Nissan Pathfinder (2024 year). Manual in english

–– Speed Limit Sign
–– Audio
–– TEL/SMS

• Reset

NOTE:
• Emergency information may display

even if the HUD is turned off.

• If the HUD is turned off, the settings

items are grayed out and cannot be
modified until the HUD is turned back
on.

This product includes the following soft-
ware.

(1) Panasonic Corporation or software de-
veloped for Panasonic Corporation

(2) Third-party software licensed to Pana-
sonic Corporation

(3) Open source software

Regarding (3) Open source software, it in-
cludes open source software (OSS), includ-
ing various software to which license infor-
mation applies.

Refer to the license web site at:
http://car.panasonic.jp/oss/i02lln39.

DRIVER ASSISTANCE/NAVIGATION
LINKING

The HUD will display driver assistance and
navigation information.

The driver assistance display will show
warning situations for the following sys-
tems:
• Automatic Emergency Braking (AEB) with

Pedestrian Detection

• Lane Departure Warning (LDW)
• Intelligent

Forward

Collision

Warning

(IFCW)

• Hands-free warning (for vehicles with

ProPILOT Assist) (if so equipped)

• Traffic Sign Recognition (TSR) (if so

equipped)

The navigation system linking display will
show the following items:
• Intersection names
• Arrows indicating turning direction
• Distance to the next intersection

The Audio System linking display will show
the following items:
• Songs
• Radio stations

The TEL/SMS linking display will show the
following items:
• Caller’s name or phone number

2-100

Instruments and controls

Display brightness

The brightness of the display may be con-
trolled by the navigation system. The
brightness will also be adjusted automati-
cally according to the exterior ambient
lighting brightness.

NOTE:
• The HUD has a built-in sensor

that

controls the brightness of the dis-
played image. If you block the sensor
with an object, the display will darken,
making it difficult to see.

• Do not apply strong light to the sensor

of the Head-Up Display. Doing so may
cause a malfunction.

EMERGENCY SUPPORT

NissanConnect® Services provide various
services to support dealing with emergen-
cies of the subscribed vehicle and the
driver.

For example, in case of an illness or serious
injury, you can seek support by pressing the
in-vehicle Emergency Call (SOS) button and
connecting to the NissanConnect® Services
Response Center. The NissanConnect® Ser-
vices Response Center can specify the lo-
cation of the vehicle via GPS, and the infor-
mation will be sent to the police or other
agencies as needed.

For information about other NissanConnect®
Services emergency support related ser-
vices, contact the NissanConnect® Customer
Support line at 1–855–426–6628 or refer
to the NissanConnect® Services website
www.nissanusa.com/connect (for U.S.) or
www.nissan.ca/nissanconnect (English) /
www.nissan.ca/nissanconnect/fr (French)
(for Canada).

LIC4264

EMERGENCY CALL (SOS) BUTTON (if
so equipped)

Instruments and controls

2-101

WARNING

•

Please note that the Automatic Colli-
sion Notification service and Emer-
gency Call function cannot be used in
the following conditions:

–

Emergency functions and services
will not be available without a paid
subscription

NissanConnect®

Services.

–

The NissanConnect® Services net-
work system is disabled.

–

The vehicle moves outside the
service

area

where

the

TCU

(Telematics Control Unit) is con-
nected to the system.

–

The vehicle is outside the area
where the cellular network service
is receivable.

–

The vehicle is in a location with
poor signal reception such as
tunnels,

underground

parking

garages, behind buildings or in
mountainous areas.

–

The line is busy.

–

The TCU (Telematics Control Unit)
or other systems of your vehicle
are not working properly.

–

It may not be possible to make an
emergency call depending on the
severity of a collision and/or
emergency.

•

Park the vehicle in a safe location and
set the parking brake before operat-
ing the Emergency Call (SOS) button.

•

Only use this service in case of an
emergency. There may be a penalty
for inappropriate use of the service.

•

Radio waves could adversely affect
electric medical equipment. Indi-
viduals who use a pacemaker should
contact the device manufacturer re-
garding any possible effects before
using the system.

•

The TCU (Telematics Control Unit) an-
tenna is installed inside the upper
central part of the instrument panel.
An occupant should not get any
closer to the antenna than specified
by the pacemaker manufacturer. The
radio waves from the TCU antenna
may adversely affect the operation
of the pacemaker while using the
NissanConnect® Services.

2-102

Instruments and controls

Making an emergency call

The Emergency Call (SOS) button

is un-

der a cover and is located near the map
light.

1. Press the Emergency Call (SOS) button

to make an emergency call.

2. When the line is connected, speak to the

Response Specialist.

