Nissan Pathfinder (2024 year). Manual in english

LIFTGATE POSITION SETTING (if so
equipped)

The liftgate can be set to open to a specific
height by performing the following:

1. Open the liftgate using the liftgate

opener switch or the Intelligent Key.

2. Pull the liftgate down to the desired po-

sition and hold the liftgate (the liftgate
will have some resistance when being
manually adjusted).

3. While holding the liftgate in position,

push and hold the liftgate switch

lo-

cated on the liftgate for approximately 5
seconds or until two beeps are heard.

The liftgate will open to the selected posi-
tion setting. To change the position of the
liftgate, repeat steps 1-3 for setting the po-
sition of the liftgate.

OPENING THE FUEL-FILLER DOOR

This vehicle is equipped with a locking fuel
lid that is connected to the driver side door
lock switch.

Before attempting to open fuel-filler door,
first unlock driver side door lock either by
using key fob or the door unlock switch
located on the driver side door inside the
vehicle.

To open the fuel-filler door, push the right
side of the fuel-filler door to release.

LPD3356

LPD2725

FUEL-FILLER DOOR

3-30

Pre-driving checks and adjustments

WARNING

•

Gasoline is extremely flammable and
highly explosive under certain condi-
tions. You could be burned or seri-
ously injured if it is misused or mis-
handled. Always stop the engine and
do not smoke or allow open flames
or sparks near the vehicle when
refueling.

•

Do not attempt to top off the fuel
tank after the fuel pump nozzle
shuts off automatically. Continued
refueling may cause fuel overflow,
resulting in fuel spray and possibly a
fire.

•

Never pour fuel into the throttle body
to attempt to start your vehicle.

•

Do not fill a portable fuel container in
the vehicle or trailer. Static electricity
can cause an explosion of flammable
liquid, vapor or gas in any vehicle or
trailer. To reduce the risk of serious
injury or death when filling portable
fuel containers:

–

Always place the container on the

ground when filling.

–

Do not use electronic devices when

filling.

–

Keep the pump nozzle in contact

with the container while you are
filling it.

–

Use only approved portable fuel

containers for flammable liquid.

CAUTION

•

Do not use a fuel containing more
than 15% ethanol in your vehicle. For
additional information, see “Fuel rec-
ommendation” (P. 10-4).

•

For additional information, see “Mal-
function Indicator Light (MIL)” (P. 2-21).

•

If fuel is spilled on the vehicle body,
flush it away with water to avoid
paint damage.

LPD3158

Pre-driving checks and adjustments

3-31

HOW TO REFUEL

The fuel tank is not equipped with a fuel
filler cap. After opening the fuel-filler door,
insert the fuel pump nozzle directly into the
fuel-filler opening. When the fuel pump
nozzle is pulled out, the fuel filler opening
will be sealed.

To refuel:

Be sure to insert the fuel pump nozzle
slowly into the fuel-filler opening as far as it
will go before fueling.

Never move the nozzle during the
refueling.

Pull out the nozzle approximately 5 sec-
onds after the fuel pump nozzle shuts off
automatically (initial shut-off).

Close the fuel-filler door after refueling.

If you need to refuel from a portable fuel
container, use the funnel supplied with your
vehicle. (see “When refueling from a por-
table fuel container” (P. 3-33).

CAUTION

•

Do not attempt to open the flaps on
the fuel-filler opening using any tool
other than the fuel pump nozzle.

•

This fuel-filler opening is only con-
formable to normal fuel pump nozzles
at gas stations. Using a nozzle with a
small diameter may damage the
opening and the fuel system.

•

If fuel is spilled on the vehicle body,
flush it away with water to avoid
paint damage.

WARNING

•

Gasoline is extremely flammable and
highly explosive under certain condi-
tions. You could be burned or seriously
injured if it is misused or mishandled.

Always stop the engine and do not
smoke or allow open flames or sparks
near the vehicle when refueling.

•

Do not attempt to top off the fuel tank
after the fuel pump nozzle shuts off
automatically.

Continued

refueling

may cause fuel overflow, resulting in
fuel spray and possibly a fire.

•

Never pour fuel into the throttle body
to attempt to start your vehicle.

•

–

Always place the container on the

ground when filling.

–

Do not use electronic devices

when filling.

–

Keep the pump nozzle in contact

with the container while you are
filling it.

–

Use only approved portable fuel

containers for flammable liquid.

LPD3273

3-32

Pre-driving checks and adjustments

WHEN REFUELING FROM A
PORTABLE FUEL CONTAINER

If you need to refuel from a portable fuel
container, use the funnel

stored in the

tool bag (located under the luggage
board).

Be sure to insert the funnel into the fuel-
filler opening slowly and fully. Insert the
nozzle of the portable fuel container into
the opening along the funnel and fill the
fuel tank.

After refueling, remove the funnel from the
fuel-filler opening. Wipe the funnel clean
and return it to the tool bag.

