Nissan Versa (2024 year). Manual in english

When the ignition switch is placed in the ON
position, the power steering warning light
illuminates. After starting the engine, the
power steering warning light turns off. This
indicates the power steering is operational.

If the power steering warning light illumi-
nates while the engine is running, it may
indicate the power steering is not function-
ing properly and may need servicing. Have
the power steering checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

When the power steering warning light illu-
minates with the engine running, there will
be no power assist for the steering, but you
will still have control of the vehicle. At this
time, greater steering effort is required to
operate the steering wheel, especially in
sharp turns and at low speeds.

For additional information, see “Power
steering” (P. 5-116).

Rear Automatic Braking
(RAB) system warning light

This light comes on when the ignition
switch is placed in the ON position. It turns
off after the engine is started.

This light illuminates when the RAB system
is set to off in the vehicle information dis-
play, set to off using the Automatic Emer-
gency Braking with Pedestrian Detection
OFF switch (if so equipped), or the Vehicle
Dynamic Control (VDC) system is turned
off.

If the light illuminates when the RAB sys-
tem is on, it may indicate that the system is
unavailable. For additional information, see
“Rear Automatic Braking (RAB)” (P. 5-76).

Shift P (Park) warning light
(if so equipped)

This light blinks red and the key reminder
chime sounds if the shift lever is in any
position other than P (Park) and the ignition
switch is in the OFF position. Return the
shift lever to P (Park) with the ignition
switch in the OFF position and the light will
turn off. Place the ignition switch in the
LOCK position and the chime will turn off.
For additional information, see “NISSAN In-
telligent Key®” (P. 3-2).

Slip indicator light

This indicator light will blink when the Ve-
hicle Dynamic Control (VDC) system is op-
erating, thus alerting the driver to the fact
that the road surface is slippery and the
vehicle is nearing its traction limits.

You may feel or hear the system working;
this is normal.

The light will blink for a few seconds after
the VDC system stops limiting wheel spin.

The

indicator light also comes on

when you place the ignition switch in the
ON position. The light will turn off after
approximately 2 seconds if the system is
operational. If the light does not come on
have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Vehicle Dynamic Control
(VDC) OFF indicator light

This indicator light comes on when the
VDC is turned off in the vehicle information
display (if so equipped) or by pushing the
VDC OFF switch (if so equipped). This indi-
cates the VDC has been turned off.

2-22

Instruments and controls

Turn the VDC on using the vehicle informa-
tion display (if so equipped) or by restarting
the engine. For additional information, see
“Vehicle Dynamic Control (VDC) system”
(P. 5-119).

The VDC light also comes on when the ig-
nition switch is placed in the ON position.
The light will turn off after a period of time if
the system is operational. If the light stays
on or comes on along with the

indica-

tor light while you are driving, have the VDC
system checked. It is recommended that
you visit a NISSAN dealer for this service.

WARNING

VDC should remain on unless freeing a
vehicle from mud or snow.

While the VDC system is operating, you
might feel a slight vibration or hear the sys-
tem working when starting the vehicle or
accelerating, but this is normal.

WARNING/INDICATOR LIGHTS
(other)

For additional information, see “Vehicle in-
formation display” (P. 2-25).

CRUISE indicator light
(green) (if so equipped)

The light comes on when the cruise control
switch is pushed. The light goes out when
the switch is pushed again. When the
cruise indicator light comes on, the cruise
control system is operational. For addi-
tional information, see “Cruise control”
(P. 5-51).

Front fog light indicator
light (green) (if so equipped)

The front fog light indicator light illumi-
nates when the front fog lights are on.
For additional information, see “Fog light
switch” (P. 2-51).

High Beam Assist indicator
light (green)

This indicator light illuminates when the
headlights come on while the headlight
switch is in the AUTO position with the high
beams selected. This indicates that the
high beam assist is operational.

For additional information, see “Headlight
and turn signal switch” (P. 2-45).

High beam indicator light
(blue)

This blue light comes on when the head-
light high beams are on and goes out when
the low beams are selected.

The high beam indicator light also comes
on when the passing signal is activated.

Lane Departure Warning
(LDW) indicator light (green)
(if so equipped)

This indicator light will blink when the LDW
system is operating.

For additional information, see “Lane De-
parture Warning (LDW)” (P. 5-26).

Instruments and controls

2-23

NISSAN Intelligent Key®
warning light (green)
(if so equipped)

After the ignition switch is placed in the ON
position, this light comes on for about 2
seconds and then turns off. This light illumi-
nates or blinks as follows:
• The light blinks in green when the Intelli-

gent Key battery is running out of power.
Replace the battery with a new one. For
additional information, see “Battery re-
placement” (P. 8-22).

If the warning light illuminates in yellow
while the engine is stopped, it may be im-
possible to free the steering lock or to start
the engine. If the light comes on while the
engine is running, you can drive the vehicle.
However, in these cases, have the vehicle
checked and repaired as soon as possible.
It is recommended that you visit a NISSAN
dealer for this service.

For additional information, see “NISSAN
Intelligent Key®” (P. 3-2).

SET indicator light (green)
(if so equipped)

This light comes on while the vehicle speed
is controlled by the cruise control system.
If the light blinks while the engine is run-
ning, it may indicate the cruise control sys-
tem is not functioning properly. Have the
system checked. It is recommended that
you visit a NISSAN dealer for this service.
For additional information, see “Cruise con-
trol” (P. 5-51).

Side light and headlight
indicator light (green)

The side light and headlight indicator light
illuminates when the side light or head-
lights are on. If the headlight switch is in the
AUTO position, the side light and headlight
indicator light will illuminate when the
headlights turn on. For additional informa-
tion, see “Headlight and turn signal switch”
(P. 2-45).

SPORT mode indicator light
(green) (if so equipped)

This light illuminates and then turns off
when the ignition switch is placed in the ON
position, and when the SPORT mode is
selected.

For additional information, see “Drive Sport
mode switch” (P. 5-22).

Turn signal/hazard
indicator lights (green)

The appropriate light flashes when the turn
signal switch is activated.

NOTE:

In case of a turn signal light bulb mal-
function, the turn signal will flash at a
higher frequency when the turn signal
switch is activated.

Both lights flash when the hazard switch is
turned on.

For additional information, see “Lights”
(P. 8-24).

