Nissan Versa (2024 year). Manual in english

–

Inspect the lower anchors by insert-
ing your fingers into the lower an-
chor area. Feel to make sure there
are no obstructions over the an-
chors such as seat belt webbing or
seat cushion material. The child re-
straint will not be secured properly if
the lower anchors are obstructed.

Child restraint anchorages are de-
signed to withstand only those loads
imposed by correctly fitted child re-
straints. Under no circumstances are
they to be used to attach adult seat
belts, or other items or equipment to
the vehicle. Doing so could damage the
child restraint anchorages. The child
restraint will not be properly installed
using the damaged anchorage, and a
child could be seriously injured or killed
in a collision.

LATCH lower anchor location

The LATCH lower anchors are located as
shown. A label is attached to the seatback to
help you locate the LATCH lower anchors.

LATCH in the center rear seating
position

There are no LATCH anchors dedicated to
the center rear seating position. However,
the inboard LATCH anchors belonging to
the two outboard seating positions (indi-
cated by the arrows) can be used together
to secure a CRS in the center rear seating
position. These anchors are separated by a
distance

of 14 in (377 mm). Before at-

tempting to secure a CRS in this seating
position, ensure that the CRS manufactur-
er’s instructions permit the use of LATCH
anchors with the spacing indicated above.

LRS3036

LATCH lower anchor location

LRS3342

1-22

Safety-Seats, seat belts and supplemental restraint system

(These are sometimes referred to as
“shared anchors” or “borrowed anchors.”)

CRS with rigid lower attachments cannot
be installed in the center seat. This type of
CRS should only be installed in the out-
board seating positions.

WARNING

Never attach two CRS attachments to
the same LATCH anchor. This may over-
load the anchor in a collision, which
could increase the risk of the occu-
pant’s serious injury or death.

When installing the CRS in the center
rear seating position with the inboard
LATCH anchors, be careful to ensure any
occupant or CRS in the outboard seat-
ing positions is properly restrained us-
ing the vehicle seat belt and there is no
interference with the center CRS instal-
lation. If the outboard occupants can-
not be properly restrained, consider us-
ing the vehicle seat belt to restrain the
CRS in the center seating position, or
moving the CRS to another position
instead.

Installing child restraint LATCH
lower anchor attachments

LATCH compatible child restraints include
two rigid or webbing-mounted attach-
ments that can be connected to two an-
chors located at certain seating positions
in your vehicle. With this system, you do not
have to use a vehicle seat belt to secure the
child restraint. Check your child restraint for
a label stating that it is compatible with
LATCH. This information may also be in the
instructions provided by the child restraint
manufacturer.

When installing a child restraint, carefully
read and follow the instructions in this
manual and those supplied with the child
restraint.

LRS0661

LATCH webbing-mounted attachment

LRS0662

LATCH rigid-mounted attachment

Safety-Seats, seat belts and supplemental restraint system

1-23

Top tether anchor point locations

Anchor points are located on the rear par-
cel shelf

WARNING

child restraint anchorages. The child
restraint will not be properly installed
using the damaged anchorage, and a
child could be seriously injured or killed
in a collision.

REAR-FACING CHILD RESTRAINT
INSTALLATION USING LATCH

For additional information, see all Warnings
and Cautions in “Child safety” (P. 1-16) and
“Child restraints” (P. 1-19) before installing a
child restraint.

Do not use the lower anchors if the com-
bined weight of the child and the child re-
straint exceeds 65 lbs. (29.5 kg). If the com-
bined weight of the child and the child
restraint is greater than 65 lbs. (29.5 kg), use
the vehicle's seat belt (not the lower an-
chors) to install the child restraint. Be sure
to follow the child restraint manufacturer's
instructions for installation.

Follow these steps to install a rear-facing
child restraint using the LATCH system:

1. Position the child restraint on the seat.

Always follow the child restraint manu-
facturer's instructions.

2. Secure the child restraint anchor at-

tachments to the LATCH lower anchors.
Check to make sure the LATCH attach-
ment is properly attached to the lower
anchors.

LRS3313

LRS2997

Rear-facing webbing-mounted – step 2

1-24

Safety-Seats, seat belts and supplemental restraint system

3. For child restraints that are equipped

with webbing-mounted attachments,
remove any additional slack from the
anchor attachments. Press downward
and rearward firmly in the center of the
child restraint with your hand to com-
press the vehicle seat cushion and seat-
back while tightening the webbing of
the anchor attachments.

4. After attaching the child restraint, test it

before you place the child in it. Push it
from side to side while holding the child
restraint near the LATCH attachment
path. The child restraint should not
move more than 1 inch (25 mm), from
side to side. Try to tug it forward and
check to see if the LATCH attachment
holds the restraint in place. If the re-
straint is not secure, tighten the LATCH
attachment as necessary, or put the re-
straint in another seat and test it again.

