Nissan Pathfinder (2024 year). Manual in english

NOTE:

Do not adjust any of the display settings
of the Intelligent Around View® Monitor
while the vehicle is moving. Make sure
the parking brake is firmly applied.

INTELLIGENT AROUND VIEW®
MONITOR SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for Intelligent Around View® Monitor.
Failure to operate the vehicle in accor-
dance with these system limitations
could result in serious injury or death.

•

Do not use the Intelligent Around
View® Monitor with the outside mir-
rors in the stored position, and make
sure that the liftgate is securely
closed when operating the vehicle
using the Intelligent Around View®
Monitor.

•

The apparent distance between ob-
jects

viewed

the

Intelligent

Around View® Monitor differs from
the actual distance.

•

The cameras are installed on the
front grille, the outside mirrors and in
the rear bumper. Do not put anything
on

the

vehicle

that

covers

the

cameras.

•

When washing the vehicle with high
pressure water, be sure not to spray it
around the cameras. Otherwise, wa-
ter may enter the camera unit caus-
ing water condensation on the lens, a
malfunction, fire or an electric shock.

LHA5448

4-20

Monitor, climate, audio, phone and voice recognition systems

•

Do not strike the cameras. They are
precision

instruments.

Doing

could cause a malfunction or cause
damage resulting in a fire or an elec-
tric shock.

There are some areas where the system
will not show objects and the system does
not warn of moving objects. When in the
front or rear view display, an object below
the bumper or on the ground may not be
viewed

. When in the bird’s-eye view, a tall

object near the seam

of the camera

viewing areas will not appear in the
monitor.

The following are operating limitations and
do not represent a system malfunction:
• There may be a delay when switching

between views.

• When the temperature is extremely high

or low, the screen may not display objects
clearly.

• When strong light directly shines on the

camera, objects may not be displayed
clearly.

• The screen may flicker under fluorescent

light.

• The colors of objects on the Intelligent

Around View® Monitor may differ some-
what from the actual color of objects.

• Objects on the Intelligent Around View®

Monitor may not be clear and the color
of the object may differ in a dark
environment.

• There may be differences in sharpness

between each camera view of the bird's-
eye view.

• Do not use wax on the camera lens. Wipe

off any wax with a clean cloth that has
been dampened with a diluted mild
cleaning agent, then wipe with a dry
cloth.

System temporarily unavailable

When the “!” icon is displayed on the screen,
there are abnormal conditions in the Intel-
ligent Around View® Monitor. This will not
hinder normal driving operation but the
system should be inspected. It is recom-
mended that you visit a NISSAN dealer for
this service.

LHA5449

Monitor, climate, audio, phone and voice recognition systems

4-21

When the “[X]” icon is displayed on the
screen, the camera image may be receiv-
ing temporary electronic disturbances
from surrounding devices. This will not hin-
der normal driving operation but the sys-
tem should be inspected if it occurs fre-
quently. It is recommended that you visit a
NISSAN dealer for this service.

SYSTEM MAINTENANCE

CAUTION

•

Do not use alcohol, benzine or thin-
ner to clean the camera. This will
cause discoloration.

•

Do not damage the cameras as the
monitor screen may be adversely
affected.

If dirt, rain or snow accumulates on any of
the cameras

, the Intelligent Around

View® Monitor may not display objects
clearly. Clean the camera by wiping with a
cloth dampened with a diluted mild clean-
ing agent and then wiping with a dry cloth.

LHA5450

LHA5436

4-22

Monitor, climate, audio, phone and voice recognition systems

WARNING

Failure to follow the warnings and in-
structions for proper use of the sonar
function as outlined in this section
could result in serious injury or death.

•

The sonar is a convenience feature. It
is not a substitute for proper parking.

•

This function is designed as an aid to
the driver in detecting large station-
ary objects to help avoid damaging
the vehicle.

•

The driver is always responsible for
safety during parking and other
maneuvers.

•

Always look around and check that it
is safe to move before parking.

•

Read and understand the limitations
of the sonar as contained in this
section.

The sonar function helps to inform the
driver of large stationary objects around
the vehicle when parking by issuing an au-
dible and visual alert.

SONAR SYSTEM OPERATION

1. Center display

2. MENU button

3. CAMERA button

The system gives the tone for rear objects
when the shift lever is in the “R” (Reverse)
position.

When the camera image is shown on the
center display, the system shows the sonar
indicator regardless of the shift lever
position.

LHA5480

CAMERA AIDING SONAR (parking
sensor) (if so equipped)

Monitor, climate, audio, phone and voice recognition systems

4-23

The system is deactivated at speeds above
6 mph (10 km/h). It is reactivated at lower
speeds.

The colors of the sonar indicators and the
distance guide lines in the front and rear
views indicate different distances to the
object.

When the objects are detected, the indica-
tor (green) appears and blinks and the tone
sounds intermittently. When the vehicle
moves closer to the object, the color of the
indicator turns yellow and the rate of the
blinking and the rate of the tone increase.
When the vehicle is very close to the object,
the indicator stops blinking and turns red,
and the tone sounds continuously.

The intermittent tone will stop after 3 sec-
onds when an object is detected by only
the corner sonar and the distance does
not change.

The tone will stop when the object is no
longer near the vehicle.

TURNING ON AND OFF THE SONAR
FUNCTION

When the “Sonar” key is selected, the indi-
cator will turn off and the sonar will be
turned off temporarily. The Moving Object
Detection (MOD) system will also be turned
off at the same time. For additional infor-
mation, see “Moving Object Detection
(MOD)” (P. 4-26). When the “Sonar” key is se-
lected again, the indicator will turn on and
the sonar will turn back on.