CAUTION

•

Do not insert the nozzle of the por-
table fuel container directly into the
fuel-filler opening. Doing so may
damage the opening and the fuel
system.

•

Use only the funnel provided with
your vehicle. Otherwise the fuel-filler
opening and the fuel system may be
damaged.

WARNING

•

Do not adjust the steering wheel
while driving. You could lose control
of

your

vehicle

and

cause

accident.

•

Do not adjust the steering wheel any
closer to you than is necessary for
proper steering operation and com-
fort. The driver's air bag inflates with
great force. If you are unrestrained,
leaning forward, sitting sideways or
out of position in any way, you are at
greater risk of injury or death in a
crash. You may also receive serious
or fatal injuries from the air bag if you
are up against it when it inflates. Al-
ways sit back against the seatback
and as far away as practical from the
steering wheel. Always use the seat
belts.

LPD3275

STEERING WHEEL

Pre-driving checks and adjustments

3-33

MANUAL OPERATION (if so
equipped)

Tilt and telescopic operation

Push the lock lever

down:

• Adjust the steering wheel up or down in

direction

to the desired position.

• Adjust the steering wheel forward or

backward in direction

to the desired

position.

Pull the lock lever

up firmly to lock the

steering wheel in place.

AUTOMATIC OPERATION (if so
equipped)

Tilt and telescopic operation

To adjust the steering wheel move the
switch

in the following directions:

• Adjust the steering wheel up or down in

direction

to the desired tilt position.

• Adjust the steering wheel forward or

backward in direction

to the desired

telescopic position.

CAUTION

For vehicles with memory seat: Failure
to reset the tilt and telescoping func-
tions of the steering wheel, after the
vehicle’s battery has been discharged,
may prevent the steering wheel posi-
tion from being adjusted.

For vehicles with memory seat: Both the tilt
and telescopic steering operation must be
reset after the vehicle’s battery has been
discharged in order to prevent the tilt and
telescopic operation from locking in one
position. When the battery has been re-
charged or replaced, perform the following:
• For tilt operation: Adjust the switch

the steering wheel moves to the highest
position

that can be reached.

• For

telescopic

operation: Adjust

the

switch

so the steering wheel moves to

the most forward and backward position

that can be reached.

Performing these operations resets the
range of the steering wheel’s tilt and tele-
scopic function.

LPD3169

LPD3170

3-34

Pre-driving checks and adjustments

Entry/Exit function

The memory seat will make the steering
wheel move up automatically when the
driver's door is opened and the ignition
switch is in the LOCK position. This lets the
driver get into and out of the seat more
easily. The steering wheel moves back into
position when the driver's door is closed
and the ignition switch is pushed.

For additional information, see “Memory
seat” (P. 3-40).

1. To block glare from the front, swing

down the sun visor

2. To block glare from the side, remove the

sun visor from the center mount and
swing the visor to the side

3. Slide the sun visor extension

in or out

as needed.

CAUTION

•

Do not store the sun visor before re-
turning the extension to its original
position.

•

Do not pull the extension sun visor
forcedly downward.

LPD2154

SUN VISORS

Pre-driving checks and adjustments

3-35

VANITY MIRRORS

To access the vanity mirror, pull the sun
visor down and flip open the mirror cover.
Some vanity mirrors will illuminate when
the mirror cover is open.

CARD HOLDER

To use the card holder, slide card into the
clip. Do not view information while operat-
ing the vehicle.

MANUAL ANTI-GLARE REARVIEW
MIRROR (if so equipped)

Use the night position

to reduce glare

from the headlights of vehicles behind you
at night.

Use the day position

when driving in

daylight hours.

WARNING

Use the night position only when nec-
essary, because it reduces rear view
clarity.

LPD3174

LPD3156

Driver’s and passenger’s side

WPD0126

MIRRORS

3-36

Pre-driving checks and adjustments

AUTOMATIC ANTI-GLARE
REARVIEW MIRROR (if so equipped)

The inside mirror is designed so that it au-
tomatically dims during nighttime condi-
tions and according to the intensity of
the headlights of the vehicle following you.
The automatic anti-glare feature is acti-
vated when the ignition switch is in the ON
position.

NOTE:

Do not hang any objects over the sen-
sors

or apply glass cleaner to the sen-

sors. Doing so will reduce the sensitivity
of the sensors, resulting in improper
operation.

For additional information on HomeLink®
Universal

Transceiver

operation,

see

“HomeLink® Universal Transceiver” (P. 2-129).

OUTSIDE MIRRORS

The outside mirror remote control will op-
erate when the ignition switch is in the ACC
or ON position or after the ignition switch is
placed in the OFF position for 45 seconds
or until a door is opened.

Push the switch

to select the left

or right mirror. Adjust each mirror to the
desired position using the large switch

Push the switch

and make sure

that the corresponding light is off, to pre-
vent accidentally moving the mirror.