LRS2996

Rear-facing rigid-mounted – step 2

LRS0673

Rear-facing – step 3

LRS0674

Rear-facing – step 4

Safety-Seats, seat belts and supplemental restraint system

1-25

You may need to try a different child
restraint or try installing by using the
vehicle seat belt (if applicable). Not all
child restraints fit in all types of vehicles.

5. Check to make sure the child restraint is

properly secured prior to each use. If the
child restraint is loose, repeat steps 1
through 4.

REAR-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT
BELTS

WARNING

For additional information, see all Warnings
and Cautions in “Child safety” (P. 1-16) and
“Child restraints” (P. 1-19) before installing a
child restraint.

Follow these steps to install a rear-facing
child restraint using the vehicle seat belts in
the rear seats:

Child restraints for infants must be
used in the rear-facing direction and
therefore must not be used in the front
seat.

Position the child restraint on the

seat. Always follow the child restraint
manufacturer’s instructions.

WRS0256

Rear-facing – step 1

1-26

Safety-Seats, seat belts and supplemental restraint system

2. Route the seat belt tongue through the

child restraint and insert it into the
buckle until you hear and feel the latch
engage. Be sure to follow the child re-
straint manufacturer’s instructions for
belt routing.

3. Pull the shoulder belt until the belt is fully

extended. At this time, the seat belt re-
tractor is in the ALR mode (child restraint
mode). It reverts to the ELR mode when
the seat belt is fully retracted.

4. Allow the seat belt to retract. Pull up on

the shoulder belt to remove any slack in
the belt.

WRS0761

Rear-facing – step 2

LRS2395

Rear-facing – step 3

LRS2396

Rear-facing – step 4

Safety-Seats, seat belts and supplemental restraint system

1-27

5. Remove any additional slack from the

seat belt; press downward and rearward
firmly in the center of the child restraint
to compress the vehicle seat cushion
and seatback while pulling up on the
seat belt.

6. After attaching the child restraint, test it

before you place the child in it. Push it
from side to side while holding the child
restraint near the seat belt path. The
child restraint should not move more
than 1 inch (25 mm), from side to side. Try
to tug it forward and check to see if the
belt holds the restraint in place. If the
restraint is not secure, tighten the seat
belt as necessary, or put the restraint in
another seat and test it again. You may
need to try a different child restraint.
Not all child restraints fit in all types of
vehicles.

7. Check to make sure that the child re-

straint is properly secured prior to each
use. If the seat belt is not locked, repeat
steps 3 through 6.

After the child restraint is removed and the
seat belt fully retracted, the ALR mode
(child restraint mode) is canceled.

FORWARD-FACING CHILD
RESTRAINT INSTALLATION USING
LATCH

For additional information, see all Warnings
and Cautions in “Child safety” (P. 1-16) and
“Child restraints” (P. 1-19) before installing a
child restraint.

Do not use the lower anchors if the com-
bined weight of the child and the child re-
straint exceeds 65 lbs. (29.5 kg). If the com-
bined weight of the child and the child
restraint is greater than 65 lbs. (29.5 kg), use
the vehicle’s seat belt (not the lower an-
chors) to install the child restraint. Be sure
to follow the child restraint manufacturer’s
instructions for installation.

Follow these steps to install a forward-facing
child restraint using the LATCH system:

1. Position the child restraint on the seat.

Always follow the child restraint manu-
facturer's instructions.

WRS0762

Rear-facing – step 5

LRS2397

Rear-facing – step 6

1-28

Safety-Seats, seat belts and supplemental restraint system

2. Secure the child restraint anchor at-

tachments to the LATCH lower anchors.
Check to make sure the LATCH attach-
ment is properly attached to the lower
anchors.

If the child restraint is equipped with a
top tether strap, route the top tether
strap and secure the tether strap to the
tether anchor point. For additional infor-
mation, see “Installing top tether strap”
(P. 1-31).

Do not install child restraints that require
the use of a top tether strap in seating
positions that do not have a top tether
anchor.

3. The back of the child restraint should be

secured against the vehicle seatback.

If necessary, adjust or remove the head
restraint/headrest to obtain the correct
child restraint fit. If the head restraint/
headrest is removed, store it in a secure
place.

Be sure to reinstall the head

restraint/headrest when the child re-
straint is removed.

For additional infor-

mation, see “Head restraints/headrests”
(P. 1-5).

If the seating position does not have an
adjustable head restraint/headrest and
it is interfering with the proper child re-
straint fit, try another seating position or
a different child restraint.

LRS2995

Forward-facing webbing-mounted –

step 2

LRS2994

Forward-facing rigid-mounted – step 2

Safety-Seats, seat belts and supplemental restraint system

1-29

4. For child restraints that are equipped

with webbing-mounted attachments,
remove any additional slack from the
anchor attachments. Press downward
and rearward firmly in the center of the
child restraint with your knee to com-
press the vehicle seat cushion and seat-
back while tightening the webbing of
the anchor attachments.