If you want to cancel the emergency call,
press and hold the Emergency Call (SOS)
button for a few seconds.

NOTE:

•

After the Emergency Call (SOS) button
is pressed, it may take some time until
the system initiates connection, de-
pending on the technical environment
and whether the TCU (Telematics Con-
trol Unit) is being used by the other
services.

•

An indicator light on the Emergency
call (SOS) button shows the readiness
of the emergency support system. If
the indicator light is not illuminated,
pressing the Emergency Call (SOS) but-
ton does not connect your vehicle to
the Response Specialist. The indicator
light blinks while connected to the
NissanConnect®

Services

Response

Center.

•

Even when the indicator light is illumi-
nated, connection to the NissanConnect®
Services Response Center may not be
possible. If this occurs in an emergency
situation, contact the authorities by
other means.

•

To avoid disconnecting the line, keep
the engine running during an emer-
gency call, if it is safe to do so.

LIC4702

Instruments and controls

2-103

1. Type-C USB

2. Type-A USB

There are USB/iPod® charging ports lo-
cated in 1st row, two in the front media
pocket below the climate controls and one
in the console box, in the 2nd row on the
back of the center console and in the 3rd
row by the cup holders. These ports will
charge compatible devices.

NOTE:
• Not all of the USB/iPod® charging ports

will operate with the display screen. Only
the USB connection ports located under
the climate controls will allow operation
of USB/iPod® devices through the audio
system.

• For best results, it is recommended to

use the manufacturer cables, which
are sold separately. A USB Type-A to
USB Type-C adapter (or vice versa) can
also be purchased separately; how-
ever, results may vary.

CAUTION

•

Do not force a USB device into the
connector. Inserting the USB device
tilted or up-side down into the con-
nector may damage the connector.
Make sure that the USB device is con-
nected correctly into the connector.

•

Do not use a reversible USB cable.
Using the reversible USB cable may
damage the connector.

LIC5029

1st row

LIC5031

2nd row

LIC5032

3rd row (if so equipped)

USB/iPod® CHARGING PORTS

2-104

Instruments and controls

The wireless charger is located on the front
of the center console. Lay the smartphone
on the pad of the wireless charger. Charg-
ing will start automatically. The smart-
phone will be charged continuously while
the ignition switch is in the ON position.

WARNING

•

Never put metallic materials be-
tween the wireless charger and a
smartphone.

•

Those who use a pacemaker or other
medical equipment should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

•

Never put cloth over the smartphone
during charging process.

•

Never charge a smartphone when it
is wet.

•

Never put metallic materials or small
goods such as a cigarette lighter, In-
telligent Key or memory drive.

CAUTION

•

Do not put an RFID/NFC/credit card
between the wireless charger and a
smartphone. This could cause data
corruption in the card.

•

Do not use the wireless charger with
dust accumulated or dirt on the pad.

•

Do not hit the surface of the wireless
charger.

•

Do not spill liquid (water, drinks, etc.)
on the charging pad.

•

Do not use grease, oil or alcohol for
cleaning charging pad.

WIRELESS CHARGER INDICATOR

The indicator ( 1 ) will illuminate in orange
when the charging process is started.

When the charging has completed, the in-
dicator illuminates in green.

If a malfunction occurs or the charging
process has stopped, the indicator will
blink in orange for 8 seconds then turn off.

WIRELESS CHARGER OPERATION

To use the wireless charger, it is necessary
to seat the smartphone well within the
charging pad. To maximize charging per-
formance, ensure the smartphone is fully
seated on the center of the charging pad
over the "Qi" logo

. Because the location

of the power receiver may vary depending
on the smartphone, you will need to try and
find the area that suits your smartphone.

Because some smartphone cases or ac-
cessories may adversely affect charging,
remove them before wireless charging.
Turn off the vibration function of the smart-
phone before wireless charging.

LIC4701

1. Indicator

2. Charging pad

WIRELESS CHARGER (if so equipped)

Instruments and controls

2-105

NOTE:

•

Only a Qi compatible smartphone can
be used.

•

The smartphone may be warmed dur-
ing charging process and the charging
may stop by the protection function of
the wireless charger. This is not a mal-
function. If this occurs, restart charging
after the smartphone cooled down.
The indicator will blink in orange then
turn off.

•

The wireless charging process may be
stopped by the status of the smart-
phone (battery temperature, etc.).

•

If a radio noise interference occurs dur-
ing charging process, put the smart-
phone onto the center (“Qi” logo) posi-
tion of the wireless charger.

•

The wireless charging process will stop
during process of searching the Intelli-
gent Key.

