radiation Exposure Statement:
This equipment complies with ISED RF
Radiation exposure limits set forth for an
uncontrolled environment. This device
and its antenna must not be co-located
or operating in conjunction with any other
antenna or transmitter. This equipment
should be installed to operate with a mini-
mum distance of 15 cm between the radia-
tor and the end-user’s body and arms.

2-60

Instruments and controls

The Rear Door Alert system functions un-
der certain conditions to indicate there
may be an object or passenger in the rear
seat(s). Check the seat(s) before exiting the
vehicle.

The Rear Door Alert system is initially dis-
abled. The driver can enable the system
using the vehicle information display. For
additional information, see “Vehicle infor-
mation display warnings and indicators”
(P. 2-36).

When the system is enabled:
• The system is activated when a rear door

is opened and closed within 10 minutes of
the vehicle being driven. When the driver
door is closed and the system is acti-
vated, a visual message appears in the
vehicle information display. For additional
information, see “Rear Door Alert is acti-
vated” (P. 2-38).

• If a rear door is opened and closed but

the vehicle is not driven within approxi-
mately 10 minutes, the system will not be
activated. A rear door must be opened
and closed and the car driven within 10
minutes for the system to activate.

When the Rear Door Alert system is activated:
• When the driver puts the vehicle in the P

(Park) position, a notification message
appears in the vehicle information dis-
play with the options to “Dismiss Mes-
sage” or “Disable Alert” if desired.

– Select “Disable Alert” to temporarily

disable for that stop.

– No selection or ‘Dismiss Message” will

keep the alert enabled for that stop.

• If the alert is enabled when a driver exits

the vehicle, a message will appear in the
vehicle information display that states
“Check Back Seat For All Articles.”

If “Horn & Alert” setting is selected:

–– An audible horn sound will occur after

a short time unless a rear door is
opened and closed within a short time
to deactivate the alert.

–– If the doors are locked before the alert

is deactivated by opening a rear door,
the horn will sound.

–– If the trunk is opened before a rear door

is opened, the horn will be delayed until
after the trunk is closed.

NOTE:

If “Alert Only” setting is selected, the
message alert will still be shown in the
vehicle information display but the horn
will not sound.

WARNING

•

If the driver selects “Disable Alert”, no
audible alert will be provided regard-
less of rear door open/close status.

•

There may be times when there is an
object or passenger in the rear seat(s)
but the audible alert does not sound.
For example, if rear seat passengers
enter or exit the vehicle during a trip.

•

The system does not directly detect
objects or passengers in the rear
seat(s). Instead, it can detect when a
rear door is opened and closed, indi-
cating that there may be something
in the rear seat(s).

NOTE:

There may be times when the horn
sounds but there are no objects or pas-
sengers in the rear seat(s).

For additional information, see “Rear Door
Alert is activated” (P. 2-38).

REAR DOOR ALERT (if so equipped)

Instruments and controls

2-61

The power outlet is for powering electrical
accessories such as cellular telephones.
The outlet is rated at 12 volt, 120W (10A)
maximum.

CAUTION

•

The outlet and plug may be hot dur-
ing or immediately after use.

•

Only certain power outlets are de-
signed for use with a cigarette lighter
unit. Do not use any other power out-
let for an accessory lighter. It is rec-
ommended that you visit a NISSAN
dealer for additional information

•

Do not use with accessories that ex-
ceed a 12 volt, 120W (10A) power draw.

•

Do not use double adapters or more
than one electrical accessory.

•

Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.

•

Avoid using power outlets when the
air conditioner, headlights or rear
window defroster is on.

•

Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned off.

•

Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.

•

When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.

The extended storage switch is used when
the vehicle is in transit from the factory. It is
located in the fuse panel

which is on the

driver’s side left kick panel, near the floor,
on the inside of the panel. If any electrical
equipment does not operate, ensure the
extended storage switch is pushed fully in
place, as shown.

LIC5126

Instrument panel

LIC3581

POWER OUTLETS

EXTENDED STORAGE SWITCH

2-62

Instruments and controls

SEATBACK POCKET (if so equipped)

The seatback pocket is located on the
back of the passenger's seat. The pocket
can be used to store maps.