5. Tighten the tether strap according to

the manufacturer's instructions to re-
move any slack.

6. After attaching the child restraint, test it

You may need to try a different child
restraint. Not all child restraints fit in all
types of vehicles.

7. Check to make sure the child restraint is

properly secured prior to each use. If the
child restraint is loose, repeat steps 1
through 6.

LRS0671

Forward-facing – step 4

WRS0697

Forward-facing – step 6

1-30

Safety-Seats, seat belts and supplemental restraint system

Installing top tether strap

䊊

Top tether strap

䊊

Anchor point

The child restraint top tether strap must be
used when installing the child restraint with
the LATCH lower anchor attachments.

First, secure the child restraint with the
LATCH lower anchors.

Rear bench seat

OUTBOARD AND CENTER SEATING POSI-
TIONS

1. Position the top tether strap

over the

seatback.

2. Secure the tether strap to the tether an-

chor point

as shown.

3. Tighten the tether strap according to

the manufacturer’s instructions to re-
move any slack.

If you have any questions when installing
a top tether strap, it is recommended that
you visit a NISSAN dealer for this service.

WARNING

FORWARD-FACING CHILD
RESTRAINT INSTALLATION USING
THE SEAT BELTS

WARNING

The three-point seat belt with Auto-
matic Locking Retractor (ALR) must be
used when installing a child restraint.
Failure to use the ALR mode will result
in the child restraint not being properly
secured. The restraint could tip over or
be loose and cause injury to a child in a
sudden stop or collision. Also, it can
change the operation of the front pas-
senger air bag. For additional informa-
tion, see “Front passenger air bag and
status light” (P. 1-51).

LRS3310

Rear bench seat

Safety-Seats, seat belts and supplemental restraint system

1-31

For additional information, see all Warnings
and Cautions in “Child safety” (P. 1-16) and
“Child restraints” (P. 1-19) before installing a
child restraint.

Follow these steps to install a forward-
facing child restraint using the vehicle seat
belt in the rear seats or in the front passen-
ger seat:

If you must install a child restraint in
the front seat, it should be placed in a
forward-facing direction only. Move
the seat to the rearmost position.
Child restraints for infants must be
used in the rear-facing direction and,
therefore, must not be used in the
front seat.

2. Position the child restraint on the seat.

Always follow the child restraint manu-
facturer’s instructions.

The back of the child restraint should be
secured against the vehicle seatback.

If necessary, adjust or remove the head
restraint/headrest to obtain the correct
child restraint fit. If the head restraint/
headrest is removed, store it in a secure
place.

Be sure to reinstall the head

restraint/headrest when the child re-
straint is removed.

For additional infor-

mation, see “Head restraints/headrests”
(P. 1-5). for head restraint/headrest adjust-
ment, removal and installation informa-
tion.

If the seating position does not have an
adjustable head restraint/headrest and
it is interfering with the proper child re-
straint fit, try another seating position or
a different child restraint.

WRS0699

Forward-facing (front passenger seat) –

step 1

1-32

Safety-Seats, seat belts and supplemental restraint system

3. Route the seat belt tongue through the

child restraint and insert it into the
buckle until you hear and feel the latch
engage. Be sure to follow the child re-
straint manufacturer’s instructions for
belt routing.

If the child restraint is equipped with a
top tether strap, route the top tether
strap and secure the tether strap to the
tether anchor point (rear seat installa-
tion only). For additional information, see
“Installing top tether strap” (P. 1-35 ).

Do not install child restraints that require
the use of a top tether strap in seating
positions that do not have a top tether
anchor.

4. Pull the shoulder belt until the belt is fully

extended. At this time, the seat belt re-
tractor is in the ALR mode (child restraint
mode). It reverts to ELR mode when the
seat belt is fully retracted.

WRS0680

Forward-facing – step 3

LRS0667

Forward-facing – step 4

Safety-Seats, seat belts and supplemental restraint system

1-33

5. Allow the seat belt to retract. Pull up on

the shoulder belt to remove any slack in
the belt.

6. Remove any additional slack from the

seat belt; press downward and rear-
ward firmly in the center of the child re-
straint with your knee to compress the
vehicle seat cushion and seatback while
pulling up on the seat belt.

7. Tighten the tether strap according to the

manufacturer's instructions to remove
any slack.

8. After attaching the child restraint, test it

LRS0668

Forward-facing – step 5

WRS0681

Forward-facing – step 6

WRS0698

Forward-facing – step 8

1-34

Safety-Seats, seat belts and supplemental restraint system

9. Check to make sure the child restraint is

properly secured prior to each use. If the
seat belt is not locked, repeat steps 2
through 8.

10. If the child restraint is installed in the

front passenger seat, place the ignition
switch in the ON position. The front
passenger air bag status light
should illuminate. If this light is not illu-
minated, see "Front passenger air bag
and status light" (P. 1-51).

Move the child

restraint to another seating position.