•

The wireless charging process will not
be started when a USB (Universal Serial
Bus) cable is connected to the smart-
phone. The indicator may illuminate in
orange or blink if the smartphone is
put on the wireless charger with a USB
cable connected. However, charging is
not performed.

•

Depending on the type of the smart-
phone, the indicator may remain illu-
minated in orange even when the
charging process has been completed.

This device complies with part 15 of the
FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
RF Radiation Exposure Statement: This
equipment complies with FCC RF Radia-
tion exposure limits set forth for an un-
controlled environment.
This device and its antenna must not be
co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and
operated with a minimum distance of
15cm between the radiator and your
body.

ISED Compliance Statement
This device complies with RSS-Gen of IC
Rules
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Changes or modifications made to this
device, not expressly approved by LG
Vehicle Components Company, will void
the user’s authority to operate the
equipment.
ISED RF Radiation Exposure Statement:
This equipment complies with ISED RF
Radiation exposure limits set forth for an
uncontrolled environment. This device
and its antenna must not be co-located
or operating in conjunction with any
other

antenna

transmitter.

This

equipment should be installed to oper-
ate with a minimum distance of 15 cm
between the radiator and the end-user’s
body and arms.

2-106

Instruments and controls

The Rear Door Alert system functions un-
der certain conditions to indicate there
may be an object or passenger in the rear
seat(s). Check the seat(s) before exiting the
vehicle.

The Rear Door Alert system is initially dis-
abled. The driver can enable the system
using the vehicle information display. For
additional information, see “Vehicle infor-
mation display–7 inch (18 cm) Type A”
(P. 2-24) or “Vehicle information display—12.3
inch (31 cm) Type B” (P. 2-49).

When the system is enabled:
• The system is activated when a rear door

is opened and closed within 10 minutes of
the vehicle being driven. When the driver
door is closed and the system is acti-
vated, a visual message appears in the
vehicle information display. For additional
information, see “Rear Door Alert is acti-
vated” (P. 2-66).

• If a rear door is opened and closed but

the vehicle is not driven within approxi-
mately 10 minutes, the system will not be
activated. A rear door must be opened
and closed and the car driven within 10
minutes for the system to activate.

When the Rear Door Alert system is acti-
vated:
• When the driver puts the vehicle in the P

(Park) position, a notification message
appears in the vehicle information dis-
play with the options to “Dismiss Mes-
sage” or “Disable Alert” if desired.

• Select “Disable Alert” to temporarily

disable for that stop.

• No selection or ‘Dismiss Message” will

keep the alert enabled for that stop.

• If the alert is enabled when a driver exits

the vehicle, a message will appear in the
vehicle information display that states
“Check Rear Seat For All Articles.”

If “Horn & Alert” setting is selected:

• An audible horn sound will occur after

a short time unless a rear door is
opened and closed within a short time
to deactivate the alert.

• If the doors are locked before the alert

is deactivated by opening a rear door,
the horn will sound.

• If the liftgate is opened before a rear

door is opened, the horn will be de-
layed until after the liftgate is closed.

NOTE:
If “Alert Only” setting is selected, the
message alert will still be shown in the
vehicle information display but the horn
will not sound.

WARNING

•

If the driver selects “Disable Alert”, no
audible alert will be provided regard-
less of rear door open/close status.

•

There may be times when there is an
object or passenger in the rear
seat(s) but the audible alert does not
sound. For example, this may occur if
rear seat passengers enter or exit the
vehicle during a trip.

•

The system does not directly detect
objects or passengers in the rear
seat(s). Instead, it can detect when a
rear door is opened and closed, indi-
cating that there may be something
in the rear seat(s).

NOTE:
There may be times when the horn
sounds but there are no objects or pas-
sengers in the rear seat(s).

For additional information, see “Rear Door
Alert is activated” (P. 2-66).

REAR DOOR ALERT

Instruments and controls

2-107

12V OUTLETS

The power outlets are for powering elec-
trical accessories such as cellular tele-
phones. They are rated at 12 volt, 120W (10A)
maximum.

The instrument panel power outlet is pow-
ered only when the ignition switch is in the
ON position.

CAUTION

•

The outlet and plug may be hot dur-
ing or immediately after use.

•

Only certain power outlets are de-
signed for use with a cigarette lighter
unit. Do not use any other power out-
let for an accessory lighter. It is rec-
ommended that you visit a NISSAN
dealer for additional information.

•

Do not use with accessories that ex-
ceed a 12 volt, 120W (10A) power draw.

•

Do not use double adapters or more
than one electrical accessory.

•

Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.

•

Avoid using power outlets when the
air conditioner, headlights, or rear
window defroster is on.

•

Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned off.

•

Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.

•

When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.