LPD3366

LPD3166

Pre-driving checks and adjustments

3-37

WARNING

•

Objects viewed in the outside mirror
on the passenger side are closer than
they appear. Be careful when moving
to the right. Using only this mirror
could cause an accident. Use the in-
side mirror or glance over your
shoulder to properly judge distances
to other objects.

•

Do not adjust the mirrors while driv-
ing. You could lose control of your ve-
hicle and cause an accident.

Manual folding outside mirrors
(if so equipped)

Pull the outside mirror toward the door to
fold it.

Power folding outside mirrors
(if so equipped)

CAUTION

•

Do not touch the mirrors while they are
moving. Your hand may be pinched,
and the mirror may malfunction.

•

Do not drive with the mirrors stored.
You will be unable to see behind the
vehicle.

Push the switch

to open the mirrors.

Push the switch again to close the mirrors.

LPD2112

LPD3186

3-38

Pre-driving checks and adjustments

If one of the mirrors are manually operated
or bumped, the mirror body can become
loose at the pivot point. To correct elec-
tronic mirror operation, cycle the mirrors by
pushing the switch

until completely

closed, then push the switch again until the
mirrors are in the open position

Heated mirrors (if so equipped)

The electric control type outside mirrors
can be heated to defrost, defog, or de-ice
for improved visibility. For additional infor-
mation, see “Rear window and outside
mirror (if so equipped) defroster switch”
(P. 2-84).

Reverse tilt-down feature (if so
equipped)

The reverse tilt-down feature will turn the
corresponding

outside

mirror

surface

downward when the mirror control switch
is in the L or R position. This provides better
rear visibility close to the vehicle.

The mirrors automatically return to their
original position when you shift out of R
(Reverse).

The outside mirror surfaces will return to
their original position when one of the fol-
lowing conditions has occurred:
• The shift lever is moved to any position

other than R (Reverse).

• The outside mirror control switch is set to

the neutral or center position.

• The ignition switch is placed in the OFF

position.

The reverse tilt position can be changed.
While in R (Reverse), adjust the glass posi-
tion to the desired location. The next time
the vehicle is shifted into R (Reverse), the
glass position will go to the newly set posi-
tion. Additionally, the changed reverse tilt
position can be saved to a memory seat
position. After the reverse tilt glass position
has been changed, vehicle is shifted back
into park and glass has returned to the
original position, push the Set switch and
push the desired memory switch (1 or 2)
to assign the new reverse tilt position
memory.

NOTE:

If the outside mirror control switch is in
the center position, the mirror surface
will NOT turn downward when the shift
lever is moved to R (Reverse).

For additional information, see “Memory
seat” (P. 3-40).

Pre-driving checks and adjustments

3-39

The memory seat system has three
features:
• Memory storage function (Key-link)
• Memory storage function (Switch)
• Entry/exit function

Key-link, when enabled, automatically re-
tains the driver’s last seat, automatic steer-
ing wheel, and outside mirror positions for
that specific key when the ignition is posi-
tioned from ON to OFF.

Each memory switch button (1 or 2) on the
driver’s door can also store one additional
position which is independent of the key-
linked position.

MEMORY STORAGE FUNCTION
(key-link)

Use the following process to setup key-link:

1. Unlock the vehicle with the desired Intel-

ligent Key while the ignition is OFF.

2. Place the ignition in the ON position or

start the engine.

3. Within the settings menu of the touch-

screen display, select “Edit User” and
then “Synch Profile with Intelligent Key”.

4. Turn “Synch Profile with Intelligent Key”

ON. The ON button will light up.

5. Within the settings menu of the touch-

screen display, select “Edit User” and
then “User Profiles”.

6. Create a personal profile and make sure

the correct key number is selected with
the arrow.

7. Set the desired seat, steering and mirror

positions.

8. Place the ignition switch in the OFF po-

sition and lock the vehicle with the Intel-
ligent Key.

Once Step 8 is completed, every time the
vehicle is unlocked using the Intelligent Key
and the ignition is placed in the ON posi-
tion, the memory positions will be recalled.

For

additional

information,

see

the

“NissanConnect® Owner’s Manual.

Follow the same procedure if you want
to link the 2nd, 3rd or 4th Intelligent Key.

NOTE:
• If new memory positions are set prior

to turning the ignition from ON to OFF,
the previously linked memory posi-
tions for the respective key will be
overwritten by new positions.

• Please make sure only one Intelligent

Key is in the vehicle when setting
memory to Intelligent Key. If more than
one key is in the vehicle wrong key may
be selected.

Recalling Intelligent Key memory
positions

If the “Key-Linked Settings” (if so equipped)
are enabled in the vehicle information dis-
play for that particular key, every time you
enter the vehicle the driver’s seat, auto-
matic steering wheel (if so equipped), and
outside mirrors will automatically move to
the driver’s last position of the respective
Intelligent Key.

NOTE:

The key-linked memory positions can be
different from the positions stored in the
memory switch (1 or 2).