Have the system checked. It is recom-
mended that you visit a NISSAN dealer
for this service.

After the child restraint is removed and the
seat belt is fully retracted, the ALR mode
(child restraint mode) is canceled.

Installing top tether strap

䊊

Top tether strap

䊊

Anchor point

The child restraint top tether strap must be
used when installing the child restraint with
seat belts.

First, secure the child restraint with the seat
belt.

LRS3091

Forward-facing – step 10

LRS3310

Rear bench seat

Safety-Seats, seat belts and supplemental restraint system

1-35

Rear bench seat

OUTBOARD AND CENTER SEATING POSI-
TIONS

1. Position the top tether strap

over the

seatback.

2. Secure the tether strap to the tether an-

chor point

as shown.

3. Tighten the tether strap according to

the manufacturer’s instructions to re-
move any slack.

If you have any questions when installing
a top tether strap, it is recommended that
you visit a NISSAN dealer for this service.

WARNING

BOOSTER SEATS

For additional information on installing a
booster seat in your vehicle, follow the in-
structions outlined in this section.

Precautions on booster seats

WARNING

If a booster seat and seat belt are not
used properly, the risk of a child being
injured or killed in a sudden stop or col-
lision greatly increases:

–

Make sure the shoulder portion of
the belt is away from the child's face
and neck and the lap portion of the
belt does not cross the stomach.

–

Make sure the shoulder belt is not
behind the child or under the child's
arm.

–

A booster seat must only be installed
in a seating position that has a lap/
shoulder belt.

LRS2479

A. Low back booster seat

B. High back booster seat

1-36

Safety-Seats, seat belts and supplemental restraint system

Booster seats of various sizes are offered
by several manufacturers. When selecting
any booster seat, keep the following points
in mind:
• Choose only a booster seat with a label

certifying that it complies with Federal
Motor Vehicle Safety Standard 213 or Ca-
nadian Motor Vehicle Safety Standard 213.

• Check the booster seat in your vehicle to

be sure it is compatible with the vehicle’s
seat and seat belt system.

• Make sure the child’s head will be properly

supported by the booster seat or vehicle
seat. The seatback must be at or above
the center of the child’s ears. For example,
if a low back booster seat is chosen, the
vehicle seatback must be at or above the
center of the child’s ears. If the seatback is
lower than the center of the child’s ears, a
high back booster seat should be used.

• If the booster seat is compatible with

your vehicle, place the child in the booster
seat and check the various adjustments
to be sure the booster seat is compatible
with the child. Always follow all recom-
mended procedures.

All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved
child restraint at all times while the ve-
hicle is being operated.

The instructions in this section apply to
booster seat installation in the rear seats
or the front passenger seat.

LRS0453

LRS0464

Safety-Seats, seat belts and supplemental restraint system

1-37

Booster seat installation

WARNING

To avoid injury to child, do not use the
lap/shoulder belt in the Automatic
Locking Retractor (ALR) mode when us-
ing a booster seat with the seat belts.

For additional information, see all Warnings
and Cautions in “Child safety” (P. 1-16) “Child
restraints” (P. 1-19) and “Booster seats”
(P. 1-36) before installing a child restraint.

Follow these steps to install a booster seat in
the rear seat or in the front passenger seat:

If you must install a booster seat in the
front seat, move the seat to the rear-
most position.

2. Position the booster seat on the seat.

Only place it in a front-facing direction.
Always follow the booster seat manu-
facturer’s instructions.

WRS0699

LRS0454

Front passenger position

1-38

Safety-Seats, seat belts and supplemental restraint system

3. The booster seat should be positioned

on the vehicle seat so that it is stable.

If necessary, adjust or remove the head
restraint/headrest to obtain the correct
booster seat fit. If the head restraint/
headrest is removed, store it in a secure
place.

Be sure to reinstall the head

restraint/headrest when the booster
seat is removed.

For additional infor-

mation, see “Head restraints/headrests”
(P. 1-5).

If the seating position does not have an
adjustable head restraint/headrest and
it is interfering with the proper booster
seat fit, try another seating position or a
different booster seat.

4. Position the lap portion of the seat belt

low and snug on the child’s hips. Be sure
to follow the booster seat manufactur-
er’s instructions for adjusting the seat
belt routing.

5. Pull the shoulder belt portion of the seat

belt toward the retractor to take up ex-
tra slack. Be sure the shoulder belt is
positioned across the top, middle por-
tion of the child’s shoulder. Be sure to
follow the booster seat manufacturer’s
instructions for adjusting the seat belt
routing.

6. Follow the warnings, cautions and in-

structions for properly fastening a seat
belt shown in “Three-point type seat belt
with retractor” (P. 1-13).