2-24

Instruments and controls

AUDIBLE REMINDERS
Brake pad wear warning

The disc brake pads have audible wear
warnings. When a disc brake pad requires
replacement, it makes a high pitched
scraping sound when the vehicle is in mo-
tion, whether or not the brake pedal is de-
pressed. Have the brakes checked as soon
as possible if the warning sound is heard.
It is recommended that you visit a NISSAN
dealer for this service.

Light reminder chime

With the ignition switch placed in the OFF
position, a chime sounds when the driver's
door is opened if the headlights or parking
lights are on.

Turn the headlight control switch off or to
AUTO before leaving the vehicle.

NISSAN Intelligent Key® door
buzzer (if so equipped)

The Intelligent Key door buzzer sounds if any
one of the following improper operations is
found.
• The Intelligent Key is left inside the vehicle

when locking the doors.

• The Intelligent Key is taken outside the

vehicle when operating the vehicle.

When the buzzer sounds, be sure to check
both the vehicle and the Intelligent Key
System. For additional information, see
“NISSAN Intelligent Key®” (P. 3-2).

Parking brake reminder chime

A chime sounds if the parking brake is set
and the vehicle is driven. The chime will
stop if the parking brake is released or the
vehicle speed returns to zero.

The vehicle information display is located
to the left of the speedometer. It displays
such items as:
• Audio Information
• Drive Computer Information
• Fuel Economy Information
• Indicators and Warnings
• Vehicle and Meter Display Settings
• Odometer/twin trip odometer
• Gear Position Indicator (P, R, N, D, L)
• Distance To Empty and Fuel Indicator
• Tire pressures

LIC3565

VEHICLE INFORMATION DISPLAY
(if so equipped)

Instruments and controls

2-25

HOW TO USE THE VEHICLE
INFORMATION DISPLAY

The vehicle information display can be
changed using the

, and OK buttons located on the steer-

ing wheel.

䊊

- Use these buttons

to navigate the vehicle information
display.

䊊

OK - Change or select an item in the
vehicle information display.

䊊

(if so equipped) — Returns to the

previous menu.

The OK,

and

buttons also

control audio and control panel functions
in some conditions. Most screens and
menus offer instruction prompts of the
steering switch buttons to indicate how to
control the vehicle information display.
Dots on the left side of the vehicle informa-
tion display will appear if there is more than
one page of menu items. The OK button
changes the audio source and the

buttons also control voice recognition

manual mode. For additional information,
refer to the separate NissanConnect®
Owner’s Manual.

STARTUP DISPLAY

When the vehicle in placed in the ON posi-
tion the screens that display in the vehicle
information display include:
• Gauges
• Audio
• Fuel Economy
• Drive Computer
• Warning Review
• Driving Aids
• Settings

For additional information on warnings
and indicators, see “Vehicle information
display” (P. 2-25).

To control what items display in the vehicle
information display, see “Customize dis-
play” (P. 2-31).

LIC3566

2-26

Instruments and controls

1. Vehicle speed (mph or km/h)

The vehicle speed mode shows the current
vehicle speed and the average vehicle
speed since the last reset.

Average vehicle speed:

Press the

buttons on the steering

wheel for longer than 1.5 seconds to reset.

The average vehicle display is updated ev-
ery 30 seconds. the first 30 seconds after a
rest, the display shows “– – –’

2. Elapsed time and trip odometer

Elapsed time:

The elapsed time shows the time since the
last reset. Press the

buttons on the

steering wheel for longer than 1.5 seconds
to reset. The trip odometer is also reset at
the same time.

Trip odometer:

The trip odometer shows the total dis-
tance the vehicle has been driven since the
last reset. Press the

buttons on the

steering wheel for longer than 1.5 seconds
to reset. The elapsed time is also reset at
the same time.

3. Fuel economy display

Current fuel consumption:

The

current

fuel

consumption

mode

shows the current fuel consumption.

Average fuel consumption:

The average fuel consumption mode
shows the average fuel consumption since
the last reset. Press the

buttons on

the steering wheel for longer than 1.5 sec-
onds to reset.

The display is updated every 30 seconds.
For about the first 1/3 of a mile (500 m) after
a reset, the display shows “– –.”

The average fuel consumption is also rest
in the lower display. For additional informa-
tion, refer to the separate NissanConnect®
Owner's Manual.

4. Navigation (if so equipped)

When the route guidance is set in the navi-
gation system, this item shows the naviga-
tion route information.

5. Audio

The audio mode shows the status of audio
information.

6. Driving Aids

The driving aids mode shows the operat-
ing condition for the following systems (if
so equipped):
• Forward

–– Automatic Emergency Braking (AEB)

with Pedestrian Detection system

–– Intelligent Forward Collision Warning

(I-FCW)

• Lane:

–– Lane Departure Warning (LDW)

• Blind Spot:

–– Blind Spot Warning (BSW)

For additional information, see “Blind Spot
Warning (BSW)” (P. 5-33), “Lane Departure
Warning (LDW)” (P. 5-26), “Automatic Emer-
gency Braking (AEB) with Pedestrian Detec-
tion” (P. 5-83), or “Intelligent Forward Colli-
sion Warning (I-FCW)” (P. 5-96).

7. Tire Pressures

The tire pressure mode shows the pressure
of all four tires while the vehicle is driven.

When the “Tire Pressure Low — Add Air”
warning appears, the display can be
switched to the tire pressure mode by
pressing the

buttons to reveal addi-

tional details on the displayed warning.

2-28

Instruments and controls

For additional information, see “Low tire
pressure warning light” (P. 2-18), “Tire Pres-
sure Monitoring System (TPMS)” (P. 5-5), “Flat
tire” (P. 6-3) and “Types of tires” (P. 8-35)

8. Compass

This display indicates the direction the ve-
hicle is heading.

SETTINGS

The setting mode allows you to change the
information displayed in the vehicle infor-
mation display as well as the model for
several vehicle functions:
• VDC Setting
• Driver Assistance
• Customize Display

• Vehicle Settings
• TPMS Settings
• Maintenance
• Clock
• Unit/Language
• Factory Reset

VDC Setting

The VDC Setting menu allows the user to enable or disable the Vehicle Dynamic Control (VDC) system.

Menu item

Explanation

System

Allows the user to turn the VDC system on or off. For additional information, see “Vehicle Dynamic Control
(VDC) system” (P. 5-119).

Driver Assistance

The driver assistance menu allows the user to change the various driving aids and assistance options.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Lane

Displays the available lane options.