WARNING

To ensure proper operation of the driv-
er’s and/or front passenger’s NISSAN Ad-
vanced Air Bag System (if so equipped),
please observe the following items:

•

Do not allow a passenger in the rear
seat to push or pull on the seatback
pocket or head restraint/headrest.

•

Do not place heavy loads heavier
than 9.1 lbs. (4 kg) on the seatback,
head restraint/headrest or in the
seatback pocket.

STORAGE TRAYS (if so equipped)

WARNING

Do not place sharp objects in the trays
to help prevent injury in an accident or
sudden stop.

LIC0016

LIC5036

2-64

Instruments and controls

GLOVE BOX

Open the glove box by pulling the handle.

WARNING

Keep glove box lid closed while driving
to help prevent injury in an accident or
a sudden stop.

CONSOLE BOX (if so equipped)

To open the console box, pull on the lever

and raise the lid

To close, push the lid down until the lock
latches.

CUP HOLDERS

CAUTION

•

Avoid abrupt starting and braking
when the cup holder is being used
to prevent spilling the drink. If the
liquid is hot, it can scald you or your
passenger.

•

Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.

LIC3580

LIC5124

LIC5037

Center console without armrest

(if so equipped)

Instruments and controls

2-65

CAUTION

•

Do not use bottle holder for any other
objects that could be thrown about
in the vehicle and possibly injure
people during sudden braking or an
accident.

•

Do not use bottle holder for open liq-
uid containers.

LIC5125

Center console with armrest

(if so equipped)

LIC5462

Bottle holder — front

LIC5464

Bottle holder — rear

2-66

Instruments and controls

POWER WINDOWS

WARNING

•

Make sure that all passengers have
their hands, etc., inside the vehicle
while it is in motion and before clos-
ing the windows. Use the window
lock switch to prevent unexpected
use of the power windows.

•

To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not
leave children, people who require
the assistance of others or pets unat-
tended in your vehicle. Additionally,
the temperature inside a closed ve-
hicle on a warm day can quickly be-
come high enough to cause a signifi-
cant risk of injury or death to people
and pets.

The power windows operate when the ig-
nition switch is placed in the ON position or
for a period of time after the ignition switch
is placed in the OFF position. If the driver's
or passenger's door is opened during this
period of time, the power to the windows is
canceled.

Driver's side power window switch

The driver's side control panel is equipped
with switches to open or close all of the
windows.

To open a window, push the switch to the
detent and continue to hold down until the
desired window position is reached. To
close a window, pull the switch to the de-
tent and continue to hold up until the de-
sired window position is reached.

Locking passengers' windows

When the window lock switch is depressed,
only the driver's side window can be
opened or closed. Push it again to cancel
the window lock function.

LIC3208

1. Window lock switch

2. Power door lock switch

3. Front passenger side switch

4. Right rear passenger side switch

5. Left rear passenger side switch

6. Driver’s side automatic switch

WINDOWS

Instruments and controls

2-67

Front passenger's power window
switch

The passenger's window switch operates
only the corresponding passenger's win-
dow. To open the window partially, push
the switch down lightly until the desired
window position is reached. To close the
window, pull the switch up until the desired
window position is reached.

Rear power window switch

The rear power window switches open or
close only the corresponding windows. To
open the window, push the switch and hold
it down

. To close the window, pull the

switch up

Automatic operation

To fully open a window equipped with auto-
matic operation, push the window switch
down to the second detent and release it;
it need not be held. The window automati-
cally opens all the way. To stop the win-
dow, lift the switch up while the window is
opening.

LIC4228

LIC2663

LIC0410

2-68

Instruments and controls

Auto-reverse function (if so
equipped)

If the control unit detects something caught
in the window as it is closing, the window will
be immediately lowered.

The auto-reverse function can be acti-
vated when the window is closed by auto-
matic operation when the ignition switch is
placed in the ON position or for a period of
time after the ignition switch is placed in
the OFF position.

Depending on the environment or driv-
ing conditions, the auto-reverse func-
tion may be activated if an impact or
load similar to something being caught
in the window occurs.

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the window.

When power window switch does
not operate

If the power window automatic function
(closing only) does not operate properly,
perform the following procedure to initial-
ize the power window system:

1. Place the ignition switch in the ON position.

2. Open the window more than halfway by

operating the power window switch.