LRS0451

Rear center position

LRS0452

Rear outboard position

Safety-Seats, seat belts and supplemental restraint system

1-39

7. If the booster seat is installed in the front

passenger seat, place the ignition switch
in the ON position. The front passenger
air bag status light

may or may not

illuminate, depending on the size of the
child and the type of booster seat being
used. For additional information, see
"Front passenger air bag and status light"
(P. 1-51).

PRECAUTIONS ON SRS

This SRS section contains important infor-
mation concerning the following systems:
• Driver and front passenger supplemental

front-impact air bag (NISSAN Advanced
Air Bag System)

• Front seat-mounted side-impact supple-

mental air bag

• Rear outboard seat-mounted side-impact

supplemental air bag

• Roof-mounted curtain side-impact and

rollover supplemental air bag

• Driver and front passenger supplemental

knee air bag

• Seat belt with pretensioner(s) (front and

rear seats)

Supplemental front-impact air bag system

The NISSAN Advanced Air Bag System can
help cushion the impact force to the head
and chest of the driver and front passenger
in certain frontal collisions.

Front seat-mounted side-impact supple-
mental air bag system

This system can help cushion the impact
force to the chest area of the driver and
front passenger in certain side-impact col-
lisions. The side air bags are designed to
inflate on the side where the vehicle is
impacted.

Rear outboard seat-mounted side-impact
supplemental air bag system

This system can help cushion the impact
force to the chest area of the rear outboard
seat passengers in certain side-impact
collisions. The side air bags are designed
to inflate on the side where the vehicle is
impacted.

Roof-mounted curtain side-impact and
rollover supplemental air bag system

This system can help cushion the impact
force to the head of occupants in front and
rear outboard seating positions in certain
side-impact collisions. The curtain air bags
are designed to inflate on the side where
the vehicle is impacted. In a rollover, the
curtain air bags are designed to inflate and
remain inflated for a short time.

LRS3091

SUPPLEMENTAL RESTRAINT SYSTEM
(SRS)

1-40

Safety-Seats, seat belts and supplemental restraint system

Driver and front passenger supplemen-
tal knee air bag

This system can help cushion the impact
force to the driver’s and front passenger’s
knees in certain collisions.

The SRS is designed to

supplement

the

crash protection provided by the driver and
front passenger and rear seat belts and is

not a substitute

for them. Seat belts

should always be correctly worn and the
occupant seated a suitable distance away
from the steering wheel, instrument panel
and door finishers. For additional informa-
tion, see “Seat belts” (P. 1-9).

The supplemental air bags operate only
when the ignition switch is placed in the
ON position.

After placing the ignition switch in the
ON position, the supplemental air bag
warning light illuminates. The supple-
mental air bag warning light will turn off
after about 7 seconds if the system is
operational.

WARNING

•

The front air bags ordinarily will not
inflate in the event of a side impact,
rear impact, rollover, or lower sever-
ity frontal collision. Always wear your
seat belts to help reduce the risk or
severity of injury in various kinds of
accidents

•

The front passenger air bag and front
passenger supplemental knee air bag
will not inflate if the passenger air bag
status light is lit. For additional infor-
mation, see "Front passenger air bag
and status light" (P. 1-51).

WRS0031

Safety-Seats, seat belts and supplemental restraint system

1-41

•

The seat belts and the front air bags
are most effective when you are sit-
ting well back and upright in the seat.
The front air bags inflate with great
force. Even with the NISSAN Ad-
vanced Air Bag System, if you are un-
restrained, leaning forward, sitting
sideways or out of position in any
way, you are at greater risk of injury
or death in a crash. You may also re-
ceive serious or fatal injuries from
the front air bag if you are up against
it when it inflates. Always sit back
against the seatback and as far away
as practical from the steering wheel
or instrument panel. Always properly
use the seat belts.

•

The driver and front passenger seat
belt buckles are equipped with sen-
sors that detect if the seat belts are
fastened. The NISSAN Advanced Air
Bag System monitors the severity of
a collision and seat belt usage, then
inflates the air bags as needed. Fail-
ure to properly wear seat belts can
increase the risk or severity of injury
in an accident.

•

The front passenger seat is equipped
with an occupant classification sensor
(weight sensor) that turns the front
passenger air bag and front passen-
ger supplemental knee air bag OFF
under some conditions. This sensor is
only used in this seat. Failure to be
properly seated and wearing the seat
belt can increase the risk or severity of
injury in an accident. For additional in-
formation, see "Front passenger air
bag and status light" (P. 1-51).

•

Keep hands on the outside of the
steering wheel. Placing them inside
the steering wheel rim could increase
the risk that they are injured when
the front air bag inflates.

1-42

Safety-Seats, seat belts and supplemental restraint system

WARNING

•

Even with the NISSAN Advanced Air
Bag System, never install a rear-facing
child restraint in the front seat. An in-
flating front air bag could seriously
injure or kill your child. For additional
information,

see

“Child

restraints”

(P. 1-19)

WARNING

Front and rear outboard seat-mounted
side-impact supplemental air bags and
roof-mounted curtain side-impact and
rollover supplemental air bags:

•

The side air bags and curtain air bags
ordinarily will not inflate in the event
of a frontal impact, rear impact, or
lower severity side collision. Always
wear your seat belts to help reduce
the risk or severity of injury in various
kinds of accidents.