Lane Departure
Warning

Allows user to turn the Lane Departure Warning (LDW) system on or off. For additional information, see “Lane
Departure Warning (LDW) ” (P. 5-26).

Blind Spot

Displays the available blind spot options.

Instruments and controls

2-29

Menu item

Explanation

Blind Spot Warning

Allows user to turn the Blind Spot Warning (BSW) system on or off. For additional information, see “Blind Spot
Warning (BSW) ” (P. 5-33).

Side Indicator
Brightness

Allows user to change the brightness of the side indicator.

Emergency Brake

Displays the available emergency braking options.

Front

Allows user to turn the front emergency braking system on or off. For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian Detection” (P. 5-83).

Rear

Allows user to turn the rear emergency braking system on or off. For additional information, see “Rear Automatic
Braking (RAB)” (P. 5-76).

Parking Aids

Displays the available parking aids options.

Sonar

Displays the available sonar options. For additional information, see “Rear Sonar System” (RSS) (P. 5-122).

Rear Sensor

Allows user to turn the rear sensor on or off.

Display

Allows user to turn the display on or off.

Volume

Allows user to adjust the volume to High/Med/Low.

Range

Allows user to adjust the range to Far/Mid/Near.

Cross Traffic

Allows user to turn rear cross traffic alert on or off. For additional information, see “Rear Cross Traffic Alert (RCTA)”
(P. 5-43).

Driver Attention Alert

Allows user to turn the Intelligent Driver Alertness (I-DA) system on or off. For additional information, see “Intelli-
gent Driver Alertness” (I-DA) (P. 5-111).

Timer Alert

Allows user to set or reset an alert at a specific time interval.

Low Temperature Alert

Allows user to turn the low temperature alert on or off.

2-30

Instruments and controls

Customize Display

The customize display menu allows the user to customize the information that appears in the vehicle information display.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Main Menu Selection

Displays available screens that can be shown in the vehicle information display.

Home

Allows user to turn the status screen on or off in the vehicle information display.

Drive Computer

Allows user to turn the drive computer screen on or off in the vehicle information display.

Driving Aids

Allows user to turn the driving aids screen on or off in the vehicle information display.

Tire Pressures

Allows user to turn the tire pressures screen on or off in the vehicle information display.

Coolant Temp.

Allows user to turn the coolant temp. screen on or off in the vehicle information display.

CRUISE

Allows user to turn the cruise control screen on or off in the vehicle information display.

ECO Info Settings

Displays the available ECO info settings.

ECO Drive Report

Select to display this report when the ignition in switch is placed in the ON position.

View History

Select to view the vehicle’s history.

Welcome Effect

Displays the available welcome effect settings.

Gauges

Allows user to turn the gauges effect on or off.

Animation

Allows user to turn the animation effect on or off.

Instruments and controls

2-31

Vehicle Settings

The vehicle settings allow the user to change the settings for lights, wipers, locking, keys, and other vehicle settings.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Rear Door Alert

Displays the available Rear Door Alert options. For additional information, see “Rear Door Alert” (P. 2-61).

Horn & Alert

When selected, the alert is displayed and the horn sounds.

Alert Only

When selected, only the alert is displayed.

No horn, No Alert

When selected, no alert or horn will be active.

Lighting

Displays the available lighting settings.

Welcome Headlight

Displays the available welcome headlight options.

Welcome & Farewell

Allows user to set the headlights to turn on when they approach and leave the vehicle.

Welcome

Allows user to set the headlights to turn on when they approach the vehicle.

Farewell

Allows user to set the headlights to turn on when they leave the vehicle.

OFF

Allows user to set the headlights to turn off when not driving.

Auto Room Lamp

Allows user to turn the auto room lamp on or off.

Light Sensitivity

Allows user to change when the lights illuminate based on the brightness outside the vehicle.

Auto Light

Allows user to turn the auto light feature on or off.

Light Off Delay

Allows user to change the duration of time, from 0 to 180 seconds, that the automatic headlights stay on
after the vehicle is shut off.

Turn Indicator

Displays the available turn indicator settings.

3 Flash Pass

Allows user to turn the 3 flash pass feature on or off. For additional information, see “Headlight and turn
signal switch” (P. 2-45).

2-32

Instruments and controls

Menu item

Explanation

Locking

Displays the available locking settings.

Ext. Door Switch

Allows user to turn the exterior door switch on or off. When turned on, the request switch on the door is
activated.

Selective Unlock

Allows user to turn the selective unlock feature on or off. When turned on, only the driver’s door is unlocked
after the door unlock operation. When the door handle request switch on the driver’s or front passenger’s
side door is pushed to be unlocked, only the corresponding door is unlocked first. All the doors can be un-
locked if the door unlock operation is performed again within 30 seconds. When this item is turned off,
all the doors will be unlocked after the door unlock operation is performed once.

Auto Door Unlock

Displays the available auto door unlock options.

Shift to P

Doors will unlock when the vehicle is shifted into P (Park).

IGN OFF

Doors will unlock when the ignition is turned off.

OFF

Doors will have to be manually unlocked.

Answer Back Horn

Allows user to turn the answer back horn feature on or off. When turned on, the horn will chirp and the haz-
ard indicators will flash twice when locking the vehicle with the Intelligent Key.

Walk Away Lock

Allows the user to turn the walk away lock function ON or OFF. For additional information, see “Walk away lock
function” (P. 3-17).

Approach Unlock

Allows the user to turn the approach unlock function ON or OFF. For additional information, see “Approach
unlock function” (P. 3-17).

Wipers

Displays the available wipers settings.

Speed Dependent

Allows user to turn the speed dependent feature on or off.

Remote Engine Start

Allows user to turn the Remote Engine Start feature on or off. When turned off, the vehicle cannot be started
remotely. For additional information, see “Remote Engine Start” (P. 3-20).

Instruments and controls

2-33

TPMS Settings

The TPMS settings menu allows the user to change the tire pressure units displayed in the vehicle information display.

Menu item

Explanation

TPMS Settings

Displays available TPMS Settings.

Tire Pressure Unit

Allows user to select the tire pressure units that will display in the vehicle information display.

Maintenance

The maintenance menu allows the user to set reminders for various vehicle maintenance items.