In the below cases, the sonar will be turned
back on automatically:
• When the shift lever is placed in the “R”

(Reverse) position.

• When the CAMERA button is pressed and

a screen other than the camera view is
shown on the display.

• When vehicle speed decreases below ap-

proximately 6 mph (10 km/h).

• When the ignition switch is placed in the

“OFF” position and turned back to the “ON”
position again. To prevent the sonar sys-
tem from activating altogether, use the
“Camera” menu. For additional informa-
tion, see “Sonar function settings” (P. 4-24).

Sonar function settings

To set up the sonar function to your pre-
ferred settings, press the MENU button, se-
lect the “Settings” key, select the “Camera/
Sonar” key and then select the “Sonar” key
on the center display.

Designs and items displayed on the screen
may vary depending on the models.

Sonar:

When this item is turned on, the rear

sonar is activated. When this item is turned
off (indicator turns off), the rear sonar is
deactivated. The amber markers are dis-
played at the corners of the vehicle icon.
The next time the ignition switch is placed
in the ON position, “sonar is OFF” is dis-
played briefly.

Sonar Sensitivity:

Adjust the sensitivity

level of the sonar higher (right) or lower (left).

Sonar Volume:

Adjust the volume of the

buzzer.

Towing mode (if so equipped):

When this

item is turned on, only the rear sonar is off.
The amber markers are displayed at the rear
corners of the vehicle icon.

Show Camera when Sonar Activate (if so
equipped):

When this item is turned on, the

camera view is automatically shown on the
display in the case that the distance to the
objects measured by the sonar is becoming
short.

4-24

Monitor, climate, audio, phone and voice recognition systems

SONAR SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the sonar function. Failure to oper-
ate the vehicle in accordance with
these system limitations could result in
serious injury or death.

•

Inclement

weather

ultrasonic

sources such as an automatic car
wash,

truck’s

compressed-air

brakes or a pneumatic drill may af-
fect the function of the system, in-
cluding reduced performance or a
false activation.

•

The system is not designed to pre-
vent contact with small or moving
objects.

•

The system will not detect small ob-
jects below the bumper, and may not
detect objects close to the bumper or
on the ground.

•

The system may not detect the fol-
lowing objects:

–

Fluffy objects such as snow, cloth,

cotton, grass or wool.

–

Thin objects such as rope, wire or

chain.

–

Wedge-shaped objects.

•

If your vehicle sustains damage to
the bumper fascia, leaving it mis-
aligned or bent, the sensing zone
may be altered causing inaccurate
measurement of objects or false
alarms.

CAUTION

Excessive noise (such as audio system
volume or an open vehicle window) will
interfere with the tone and it may not
be heard.

System temporarily unavailable

When the amber markers are displayed at
the corners of the vehicle icon and the
function cannot be activated from the
Camera setting menu (the setting items
are grayed out), the sonar system may be
malfunctioning.

SYSTEM MAINTENANCE

CAUTION

Keep the surface of the sonar sensors
(located on the front and rear bumper
fascia) free from accumulations of
snow, ice and dirt. Do not scratch the
surface of the sonar sensors when
cleaning. If the sensors are covered, the
accuracy of the sonar function will be
diminished.

Monitor, climate, audio, phone and voice recognition systems

4-25

WARNING

•

Failure to follow the warnings and in-
structions for proper use of the Mov-
ing Object Detection system could
result in serious injury or death.

•

The MOD system is not a substitute
for proper vehicle operation and is
not designed to prevent contact with
objects

surrounding

the

vehicle.

When maneuvering, always use the
outside mirrors and rearview mirror
and turn and check the surroundings
to ensure it is safe to maneuver.

•

The system is deactivated at speeds
above 6 mph (10 km/h). It is reacti-
vated at lower speeds.

•

The MOD system is not designed to de-
tect surrounding stationary objects.

The MOD system can inform the driver of
moving objects near the vehicle when
backing out of garages, maneuvering in
parking lots and in other such instances.

The MOD system detects moving objects
by using image processing technology on
the image shown in the display.

MOD SYSTEM OPERATION

The MOD system will turn on automatically
under the following conditions:
• When the shift lever is in the R (Reverse)

position.

• When the CAMERA button is pressed to

activate the camera view on the display.

• When vehicle speed decreases below

approximately 6 mph (10 km/h) and the
camera screen is displayed.

The MOD system operates in the following
conditions when the camera view is
displayed:
• When the shift lever is in the P (Park) or N

(Neutral) position and the vehicle is
stopped, the MOD system detects mov-
ing objects in the bird’s-eye view. The
MOD system will not operate if the out-
side mirrors are moving in or out, in the
stowed position, or if either front door is
opened.

LHA5451

Front and bird’s-eye views

Monitor, climate, audio, phone and voice recognition systems

4-27

• When the shift lever is in the D (Drive)

position and the vehicle speed is below
approximately 6 mph (10 km/h), the MOD
system detects moving objects in the
front view.

• When the shift lever is in the R (Reverse)

position and the vehicle speed is below
approximately 6 mph (10 km/h), the MOD
system detects moving objects in the
rear view. The MOD system will not oper-
ate if the liftgate is open.

The MOD system does not detect moving
objects in the front-side view. The MOD
icon is not displayed on the screen when in
this view.

When the MOD system detects moving ob-
jects near the vehicle, a yellow frame will be
displayed on the view where the objects
are detected. While the MOD system con-
tinues to detect moving objects, the yellow
frame continues to be displayed.

NOTE:

While the RCTA chime is beeping, the
MOD system does not chime.

In the bird’s-eye view, the yellow frame

displayed on each camera image (front,
rear, right, left) depending on where mov-
ing objects are detected.