ARS1045

ARS1046

WRS0431

Safety-Seats, seat belts and supplemental restraint system

1-45

Do not allow anyone sitting in the
front seats or rear outboard seats
to extend their hand out of the win-
dow or lean against the door. Some
examples of dangerous riding posi-
tions are shown in the previous
illustrations.

WARNING

•

When sitting in the rear seat, do not
hold onto the seatback of the front
seat. If the side air bag inflates, you
may be seriously injured. Be especially
careful with children, who should al-
ways be properly restrained. Some ex-
amples of dangerous riding positions
are shown in the illustrations.

•

Do not use seat covers on the front or
rear seatbacks. They may interfere
with side air bag inflation.

WRS0032

Safety-Seats, seat belts and supplemental restraint system

1-47

NISSAN Advanced Air Bag System
(front seats)

1. Roof-mounted curtain side-impact and

rollover supplemental air bag

2. Seat belt with pretensioner(s) (front seats)

3. Shoulder belt height adjustment (front

seats)

4. Side-impact pressure sensor (driver's

side shown; front passenger side similar)

5. Crash zone sensor

6. Supplemental

front-impact

air

bag

modules

7. Driver and front passenger supplemen-

tal knee air bags

8. Air bag Control Unit (ACU)

9. Occupant classification system control

unit

10. Occupant classification sensor (weight

sensor – located in front passenger
cushion frame)

11. Side satellite sensor (passenger’s side

shown; driver side similar) (if so equipped)

12. Front seat-mounted side-impact supple-

mental air bags (passenger’s side shown;
driver side similar)

LRS3668

1-48

Safety-Seats, seat belts and supplemental restraint system

13. Side satellite sensor (passenger’s side

shown; driver side similar)

14. Rear outboard seat-mounted side-

impact supplemental air bags

15. Seat belt with pretensioner(s) (rear seats)

WARNING

To ensure proper operation of the
passenger’s NISSAN Advanced Air Bag
System, please observe the following
items.

•

Do not allow a passenger in the rear
seat to push or pull on the seatback
pocket.

•

Do not place heavy loads heavier
than 9.1 lbs. (4 kg) on the seatback,
head restraint/headrest or in the
seatback pocket.

•

Make sure that there is nothing press-
ing against the rear of the seatback,
such as a child restraint installed in the
rear seat or an object stored on the
floor.

•

Make sure that there is no object
placed under the front passenger seat.

•

Make sure that there is no object
placed between the seat cushion and
the center console or between the
seat cushion and the door.

•

If a forward-facing child restraint is
installed in the front passenger seat,
do not position the front passenger
seat so the child restraint contacts
the instrument panel. If the child re-
straint does contact the instrument
panel, the system may determine the
seat is occupied and the passenger
air bag and front passenger supple-
mental knee air bag may deploy in a
collision. Also the front passenger air
bag status light may not illuminate.
For additional information, see “Child
restraints” (P. 1-19).

•

Confirm the operating condition with
the front passenger air bag status
light.

•

If you notice that the front passenger
air bag status light is not operating as
described in this section, get the occu-
pant classification system checked.
It is recommended that you visit a
NISSAN dealer for this service.

•

Until you have confirmed with a
dealer that your front passenger seat
occupant classification system is
working properly, position the occu-
pants in the rear seating positions.

•

Do not position the front passenger
seat so it contacts the rear seat. If the
front seat does contact the rear seat,
the air bag system may determine a
sensor malfunction has occurred
and the front passenger air bag sta-
tus light may illuminate and the
supplemental air bag warning light
may flash.

This vehicle is equipped with the NISSAN
Advanced Air Bag System for the driver and
front passenger seats. This system is de-
signed to meet certification requirements
under U.S. regulations. It is also permitted in
Canada.

However, all of the information,

cautions and warnings in this manual
still apply and must be followed.

The driver supplemental front-impact air
bag is located in the center of the steering
wheel. The front passenger supplemental
front-impact air bag is mounted in the
dashboard above the glove box. The front
air bags are designed to inflate in higher

Safety-Seats, seat belts and supplemental restraint system

1-49

severity frontal collisions, although they
may inflate if the forces in another type of
collision are similar to those of a higher se-
verity frontal impact. They may not inflate in
certain frontal collisions. Vehicle damage (or
lack of it) is not always an indication of
proper front air bag system operation.