LIC4703

Instrument Panel

LIC4705

Cargo Area (if so equipped)

POWER OUTLETS

2-108

Instruments and controls

120V OUTLET (if so equipped)

CAUTION

•

The outlet and plug may be hot dur-
ing or immediately after use.

•

Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.

•

Do not use accessories that exceed a
120V, 150W power draw. Do not use
double adaptors or more than one
electrical accessory.

•

Avoid using power outlets when the
air conditioner, headlights or rear
window defroster is on.

•

Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned OFF.

•

Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.

•

When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.

The extended storage switch is used when
the vehicle is in transit from the factory. It is
located above the brake pedal underneath
the instrument panel. If any electrical
equipment does not operate, ensure the
extended storage switch is pushed fully in
place, as shown.

LIC4706

2nd Row

LIC4753

EXTENDED STORAGE SWITCH

Instruments and controls

2-109

LOWER CONSOLE STORAGE TRAY

SEATBACK POCKETS (if so
equipped)

There is one seatback pocket located on
the back of the driver and passenger seats.
The pockets can be used to store maps.

WARNING

To ensure proper operation of the driv-
er’s and/or front passenger’s NISSAN
Advanced

Air

Bag

System

(if

equipped), please observe the follow-
ing items:

•

Do not allow a passenger in the rear
seat or 2nd row to push or pull on the
seatback pocket or head restraint/
headrest.

•

Do not place heavy loads heavier
than 9.1 lbs. (4 kg) on the seatback,
head restraint/headrest or in the
seatback pocket.

LIC4711

LIC2618

Instruments and controls

2-111

GLOVE BOX

Open the glove box by pulling the handle.
Use the mechanical key when locking or
unlocking the glove box.

WARNING

Keep the glove box lid closed while
driving to help prevent injury in an ac-
cident or a sudden stop.

CONSOLE BOX

To open the console box, pull the lever up

and raise the lid

To close, push the lid down until the lock
latches.

LIC5344

2nd row (if so equipped)

LIC4714

LIC4752

Instruments and controls

2-113

OVERHEAD SUNGLASSES
STORAGE

To open the sunglasses holder, push and
release.

Only store one pair of sunglasses in the
holder.

WARNING

Keep the sunglasses holder closed
while driving to avoid obstructing the
driver’s view and to help prevent an
accident.

CAUTION

•

Do not use for anything other than
sunglasses.

•

Do not leave sunglasses in the sun-
glasses holder while parking in direct
sunlight. The heat may damage the
sunglasses.

CUP HOLDERS

LIC4034

LIC4718

Front console

Instruments and controls

2-115

CAUTION

Avoid abrupt starting and braking
when the cup holder is being used to
prevent spilling the drink. If the liquid is
hot, it can scald you or your passenger.

CAUTION

Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.

CAUTION

•

Do not use the bottle holder for any
other objects that could be thrown
about in the vehicle and possibly in-
jure people during sudden braking or
an accident.

•

Do not use the bottle holder for open
liquid containers.

LIC4720

3rd row

LIC4710

Bottle holder — front

LIC4723

Bottle holder — rear

Instruments and controls

2-117

CARGO AREA STORAGE BIN

To access the floor storage area pull up on
the strap to lift the luggage board.

LUGGAGE HOOKS

When securing items using luggage hooks
located on the upper side finisher do not
apply a load over more than 6.5 lbs. (29 N)
to a single hook.

The cargo hooks that are located closer
to the floor should have loads less than
110 lbs. (490 N) to a single hook.

The cargo hooks can be used to secure
cargo with ropes or other types of straps.

LIC4724

LIC4725

LIC4726

2-118

Instruments and controls

WARNING

•

Properly secure all cargo with ropes
or straps to help prevent it from slid-
ing or shifting. Do not place cargo
higher than the seatbacks. In a sud-
den stop or collision, unsecured
cargo could cause personal injury.

•

Use suitable ropes and hooks to se-
cure cargo.

•

Never allow anyone to ride in the lug-
gage area. It is extremely dangerous
to ride in a cargo area inside of a ve-
hicle. In a collision, people riding in
these areas are more likely to be se-
riously injured or killed.

•

Do not allow people to ride in any
area of your vehicle that is not
equipped with seats and seat belts.

•

The child restraint top tether strap
may be damaged by contact with
items in the cargo area. Secure any
items in the cargo area. Your child
could be seriously injured or killed in
a collision if the top tether strap is
damaged.

•

Be sure everyone in your vehicle is in
a seat and using a seat belt properly.

ROOF RACK (Type A) (if so
equipped)

WARNING

•

Always install the crossbars onto the
roof side rails before loading cargo of
any kind. Loading cargo directly onto
the roof side rails or the vehicle’s roof
may cause vehicle damage.