3. Pull the power window switch and hold it

to close the window, and then hold the
switch more than 3 seconds after the
window is closed.

4. Release the power window switch. Oper-

ate the window by the automatic func-
tion to confirm the initialization is com-
plete. The power window automatically
opens or closes depending on if the au-
tomatic down or up function is selected.

5. Perform steps 2 through 4 above for

other windows.

If the power window function does not op-
erate properly after performing the above
procedure have the system checked and
repaired. It is recommended that you visit a
NISSAN dealer for this service.

The interior light has a three-position
switch and operates regardless of ignition
switch position.

When the switch is in the ON position

the interior lights illuminate, regardless of
door position. The lights will go off after a
period of time unless the ignition switch is
placed in the ON position.
When the switch is in the

position, the

interior lights will stay on for a period of
time when:
• The doors are unlocked by the key or the

power door lock switch while all doors are
closed and the ignition switch is placed in
the OFF position.

LIC3985

INTERIOR LIGHTS

Instruments and controls

2-69

• The driver’s door is opened and then

closed while the key is removed from the
ignition switch (if so equipped).

• The key is removed from the ignition

switch (if so equipped) while all doors are
closed.

The light will turn off while the timer is acti-
vated when:
• The driver’s door is locked by the key, or

the power door lock switch.

• The ignition switch is placed in the ON

position.

When the switch is in the OFF position

the interior lights do not illuminate, regard-
less of door position.

The lights will turn off automatically after a
period of time while doors are open to pre-
vent the battery from becoming discharged.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

MAP LIGHTS

To turn the map lights on, push the switch
to the

position. To turn them off, push

the switch to the

position.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

PERSONAL LIGHT

The personal light has a three-position
switch and operates regardless of ignition
switch position.

When the switch is in the ON position

the light illuminates, regardless of door
position.

When the switch is in the DOOR position

the light illuminates by opening a door.

LIC3988

SIC2063A

Center personal light

2-70

Instruments and controls

The personal light will stay on for about 15
seconds when:
• The doors are unlocked while the ignition

switch is placed in the OFF position and
all doors are closed.

• The driver's door is opened and then

closed while the ignition switch is placed
in the OFF position.

• The ignition switch is placed in the OFF

position while all doors are closed.

The personal light will turn off while the
15 second timer is activated when:
• The driver's door is locked by the key fob,

a key or the lock-unlock switch.

• The ignition switch is placed in the ON

position.

When the switch is in the OFF position

the light does not illuminate, regardless of
door position.

Some vehicles are equipped with a battery
saver feature that will automatically turn
off the interior lights after approximately
10 minutes if:
• doors are open, or
• the interior light switch is in the ON position.

NOTE:

If the interior lights are turned off auto-
matically by the battery saver feature,
the ignition switch must be placed in the
ON position before the interior lights will
illuminate again.

For information regarding the interior light
bulb replacement, see “Exterior and interior
lights” (P. 8-25).

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

TRUNK LIGHT

The light illuminates when the trunk lid is
opened. When the trunk lid is closed, the
light goes off.

The light will go off after a period of time if
the trunk lid is left open, unless the ignition
switch is placed in the ON position.

For additional information, see “Exterior
and interior lights” (P. 8-25).

Instruments and controls

2-71

A key number plate is supplied with your
keys. Record the key number and keep it
in a safe place (such as your wallet), not in
the vehicle. If you lose your keys, it is recom-
mended that you visit a NISSAN dealer for
duplicates by using the key number.
NISSAN does not record key numbers so it
is very important to keep track of your key
number plate.

A key number is only necessary when you
have lost all your keys. If you still have a key,
it can be duplicated without knowing the
key number.

NISSAN INTELLIGENT KEY® (if so
equipped)

Your vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key System com-
ponents and NISSAN Vehicle Immobilizer
System components.

Never leave these keys in the vehicle.

As many as four Intelligent Keys can be
registered and used with one vehicle. The
new keys must be registered prior to use
with the Intelligent Key System and NISSAN
Vehicle Immobilizer System of your vehicle.
Since the registration process requires
erasing all memory in the Intelligent Key
components when registering new keys,
be sure to take all Intelligent Keys that you
have to the NISSAN dealer.