The yellow frame

is displayed on each

view in the front view and rear view modes.

A green MOD icon

is displayed in the

view where the MOD system is operative.
A gray MOD icon is displayed in the view
where the MOD system is not operative.

If the MOD system is turned off, the MOD
icon

is not displayed.

LHA5452

Rear and bird’s-eye views

LHA5453

Rear and front-side views

LHA5454

Front-wide view / Rear-wide View

4-28

Monitor, climate, audio, phone and voice recognition systems

TURNING MOD ON AND OFF

To turn the MOD system on or off:

1. Press the

button on the

steering wheel and select “Settings” in
the vehicle information display.

2. Using the scroll dial, select “Driver Assis-

tance” and press the OK button.

3. Select “Parking Aids”.

4. Toggle ON or OFF “Moving Object” using

the OK button.

MOD SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for MOD. Failure to operate the vehicle
in accordance with these system limi-
tations could result in serious injury or
death.

•

Do not use the MOD system when
towing a trailer. The system may not
function properly.

•

Excessive noise (for example, audio
system volume or open vehicle win-
dow) will interfere with the chime
sound, and it may not be heard.

•

The MOD system performance will be
limited according to environmental
conditions and surrounding objects
such as:

–

When there is low contrast be-

tween background and the mov-
ing objects.

–

When there is a blinking source of

light.

–

When strong light such as another

vehicle’s headlight or sunlight is
present.

–

When camera orientation is not in

its usual position, such as when a
mirror is folded.

–

When there is dirt, water drops or

snow on the camera lens.

–

When the position of the moving

objects in the display is not
changed.

•

The MOD system might detect flow-
ing water droplets on the camera
lens, white smoke from the muffler,
moving shadows, etc.

•

The MOD system may not function
properly depending on the speed, di-
rection, distance or shape of the
moving objects.

•

If your vehicle sustains damage to
the parts where the camera is in-
stalled, leaving it misaligned or bent,
the sensing zone may be altered and
the MOD system may not detect ob-
jects properly.

•

When the temperature is extremely
high or low, the screen may not dis-
play objects clearly. This is not a
malfunction.

Monitor, climate, audio, phone and voice recognition systems

4-29

NOTE:
The green MOD icon will change to or-
ange if one of the following has oc-
curred:

•

When the system is malfunctioning.

•

When the component temperature
reaches a high level (icon will blink).

•

When the rearview camera has de-
tected a blockage (icon will blink).

If the icon light continues to illuminate
orange, have the MOD system checked. It
is recommended that you visit a NISSAN
dealer for this service.

SYSTEM MAINTENANCE

CAUTION

•

Do not use alcohol, benzine or thin-
ner to clean the camera. This will
cause discoloration.

•

Do not damage the camera as the
monitor screen may be adversely
affected.

If dirt, rain or snow accumulates on any of
the cameras

, the MOD system may not

operate properly. Clean the camera by wip-
ing with a cloth dampened with a diluted
mild cleaning agent and then wiping with a
dry cloth.

LHA5436

4-30

Monitor, climate, audio, phone and voice recognition systems

Adjust air flow direction for the center vents

, driver’s and passenger's side vents

and rear passenger compartment vents

by moving the vent slide and/or vent

assemblies.

Open or close the vents using the dial.

LHA5427

VENTS

Monitor, climate, audio, phone and voice recognition systems

4-31

Heated seat switches (if so

equipped)

AUTO (automatic) climate control
button/ temperature control dial
(driver's side)

Display screen

REAR ON-OFF button

REAR CTRL (rear climate display screen)
button

REAR LOCK button (if so equipped)

Heated steering wheel switch

(if so equipped)

SYNC button/ temperature control dial
(passenger's side)

Climate controlled seat switches

(if so equipped)

10.

A/C (air conditioner) button

11.

REAR window and outside mirror

(if so equipped) defroster switch

12.

Front defroster button

13.

Air flow control button

14.

Fan speed control buttons

15.

Fresh air intake button

16.

Air recirculation button

17.

ON-OFF button

WARNING

•

The air conditioner cooling function
operates only when the engine is
running.

•

Do not leave children or adults who
would normally require the assis-
tance of others alone in your vehicle.
Pets should also not be left alone.
They could accidentally injure them-
selves or others through inadvertent
operation of the vehicle. Also, on hot,
sunny days, temperatures in a closed
vehicle could quickly become high
enough to cause severe or possibly
fatal injuries to people or animals.

•

Do not use the recirculation mode for
long periods as it may cause the inte-
rior air to become stale and the win-
dows to fog up.

LHA5723

HEATER AND AIR CONDITIONER
(automatic)

4-32

Monitor, climate, audio, phone and voice recognition systems

Start the engine and operate the controls
to activate the air conditioner.

NOTE:
• Odors from inside and outside the ve-

hicle can build up in the air conditioner
unit. Odor can enter the passenger
compartment through the vents.

• When parking, set the heater and air

conditioner controls to turn off air re-
circulation to allow fresh air into the
passenger compartment. This should
help reduce odors inside the vehicle.

While the engine is stopped by the Idling
Stop System, activating the front defroster
will cause the engine to automatically re-
start. While the engine is running, activating
the front defroster will prevent the Idling
Stop System from automatically stopping
the engine.

When the engine is stopped by the Idling
Stop System, heater and air conditioner
performance may be reduced. To keep full
heater and air conditioner performance,
restart the engine by pushing the Idling
Stop OFF switch. For additional informa-
tion, see “Idling Stop System” (P. 5-190).

AUTOMATIC OPERATION

Cooling and/or dehumidified
heating (AUTO)

This mode may be used all year round as
the system automatically works to keep a
constant temperature. Air flow distribution,
air intake control, and fan speed are also
controlled automatically.