•

Roof rack cross bars should be evenly
distributed.

•

Do not exceed maximum roof rack
crossbars load capacity and always
distribute the load uniformly.

•

Heavy loading of the crossbars has
the potential to affect the vehicle
stability and handling during sudden
or unusual handling maneuvers.

•

Properly secure all cargo with ropes
or straps to help prevent it from
sliding or shifting. In a sudden stop
or collision, unsecured cargo could
cause personal injury.

•

Drive extra carefully when the vehicle
is loaded at or near the cargo carry-
ing capacity, especially if the signifi-
cant portion of that load is carried on
the crossbars.

CAUTION

•

Use care when placing or removing
items from the roof rack. If you can-
not comfortably lift the items onto
the roof rack from the ground, use a
ladder or a stool.

Do not apply any load directly to the roof side
rails

. Crossbars

must be installed

before applying load/cargo/luggage to the
roof of the vehicle.

LIC4202

Instruments and controls

2-119

Genuine NISSAN accessory crossbars may
be available through a NISSAN dealer. It is
recommended that you visit a NISSAN
dealer for additional information.

The service load capacity for the roof side
rails is 220 lbs. (100 kg.), however do not
exceed the crossbars load capacity.

Be careful that your vehicle does not ex-
ceed the Gross Vehicle Weight Rating
(GVWR) or its Gross Axle Weight Rating
(GAWR front and rear).

For additional information regarding GVWR
and GAWR, refer to:
• F.M.V.S.S. or C.V.M.S.S. certification label (lo-

cated on the driver’s door pillar).

Installing Crossbars (if so
equipped)

WARNING

•

It is recommended that you have the
roof rack crossbars installed by a
NISSAN dealer.

•

Make

sure

the

moonroof

(if

equipped) is in the closed position
during the installation process.

CAUTION

Protect the painted area on the vehicle
roof under the crossbars by placing a
piece of cloth under the cross bars to
prevent scratch damage.

ROOF RACK (Type B) (if so
equipped)

WARNING

•

Always install the crossbars onto the
roof side rails before loading cargo of
any kind. Loading cargo directly onto
the roof rack or the vehicle’s roof may
cause vehicle damage.

•

Do not remove load label on both
sides of the front stanchions.

LIC5334

Roof rack (for Rock Creek®)

2-120

Instruments and controls

•

Do not exceed maximum roof rack
load capacity and always distribute
the load uniformly. Heavy loading
of the roof rack has the potential to
affect the vehicle stability and han-
dling during sudden or unusual han-
dling maneuvers.

•

Properly secure all cargo with ropes
or straps to help prevent it from
sliding or shifting. In a sudden stop
or collision, unsecured cargo could
cause personal injury.

•

Drive extra carefully when the vehicle
is loaded at or near the cargo carry-
ing capacity, especially if the signifi-
cant portion of that load is carried on
the roof rack.

CAUTION

•

Use care when placing or removing
items from the roof rack. If you can-
not comfortably lift the items onto
the roof rack from the ground, use a
ladder or a stool.

•

Do not put load directly on the roof
rack. To avoid damage to paint, the
rubber seal and plastic supports, use
soft padding or soft cloth on the
crossbar before putting rough sur-
face load like plywood, lumber, etc.

Genuine NISSAN accessory roof rack at-
tachments may be available through a
NISSAN dealer. It is recommended that
you visit a NISSAN dealer for additional
information.

The service load capacity for the roof side
rails is 220 lbs. (100 kg.).

Be careful that your vehicle does not ex-
ceed the Gross Vehicle Weight Rating
(GVWR) or its Gross Axle Weight Rating
(GAWR front and rear).

For additional information regarding GVWR
and GAWR, refer to:
• F.M.V.S.S. or C.V.M.S.S. certification label (lo-

cated on the driver’s door pillar).

POWER WINDOWS

WARNING

•

Make sure that all passengers have
their hands, etc., inside the vehicle
while it is in motion and before clos-
ing the windows. Use the window
lock switch to prevent unexpected
use of the power windows.

•

To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not
leave children, people who require
the assistance of others or pets unat-
tended in your vehicle. Additionally,
the temperature inside a closed ve-
hicle on a warm day can quickly be-
come high enough to cause a signifi-
cant risk of injury or death to people
and pets.

The power windows operate when the ig-
nition switch is placed in the ON position or
for a period of time after the ignition switch
is placed in the OFF position. If the driver's
or passenger's door is opened during this
period of time, the power to the windows is
canceled.

WINDOWS

Instruments and controls

2-121

Driver's side power window switch

The driver's side control panel is equipped
with switches to open or close all of the
windows.