LPD3050

1. Master key (two sets)
2. Key number plate

LDI3697

Type A (if so equipped)

1. Intelligent Keys (two sets)

2. Mechanical keys

3. Key number plate (one plate)

LDI3698

Type B (if so equipped)

KEYS

3-2

Pre-driving checks and adjustments

A key number plate is supplied with your
keys. Record the key number and keep it
in a safe place (such as your wallet), not in
the vehicle. If you lose your keys, it is recom-
mended that you visit a NISSAN dealer
for duplicates by using the key number.
NISSAN does not record key numbers so it
is very important to keep track of your key
number plate.

A key number is only necessary when you
have lost all keys and do not have one to
duplicate from. If you still have a key, it can
be duplicated without knowing the key
number.

CAUTION

Listed below are conditions or occur-
rences which will damage the Intelli-
gent Key:

•

Do not allow the Intelligent Key, which
contains electrical components, to
come into contact with water or salt
water. This could affect the system
function.

•

Do not drop the Intelligent Key.

•

Do not strike the Intelligent Key sharply
against another object.

•

Do not change or modify the Intelli-
gent Key.

•

Wetting may damage the Intelligent
Key. If the Intelligent Key gets wet,
immediately wipe until it is com-
pletely dry.

•

Do not place the Intelligent Key for an
extended period in an area where
temperatures exceed 140°F (60°C).

•

Do not attach the Intelligent Key with
a key holder that contains a magnet.

•

Do not place the Intelligent Key near
equipment that produces a magnetic
field, such as a TV, audio equipment
and personal computers.

If an Intelligent Key is lost or stolen, NISSAN
recommends erasing the ID code of that
Intelligent Key from the vehicle. This may
prevent the unauthorized use of the Intelli-
gent Key to operate the vehicle. For infor-
mation regarding the erasing procedure, it
is recommended that you visit a NISSAN
dealer.

Mechanical key

The Intelligent Key contains the mechani-
cal key.

To remove the mechanical key, release the
lock knob on the back of the Intelligent Key.

To install the mechanical key, firmly insert it
into the Intelligent Key until the lock knob
returns to the lock position.

Use the mechanical key to lock or unlock the
driver’s door and trunk lid (if so equipped).

For additional information, see “Doors”
(P. 3-4) and “Trunk lid” (P. 3-24).

LPD3338

Pre-driving checks and adjustments

3-3

CAUTION

Always carry the mechanical key in-
stalled in the Intelligent Key slot.

NISSAN VEHICLE IMMOBILIZER
SYSTEM KEYS

Additional or replacement keys:

If you still have a key, the key number is not
necessary when you need extra NISSAN
Vehicle Immobilizer System keys. Your ex-
isting key can be duplicated without know-
ing the key number. As many as four
NISSAN Vehicle Immobilizer System keys
can be used with one vehicle. You should
bring all NISSAN Vehicle Immobilizer Sys-
tem keys that you have to the NISSAN
dealer for registration. This is because the
registration process will erase the memory
of all key codes previously registered into
the NISSAN Vehicle Immobilizer System. Af-
ter the registration process, these compo-
nents will only recognize keys coded into
the NISSAN Vehicle Immobilizer System
during registration. Any virtual key acces-
sories (if so equipped) will also have to be
reregistered. Any key that is not given to the
dealer at the time of registration will no
longer be able to start your vehicle.

CAUTION

Do not allow the immobilizer system
key, which contains an electrical tran-
sponder, to come into contact with wa-
ter or salt water. This could affect sys-
tem function.

When the doors are locked using one of the
following methods, the doors cannot be
opened using the inside or outside door
handles. The doors must be unlocked to
open the doors.

WARNING

•

Always have the doors locked while
driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping to
prevent persons from being thrown
from the vehicle. This also helps keep
children and others from uninten-
tionally opening the doors, and will
help keep out intruders.

•

Before opening any door, always look
for and avoid oncoming traffic.

DOORS

3-4

Pre-driving checks and adjustments

•

LOCKING WITH KEY

To lock or unlock the vehicle, turn the key as
shown.

Manual

To lock a door, turn the key toward the front
of the vehicle

. To unlock, turn the key

toward the rear of the vehicle

Selective open (if so equipped)

The power door lock system allows you to
lock or unlock all doors at the same time.

Turning the key toward the front

of the

vehicle locks all doors.