1. Press the AUTO button.

2. Turn the temperature control dial to

the left or right to set the desired
temperature.

• Adjust the temperature display to about

75°F (24°C) for normal operation.

• The temperature of the passenger com-

partment will be maintained automati-
cally. Air flow distribution, air intake con-
trol and fan speed are also controlled
automatically.

• A visible mist may be seen coming from

the vents in hot, humid conditions as the
air is cooled rapidly. This does not indicate
a malfunction.

3. You can individually set driver's and front

passenger's side temperature using
each temperature control dial.

• To synchronize the driver’s and front pas-

senger’s temperature settings, press the
SYNC button. The SYNC indicator will
illuminate.

Heating (A/C off)

The air conditioner does not activate. When
you need to heat only, use this mode.

1. Press the AUTO button.

2. Turn the temperature control dial to set

the desired temperature.

• The temperature of the passenger com-

partment will be maintained automati-
cally. Air flow distribution, air intake con-
trol and fan speed are also controlled
automatically.

• Not recommended if windows fog up.

Dehumidified defrosting or
defogging

1. Press the

front defroster button.

(The indicator light on the button will
come on.)

2. Turn the temperature control dial to set

the desired temperature.

Monitor, climate, audio, phone and voice recognition systems

4-33

• To quickly remove ice from the outside of

the windows, use the

fan speed con-

trol buttons to set the fan speed to
maximum.

• As soon as possible after the windshield

is clean, press the AUTO button to return
to the automatic mode.

• When the

front defroster button is

pressed, the air conditioner will automati-
cally be turned on at outside tempera-
tures above 36°F (2°C). The air recirculate
mode automatically turns off, allowing
outside air to be drawn into the passen-
ger compartment to further improve the
defogging performance.

Remote Engine Start with
Intelligent Climate Control (if so
equipped)

Vehicles equipped with automatic climate
controls and Remote Engine Start function
may go into automatic heating or cooling
mode when Remote Engine Start is acti-
vated depending on outside and cabin
temperatures. During this period, the cli-
mate control display and buttons will be
inoperable until the ignition switch is
placed in the ON position. In Remote En-
gine Start defrosting mode, the rear win-

dow

defroster,

heated

seats

(if

equipped) and heated steering wheel (if so
equipped) may be activated automatically.

Voice Recognition logic (if so
equipped)

When the climate control system is on, the
front and rear fan speeds may be auto-
matically lowered so that commands are
more easily recognized. Fan speed can be
adjusted using the fan speed decrease and
increase buttons, if desired.

MANUAL OPERATION

Fan speed control

Press the

fan speed control buttons

to manually control the fan speed.

Press the AUTO button to return to auto-
matic control of the fan speed.

Temperature control dial

The temperature control dial allows you to
adjust the temperature of the outlet air. To
lower the temperature, turn the dial to the
left. To increase the temperature, turn the
dial to the right. Temperature can be ad-
justed on the driver’s and passenger’s side.

Air recirculation

Press the

air recirculation button to

recirculate interior air inside the vehicle.
The

indicator light on the button will

come on.

The air recirculation cannot be activated
when the air conditioner is in the

front

defrosting mode.

When the outside temperature exceeds
70°F (21°C), the air conditioning system may
default to air recirculation mode automati-
cally to reduce overall power consumption.
To exit air recirculation mode, deselect the
air recirculation button (indicator will turn
off) to enter fresh air mode.

Fresh air intake

Press the

fresh air intake button to

draw outside air into the passenger
compartment.

A/C (air conditioner) button

Start the engine, press the

fan speed

control buttons to the desired position and
press the

button to turn on the air

conditioner. To turn off the air conditioner,
press the

button again.

The air conditioner cooling function op-
erates only when the engine is running.

4-34

Monitor, climate, audio, phone and voice recognition systems

Air flow control

Pressing the

air flow control button

manually controls air flow and selects the
air outlet:

—

Air flows from center and side
vents.

—

Air flows from center and side
vents and foot outlets.

—

Air flows mainly from foot out-
lets.

—

Air flows from defroster and foot
outlets.

Synchronize climate settings

Press the SYNC button to synchronize cli-
mate settings. The sync indicator will turn
on.

When rear climate is off, pressing SYNC will
synchronize only driver's and front passen-
ger's climate settings. When rear climate is
on, pressing SYNC will synchronize driver,
front passenger, and rear temperature
mode and auto fan settings.

SYNC text will appear above the rear tem-
perature display when rear climate is syn-
chronized with the driver’s settings.

To change climate settings when SYNC is
active (the SYNC indicator is on):
• The driver's side temperature control dial

will control the driver, front passenger,
and rear (if rear climate is on) tempera-
tures.

• The fan speed control buttons will control

the front and rear climate fan speeds.

• The front AUTO (automatic) climate con-

trol ON-OFF button will activate the front
and rear climate automatic settings.

• The air flow control button will control the

front and rear airflow direction.

To exit SYNC:
• To remove the front passenger from

SYNC, turn the passenger's side tem-
perature control dial. The driver and rear
settings remain in SYNC until rear is re-
moved from SYNC.

• To remove the rear from SYNC, change

any of the rear climate settings. The
driver and front passenger settings re-
main in SYNC until the front passenger is
removed from SYNC.

• To reactivate SYNC, press the SYNC

button.

To turn system off

Press the ON-OFF button to turn the sys-
tem off.

To turn system on

Press the ON-OFF button when the heater
or air conditioner is off. The system will turn
on with the settings that were used imme-
diately before the system was turned off.