MEMORY SEAT (if so equipped)

3-40

Pre-driving checks and adjustments

MEMORY STORAGE FUNCTION
(switch)

Two positions for the driver's seat, steering
wheel (if so equipped) and outside mirrors
can be stored in the memory seat system.
Follow

these

procedures

use

the

memory system.

1. Place the ignition in the ON or ACC posi-

tion (the vehicle should be stopped while
setting the memory).

2. Adjust the driver's seat, steering wheel (if

so equipped) and outside mirrors to the
desired positions by manually operating
each adjusting switch. For additional in-
formation, see “Seats” (P. 1-2), “Steering
wheel” (P. 3-33) and “Outside mirrors”
(P. 3-37).

3. Push the SET switch and, within 5 sec-

onds, push the memory switch (1 or 2).

4. The indicator light for the pushed

memory switch will come on and stay
on for approximately 5 seconds.

5. The chime will sound if the memory has

been stored.

NOTE:

If a new memory position is stored in the
same memory switch, the previous
memory position will be overwritten by
the new stored position.

Confirming memory storage

• Push the SET switch.
• If a memory position has been stored in

the switch (1 or 2) then the indicator light
for the respective switch will stay on for
approximately 5 seconds.

ENTRY/EXIT FUNCTION

This system is designed so that the driver's
seat and steering wheel will automatically
move when the shift position is in the P
(Park) position. This allows the driver to
easily get in and out of the driver’s seat.

The driver’s seat will slide backward and
the steering wheel will move up:
• When the driver’s door is opened with the

ignition switch in the OFF position.

• When the ignition switch is changed from

ACC to OFF with the driver’s door open.

The driver’s seat and steering wheel will
return to the previous position:
• When the ignition switch is changed from

ACC or ON while the shift position is in the
P (Park) position.

The entry/exit function can be adjusted or
canceled through “Vehicle Settings” in the
vehicle information display by performing
the following:
• Switch the Exit Seat Slide from on to off.
• Switch the Exit Steering UP from on to off.

LPD3165

Pre-driving checks and adjustments

3-41

Restarting the entry/exit function

If the battery cable is disconnected or if the
fuse opens, the stored memory positions
may be lost and some of the functions will
be restricted.

1. Drive the vehicle over 25 mph (40 km/h).

2. Open and close the driver's door more

than two times with the ignition switch
in the OFF position.

The entry/exit function should now work
properly.

SETTING MEMORY FUNCTION

The position of the following settings can
be linked to the Intelligent Key and the
memorized settings can be available for
each Intelligent Key.
• Climate control system
• Audio system

To use the memory function, set the cli-
mate and audio systems to the driver's
preferred settings. Lock the doors with the
Intelligent Key. Each Intelligent Key may be
set with the driver's individual preferences.

To engage the memorized settings, per-
form the following:

1. Carry the Intelligent Key that is linked to

the memorized settings.

2. Unlock the doors by wrapping hand

around the capacitive door handle or
pressing the

button on the Intelli-

gent Key.

3. Place the ignition switch in the ON posi-

tion. The settings linked to the Intelligent
Key will start.

For additional information on using the cli-
mate control system, see “Heater and air
conditioner (automatic)” (P. 4-32).

SYSTEM OPERATION

The memory seat system will not work or
will stop operating under the following
conditions:
• When the vehicle speed is above 4 mph (7

km/h).

• When any of the memory switches are

pushed while the memory seat system is
operating.

• When the switch for the driver’s seat and

steering wheel is pushed while the
memory seat system is operating.

• When the seat has already been moved

to the memorized position.

• When no seat position is stored in the

memory switch.

• When the shift position is moved from P

(Park) position to any other position.

3-42

Pre-driving checks and adjustments

1. CAMERA button

WARNING

•

Failure to follow the warnings and in-
structions for proper use of the Rear-
View Monitor system could result in
serious injury or death.

•

RearView Monitor is a convenience
feature and is not a substitute for
proper backing. Always turn and look
out the windows and check mirrors
to be sure that it is safe to move be-
fore operating the vehicle. Always
back up slowly.

•

The system is designed as an aid to
the driver in showing large station-
ary objects directly behind the ve-
hicle, to help avoid damaging the
vehicle.

LHA5430

REARVIEW MONITOR (if so
equipped)

Monitor, climate, audio, phone and voice recognition systems

4-3

•

The distance guide line and the ve-
hicle width line should be used as a
reference only when the vehicle is on
a level paved surface. The distance
viewed on the monitor is for refer-
ence only and may be different than
the actual distance between the ve-
hicle and displayed objects.

CAUTION

Do not scratch the camera lens when
cleaning dirt or snow from the front of
the camera.

The RearView Monitor system automati-
cally shows a rear view of the vehicle when
the shift lever is shifted into the R (Reverse)
position. The radio can still be heard while
the RearView Monitor is active.

To display the rear view, the RearView Moni-
tor system uses a camera located in the
rear bumper

REARVIEW MONITOR SYSTEM
OPERATION

With the ignition switch in the ON position,
move the shift lever to the R (Reverse) po-
sition to operate the RearView Monitor.