Turning the key one time toward the rear

of the vehicle unlocks that door. From

that position, returning the key to neutral

(where the key can only be removed

and inserted) and turning it toward the rear
again within 5 seconds unlocks all doors

LPD3048

Driver’s side

LPD3049

Pre-driving checks and adjustments

3-5

LOCKING WITH INSIDE LOCK KNOB

To lock the door without the key, move the
inside lock knob to the lock position

then close the door.

To unlock the door without the key, move
the inside lock knob to the unlock position

LOCKING WITH POWER DOOR
LOCK SWITCH

To lock all the doors without a key, push the
door lock switch (driver's or front passen-
ger's side) to the lock position

. When

locking the door this way, be certain not to
leave the key inside the vehicle.

To unlock all the doors without a key, push
the door lock switch (driver's or front pas-
senger's side) to the unlock position

Lockout protection

When any door is open and the power door
lock switch is moved to the lock position,
all doors will lock. If the Intelligent Key is left
in the vehicle after all the doors are closed,
all doors will unlock automatically and a
chime will sound.

These functions help to prevent the Intelli-
gent Key from being accidentally locked
inside the vehicle.

AUTOMATIC DOOR LOCKS

All doors lock automatically when the ve-
hicle speed reaches 15 mph (24 km/h).
• Continuously Variable Transmission (CVT)

(if so equipped)

All doors (if so equipped) or driver’s door
unlock automatically when the trans-
mission is placed in the P (Park) position,
the ignition switch is placed in the OFF
position or the key is removed from igni-
tion switch.

• Manual transmission (if so equipped)

All doors (if so equipped) or driver’s door
unlock automatically when the ignition
switch is placed in the OFF position or the
key is removed from the ignition switch.

LPD3041

LPD2309

3-6

Pre-driving checks and adjustments

NOTE:

On some vehicles, the automatic door
unlock function can be changed using
the “Vehicle Settings” of the vehicle in-
formation display.
For additional information, see “Vehicle
information display” (P. 2-25).

CHILD SAFETY REAR DOOR LOCK

Child safety locks help prevent the rear
doors from being opened accidentally, espe-
cially when small children are in the vehicle.

The child safety lock levers are located on
the edge of the rear doors.

When the lever is in the unlock position

the door can be opened from the outside
or the inside.

When the lever is in the LOCK position

the door can be opened only from the
outside.

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the electric medical equipment manu-
facturer for the possible influences
before use.

•

The Intelligent Key transmits radio
waves when the buttons are pressed.
The FAA advises the radio waves may
affect aircraft navigation and com-
munication systems. Do not operate
the Intelligent Key while on an air-
plane. Make sure the buttons are not
operated unintentionally when the
unit is stored for a flight.

•

Make sure to engage the P (Park) po-
sition and apply the parking brake
when parking your vehicle, entering
or exiting the vehicle or loading lug-
gage. Failure to do so could cause the
vehicle to move or roll away unex-
pectedly and result in serious per-
sonal injury or property damage.

SPA2037

NISSAN INTELLIGENT KEY® SYSTEM
(if so equipped)

Pre-driving checks and adjustments

3-7

The Intelligent Key can operate all the door
locks using the remote control function or
pushing the request switch (if so equipped)
on the vehicle without taking the key out
from a pocket or purse. The operating en-
vironment and/or conditions may affect
the Intelligent Key operation.

Be sure to read the following before using
the Intelligent Key.

CAUTION

•

Be sure to carry the Intelligent Key
with you when operating the vehicle.

•

Never leave the Intelligent Key in the
vehicle when you leave the vehicle.

The Intelligent Key is always communicating
with the vehicle as it receives radio waves.
The Intelligent Key transmits weak radio
waves. Environmental conditions may inter-
fere with the operation of the Intelligent Key
under the following operating conditions:
• When operating near a location where

strong radio waves are transmitted, such
as a TV tower, power station and broad-
casting station.

• When in possession of wireless equip-

ment, such as a cellular telephone, trans-
ceiver, or a CB radio.

• When the Intelligent Key is in contact with

or covered by metallic materials.

• When any type of radio wave remote con-

trol is used nearby.

• When the Intelligent Key is placed near an

electric appliance such as a personal
computer.

• When the vehicle is parked near a parking

meter.