WARNING

The tire replacement indicator is not a substitute for regular tire checks, including tire pressure checks. For additional informa-
tion, see “Changing wheels and tires” (P. 8-37). Many factors including tire inflation, alignment, driving habits and road conditions
affect tire wear and when tires should be replaced. Setting the tire replacement indicator for a certain driving distance does not
mean your tires will last that long. Use the tire replacement indicator as a guide only and always perform regular tire checks.
Failure to perform regular tire checks, including tire pressure checks could result in tire failure. Serious vehicle damage could
occur and may lead to a collision, which could result in serious personal injury or death.

Menu item

Explanation

Oil and Filter

Allows user to set a reminder at a specific interval or reset the current one.

Tire

Allows user to set a reminder at a specific interval or reset the current one.

Other

Allows user to set a reminder at a specific interval or reset the current one.

2-34

Instruments and controls

Clock

Menu item

Explanation

Clock

Allows user to adjust the clock settings and time within the vehicle information display. Adjustments that can
be made include manually setting the time and 12H/24H format.
If these options do not appear, the clock must be set within the center display. For additional information,
refer to the separate NissanConnect® Owner’s Manual (if so equipped).

Unit/Language

The unit/language menu allows the user to change the units shown in the vehicle information display.

Menu item

Explanation

Mileage/Fuel

Displays the available mileage/fuel display units and allows user to select preferred unit for display.

Tire Pressures

Allows user to select the tire pressure display units.

Temperature

Allows user to select the temperature display units.

Language

Displays the available language options and allows user to select preferred language for display.

Factory Reset

The factory reset menu allows the user to restore the vehicle information display settings to factory status.

Menu item

Explanation

Factory Reset

Allows user to reset the vehicle information display settings to the original factory settings. Once selected,
the user can confirm or cancel the reset.

Instruments and controls

2-35

VEHICLE INFORMATION DISPLAY
WARNINGS AND INDICATORS

The following messages may appear in
your vehicle information display.

I-Key System Error: See
Owner’s Manual

After the ignition switch is pushed to the
ON position, this warning appears for a pe-
riod of time and then turns off.

The I-Key System Error message warns of
a malfunction with the Intelligent Key sys-
tem. If the warning appears on while the
engine is stopped, it may be impossible to
start the engine.

If the warning appears on while the engine
is running, you can drive the vehicle. How-
ever, in these cases, have the system
checked. It is recommended that you visit a
NISSAN dealer for this service.

Key Battery Low

This indicator appears when the Intelligent
Key battery is running out of power.

If this indicator appears, replace the bat-
tery with a new one. For additional infor-
mation, see “Battery replacement” (P. 8-22).

No Key Detected

This warning appears when the Intelligent
Key is left outside the vehicle with the igni-
tion switch in the ON position. Make sure
the Intelligent Key is inside the vehicle.

For additional information, see “NISSAN In-
telligent Key®” (P. 3-7).

Alarm - Time for a break?

This indicator appears when the driver en-
ables the Timer Alert function within the
Driver Assistance settings and the selected
set time is expired. The time is based on
ignition on time and can be set up to six
hours.

Brightness indicator

This indicator shows the brightness ad-
justment of the instrument panel. For addi-
tional information, see “Instrument bright-
ness control” (P. 2-50).

Check Back Seat For All Articles

When the system is enabled, this message
appears when the vehicle comes to a com-
plete stop, the vehicle is transitioned from

the D (Drive) position to P (Park) position,
and the driver exits the vehicle. This mes-
sage alerts the driver, after a period of time,
to check for items in the rear seat after the
audible alert has been provided.

NOTE:

This system is disabled until a driver en-
ables it using the vehicle information
display. For additional information, see
“How to use the vehicle information dis-
play” (P. 2-25).

For additional information, see “Rear Door
Alert” (P. 2-61).

CVT Error: See Owner's
Manual

This warning appears when there is a prob-
lem with the CVT system. If this warning ap-
pears, have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Door/Trunk Open

This warning appears when a door or the
trunk has been opened.

2-36

Instruments and controls

Drive sport mode indicator

A small “S” appears to the right of the Trans-
mission Shift Position indicator in the ve-
hicle information display when the drive
sport mode is engaged.
Activate the drive sport mode by pressing
the switch on the shift lever while the shift
lever is in the D (Drive) position.
For additional information, see “Driving the
vehicle” (P. 5-18).

Engine start operation
(for Continuously Variable
Transmission (CVT) models)

This indicator appears when the shift lever
is in the P (Park) position.
This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed. You can start
the engine directly in any position of the
ignition switch.

Engine start operation for
Intelligent Key system
(if I-Key battery level is low)

This indicator appears when the battery of
the Intelligent Key is low and when the
Intelligent Key system and the vehicle are
not communicating normally.

If this appears, touch the ignition switch
with the Intelligent Key while depressing
the brake pedal. For additional information,
see “NISSAN Intelligent Key® battery dis-
charge” (P. 5-15).

Headlight System Error: See Owner’s
Manual

This warning appears when there is an
error with the system. For additional informa-
tion, see “Headlight and turn signal switch”
(P. 2-45).

High Coolant Temp: See
Owner’s Manual

This warning appears when the tempera-
ture of the engine coolant is too high. Stop
the vehicle in a safe location as soon as
possible. Avoid quick starting or abrupt
acceleration. When the warning turns off,
the vehicle can be driven.

If the warning appears again soon after it
turns off, have the vehicle checked. It is rec-
ommended that you visit a NISSAN dealer
for this service.

Low Fuel

This warning appears when the fuel level in
the fuel tank is getting low. Refuel as soon
as it is convenient, preferably before the

fuel gauge reaches 0 (Empty).

There will be

a small reserve of fuel in the tank when
the fuel gauge needle reaches 0 (Empty).

Low Outside Temperature

This warning appears if the outside tem-
perature is below 37°F (3°C). The tempera-
ture can be changed to display in Celsius or
Fahrenheit. For additional information, see
“Settings” (P. 2-29).

Oil and Filter

This indicator appears when the customer
set distance comes for changing the engine
oil and filter. You can set or reset the distance
for checking or replacing these items. For
scheduled maintenance items and intervals,
see “Maintenance and schedules” (P. 9-2 ).

Other

This indicator appears when the customer
set distance is reached for checking or re-
placing maintenance items other than the
engine oil, oil filter and tires. Other mainte-
nance items can include such things as
air filter or tire rotation. The distance for
checking or replacing the items can be set
or reset.

Instruments and controls

2-37

Outside Temperature
Display

The outside temperature display appears
in the center region of the vehicle informa-
tion display.