HOW TO READ THE DISPLAYED LINES

Guiding lines which indicate the vehicle
width and distances to objects with refer-
ence to the vehicle body line

are dis-

played on the monitor.

Distance guide lines

Indicate distances from the vehicle body.
• Red line

: approx. 1.5 ft (0.5 m)

• Yellow line

: approx. 3 ft (1 m)

• Green line

: approx. 7 ft (2 m)

Vehicle width guide lines

Indicate the vehicle width when backing up.

LHA5431

LHA4805

4-4

Monitor, climate, audio, phone and voice recognition systems

Predicted course lines

Indicate the predicted course when back-
ing up. The predicted course lines will be
displayed on the monitor when the shift
lever is in the R (Reverse) position and the
steering wheel is turned. The predicted
course lines will move depending on how
much the steering wheel is turned and will
not be displayed while the steering wheel is
in the straight-ahead position.

The vehicle width guide lines and the width
of the predicted course lines are wider than
the actual width and course.

DIFFERENCE BETWEEN PREDICTED
AND ACTUAL DISTANCES

The displayed guidelines and their loca-
tions on the ground are for approximate
reference only. Objects on uphill or downhill
surfaces or projecting objects will be actu-
ally located at distances different from
those displayed in the monitor relative to
the guidelines (refer to illustrations). When
in doubt, turn around and view the objects
as you are backing up, or park and exit the
vehicle to view the positioning of objects
behind the vehicle.

Backing up on a steep uphill

When backing up the vehicle up a hill, the
distance guide lines and the vehicle width
guide lines are shown closer than the ac-
tual distance. Note that any object on the
hill is further than it appears on the
monitor.

Backing up on a steep downhill

When backing up the vehicle down a hill,
the distance guide lines and the vehicle
width guide lines are shown farther than
the actual distance. Note that any object
on the hill is closer than it appears on the
monitor.

LHA5432

LHA5433

Monitor, climate, audio, phone and voice recognition systems

4-5

Backing up near a projecting
object

The predicted course lines

do not touch

the object in the display. However, the ve-
hicle may hit the object if it projects over
the actual backing up course.

Backing up behind a projecting
object

The position

is shown farther than the

position

in the display. However, the po-

sition

is actually at the same distance as

the position

. The vehicle may hit the

object when backing up to the position

if the object projects over the actual back-
ing up course.

HOW TO PARK WITH PREDICTED
COURSE LINES

WARNING

•

If the tires are replaced with different
sized tires, the predicted course lines
may be displayed incorrectly.

•

On a snow-covered or slippery road,
there may be a difference between
the predicted course line and the ac-
tual course line.

•

If the battery is disconnected or be-
comes discharged, the predicted
course lines may be displayed incor-
rectly. If this occurs, please perform
the following procedures:

–

Turn the steering wheel from lock
to lock while the engine is running.

–

Drive the vehicle on a straight road
for more than 5 minutes.

•

When the steering wheel is turned
with the ignition switch in the ACC
position, the predicted course lines
may be displayed incorrectly.

LHA4995

LHA5434

4-6

Monitor, climate, audio, phone and voice recognition systems

1. Visually check that the parking space is

safe before parking your vehicle.

2. The rear view of the vehicle is displayed

on the screen

when the shift lever is

moved to the R (Reverse) position.

3. Slowly back up the vehicle adjusting the

steering wheel so that the predicted
course lines

enter the parking space

4. Maneuver the steering wheel to make

the vehicle width guide lines

parallel

to the parking space

while referring

to the predicted course lines.

5. When the vehicle is parked in the space

completely, move the shift lever to the P
(Park) position and apply the parking
brake.

LHA5043

LHA4770

Monitor, climate, audio, phone and voice recognition systems

4-7

ADJUSTING THE SCREEN

1. Press the CAMERA button.

2. Touch the “Display Settings” key.

3. Touch the “Brightness”, “Contrast”, Tint”,

“Color”, or “Black Level” key.

4. Adjust the item by touching the “+” or “–”

key on the touch-screen display.

NOTE:

Do not adjust any of the display settings
of the RearView Monitor while the ve-
hicle is moving.

HOW TO TURN ON AND OFF
PREDICTED COURSE LINES

To toggle on and off the predicted course
lines while in the P (Park) position:

1. Press the CAMERA button.

2. Touch the “Predicted Course Lines” key

to turn the feature on or off.

REARVIEW MONITOR SYSTEM
LIMITATIONS

WARNING

Listed below are the system limitations
for RearView Monitor. Failure to oper-
ate the vehicle in accordance with
these system limitations could result in
serious injury or death.

•

The system cannot completely elimi-
nate blind spots and may not show
every object.

•

Underneath the bumper and the cor-
ner areas of the bumper cannot be
viewed on the RearView Monitor be-
cause of its monitoring range limita-
tion. The system will not show small
objects below the bumper, and may
not show objects close to the bum-
per or on the ground.