In such cases, correct the operating condi-
tions before using the Intelligent Key func-
tion or use the mechanical key.

Although the life of the battery varies de-
pending on the operating conditions, the
battery’s life is approximately two years. If
the battery is discharged, replace it with a
new one.

When the Intelligent Key battery is low, the
NISSAN Intelligent Key® warning light (if so
equipped) will blink green for about 30 sec-
onds after the ignition switch is placed in
the ON position.

Since the Intelligent Key is continuously re-
ceiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and per-
sonal computer, the battery life may be-
come shorter.

When the battery is discharged, firmly ap-
ply the foot brake and touch the ignition
switch with the Intelligent Key. Then push
the ignition switch while depressing the
brake pedal within 10 seconds after the
chime sound. For additional information,
see “Push-button ignition switch” (P. 5-12).

For additional information, see “Battery re-
placement” (P. 8-22).

As many as four Intelligent Keys can be
registered and used with one vehicle. For
information about the purchase and use of
additional Intelligent Keys, it is recom-
mended that you visit a NISSAN dealer.

CAUTION

Listed below are conditions or occur-
rences which will damage the Intelli-
gent Key:

•

Do not allow the Intelligent Key, which
contains electrical components, to
come into contact with water or salt
water. This could affect the system
function.

•

Do not drop the Intelligent Key.

•

Do not strike the Intelligent Key sharply
against another object.

3-8

Pre-driving checks and adjustments

•

Do not change or modify the Intelli-
gent Key.

•

Wetting may damage the Intelligent
Key. If the Intelligent Key gets wet,
immediately wipe until it is com-
pletely dry.

•

If the outside temperature is below
14°F (-10°C) the battery of the Intelli-
gent Key may not function properly.

•

Do not place the Intelligent Key for an
extended period in an area where
temperatures exceed 140°F (60°C).

•

Do not attach the Intelligent Key with
a key holder that contains a magnet.

•

Do not place the Intelligent Key near
equipment that produces a magnetic
field, such as a TV, audio equipment
and personal computers.

OPERATING RANGE

The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range from the request
switch (if so equipped)

When the Intelligent Key battery is dis-
charged or strong radio waves are present
near the operating location, the Intelligent
Key operating range becomes narrower,
and the Intelligent Key may not function
properly.

The operating range is within 31.5 in (80 cm)
from each request switch (if so equipped)

If the Intelligent Key is too close to the door
glass, handle or rear bumper, the request
switches (if so equipped) may not function.

When the Intelligent Key is within the oper-
ating range, it is possible for anyone, even
someone who does not carry the Intelli-
gent Key, to push the request switch (if so
equipped) to lock/unlock the doors.

LPD3043

Pre-driving checks and adjustments

3-9

DOOR LOCKS/UNLOCKS
PRECAUTION

• Do not push the door handle request

switch (if so equipped) with the Intelligent
Key held in your hand as illustrated. The
close distance to the door handle will
cause the Intelligent Key system to have
difficulty recognizing that the Intelligent
Key is outside the vehicle.

• After locking with the door handle request

switch (if so equipped), verify the doors are
securely locked by testing them.

• To prevent the Intelligent Key from being

left inside the vehicle, make sure you
carry the Intelligent Key with you and then
lock the doors.

• Do not pull the door handle before push-

ing the door handle request switch (if so
equipped). The door will be unlocked but
will not open. Release the door handle
once and pull it again to open the door.

NISSAN INTELLIGENT KEY®
OPERATION

You can lock or unlock the doors without
taking the Intelligent Key out of your pocket
or bag.

When you carry the Intelligent Key with you,
you can lock or unlock all doors by push-
ing the door handle request switch (if so
equipped) within the range of operation.

LPD2554

LPD3039

3-10

Pre-driving checks and adjustments

Locking doors

1. Move the shift lever to the P (Park) posi-

tion, place the ignition switch in the LOCK
position and make sure you carry the
Intelligent Key with you.

2. Close all doors.

3. Push any door handle request switch

(if so equipped)

while carrying the

Intelligent Key with you.

4. All doors will lock.

5. The hazard indicator lights flash twice

and the outside buzzer sounds twice.

NOTE:
• Doors lock with the door handle re-

quest switch (if so equipped) while
the ignition switch is not in the LOCK
position.