To open a window, push the switch to the
detent and continue to hold down until the
desired window position is reached. To
close a window, pull the switch to the de-
tent and continue to hold up until the de-
sired window position is reached.

Locking rear passengers'
windows

When the window lock button is pressed
(the indicator illuminates), the rear passen-
gers’ windows cannot be operated with the
rear passengers’ power window switch.
The rear passengers’ windows can only be
operated with the main switch (driver side
switches). To cancel the passenger’s win-
dow lock, press the window lock button
again.

Front passenger's power window
switch

The passenger's window switch operates
only the corresponding passenger's win-
dow. To open the window partially, push the
switch down

lightly until the desired

window position is reached. To close the
window partially, pull the switch up

until

the desired window position is reached.

LIC4727

1. Window lock button

2. Left rear passenger side switch

3. Driver’s side switch

4. Power door lock/unlock switch

5. Front passenger side switch

6. Right rear passenger side switch

LIC4728

2-122

Instruments and controls

Rear power window switch

The rear power window switches open or
close only the corresponding windows. To
open the window, push the switch and hold
it down

. To close the window, pull the

switch up

Automatic operation

To fully open a window equipped with au-
tomatic

operation,

push

the

window

switch down to the second detent and re-
lease it; it need not be held. The window
automatically opens all the way. To stop
the window, lift the switch up while the win-
dow is opening.

Auto-reverse function

The auto-reverse function can be acti-
vated when a window is closed by auto-
matic operation.

Depending on the environment or driv-
ing conditions, the auto-reverse func-
tion may be activated if an impact or
load similar to something being caught
in the window occurs.

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the window.

If the vehicle's battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate
properly. If this occurs, please contact the
dealer to re-initialize the power window
auto-reverse system.

If the control unit detects something
caught in a window equipped with auto-
matic operation, as it is closing, the window
will be immediately lowered.

LIC4729

LIC4730

Instruments and controls

2-123

When power window switch does
not operate

If the power window automatic function
(closing only) does not operate properly,
perform the following procedure to initial-
ize the power window system:

1. Place the ignition switch in the ON

position.

2. Open the window more than halfway by

operating the power window switch.

3. Pull the power window switch and hold it

to close the window, and then hold the
switch more than 3 seconds after the
window is closed.

4. Release the power window switch. Oper-

ate the window by the automatic function
to confirm the initialization is complete.
The power window automatically opens
or closes depending on if the automatic
down or up function is selected.

5. Perform steps 2 through 4 above for

other windows.

If the power window function does not op-
erate properly after performing the above
procedure have the system checked and
repaired. It is recommended that you visit a
NISSAN dealer for this service.

REAR DOOR SUNSHADE (if so
equipped)

The rear door sunshade is located within
the rear doors at the base of the window.
• To raise the sunshade, pull up the center

tab

• Hook the sunshade slots onto the tabs

extending from the top of the window
frame

CAUTION

•

Do not release the rear door sunshade
during operation. This could damage
the sunshade or cause injury.

•

Do not forcefully pull the sunshade.
Doing so may elongate the sunshade.
This could cause improper operation
or could damage the sunshade.

•

Do not place objects on or near the
rear sunshade. This could cause im-
proper operation or could damage
the sunshade.

NOTE:
To avoid damage to the sunshade,
please note the following:
• Do not pull or push the sunshade, other

than upwards.

• Do not pull or push the sunshade with

the sunshade hung on the hooks.

• Do not allow liquids or objects on the

storing area of the sunshade.

LIC4169

2-124

Instruments and controls

WARNING

•

In an accident you could be thrown
from the vehicle through an open
moonroof. Always use seat belts and
child restraints.

•

Do not allow anyone to stand up or
extend any portion of their body of
the moonroof opening while the ve-
hicle is in motion or while the moon-
roof is closing.

CAUTION

•

Remove water drops, snow, ice or
sand from the moonroof before
opening.

•

Do not place any heavy object on the
moonroof or surrounding area.

AUTOMATIC MOONROOF AND
SUNSHADE

Sliding sunshade and moonroof

When the sunshade switch is pushed to
the OPEN position

, the sunshade open.

(If the sunshade starts to open from the
position between close and half open, the
sunshade will stop half. When the switch is
pushed again, the sunshade will open fully.)
When the moonroof switch is pushed to
the OPEN position

, the moonroof opens

to the comfort mode position. (If the sun-
shade is close, the sunshade will open half
first. When the switch is pushed again, the
moonroof will open fully.)