•

Objects

viewed

the

RearView

Monitor differ from actual distance
because a wide-angle lens is used.

•

Objects in the RearView Monitor will
appear visually opposite compared
to when viewed in the rearview and
outside mirrors.

•

Use the displayed lines as a refer-
ence. The lines are highly affected by
the number of occupants, fuel level,
vehicle position, road conditions and
road grade.

•

Make sure that the liftgate is securely
closed when backing up.

•

Do not put anything on the rearview
camera. The rearview camera is in-
stalled in the rear bumper.

•

When washing the vehicle with high
pressure water, be sure not to spray it
around the camera. Otherwise, water
may enter the camera unit causing
water condensation on the lens, a
malfunction, fire or an electric shock.

•

Do not strike the camera. It is a preci-
sion instrument. Otherwise, it may
malfunction or cause damage result-
ing in a fire or an electric shock.

LHA5512

4-8

Monitor, climate, audio, phone and voice recognition systems

The following are operating limitations and
do not represent a system malfunction:
• When the temperature is extremely high

or low, the screen may not clearly display
objects.

• When strong light directly shines on the

camera, objects may not be displayed
clearly.

• Vertical lines may be seen in objects on

the screen. This is due to strong reflected
light from the bumper.

• The screen may flicker under fluorescent

light.

• The colors of objects on the RearView

Monitor may differ somewhat from the
actual color of objects.

• Objects on the monitor may not be clear

in a dark environment.

• There may be a delay when switching

between views.

• If dirt, rain or snow accumulate on the

camera, the RearView Monitor may not
display objects clearly. Clean the camera.

• Do not use wax on the camera lens. Wipe

off any wax with a clean cloth dampened
with a diluted mild cleaning agent, then
wipe with a dry cloth.

SYSTEM MAINTENANCE

CAUTION

•

Do not use alcohol, benzine or thin-
ner to clean the camera. This will
cause discoloration.

•

Do not damage the camera as the
monitor screen may be adversely
affected.

If dirt, rain or snow accumulates on the
camera

, the RearView Monitor may not

display objects clearly. Clean the camera
by wiping it with a cloth dampened with a
diluted mild cleaning agent and then wip-
ing it with a dry cloth.

LHA5431

Monitor, climate, audio, phone and voice recognition systems

4-9

WARNING

•

Failure to follow the warnings and in-
structions for the proper use of the
Intelligent

Around View®

Monitor

system could result in serious injury
or death.

•

The Intelligent Around View® Monitor
is a convenience feature and is not a
substitute for proper vehicle opera-
tion because it has areas where ob-
jects cannot be viewed. The four cor-
ners of the vehicle in particular, are
areas where objects do not always
appear in the bird’s-eye, front, or rear
views. Always check your surround-
ings to be sure that it is safe to move
before operating the vehicle. Always
operate the vehicle slowly.

•

The driver is always responsible for
safety during parking and other
maneuvers.

CAUTION

Do not scratch the camera lens when
cleaning dirt or snow from the front of
the camera.

The Intelligent Around View® Monitor sys-
tem is designed as an aid to the driver in
situations such as slot parking or parallel
parking.

The monitor displays various views of the
position of the vehicle in a split screen for-
mat. Not all views are available at all times.

Available views:

• Front View

A view of the front of the vehicle.

• Rear View

A view of the rear of the vehicle.

• Bird's-Eye View

The surrounding view of the vehicle from
above.

• Front-Side View

The view around and ahead of the front
passenger's side wheel.

• Front-Wide View

A wider area view of the front view.

• Rear-Wide View

A wider area view of the rear view.

To display the multiple views, the Intelligent
Around View® Monitor system uses cam-
eras located in the front grille, on the vehi-
cle’s outside mirrors and in the rear bum-
per

LHA5436

Monitor, climate, audio, phone and voice recognition systems

4-11

INTELLIGENT AROUND VIEW®
MONITOR SYSTEM OPERATION

With the ignition switch in the ON position,
move the shift lever to the R (Reverse) po-
sition or press the CAMERA button to oper-
ate the Intelligent Around View® Monitor.

When the camera is first activated with the
bird’s-eye view in the display, a red icon (if so
equipped) will flash on the screen. This in-
dicates that the sonar system is activated.
For additional information, see “Front and
Rear Sonar System” (P. 5-184).

Available views

WARNING

•

The distance guide lines and the ve-
hicle width lines should be used as a
reference only when the vehicle is on
a paved, level surface. The apparent
distance viewed on the monitor may
be different than the actual distance
between the vehicle and displayed
objects.

•

Use the displayed lines and the bird’s-
eye view as a reference. The lines and
the bird’s-eye view are greatly af-
fected by the number of occupants,
cargo, fuel level, vehicle position, road
condition and road grade.

•

If the tires are replaced with different
sized tires, the predicted course lines
and the bird's-eye view may be dis-
played incorrectly.