The NISSAN Advanced Air Bag System
monitors information from the crash zone
sensor, the Air bag Control Unit (ACU), seat
belt buckle sensors and occupant classifi-
cation sensor (weight sensor). Inflator op-
eration is based on the severity of a colli-
sion and seat belt usage for the driver. For
the front passenger, the occupant classifi-
cation sensors are also monitored. Based
on information from the sensors, only one
front air bag may inflate in a crash, depend-
ing on the crash severity and whether the
front occupants are belted or unbelted. Ad-
ditionally, the front passenger air bag and
front passenger supplemental knee air
bag may be automatically turned OFF un-
der some conditions, depending on the
weight detected on the front passenger
seat and how the seat belt is used. If the
front passenger air bag and front passen-
ger supplemental knee air bag are OFF, the
front passenger air bag status light will be

illuminated. For additional information, see
"Front passenger air bag and status light"
(P. 1-51). One front air bag inflating does not
indicate improper performance of the
system.

If you have any questions about your air
bag system, it is recommended that you
visit a NISSAN dealer. If you are considering
modification of your vehicle due to a dis-
ability, you may also contact NISSAN. Con-
tact information is contained in the front of
this Owner's Manual.

When a front air bag inflates, a fairly loud
noise may be heard, followed by the re-
lease of smoke. This smoke is not harmful
and does not indicate a fire. Care should be
taken to not inhale it, as it may cause irrita-
tion and choking. Those with a history of a
breathing condition should get fresh air
promptly.

Front air bags, along with the use of seat
belts, help to cushion the impact force on
the face and chest of the front occupants.
They can help save lives and reduce seri-
ous injuries. However, an inflating front air
bag may cause facial abrasions or other
injuries. Front air bags do not provide re-
straint to the lower body.

Even with NISSAN air bags, seat belts
should be correctly worn and the driver
and front passenger seated upright as far
as practical away from the steering wheel
or instrument panel. The front air bags in-
flate quickly in order to help protect the
front occupants. Because of this, the force
of the front air bag inflating can increase
the risk of injury if the occupant is too close
to, or is against, the front air bag module
during inflation.

The front air bags deflate quickly after a
collision.

The front air bags operate only when the
ignition switch is placed in the ON position.

1-50

Safety-Seats, seat belts and supplemental restraint system

Front passenger air bag and status
light

WARNING

The front passenger air bag and front
passenger supplemental knee air bag
are designed to automatically turn OFF
under some conditions. Read this sec-
tion carefully to learn how it operates.
Proper use of the seat, seat belt, and
child restraints is necessary for most
effective protection. Failure to follow all

instructions in this manual concerning
the use of seats, seat belts, and child
restraints can increase the risk or se-
verity of injury in an accident.

Status light

The front passenger seat is equipped with
an occupant classification sensor (weight
sensor) that turns the front passenger air
bag and front passenger supplemental
knee air bag on or off depending on the
weight applied to the front passenger seat.
The status of the front passenger air bag
(ON or OFF) is indicated by the front pas-
senger air bag status light

which is

located on the instrument panel.

After the ignition switch is placed in the
"ON" position, the front passenger air bag
status light on the instrument panel illumi-
nates for about 7 seconds and then turns
off or remains illuminated depending on
the front passenger seat occupied status.
The light operates as follows:
• Unoccupied front passenger's seat: The

light is ON and the front passenger

air bag and front passenger supplemen-
tal knee air bag are OFF and will not in-
flate in a crash.

• Front passenger seat occupied by a

small adult, child or child restraint as
outlined in this section: The

light

illuminates to indicate that the front pas-
senger air bag and front passenger
supplemental knee air bag are OFF and
will not inflate in a crash.

• Occupied front passenger seat and the

passenger meets the conditions as out-
lined in this section: The

light is OFF

to indicate that the front passenger air
bag and front passenger supplemental
knee air bag are operational.

In addition to the above, certain objects
placed on the front passenger seat may
also cause the light to operate as de-
scribed above depending on their weight.

For additional information related to the
normal operation and troubleshooting of
this occupant classification sensor system,
please see “Normal operation” (P. 1-53) and
“Troubleshooting” (P. 1-54).

Front passenger air bag

The front passenger air bag is designed to
automatically turn OFF when the vehicle
is operated under some conditions as
described below in accordance with U.S.
regulations. If the front passenger air bag is

LRS3091

Safety-Seats, seat belts and supplemental restraint system

1-51

OFF, it will not inflate in a crash. The driver
air bag and other air bags in your vehicle
are not part of this system.

The purpose of the regulation is to help
reduce the risk of injury or death from an
inflating air bag to certain front passenger
seat occupants, such as children, by requir-
ing the air bag to be automatically turned
OFF. Certain sensors are used to meet the
requirements.

The occupant classification sensor in this
vehicle is a weight sensor. It is designed to
detect an occupant and objects on the
seat by weight. For example, if a child is in
the front passenger seat, the NISSAN Ad-
vanced Air Bag System is designed to turn
the front passenger air bag OFF in accor-
dance with the regulations. Also, if a child
restraint of the type specified in the regula-
tions is on the seat, its weight and the
child’s weight can be detected and cause
the air bag to turn OFF.