When the moonroof switch is pushed to
the CLOSE position

, the moonroof will

automatically close. When the sunshade
switch is pushed to the CLOSE position

the sunshade will close. (If the sunshade
starts to close from the position between
full and half open, the sunshade will stop
half. When the switch is pushed again, the
sunshade will close fully. However, if the
moonroof is open or tilted up, the sun-
shade will not close beyond half.)

To stop the sunshade or moonroof during
the operation, push the moonroof switch
to either of the OPEN

, CLOSE

or UP

position.

Tilting the moonroof

To tilt up the moonroof, push the moonroof
switch to the UP position

. To tilt down

the moonroof, push the switch to the
CLOSE position

Comfort mode

This is the position used when driving with
the moonroof open. When driving with the
moonroof fully open, wind noise may be
very loud. Use the comfort mode position
when driving.

LIC4759

POWER MOONROOF (if so equipped)

Instruments and controls

2-125

Auto-reverse function

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the moonroof and sunshade.

The auto-reverse function enables the
moonroof and sunshade to automatically
reverse when something is caught in the
moonroof and sunshade as it is closing.
When the control unit detects an obstacle,
the moonroof and sunshade will open
immediately.

Depending on the environment or driving
conditions, the auto-reverse function may
activate if an impact or load similar to
something being caught in the moonroof
and sunshade occurs.

If the auto-reverse function activates con-
secutively or the battery is discharged, the
moonroof and sunshade may not close
properly. In this case, push and hold the
switch to the CLOSE position

to close

the moonroof.

If the moonroof switch does not
operate

If the moonroof and sunshade do not op-
erate properly, perform the following pro-
cedure to initialize the operation system.

1. If the moonroof and sunshade are open,

close them fully by repeatedly pushing
the moonroof switch to the CLOSE

and

position.

2. Push and hold the moonroof switch to

the CLOSE

position for 10 seconds.

3. After the moonroof and sunshade

move slightly to the closed position and
then move back a little, release the
moonroof switch.

4. Push and hold the moonroof switch to

the CLOSE

position, and the glass

and shade will move.

5. Release the moonroof switch. Then the

moonroof and sunshade will fully open
and then fully close.

6. Check if the moonroof switch operates

normally.

WARNING

The driver is always responsible for op-
erating the moonroof properly, includ-
ing the operation by all passengers.
Failure to follow the warnings and in-
structions for proper use of the moon-
roof could result in serious injury or
death.

•

Do not allow children to operate the
moonroof. Improper operation by
children may cause an accident. If
children or others get caught in the
moonroof, it could cause serious
injury.

•

To help avoid risk of injury or death
through unintended operation of the
moonroof, place the ignition switch
in the OFF position when leaving the
vehicle, and do not leave children and
the Intelligent Key inside the vehicle.

•

Do not activate the auto-reverse
function intentionally. If hands or
face, etc. get caught in the moonroof,
it could cause serious injury.

2-126

Instruments and controls

CAUTION

•

Do not place objects (such as news-
papers, handkerchiefs, etc.) on the
sunshade when it is extending or re-
tracting causing improper operation
or damage to the sunshade.

•

Do not push the sunshade arm with
your hands, etc., as this may deform
it. Improper operation or damage to
the sunshade may result.

•

Do not put any object into the sun-
shade inlet port as this may result in
improper operation or damage the
sunshade.

•

Do not hang any object on the arm
rail as this may result in improper op-
eration or damage the sunshade.

•

Do not forcefully pull the sunshade.
Doing so may elongate the sun-
shade. Improper operation or dam-
age to the sunshade may result.

If the moonroof does not operate properly
after performing the procedure above,
have your vehicle checked by a NISSAN
dealer.

䊊

The interior light can be turned on re-
gardless of door position. The light will
go off after a period of time unless the
ignition switch is placed in the ON posi-
tion when any door is opened.

䊊

The interior lights can be set to operate
when the doors are opened. To turn off
the interior lights when a door is open,
push the switch, the interior lights will not
illuminate, regardless of door position.
The lights will go off when the ignition
switch is placed in the ON position, or the
driver's door is closed and locked. The
lights will also go off after a period of time
when the doors are open.

NOTE:

The footwell lights illuminate when the
driver and passenger doors are opened
regardless of the interior light switch po-
sition. These lights will turn off auto-
matically after a period of time while
doors are open to prevent the battery
from becoming discharged.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

LIC4033

INTERIOR LIGHTS

Instruments and controls

2-127

MAP LIGHTS

To turn the map lights on, push the
switches. To turn them off, push the
switches again.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

PERSONAL LIGHTS

To turn on the personal lights, push and
release the switch

To turn off the personal lights, push and
release the switch

CARGO LIGHT

The cargo light on the overhead trim has a
three-position switch. To operate, push the
switch to the desired position.