•

When driving the vehicle up a hill, ob-
jects viewed in the monitor are further
than they appear. When driving the ve-
hicle down a hill, objects viewed in the
monitor are closer than they appear.

•

Objects in the rear view will appear
visually opposite compared to when
viewed in the monitor and outside
mirrors.

•

Use the mirrors or actually look to
properly judge distances to other
objects.

•

On a snow-covered or slippery road,
there may be a difference between
the predicted course lines and the
actual course line.

•

The vehicle width and predicted
course lines are wider than the actual
width and course.

Front and rear view

Guiding lines that indicate the approximate
vehicle width and distance to objects with
reference to the vehicle body line

are

displayed on the monitor.

Distance guide lines

Indicate distances from the vehicle body:
• Red line

: approximately 1.5 ft (0.5 m)

• Yellow line

: approximately 3 ft (1 m)

• Green line

: approximately 7 ft (2 m)

• Green line

: approximately 10 ft (3 m)

(if so equipped)

LHA5437

Front view

4-12

Monitor, climate, audio, phone and voice recognition systems

Vehicle width guide lines

Indicate the approximate vehicle width
when backing up.

Predicted course lines

Indicate the predicted course when oper-
ating the vehicle. The predicted course
lines will be displayed on the monitor when
the steering wheel is turned. The predicted
course lines will move depending on how
much the steering wheel is turned and
might not be displayed while the steering
wheel is in the straight-ahead position.

The front view will not be displayed when
the vehicle speed is above 6 mph (10 km/h).

NOTE:

When the monitor displays the front
view and the steering wheel turns about
90 degrees or less from the straight-
ahead position, both the right and left
predicted course lines

are displayed.

When the steering wheel turns about 90
degrees or more, a line is displayed only
on the opposite side of the turn.

Bird’s-eye view

The bird's-eye view shows the overhead
view of the vehicle, which helps confirm the
vehicle position and the predicted course
to a parking space.

The vehicle icon

shows the position of

the vehicle. Note that the apparent dis-
tance between objects viewed in the
bird's-eye view may differ somewhat from
the actual distance to the vehicle.

The areas that the cameras cannot cover

(if so equipped) are indicated in black.

LHA5438

Rear view

LHA4534

Front view

Monitor, climate, audio, phone and voice recognition systems

4-13

The non-viewable area

(if so equipped)

is highlighted in yellow for several seconds
after the bird’s-eye view is displayed. It will
be shown only the first time after the igni-
tion switch is placed in the ON position.

In addition, the non-viewable corners are
displayed in red and blink for the first 3
seconds

to remind the driver to be

cautious.

Predicted course lines

indicate the pre-

dicted course when operating the vehicle.
The predicted course lines will be displayed
on the monitor when the steering wheel

is turned. The predicted course lines will
move depending on how much the steer-
ing wheel is turned and will not be dis-
played while the steering wheel is in the
neutral position.

When the monitor displays the front view
and the steering wheel turns about 90 de-
grees or less from the neutral position, the
two green predicted course lines are
shown in front of the vehicle.

When the steering wheel turns about 90
degrees or more, one green predicted
course line is shown in front of the vehicle
and the other predicted course line is
shown at the side of the vehicle.

When the monitor displays the rear view,
the predicted course lines are shown at the
back of the vehicle.

WARNING

•

Objects in the bird's-eye view will ap-
pear further than the actual distance.

•

Tall objects, such as a curb or vehicle,
may be misaligned or not displayed
at the seam of the views.

•

Objects that are above the camera
cannot be displayed.

•

The view of the bird's-eye view may
be misaligned when the camera po-
sition alters.

•

A line on the ground may be mis-
aligned and is not seen as being
straight at the seam of the views. The
misalignment will increase as the
line proceeds away from the vehicle.

LHA4535

Rear view

4-14

Monitor, climate, audio, phone and voice recognition systems

Front-side view

Guiding lines

Guiding lines that indicate the approximate
width and the front end of the vehicle are
displayed on the monitor.

The front-of-vehicle line

shows the front

part of the vehicle.

The side-of-vehicle line

shows the ap-

proximate vehicle width including the out-
side mirrors.

The extensions

of both the front

and

side

lines are shown with a green dotted

line.

Front-wide/Rear-wide view

While the front view/rear view shows a nor-
mal view on the split screens, the front-wide
view/rear-wide view shows a wider area on
the entire screen and allows checking of the
blind corners on the left and right sides..

Distance guide lines

Indicates distances from the vehicle body:
• Red line

: approximately 1.5 ft (0.5 m)

• Yellow line

: approximately 3 ft (1 m)

• Green line

: approximately 7 ft (2 m)

• Green line

: approximately 10 ft (3 m)

Vehicle width guide lines

Indicate the vehicle width when backing
up.

Predicted course lines

Indicate the predicted course when oper-
ating the vehicle. The predicted course
lines will move depending on how much
the steering wheel is turned. The predicted
course lines in the rear-wide view will not
be displayed while the steering wheel is in
the straight ahead position.