Power turned off to save the battery

This message appears after the ignition
switch is automatically turned off. For addi-
tional information, see “Push-button igni-
tion switch positions” (P. 5-14).

Power will turn off to save the battery

This message appears in the vehicle infor-
mation display after a period of time if the
ignition switch is in the ON position and if
the vehicle is in P (Park). For additional infor-
mation, see “Push-button ignition switch
positions” (P. 5-14).

Push brake and start
switch to drive

This indicator appears when the shift lever
is in the P (Park) position and the vehicle
has not been started. Start the engine by
pushing the ignition switch with the brake
pedal depressed. You can start the engine
from any position of the ignition switch.

This message also appears when the ve-
hicle has been started using the Remote
Engine Start function (if so equipped). Push
the ignition switch with the brake pedal
depressed to place the ignition switch in
the ON position. For additional information,
see “Remote Engine Start” (P. 3-20).

Rear Door Alert is activated

When the system is enabled, this message
appears when the Rear Door Alert system
is active and can remind the driver to check
the back seat.
• Using the steering wheel switch, a driver

can select “Dismiss Message” to clear the
display for a period of time. If no selection
is made, this message automatically
turns off after a period of time.

• Using the steering wheel switch, a driver

can select “Disable Alert” to disable the
horn alert for the remainder of the current
trip.

WARNING

Selecting “Dismiss Message” during a
stop within a trip temporarily dismisses
the message for that stop without turn-
ing the system off. Alerts can be provided

for other stops during the trip. Selecting
“Disable Alert” turns off the Rear Door
Alert system for the remainder of a trip
and no audible alert will be provided.

NOTE:

This system is disabled until a driver en-
ables it using the vehicle information
display. For additional information, see
“How to use the vehicle information dis-
play” (P. 2-26).

For additional information, see “Rear Door
Alert” (P. 2-61).

Rear seat belt reminder

This rear seat belt reminder appears after
starting the engine.

If any of the rear passenger seat belts are
not fastened, the seat belt icon illuminates
in red to show which seat belt is not fas-
tened. When a rear passenger’s seat belt
has been securely fastened, the color of the
corresponding seat belt icon will change.
The warning will automatically turn off
after approximately 65 seconds.

A chime will sound and the rear seat belt
warning will appear if a rear passenger’s
seat belt is unfastened when the vehicle

2-38

Instruments and controls

speed exceeds 10 mph (15 km/h). The seat
belt icon illuminates in red until the corre-
sponding rear passenger’s seat belt is fas-
tened. The warning will automatically turn
off after approximately 65 seconds.

Release Parking Brake

This warning appears in the message area
of the vehicle information display when
the parking brake is set and the vehicle is
driven.

Reminder: Turn OFF
Headlights

This warning appears when the headlights
are left in the ON position when exiting the
vehicle. Place the headlight switch in the
OFF or AUTO position. For additional infor-
mation, see “Headlight and turn signal
switch” (P. 2-45).

Shift to Park

This warning appears when the ignition
switch is in the OFF position and the shift
lever is not in the P (Park) position. Also, a
chime sounds when the ignition switch is
in the OFF position.

If this warning appears, move the shift lever
to the P (Park) position and start the engine.

Shipping Mode On Push Storage Fuse

This warning may appear if the extended
storage switch is not pushed in. When this
warning appears, push in the extended
storage switch to turn off the warning. For
additional information, see “Extended stor-
age switch” (P. 2-62).

Steering lock release
malfunction indicator

This indicator appears when the steering
lock cannot be released.

If this indicator appears, push the ignition
switch while lightly turning the steering
wheel right and left.

Tire

This indicator appears when the customer
set distance is reached for replacing tires.
You can set or reset the distance for replac-
ing tires.

WARNING

The tire replacement indicator is not a
substitute for regular tire checks, includ-
ing tire pressure checks. For additional
information, see “Changing wheels and
tires” (P. 8-37). Many factors including
tire inflation, alignment, driving habits

and road conditions affect tire wear and
when tires should be replaced. Setting
the tire replacement indicator for a cer-
tain driving distance does not mean your
tires will last that long. Use the tire re-
placement indicator as a guide only and
always perform regular tire checks. Fail-
ure to perform regular tire checks, in-
cluding tire pressure checks could result
in tire failure. Serious vehicle damage
could occur and may lead to a collision,
which could result in serious personal in-
jury or death.

Tire Pressure Low - Add Air

This warning appears when the low tire
pressure warning light in the meter illumi-
nates and low tire pressure is detected. The
warning appears each time the ignition
switch is placed in the ON position as long
as the low tire pressure warning light re-
mains illuminated. If this warning appears,
stop the vehicle and adjust the tire pres-
sures of all four tires to the recommended
COLD tire pressure shown on the Tire and
Loading Information label. For additional
information, see “Low tire pressure warning
light” (P. 2-18) and “Tire Pressure Monitoring
System (TPMS)” (P. 5-5).

Instruments and controls

2-39

TPMS Error: See Owner’s Manual

This warning appears when there is an er-
ror with your TPMS. If this warning comes
on, have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Transmission Shift Position
Indicator

This indicator shows the transmission shift
position.

Automatic Emergency
Braking (AEB) emergency
warning indicator

This indicator appears along, with an au-
dible warning, when the system detects the
possibility of a forward collision.

For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian
Detection” (P. 5-83).

Blind Spot Warning (BSW)
indicator

This indicator shows when the BSW system
is engaged.

For additional information, see “Blind Spot
Warning (BSW)” (P. 5-33).

Cruise control indicator

This indicator shows the cruise control sys-
tem status.

For additional information, see “Cruise con-
trol” (P. 5-51).

Driver Attention Alert —
System Fault

This warning appears when the Intelligent
Driver Alertness (I-DA) system is not func-
tioning properly. For additional informa-
tion, see “Intelligent Driver Alertness (I-DA)”
(P. 5-111).

Driver Attention Alert -
Take a Break?

This alert appears when the system has
detected that the driver may be displaying
fatigue or a lack of attention.

Intelligent Cruise Control
(ICC) indicator

This indicator shows the Intelligent Cruise
Control (ICC) system status. The status is
shown by the color. For additional informa-
tion, see “Intelligent Cruise Control (ICC)”
(P. 5-53).

Lane Departure Warning
(LDW) indicator

This indicator shows when the LDW system
is engaged.

For additional information, see “Lane De-
parture Warning (LDW)” (P. 5-26).