Rear window and outside mirror
(if so equipped) defroster switch

For additional information, see “Rear win-
dow and outside mirror (if so equipped)
defroster switch” (P. 2-84).

Heated seat switches (if so
equipped)

For additional information, see “Heated
seat switches” (P. 2-94).

Heated steering wheel switch (if
so equipped)

For additional information, see “Heated
steering wheel switch” (P. 2-96).

Monitor, climate, audio, phone and voice recognition systems

4-35

Climate controlled seat switches
(if so equipped)

For additional information, see “Climate
controlled seat switches” (P. 2-93).

OPERATING TIPS

The sunload sensor, located on the top
driver's side of the instrument panel, helps
the system maintain a constant tempera-
ture. Do not put anything on or around this
sensor.
• When the climate system is in automatic

operation and the engine coolant tem-
perature and outside air temperature are
low, the air flow outlet may default to de-
froster mode for a maximum of 2 minutes
30 seconds. This is not a malfunction. After
the engine coolant temperature warms up,
the air flow outlet will return to foot mode
and operation will continue normally.

• When the outside and interior cabin tem-

peratures are moderate to high, the in-
take setting may default to turn off air
recirculation to allow fresh air into the
passenger compartment. You may no-
tice air flow from the foot mode, bi-level
mode or side demist vent outlets for a
maximum of 15 seconds. This may occur
when the previous climate setting was
turned off. This is not a malfunction. After
the initial warm air is expelled, the intake
will return to automatic control, the air
flow outlet will return to previous settings,
and operation will continue normally. To
exit, press any climate control button.

• Keep the moonroof (if so equipped)

closed while the air conditioner is in
operation.

• If you feel that the air flow mode you have

selected and the outlets the air is coming
out do not match, select the

mode.

• When you change the air flow mode, you

may feel air flow from the foot outlets for
just a moment. This is not a malfunction.

LHA5465

4-36

Monitor, climate, audio, phone and voice recognition systems

REAR AUTOMATIC AIR
CONDITIONING SYSTEM

1. AUTO button/ temperature control dial

(driver’s side)

2. Display screen

3. REAR ON-OFF button

4. REAR CTRL button

5. REAR LOCK button (if so equipped)

6. SYNC button/ temperature control dial

(passenger’s side)

7. A/C (air conditioner) button

Fan speed control buttons

9. ON-OFF button

To turn on the rear automatic air condition-
ing system with the front air conditioner
control panel, press the REAR ON-OFF
button.

The rear automatic air conditioning sys-
tem can be adjusted with the front air con-
ditioner control panel by pressing the REAR
CTRL button.

The front climate display will switch to the
REAR climate screen.

To adjust the front air conditioning system,
press the REAR CTRL button

Automatic operation

1. Press the AUTO button. The AUTO indica-

tor button will illuminate.

2. Turn the temperature control dials to set

desired temperature.

Manual operation

•

Temperature control

Turn the temperature control dial to set
the desired temperature.

LHA5707

Front Controls

Monitor, climate, audio, phone and voice recognition systems

4-37

•

Fan speed control

Press the

Fan speed control buttons

to manually control the fan speed.

Rear Heating

1. Press the AUTO button. The AUTO indica-

tor button will illuminate on the front
display.

2. Turn the temperature control dial to set

the desired temperature.

Turning the system off

• Press the REAR ON-OFF button on the

front display to turn the rear climate sys-
tem off. The indicator light will turn off.

• Press the ON-OFF button. The rear cli-

mate will turn off and the control will
switch to front climate.

Locking the REAR controls

1. Press the REAR LOCK button on the front

climate control panel. LOCK will be dis-
played on the rear climate display
screen.

2. The rear climate controls will be locked

and can only be adjusted using the front
controls.

Rear control buttons (if so equipped)

Fan speed control buttons

2. Display screen

3. Temperature control buttons

Heated 2nd row seat switches (if so

equipped)

5. ON-OFF button

6. Air flow control buttons

7. AUTO button

The rear seat passengers can adjust the
rear automatic air conditioning system us-
ing the control buttons at the rear of the
center console.

The rear control buttons do not function
when the REAR LOCK button is on.
•

Fan speed control buttons

adjusts

the rear fan speed up or down.

•

Temperature

increase

and

decrease buttons

adjusts the rear

temperature up or down.

LHA5474

Rear Controls

4-38

Monitor, climate, audio, phone and voice recognition systems

•

Heated 2nd row seat switches (if so
equipped)

For additional information,

see “Heated 2nd row seat switches”
(P. 2-95).

•

ON-OFF button

Turns rear automatic air

conditioning system on and off.

•

Air flow control buttons

controls air flow

and selects the air outlet.

•

AUTO button

Turns rear automatic air

conditioning system on, AUTO mode on.

The air conditioner system in your NISSAN
vehicle is charged with a refrigerant de-
signed with the environment in mind.

This refrigerant does not harm the
earth's ozone layer.

Special charging equipment and lubricant
is required when servicing your NISSAN air
conditioner. Using improper refrigerants or
lubricants will cause severe damage to
your air conditioner system. For additional
information, see “Air conditioner system
refrigerant

and

oil

recommendations”

(P. 10-8).

It is recommended that you visit a NISSAN
dealer to service your “environmentally
friendly” air conditioner system.

WARNING

The air conditioner system contains re-
frigerant under high pressure. To avoid
personal injury, any air conditioner
service should be done only by an
experienced technician with proper
equipment.

ROOF MOUNTED ANTENNA

The antenna is located on the rear part of
the vehicle roof.

CAUTION

•

A build-up of ice on the antenna can
affect radio performance. Remove
the ice to restore radio reception.