Front passenger seat adult occupants who
are properly seated and using the seat belt
as outlined in this manual should not cause
the front passenger air bag and front pas-
senger supplemental knee air bag to be
automatically turned OFF. For small adults it

may be turned OFF, however if the occupant
takes his/her weight off the seat cushion
(for example, by not sitting upright, by sitting
on an edge of the seat, or by otherwise be-
ing out of position), this could cause the sen-
sor to turn the air bag OFF. Always be sure to
be seated and wearing the seat belt prop-
erly for the most effective protection by the
seat belt and supplemental air bag.

NISSAN recommends that pre-teens and
children be properly restrained in a rear
seat. NISSAN also recommends that ap-
propriate child restraints and booster
seats be properly installed in a rear seat. If
this is not possible, the occupant classifica-
tion sensor is designed to operate as de-
scribed above to turn the front passenger
air bag and front passenger supplemental
knee air bag OFF for specified child re-
straints as required by the regulations. Fail-
ing to properly secure child restraints and
to use the ALR mode may allow the re-
straint to tip or move in a collision or sud-
den stop. This can also result in the front
passenger air bag and front passenger
supplemental knee air bag inflating in a
crash instead of being OFF. For additional
information, see “Child restraints” (P. 1-19) in
this section.

If the front passenger seat is not occupied,
the front passenger air bag and front pas-
senger supplemental knee air bag are de-
signed not to inflate in a crash. However,
heavy objects placed on the seat could re-
sult in air bag inflation, because of the ob-
ject’s weight detected by the occupant
classification

sensor.

Other

conditions

could also result in air bag inflation, such as
if a child is standing on the seat, or if two
children are on the seat, contrary to the
instructions in this manual. Always be sure
that you and all vehicle occupants are
seated and restrained properly.

Using the front passenger air bag status
light, you can monitor when the front
passenger air bag and front passenger
supplemental knee air bag are automati-
cally turned OFF with the seat occupied.
The light will illuminate when the front pas-
senger seat is unoccupied.

If an adult occupant is in the seat but the
front passenger air bag status light is illu-
minated (indicating that the front passen-
ger air bag and front passenger supple-
mental knee air bag are OFF), it could be
that the person is a small adult, or is not
sitting on the seat properly or not using the
seat belt properly.

1-52

Safety-Seats, seat belts and supplemental restraint system

If a child restraint must be used in the front
seat, the front passenger air bag status
light may or may not be illuminated, de-
pending on the size of the child and the
type of child restraint being used. If the air
bag status light is not illuminated (indicat-
ing that the air bag might inflate in a crash),
it could be that the child restraint or seat
belt is not being used properly. Make sure
that the child restraint is installed properly,
the seat belt is used properly and the occu-
pant is positioned properly. If the air bag
status light is still not illuminated, reposi-
tion the occupant or child restraint in a rear
seat.

If the front passenger air bag status light
will not illuminate even though you believe
that the child restraint, the seat belts and
the occupant are properly positioned, it is
recommended that you take your vehicle
to a NISSAN dealer. A NISSAN dealer can
check that the system is OFF by using a
special tool. However, until you have con-
firmed with a dealer that your air bag is
working properly, reposition the occupant
or child restraint in a rear seat.

The NISSAN Advanced Air Bag System and
front passenger air bag status light will
take a few seconds to register a change in
the front passenger seat status. This is nor-
mal system operation and does not indi-
cate a malfunction.

If a malfunction occurs in the front passen-
ger air bag system, the supplemental air
bag warning light

, located in the me-

ter and gauges area of the instrument
panel, will blink. Have the system checked. It
is recommended that you visit a NISSAN
dealer for this service.

Normal operation

In order for the occupant classification
sensor system to classify the front passen-
ger based on weight, please follow the pre-
cautions and steps outlined below:

Precautions

• Make sure that there are no objects

weighing over 9.1 lbs. (4 kg) hanging on
the seat or placed in the seatback pocket.

• Make sure that a child restraint or other

object is not pressing against the rear of
the seatback.

• Make sure that a rear passenger is not

pushing or pulling on the back of the front
passenger seat.

• Make sure that the front passenger seat

or seatback is not forced back against an
object on the seat or floor behind it.

• Make sure that there is no object placed

under the front passenger seat.

Steps

1. Adjust the seat as outlined in the “Seats”

(P. 1-2) section of this manual. Sit upright,
leaning against the seatback, and cen-
tered on the seat cushion with your feet
comfortably extended to the floor.

2. Make sure there are no objects on your

lap.

3. Fasten the seat belt as outlined in the

“Seat belts” (P. 1-9) section of this manual.

4. Remain in this position for 30 seconds

allowing the system to classify the front
passenger before the vehicle is put into
motion.

5. Ensure proper classification by checking

the front passenger air bag status light.

Safety-Seats, seat belts and supplemental restraint system

1-53

Nissan Versa (2024 year). Manual in english - page 2