Malfunction

This warning appears when one or more of
the following systems (if so equipped) is
not functioning properly:
• Automatic Emergency Braking (AEB) with

Pedestrian Detection

• Blind Spot Warning (BSW)
• Rear Cross Traffic Alert (RCTA)
• Intelligent Forward Collision Warning

(I-FCW)

If one or more of these warning appears,
have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Parking Sensor

This indicator appears when the sensor is
activated. For additional information, see
“Rear Sonar System (RSS)” (P. 5-122).

2-40

Instruments and controls

Parking Sensor Error: See Owner’s
Manual

This warning appears when there is an er-
ror with the system. For additional informa-
tion, see “Rear Sonar System (RSS)” (P. 5-122).

Rear Automatic Braking
(RAB) system indicator

This indicator appears to indicate the sta-
tus of the Rear Automatic Braking (RAB)
system. For additional information, see
“Rear Automatic Braking (RAB)” (P. 5-76).

System Fault

This warning appears if there is a malfunc-
tion in the Rear Automatic Braking (RAB)
system. For additional information, see
“Rear Automatic Braking (RAB)” (P. 5-76).

Unavailable: Front Radar Obstruction

This warning appears when there is a radar
obstruction detected. For additional in-
formation,

see

“Automatic

Emergency

Braking (AEB) with Pedestrian Detection”
(P. 5-83) or “Intelligent Cruise Control (ICC)”
(P. 5-53), or “Intelligent Forward Collision
Warning (I-FCW)” (P. 5-96).

Unavailable: High Cabin Temperature

This message appears when the camera
detects an interior temperature of more
than approximately 104°F (40°C). For addi-
tional information, see “Lane Departure
Warning (LDW)” (P. 5-26).

Unavailable: Side Radar Obstruction

This message appears when the Blind
Spot Warning (BSW) or Rear Cross Traffic
Alert (RCTA) systems become unavailable
because a radar blockage is detected.
For additional information, see “Blind Spot
Warning (BSW)” (P. 5-33) or “Rear Cross Traf-
fic Alert (RCTA)” (P. 5-43).

Vehicle ahead detection
indicator

This indicator appears when the Auto-
matic Emergency Braking (AEB) with Pe-
destrian Detection system is engaged and
has detected a vehicle.

For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian
Detection ” (P. 5-83) or “Intelligent Forward
Collision Warning (I-FCW)” (P. 5-96).

Your vehicle has one type of security system:
• NISSAN Vehicle Immobilizer System

NISSAN VEHICLE IMMOBILIZER
SYSTEM

The NISSAN Vehicle Immobilizer System
will not allow the engine to start without
the use of a registered key.

LIC2930

SECURITY SYSTEM

Instruments and controls

2-41

If the engine fails to start using a regis-
tered key (for example, when interference is
caused by another registered key, an auto-
mated toll road device or automatic pay-
ment device on the key ring), restart the
engine using the following procedures:

1. Leave the ignition switch in the ON posi-

tion for approximately 5 seconds.

2. Place the ignition switch in the OFF or

LOCK position and wait approximately
10 seconds.

3. Repeat steps 1 and 2.

4. Restart the engine while holding the de-

vice (which may have caused the inter-
ference) separate from the registered
key.

If the no start condition reoccurs, NISSAN
recommends placing the registered key on
a separate key ring to avoid interference
from other devices.

Never leave these keys in the vehicle.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any inter-
ference received, including interference
that may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's author-
ity to operate the equipment.

For Canada:

This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause
undesired operation of the device.

Security indicator light

The security indicator light blinks whenever
the ignition switch is placed in the OFF or
LOCK position.

This function indicates the NISSAN Vehicle
Immobilizer System is operational.

If the NISSAN Vehicle Immobilizer System is
malfunctioning, the light will remain on
while the ignition switch is placed in the ON
position.

LIC0474

2-42

Instruments and controls

If the light still remains on and/or the
engine will not start, seek service for
the NISSAN Vehicle Immobilizer System
service as soon as possible. Please bring
all registered keys that you have. It is
recommended that you visit a NISSAN
dealer for this service.

SWITCH OPERATION

WARNING

In freezing temperatures the washer
solution may freeze on the windshield
and obscure your vision which may
lead to an accident. Warm the wind-
shield with the defroster before you
wash the windshield.

CAUTION

•

Do not operate the washer continu-
ously for more than 30 seconds.

•

Do not operate the washer if the
windshield-washer fluid reservoir is
empty.

•

Do not fill the windshield-washer
fluid

reservoir

with

windshield-

washer fluid concentrates at full
strength.

Some

methyl

alcohol

based windshield-washer fluid con-
centrates may permanently stain the
grille

spilled

while

filling

the

windshield-washer fluid reservoir.

•

Pre-mix windshield-washer fluid con-
centrates with water to the manufac-
turer's recommended levels before
pouring the fluid into the windshield-
washer fluid reservoir. Do not use
the windshield-washer fluid reservoir
to mix the windshield-washer fluid
concentrate and water.

NOTE:

If the windshield wiper operation is in-
terrupted by snow or ice, the wiper may
stop moving to protect its motor. If this
occurs, turn the wiper switch to the OFF
position and remove the snow or ice that
is on and around the wiper arms. In ap-
proximately 1 minute, turn the switch on
again to operate the wiper.

LIC4182

WIPER AND WASHER SWITCH

Instruments and controls

2-43

The windshield wiper and washer operates
when the ignition switch is placed in the ON
position.

Push the lever down to operate the wiper
at the following speed:

䊊

Intermittent — intermittent operation
can be adjusted by turning the knob in
the

direction (faster) or

direction

(slower).

䊊

Low — continuous low speed operation

䊊

High — continuous high speed operation

Push the lever up

to have one sweep

operation (MIST) of the wiper.

Pull the lever toward you

to operate the

washer. The wiper will also operate several
times.

To defrost the rear window glass, start the
engine and push the rear window defroster
switch on. The rear window defroster indi-
cator light on the switch comes on. Push
the switch again to turn the defroster off.

defrost

the

outside

mirrors

(if

equipped), start the engine and push the
outside mirror defroster switch on. The out-
side mirror defroster indicator light on the
switch comes on. Push the switch again to
turn the defroster off.

The rear window/outside mirror defroster
(if so equipped) automatically turns off
after approximately 15 minutes.

NOTE:

Use defroster and/or outside mirror de-
froster when engine is running to avoid
discharging the battery.