•

When removing snow from the roof,
do not apply strong force to the an-
tenna. That may cause broken an-
tenna and roof panel dent.

•

When using a high pressure car wash,
keep the high pressure nozzle away
from the antenna. The seal may be
deformed or damaged.

•

The radio performance may be af-
fected if cargo carried on the roof
blocks the radio signal. If possible, do
not put cargo near the antenna.

SERVICING AIR CONDITIONER

ANTENNA

Monitor, climate, audio, phone and voice recognition systems

4-39

When installing a CB, ham radio or car
phone in your vehicle, be sure to observe
the following precautions; otherwise, the
new equipment may adversely affect the
engine control system and other electronic
parts.

WARNING

•

A cellular phone should not be used
for any purpose while driving so full
attention may be given to vehicle op-
eration. Some jurisdictions prohibit
the use of cellular phones while
driving.

•

If you must make a call while your
vehicle is in motion, the hands free
cellular phone operational mode is
highly recommended. Exercise ex-
treme caution at all times so full
attention may be given to vehicle
operation.

•

If you are unable to devote full atten-
tion to vehicle operation while talk-
ing on the phone, pull off the road to
a safe location and stop your vehicle.

CAUTION

•

Keep the antenna as far away as pos-
sible from the electronic control
modules.

•

Keep the antenna wire more than 8 in
(20 cm) away from the electronic
control system harnesses. Do not
route the antenna wire next to any
harness.

•

Adjust the antenna standing-wave
ratio as recommended by the manu-
facturer.

•

Connect the ground wire from the CB
radio chassis to the body.

•

For additional information, it is rec-
ommended that you visit a NISSAN
dealer for servicing.

“Made for iPod”, “Made for iPhone” and
“Made for iPad” mean that an electronic
accessory has been designed to connect
specifically to iPod, iPhone or iPad, respec-
tively, and has been certified by the devel-
oper to meet Apple performance stan-
dards. Apple is not responsible for the
operation of this device or its compliance
with safety and regulatory standards.
Please note that the use of this accessory
with iPod, iPhone or iPad may affect wire-
less performance.

iPad, iPhone, iPod classic, iPod nano, iPod
shuffle and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other
countries. Lightning is a trademark of
Apple Inc.

CAR PHONE OR CB RADIO

iPod®/iPhone®

4-40

Monitor, climate, audio, phone and voice recognition systems

WARNING

•

Properly secure all cargo with ropes
or straps to help prevent it from slid-
ing or shifting. Do not place cargo
higher than the seatbacks. In a sud-
den stop or collision, unsecured
cargo could cause personal injury.

EXHAUST GAS (carbon monoxide)

WARNING

•

Do not breathe exhaust gases; they
contain colorless and odorless car-
bon monoxide. Carbon monoxide is
dangerous. It

can

cause

uncon-

sciousness or death.

•

If you suspect that exhaust fumes
are entering the vehicle, drive with all
windows fully open, and have the ve-
hicle inspected immediately.

•

Do not run the engine in closed
spaces such as a garage.

•

Do not park the vehicle with the en-
gine running for any extended length
of time.

•

Keep the rear vent windows, lift-
gates, doors and trunk lids (if so
equipped) closed while driving, oth-
erwise

exhaust

gases

could

drawn into the passenger compart-
ment. If you must drive with one of
these open, follow these precau-
tions:

1. Open all the windows.
2. Set the

air recirculation but-

ton to off and the fan control dial
to high to circulate the air.

•

If electrical wiring or other cable con-
nections must pass to a trailer
through the seal on the liftgate or the
body, follow the manufacturer's rec-
ommendation to prevent carbon
monoxide entry into the vehicle.

•

The exhaust system and body should
be inspected by a qualified mechanic
whenever:

a. The vehicle is raised for service.
b. You suspect that exhaust fumes

are entering into the passenger
compartment.

c. You notice a change in the sound

of the exhaust system.

d. You have had an accident involving

damage to the exhaust system, un-
derbody, or rear of the vehicle.

THREE-WAY CATALYST

The three-way catalyst is an emission con-
trol device installed in the exhaust system.
Exhaust gases in the three-way catalyst
are burned at high temperatures to help
reduce pollutants.

WARNING

•

The exhaust gas and the exhaust sys-
tem are very hot. Keep people, animals
or flammable materials away from the
exhaust system components.

•

Do not stop or park the vehicle over
flammable materials such as dry
grass, waste paper or rags. They may
ignite and cause a fire.

PRECAUTIONS WHEN STARTING AND
DRIVING

5-4

Starting and driving

CAUTION

•

Do not use leaded gasoline. Deposits
from leaded gasoline will seriously
reduce the three-way catalyst's abil-
ity to help reduce exhaust pollutants.

•

Keep your engine tuned up. Malfunc-
tions in the ignition, fuel injection, or
electrical systems can cause overrich
fuel flow into the three-way catalyst,
causing it to overheat. Do not keep
driving if the engine misfires, or if no-
ticeable loss of performance or other
unusual operating conditions are de-
tected. Have the vehicle inspected
promptly. It is recommended that
you visit a NISSAN dealer for this
service.

•

Avoid driving with an extremely low
fuel level. Running out of fuel could
cause the engine to misfire, damag-
ing the three-way catalyst.

•

Do not race the engine while warm-
ing it up.

•

Do not push or tow your vehicle to
start the engine.

TIRE PRESSURE MONITORING
SYSTEM (TPMS)

Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recom-
mended by the vehicle manufacturer on
the vehicle placard or tire inflation pressure
label. (If your vehicle has tires of a different
size than the size indicated on the vehicle
placard or tire inflation pressure label, you
should determine the proper tire inflation
pressure for those tires.)