LHA2652

LHA5439

Front-wide view

LHA5440

Rear-wide view

Monitor, climate, audio, phone and voice recognition systems

4-15

The front-wide view will not be displayed
when the vehicle speed is above 6 mph
(10 km/h).

NOTE:

• When the monitor displays the front-wide

view and the steering wheel turns about
90 degrees or less from the straight
ahead position, both the right and left
predicted course lines

are displayed.

When the steering wheel is turns about
90 degrees or more, the predicted course
line is displayed only on the opposite side
of the turn.

DIFFERENCE BETWEEN PREDICTED
AND ACTUAL DISTANCES

Backing up on a steep uphill

Backing up on a steep downhill

LHA5441

LHA5442

4-16

Monitor, climate, audio, phone and voice recognition systems

Backing up near a projecting
object

The predicted course lines

do not touch

the object in the display. However, the ve-
hicle may hit the object if it projects over
the actual backing up course.

Backing up behind a projecting
object

The position

is shown farther than the

position

in the display. However, the po-

sition

is actually at the same distance as

the position

. The vehicle may hit the

object when backing up to the position

if the object projects over the actual back-
ing up course.

HOW TO PARK WITH PREDICTED
COURSE LINES

WARNING

•

If the tires are replaced with different
sized tires, the predicted course lines
may be displayed incorrectly.

•

On a snow-covered or slippery road,
there may be a difference between
the predicted course line and the ac-
tual course line.

•

If the battery is disconnected or be-
comes discharged, the predicted
course lines may be displayed incor-
rectly. If this occurs, please perform
the following procedures:

–

Turn the steering wheel from lock
to lock while the engine is running.

–

Drive the vehicle on a straight road
for more than 5 minutes.

•

When the steering wheel is turned
with the ignition switch in the ACC
position, the predicted course lines
may be displayed incorrectly.

LHA5443

LHA5444

Monitor, climate, audio, phone and voice recognition systems

4-17

1. Visually check that the parking space is

safe before parking your vehicle.

2. The rear view of the vehicle is displayed

on the screen

when the shift lever is

moved to the R (Reverse) position.

3. Slowly back up the vehicle adjusting the

steering wheel so that the predicted
course lines

enter the parking space

4. Maneuver the steering wheel to make

the vehicle width guide lines

parallel

to the parking space

while referring

to the predicted course lines.

5. When the vehicle is parked in the space

completely, move the shift lever to the P
(Park) position and apply the parking
brake.

HOW TO SWITCH THE DISPLAY

With the ignition switch in the ON position,
press the CAMERA button or move the shift
lever to the R (Reverse) position to operate
the Intelligent Around View® Monitor.

The Intelligent Around View® Monitor dis-
plays different split screen views depend-
ing on the position of the shift lever. Press
the CAMERA button to switch between the
available views.

If the shift lever is in the R (Reverse) position,
the available views are:
• Rear view/bird’s-eye view split screen
• Rear view/front-side view split screen
• Rear-wide view

LHA5445

LHA5446

4-18

Monitor, climate, audio, phone and voice recognition systems

If the shift lever is in the P (Park) or D (drive)
position, the available views are:
• Front view/bird’s-eye view split screen
• Front view/front-side view split screen
• Front-wide view

The display will switch from the Intelligent
Around View® Monitor screen when:
• The shift lever is in the D (Drive) position

and the vehicle speed increases above
approximately 6 mph (10 km/h)

• A different screen is selected.

OFF-ROAD MODE (for Rock
Creek®)

When the shift lever is out of the R (Reverse)
position, selecting the Drive Mode Selector
(SAND or MUD/RUT) affects the Intelligent
Around View® Monitor display as follows:

1. Selecting the Drive Mode Selector (SAND

or MUD/RUT) position will activate the
Intelligent Around View® Monitor. The
front view/front-side view split screen
will be displayed.

2. When the vehicle is shifted to the Drive

Mode Selector (SAND or MUD/RUT) posi-
tion with the bird’s-eye view displayed,
the passenger side of the display will
change to the front-side view.

When in the off-road mode, the Intelligent
Around View® Monitor will not return to the
previous screen.

The screen displayed on the Intelligent
Around View® Monitor will automatically
return to the previous screen 3 minutes
after the vehicle was shifted out of the
Drive Mode Selector (SAND or MUD/RUT)
position.

ADJUSTING THE SCREEN

1. Press the MENU button.

2. Touch the “Settings” key.

3. Touch the “Camera” key.

4. Touch the “Display Settings” key.

5. Touch the “Brightness”, “Contrast”, Tint”,

“Color”, or “Black Level” key.

6. Adjust the item by touching the “+” or “–”

key on the touch-screen display.

LHA5447

Monitor, climate, audio, phone and voice recognition systems

4-19

Nissan Pathfinder (2024 year). Manual in english - page 9