CAUTION

When cleaning the inner side of the rear
window, be careful not to scratch or
damage the rear window defroster.

LIC3570

Type A (if so equipped)

LIC3600

Type B (if so equipped)

REAR WINDOW AND OUTSIDE
MIRROR (if so equipped)
DEFROSTER SWITCH

2-44

Instruments and controls

HEADLIGHT CONTROL SWITCH

Lighting

䊊

Rotate the switch to the

position,

and the front parking, tail, license plate,
and instrument panel lights will come
on. The

will illuminate in the meter.

䊊

Rotate the switch to the

position,

and the headlights will come on and all
the other lights remain on.

CAUTION

Use the headlights with the engine run-
ning to avoid discharging the vehicle
battery.

Autolight system

The autolight system allows the headlights
to turn on and off automatically. The auto-
light system can:
• Turn on the headlights, front parking, tail,

license plate and instrument panel lights
automatically when it is dark.

• Turn off all the lights when it is light.
• Keep all the lights on for a period of time

after you place the ignition switch in the
OFF position and all doors are closed.

LIC2635

Type A (if so equipped)

LIC4237

Type B (if so equipped)

LIC5090

HEADLIGHT AND TURN SIGNAL
SWITCH

Instruments and controls

2-45

NOTE:
Autolight activation sensitivity and the
time delay for autolight shutoff can be
adjusted. For additional information, see
“Vehicle information display” (P. 2-25).

To turn on the autolight system:

For USA:

Turn the headlight switch to the

AUTO position

For CAN:

Turn the headlight switch to the

AUTO

position.

2. Place the ignition switch in the ON position.

3. The

autolight

system

automatically

turns the headlights on and off.

Initially, if the ignition switch is placed in the
OFF position and a door is opened and left
open, the headlights remain on for a period
of time. If another door is opened while the
headlights are on, then the timer is reset.

To turn the autolight system off:

For USA:

Turn the switch to the OFF,

position.

For CAN:

Turn the switch to the

position.

The Intelligent Auto Headlight system can
turn on the headlights automatically when
it is dark and turn off the headlights when it
is light.

If the ignition switch is placed in the ON
position when the parking brake is applied,
the headlights remain off.

The headlights will turn on automatically at
twilight (if so equipped) or in rainy weather
(when the windshield wiper is operated
continuously).

If the ignition switch is pushed to the OFF
position and one of the doors is opened
and this condition is continued, the head-
lights remain on for 5 minutes.

Be sure you do not put anything on top
of the autolight sensor located in the
top side

of the instrument panel. The

autolight sensor controls the autolight;
if it is covered, the autolight sensor re-
acts as if it is dark out and the headlights
will illuminate. If this occurs while parked
with the engine off and the ignition switch
placed in the ON position, your vehicle's
battery could become discharged.

LIC4223

2-46

Instruments and controls

Headlight beam select

䊊

To select the high beam function, push
the lever forward. The high beam lights
come on and the

light illuminates

in the meter.

䊊

Pull the lever back to select the low
beam.

䊊

Pulling and releasing the lever flashes
the headlight high beams on and off.

High Beam Assist

The High Beam Assist system will operate
when the vehicle is driven at speeds of ap-
proximately 18 mph (30 km/h) and above.
If an oncoming vehicle or leading vehicle
appears in front of your vehicle when the
headlight high beam is on, the head-
light will be switched to the low beam
automatically.

WARNING

•

The High Beam Assist system is a
convenience but it is not a substitute
for safe driving operation. The driver
should remain alert at all times,
ensure safe driving practices and
switch the high beams and low beam
manually when necessary.

•

The high beam or low beam may not
switch automatically under the fol-
lowing conditions. Switch the high
beam and low beam manually.

–

During bad weather (rain, fog, snow,
wind, etc.).

–

When a light source similar to a
headlight or tail light is in the vi-
cinity of the vehicle.

–

When the headlights of the on-
coming vehicle or the leading ve-
hicle are turned off, when the color
of the light is affected due to for-
eign materials on the lights, or
when the light beam is out of
position.

–

When there is a sudden, continu-
ous change in brightness.

–

When driving on a road that
passes over rolling hills, or a road
that has level differences.

–

When driving on a road with many
curves.

–

When a sign or mirror-like surface
is reflecting intense light towards
the front of the vehicle.

–

When the container, etc. being
towed by a leading vehicle is re-
flecting intense light.

–

When a headlight on your vehicle
is damaged or dirty.

–

When the vehicle is leaning at an
angle due to a punctured tire,
being towed, etc.

LIC5092

Instruments and controls

2-47

•

The timing of switching the low
beam and high beam may change
under the following situations.

–

The brightness of the headlights
of the oncoming vehicle or leading
vehicle.

–

The movement and direction of
the oncoming vehicle and the
leading vehicle.

–

When only one light on the on-
coming vehicle or the leading ve-
hicle is illuminated.

–

When the oncoming vehicle or the
leading vehicle is a two-wheeled
vehicle.

–

Road conditions (incline, curve,
the road surface, etc.).

–

The number of passengers and
the amount of luggage.

High Beam Assist operation

To activate the High Beam Assist system,
turn the headlight switch to the AUTO po-
sition

and push the lever forward

(high beam position). The

High Beam

Assist indicator light in the meter will illumi-
nate while the headlights are turned on.

If the High Beam Assist indicator light does
not illuminate in the above condition, it may
indicate that the system is not functioning
properly. Have the system checked, it is
recommended that you visit a NISSAN
dealer for this service.

When the vehicle speed lowers to less than
approximately 12 mph (20 km/h), the head-
light uses the low beam.

To turn off the High Beam Assist system,
turn the headlight switch to the

posi-

tion or select the low beam position by
placing the lever in the neutral position.

LIC5093

2-48

Instruments and controls

Ambient image sensor maintenance

The ambient image sensor

for the High

Beam Assist system is located in front of
the inside mirror. To maintain the proper
operation of the high beam assist system
and prevent a system malfunction, be sure
to observe the following:
• Always keep the windshield clean.
• Do not attach a sticker (including trans-

parent material) or install an accessory
near the ambient image sensor.

• Do not strike or damage the areas around

the ambient image sensor. Do not touch
the sensor lens that is located on the am-
bient image sensor.

If the ambient image sensor is damaged
due to an accident, it is recommended that
you visit a NISSAN dealer.