As an added safety feature, your vehicle
has been equipped with a Tire Pressure
Monitoring System (TPMS) that illuminates
a low tire pressure telltale when one or
more of your tires is significantly under-
inflated. Accordingly, when the low tire
pressure telltale illuminates, you should
stop and check all your tires as soon as
possible, and inflate them to the proper
pressure. Driving on a significantly under-
inflated tire causes the tire to overheat and
can lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and
stopping ability.

Please note that the TPMS is not a substi-
tute for proper tire maintenance, and it is
the driver’s responsibility to maintain cor-
rect tire pressure, even if under-inflation
has not reached the level to trigger illumi-
nation of the TPMS low tire pressure telltale.

Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate
when the system is not operating properly.
The TPMS malfunction indicator is com-
bined with the low tire pressure telltale.
When the system detects a malfunction,
the telltale will flash for approximately one
minute and then remain continuously illu-
minated. This sequence will continue upon
subsequent vehicle start-ups as long as
the malfunction exists. When the malfunc-
tion indicator is illuminated, the system
may not be able to detect or signal low tire
pressure as intended. TPMS malfunctions
may occur for a variety of reasons, includ-
ing the installation of replacement or alter-
nate tires or wheels on the vehicle that
prevent the TPMS from functioning prop-
erly. Always check the TPMS malfunction
telltale after replacing one or more tires or
wheels on your vehicle to ensure that the
replacement or alternate tires and wheels
allow the TPMS to continue to function
properly.

Starting and driving

5-5

Additional information:

• When using a wheel without the TPMS

such as the spare tire, the TPMS does not
monitor the tire pressure of the spare tire.

• The TPMS will activate only when the ve-

hicle is driven at speeds above 16 mph (25
km/h). Also, this system may not detect a
sudden drop in tire pressure (for example,
a flat tire while driving).

• The low tire pressure warning light does

not automatically turn off when the tire
pressure is adjusted. After the tire is in-
flated to the recommended pressure, the
vehicle must be driven at speeds above
16 mph (25 km/h) to activate the TPMS
and turn off the low tire pressure warning
light. Use a tire pressure gauge to check
the tire pressure.

• The “Tire Pressure Low - Add Air” warning

appears in the vehicle information dis-
play when the low tire pressure warning
light is illuminated and low tire pressure is
detected. The “Tire Pressure Low - Add
Air” warning turns off when the low tire
pressure warning light turns off.

• The “Tire Pressure Low - Add Air” warning

appears each time the ignition switch is
placed in the ON position as long as the
low tire pressure warning light remains
illuminated.

• The “Tire Pressure Low - Add Air” warning

does not appear if the low tire pressure
warning light illuminates to indicate a
TPMS malfunction.

• Tire pressure rises and falls depending on

the heat caused by the vehicle’s opera-
tion and the outside temperature. Do not
reduce the tire pressure after driving be-
cause the tire pressure rises after driving.
Low outside temperature can lower the
temperature of the air inside the tire
which can cause a lower tire inflation
pressure. This may cause the low tire
pressure warning light to illuminate. If the
warning light illuminates, check the tire
pressure for all four tires.

• The Tire and Loading Information label is

located in the driver's door opening.

• You can also check the pressure of all

tires (except the spare tire) on the vehicle
information display screen. The order of
the tire pressure figures displayed on the
screen corresponds with the actual order
of the tire position.

For additional information, see “Low tire
pressure warning light” (P. 2-19) and “Tire
Pressure Monitoring System (TPMS)” (P. 6-3).

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

•

If the low tire pressure warning light
illuminates while driving, avoid sud-
den steering maneuvers or abrupt
braking, reduce vehicle speed, pull
off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and
increase the likelihood of tire failure.
Serious vehicle damage could occur
and may lead to an accident and
could result in serious personal in-
jury. Check the tire pressure for all
four tires. Adjust the tire pressure to
the recommended COLD tire pres-
sure shown on the Tire and Loading
Information label to turn the low tire
pressure warning light off. If you have
a flat tire, replace it with a spare tire
as soon as possible. For additional
information, see “Flat tire” (P. 6-3).

5-6

Starting and driving

•

When using a wheel without the
TPMS such as the spare tire, when a
spare tire is mounted or a wheel is
replaced, tire pressure will not be in-
dicated, the TPMS will not function
and the low tire pressure warning
light will flash for approximately 1
minute. The light will remain on after
1 minute. Have your tires replaced
and/or TPMS system reset as soon as
possible. It is recommended that you
visit a NISSAN dealer for this service.

•

Replacing tires with those not origi-
nally specified by NISSAN could af-
fect the proper operation of the
TPMS.

•

Do not inject any tire liquid or aerosol
tire sealant into the tires, as this may
cause a malfunction of the tire pres-
sure sensors.

CAUTION

•

The TPMS may not function properly
when the wheels are equipped with
tire chains or the wheels are buried in
snow.

•

Do not place metalized film or any
metal parts (antenna, etc.) on the
windows. This may cause poor re-
ception of the signals from the tire
pressure sensors, and the TPMS will
not function properly.

Some devices and transmitters may tem-
porarily interfere with the operation of the
TPMS and cause the low tire pressure
warning light to illuminate.

Some examples are:
• Facilities or electric devices using similar

radio frequencies are near the vehicle.

• If a transmitter set to similar frequencies

is being used in or near the vehicle.

• If a computer (or similar equipment) or a

DC/AC converter is being used in or near
the vehicle.

The low tire pressure warning light may
illuminate in the following cases.
• If the vehicle is equipped with a wheel and

tire without TPMS.

• If the TPMS has been replaced and the ID

has not been registered.

• If the wheel is not originally specified by

NISSAN.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's au-
thority to operate the equipment.