• Doors do not lock by pushing the pas-

senger door handle request switch
(if so equipped) while any door is open.
However, doors lock with the mechani-
cal key even if any door is open.

• Request switches (if so equipped) for

all doors can be deactivated when the
Ext. Door Switch feature is switched to
OFF using the “Vehicle Settings” menu
in the vehicle information display. For
additional information, see “Vehicle
information display” (P. 2-25).

• Doors do not lock with the door handle

request switch (if so equipped) with
the Intelligent Key inside the vehicle
and a beep sounds to warn you. How-
ever, when an Intelligent Key is inside
the vehicle, doors can be locked with
another Intelligent Key.

WARNING

After locking the doors using the re-
quest switch (if so equipped), make
sure that the doors have been securely
locked by operating the door handles.
Failure to follow these instructions may
result in inadvertently unlocking the
doors, which may decrease the safety
and security of your vehicle.

LDI3699

LPD2165

Pre-driving checks and adjustments

3-11

CAUTION

•

When locking the doors using the re-
quest switch (if so equipped), make
sure to have the Intelligent Key in
your possession before operating
the request switch (if so equipped) to
prevent the Intelligent Key from be-
ing left in the vehicle.

•

The request switch (if so equipped) is
operational only when the Intelligent
Key has been detected by the Intelli-
gent Key system.

Lockout protection

To prevent the Intelligent Key from being
accidentally locked in the vehicle, lockout
protection is equipped with the Intelligent
Key.

When the driver’s side door is open, the
doors are locked and then the Intelligent
Key is put inside the vehicle and all the
doors are closed; the lock will automati-
cally unlock and the door buzzer sounds.

NOTE:

The doors may not lock when the Intelli-
gent Key is in the same hand that is oper-
ating the request switch (if so equipped)
to lock the door. Put the Intelligent Key in a
purse, pocket or your other hand.

CAUTION

The lockout protection may not func-
tion under the following conditions:

•

When the Intelligent Key is placed on
top of the instrument panel.

•

When the Intelligent Key is placed on
top of the rear parcel shelf.

•

When the Intelligent Key is placed in-
side the glove box or a storage bin.

•

When the Intelligent Key is placed in-
side the door pockets.

•

When the Intelligent Key is placed on
or under the spare tire area.

•

When the Intelligent Key is placed in-
side or near metallic materials.

Unlocking doors

1. Carry the Intelligent Key.

2. Push the door handle request switch

(if so equipped)

3. The hazard indicator lights flash once

and the outside buzzer sounds once.

4. Push the door handle request switch

(if so equipped)

again within 1 minute

to unlock all doors.

LDI3699

3-12

Pre-driving checks and adjustments

NOTE:

Request switches (if so equipped) for all
doors can be deactivated when the Ext.
Door Switch feature is switched to OFF
using the “Vehicle Settings” menu on the
vehicle information display. For addi-
tional information, see “Vehicle informa-
tion display” (P. 2-25).

If a door handle is pulled while unlocking
the doors, that door may not be unlocked.
Returning the door handle to its original
position will unlock the door. If the door
does not unlock after returning the door
handle, push the door handle request
switch (if so equipped) to unlock the door.

All doors will be locked automatically un-
less one of the following operations is per-
formed within 1 minute after pushing the
request switch (if so equipped).
• Opening any door.
• Pushing the ignition switch.

Using the interior light

The interior light illuminates for a period of
time when a door is unlocked and the inte-
rior light switch is not in the OFF position.

The light can be turned off without waiting by
performing one of the following operations:
• Placing the ignition switch in the ON

position.

• Locking the doors with the remote control.
• Switching the interior light switch to the

OFF position.

• Switching the Auto Room Lamp feature

to the OFF position in the “Vehicle Set-
tings” menu on the vehicle information
display. For additional information, see
“Vehicle information display” (P. 2-25).

For additional information, see “Interior
lights” (P. 2-69).

Opening the trunk lid

1. Unlock all doors.

2. Push the trunk opener switch (if so

equipped)

while carrying the Intelli-

gent Key with you.

3. The trunk will unlatch. A chime will sound

four times.

4. Raise the trunk lid to open the trunk.

LPD2165

LPD3047

Pre-driving checks and adjustments

3-13

Nissan Versa (2024 year). Manual in english - page 5