Battery saver system

If the ignition switch is placed in the OFF
position while the headlight switch is in the

position, the headlights will

turn off after a period of time.

NOTE:

The Battery Saver system may be dis-
abled. For additional information, see
“Vehicle information display” (P. 2-25).

CAUTION

Even though the battery saver feature
automatically turns off the headlights
after a period of time, you should turn
the headlight switch to the AUTO or OFF
position when the engine is not run-
ning to avoid discharging the vehicle
battery.

DAYTIME RUNNING LIGHTS (DRL)
SYSTEM (Type A) (if so equipped)

The Daytime Running Lights (DRL) auto-
matically illuminate when the engine is
started with the parking brake released.
The DRL operate with the headlight switch
in the AUTO or OFF position. Turn the head-
light switch to the

position for full

illumination when driving at night. (The DRL
will turn off.)

If the parking brake is applied before the
engine is started, the DRL do not illuminate.
The DRL illuminate once the parking brake
is released. The DRL will remain on until the
ignition switch is placed in the OFF position.

It is necessary at dusk to turn the headlight
switch ON for interior controls and switches
to illuminate, as those remain OFF while the
switch is in the AUTO or OFF position.

WARNING

When the DRL system is active, tail lights
on your vehicle are not on. It is necessary
at dusk to turn on your headlights. Fail-
ure to do so could cause an accident in-
juring yourself and others.

LSD4102

Instruments and controls

2-49

LED DAYTIME RUNNING LIGHTS
(DRL) SYSTEM (Type B) (if so
equipped)

The LED DRL automatically illuminate at
100% intensity when the engine is started
and the parking brake released. The LED
Daytime Running Lights (DRL) operate with
the headlight switch in the AUTO or OFF
position. When you turn the headlight
switch to the

position for full illumina-

tion, the LED lights switch from LED DRL to
the park function.

If the parking brake is applied before the
engine is started, the LED DRL do not illumi-
nate. The LED DRL illuminate when the
parking brake is released. The LED DRL will
remain on until the ignition switch is placed
in the OFF position.

It is necessary at dusk to turn the headlight
switch ON for interior controls and switches
to illuminate, as those remain OFF while the
switch is in the AUTO or OFF position.

WARNING

When the LED DRL system is active, tail
lights on your vehicle are not on. It is
necessary at dusk to turn on your head-
lights. Failure to do so could cause an
accident injuring yourself and others.

INSTRUMENT BRIGHTNESS
CONTROL

Turn the control knob

to adjust the

brightness of instrument panel lights.

LIC4150

Type A (if so equipped)

LIC4151

Type B (if so equipped)

2-50

Instruments and controls

TURN SIGNAL SWITCH

Turn signal

䊊

Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signal cancels automati-
cally.

Lane change signal

䊊

Move the lever up or down until the turn
signal begins to flash, but the lever
does not latch, to signal a lane change.
Hold the lever until the lane change is
completed.

Move the lever up or down until the turn
signal begins to flash, but the lever does
not latch, and release the lever. The turn
signal will automatically flash three times.

Choose the appropriate method to signal
a lane change based on road and traffic
conditions.

NOTE:

The 3 flash pass feature may be disabled.
For additional information, see “Vehicle
information display” (P. 2-25).

FOG LIGHT SWITCH (if so
equipped)

To turn the fog lights on, turn the headlight
switch to the

position, then

turn the fog light switch to the
position.

To turn the fog lights on with the headlight
switch in the AUTO position, the headlights
must be on, then turn the fog light switch to
the

position.

To turn the fog lights off, turn the fog light
switch to the OFF position.

LIC5094

LIC5095

Instruments and controls

2-51

To sound the horn, push near the horn icon
on the steering wheel.

WARNING

Do not disassemble the horn. Doing so
could affect proper operation of the
supplemental front air bag system. Tam-
pering with the supplemental front air
bag system may result in serious per-
sonal injury.

WARNING

Do not use or allow occupants to use
the seat heater if you or the occupants
cannot monitor elevated seat tem-
peratures or have an inability to feel
pain in body parts that contact the
seat. Use of the seat heater by such
people could result in serious injury.

CAUTION

•

The battery could run down if the
seat heater is operated while the
engine is not running.

•

Do not use the seat heater for ex-
tended periods or when no one is us-
ing the seat.

•

Do not put anything on the seat which
insulates heat, such as a blanket,
cushion, seat cover, etc. Otherwise, the
seat may become overheated.

•

Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the heater.

•

Any liquid spilled on the heated seat
should be removed immediately with
a dry cloth.

•

When cleaning the seat, never use
gasoline, benzine, thinner, or any simi-
lar materials.

•

If any malfunctions are found or the
heated seat does not operate, turn
the switch off and have the system
checked. It is recommended that you
visit a NISSAN dealer for this service.

LIC3568

LIC3973

HORN

HEATED SEAT SWITCHES (if so
equipped)

2-52

Instruments and controls

The front seats are warmed by built-in
heaters.

1. Place the ignition switch in the ON

position.

2. Push the switch once for the high (2 in-

dicators illuminated) setting. Push the
switch again for the low (1 indicator illu-
minated) setting.

The heater is controlled by a thermostat,
automatically turning the heater on and
off. The indicator light(s) will remain on
as long as the switch is on.

3. Push the switch again to turn it off (no

indicators illuminated).

4. When the seat is warmed or before you

leave the vehicle, be sure to push the
switch to turn it off.

The Lane Departure Warning (LDW) switch
is used to turn on and off the LDW system.
When the LDW switch is pushed, the LDW
system will turn on and the LDW indicator
light on the switch will illuminate. When the
LDW switch is pushed again, the LDW sys-
tem will turn off and the LDW indicator light
will turn off.

The LDW system warns the driver with an
indicator and a chime that the vehicle is
beginning to leave the driving lane. For ad-
ditional information, see “Lane Departure
Warning (LDW) ” (P. 5-26).

The Automatic Emergency Braking (AEB)
with Pedestrian Detection system and In-
telligent Forward Collision Warning (I-FCW)
system may be linked with the LDW sys-
tem. For additional information, see “Auto-
matic Emergency Braking (AEB) with Pe-
destrian Detection” (P. 5-83) or “Intelligent
Forward Collision Warning (I-FCW)” (P. 5-96).

LIC5039

LANE DEPARTURE WARNING (LDW)
SWITCH (if so equipped)

Instruments and controls

2-53

Nissan Versa (2024 year). Manual in english - page 4