For Canada:

This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause un-
desired operation of the device.

Starting and driving

5-7

TPMS with Easy-Fill Tire Alert

When adding air to an under-inflated tire,
the TPMS with Easy-Fill Tire Alert provides
visual and audible signals outside the ve-
hicle to help you inflate the tires to the rec-
ommended COLD tire pressure.

Vehicle set-up

1. Park the vehicle in a safe and level place.

2. Apply the parking brake and press the

park button to shift to the P (Park)
position.

3. Place the ignition switch in the ON posi-

tion. Do not start the engine.

Operation

1. Add air to the tire.

2. After a few seconds, the hazard indica-

tors will start flashing.

3. When

the

designated

pressure

reached, the horn beeps once and the
hazard indicators stop flashing.

4. Perform the above steps for each tire.

• If the tire is over-inflated more than

approximately 4 psi (30 kPa), the horn
beeps and the hazard indicators flash
three times. To correct the pressure,
push the core of the valve stem on the

tire briefly to release pressure. When
the pressure reaches the designated
pressure, the horn beeps once.

• If the hazard indicator does not flash

within approximately 15 seconds after
starting to inflate the tire, it indicates
that the Easy-Fill Tire Alert is not
operating.

• The TPMS will not activate the Easy-Fill

Tire

Alert

under

the

following

conditions:

– If there is interference from an exter-

nal device or transmitter.

– The air pressure from the inflation

device is not sufficient to inflate the
tire.

– There is a malfunction in the TPMS.
– There is a malfunction in the horn or

hazard indicators.

– The identification code of the tire

pressure sensor is not registered to
the system.

– The battery of the tire pressure sen-

sor is low.

• If the Easy-Fill Tire Alert does not oper-

ate due to TPMS interference, move
the vehicle about 3 ft (1 m) backward
or forward and try again.

If the Easy-Fill Tire Alert is not working, use a
tire pressure gauge.

ON-PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS

Utility

vehicles

have

significantly

higher rollover rate than other types of
vehicles.

They have higher ground clearance than
passenger cars to make them capable of
performing in a variety of on-pavement
and off-road applications. This gives them
a higher center of gravity than ordinary ve-
hicles. An advantage of higher ground
clearance is a better view of the road, allow-
ing you to anticipate problems. However,
they are not designed for cornering at the
same speeds as conventional 2-Wheel
Drive vehicles any more than low-slung
sports cars are designed to perform satis-
factorily under off-road conditions. If at all
possible, avoid sharp turns at high speeds.
As with other vehicles of this type, failure to
operate this vehicle correctly may result in
loss of control or vehicle rollover.

In a rollover crash, an unbelted person is
significantly more likely to die than a per-
son wearing a seat belt.

For additional information, see “Driving
safety precautions” (P. 5-10) .

5-8

Starting and driving

AVOIDING COLLISION AND
ROLLOVER

WARNING

Failure to operate this vehicle in a safe
and prudent manner may result in loss
of control or an accident.

Be alert and drive defensively at all times.
Obey all traffic regulations. Avoid excessive
speed, high speed cornering, or sudden
steering maneuvers, because these driving
practices could cause you to lose control of
your vehicle.

As with any vehicle, loss of control could
result in a collision with other vehicles or
objects or cause the vehicle to roll over,
particularly if the loss of control causes
the vehicle to slide sideways.

Be attentive at all times, and avoid driving
when tired. Never drive when under the in-
fluence of alcohol or drugs (including pre-
scription or over-the-counter drugs which
may cause drowsiness). Always wear your
seat belt as outlined in the “Safety – Seats,
seat belts and supplemental restraint sys-
tem” section of this manual, and also in-
struct your passengers to do so.

Seat belts help reduce the risk of injury in
collisions and rollovers.

In a rollover crash, an unbelted person is
significantly more likely to die than a
person wearing a seat belt.

OFF-ROAD RECOVERY

While driving, the right side or left side
wheels may unintentionally leave the road
surface. If this occurs, maintain control of
the vehicle by following the procedure be-
low. Please note that this procedure is only
a general guide. The vehicle must be driven
as appropriate based on the conditions of
the vehicle, road and traffic.

1. Remain calm and do not overreact.

2. Do not apply the brakes.

3. Maintain a firm grip on the steering

wheel with both hands and try to hold a
straight course.

4. When appropriate, slowly release the ac-

celerator pedal to gradually slow the
vehicle.

5. If there is nothing in the way, steer the

vehicle to follow the road while vehicle
speed is reduced. Do not attempt to
drive the vehicle back onto the road sur-
face until vehicle speed is reduced.

6. When it is safe to do so, gradually turn

the steering wheel until both tires return
to the road surface. When all tires are on
the road surface, steer the vehicle to
stay in the appropriate driving lane.

• If you decide that it is not safe to return

the vehicle to the road surface based
on vehicle, road or traffic conditions,
gradually slow the vehicle to a stop in
a safe place off the road.

RAPID AIR PRESSURE LOSS

Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged
due to hitting a curb or pothole. Rapid air
pressure loss can also be caused by driving
on under-inflated tires.

Rapid air pressure loss can affect the han-
dling and stability of the vehicle, especially
at highway speeds.

Help prevent rapid air pressure loss by
maintaining the correct air pressure and
visually inspecting the tires for wear and
damage. For additional information, see
“Wheels and tires” (P. 8-29). If a tire rapidly
loses air pressure or “blows-out” while driv-
ing, maintain control of the vehicle by fol-
lowing the procedure below. Please note
that this procedure is only a general guide.

Starting and driving

5-9

Nissan Pathfinder (2024 year). Manual in english - page 10