䊊

ON: The light is illuminated.

䊊

DOOR: The light illuminates when the
liftgate is opened. The light turns off
when the liftgate is closed.

䊊

OFF: The light does not illuminate re-
gardless of liftgate position or lock
status.

LIC4035

LIC1413

SIC2063A

2-128

Instruments and controls

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

The HomeLink® Universal Transceiver pro-
vides a convenient way to consolidate the
functions of up to three individual hand-
held transmitters into one built-in device.

HomeLink® Universal Transceiver:
• Will operate most Radio Frequency (RF)

devices such as garage doors, gates,
home and office lighting, entry door locks
and security systems.

• Is powered by your vehicle's battery. No

separate batteries are required. If the ve-
hicle's battery is discharged or is discon-
nected,

HomeLink®

will

retain

all

programming.

When the HomeLink® Universal Trans-
ceiver is programmed, retain the original
transmitter for future programming pro-
cedures (Example: new vehicle pur-
chases). Upon sale of the vehicle, the
programmed

HomeLink®

Universal

Transceiver buttons should be erased for
security purposes. For additional infor-
mation, see “Programming HomeLink®”
(P. 2-130).

WARNING

•

Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards
became effective for opener models
manufactured after April 1, 1982.) A
garage door opener which cannot
detect an object in the path of a clos-
ing garage door and then automati-
cally stop and reverse does not meet
current federal safety standards. Us-
ing a garage door opener without
these features increases the risk of
serious injury or death.

•

During the programming procedure
your garage door or security gate
will open and close (if the transmitter
is within range). Make sure that
people or objects are clear of the
garage door, gate, etc., that you are
programming.

HOMELINK® UNIVERSAL
TRANSCEIVER (if so equipped)

Instruments and controls

2-129

•

Your vehicle's engine should be
turned off while programming the
HomeLink® Universal Transceiver. Do
not breathe exhaust gases; they con-
tain colorless and odorless carbon
monoxide. Carbon monoxide is dan-
gerous. It can cause unconscious-
ness or death.

PROGRAMMING HOMELINK®

The following steps show generic instruc-
tions on how to program a HomeLink® but-
ton. If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com/nissan

call

1-800-355-3515.

NOTE:

It is also recommended that a new bat-
tery be placed in the hand-held trans-
mitter of the device being programmed
to HomeLink® for quicker programming
and accurate transmission of the radio-
frequency.

䊊

HomeLink® buttons (1–3)

䊊

Indicator light (appears above each
HomeLink® button)

1. Position the end of your hand-held

transmitter 1-3 inches (2-8 cm) away
from the HomeLink® button that you
would wish to program while keeping
the indicator light in view.

2. Simultaneously press and hold both the

chosen HomeLink® and hand-held trans-
mitter buttons until the HomeLink® indi-
cator light changes from a slow to a rap-
idly blinking light. Now you may release
both the HomeLink® and hand-held
transmitter buttons.

LIC5068

LIC5069

2-130

Instruments and controls

NOTE:

Some hand-held transmitters (garage
door opener remote) may actually train
better at a distance of 6–12 inches (15–20
cm). Keep this in mind if you have diffi-
culty with the programming process.

3. Firmly

press, hold for five seconds and

release

the programmed HomeLink®

button up to two separate times to ac-
tivate the door. If the door does not acti-
vate, press and hold the just trained
HomeLink® button and observe the indi-
cator light.

• If the indicator light

stays on con-

stantly, programming is complete

and your device should activate when
the Homelink® button is pressed and
released.

• If the indicator light blinks

rapidly for

two seconds and then turns to a
constant light, continue with “Pro-
gramming” steps 4–6

to complete

the programming of a rolling code
equipped device (most commonly a
garage door opener).

NOTE:

Some devices may require you to replace
this Programming Step 2 with procedures
noted in the “Programming HomeLink® for
Canadian customers and gate openers”
(P. 2-132) section. If the HomeLink® indi-
cator light does not change to a rapidly
blinking light after performing these steps,
contact HomeLink® at www.homelink.com.

4. At the garage door opener motor (secu-

rity gate motor, etc.), locate the “Learn” or
“Set” button. This can usually be found
where the hanging antenna wire is at-
tached to the motor-head unit (see the
device’s manual to identify this button.).
The name and color of the button may
vary by manufacturer.

NOTE:

A ladder and/or second person may sim-
plify the following steps. Do not stand on
your vehicle to perform the next steps.

5. Firmly press and release the “Learn” or

“Set” button until the indicator illumi-
nates. Once the button is pressed, you
have approximately 30 seconds to initi-
ate the next step.

6. Return to the vehicle and firmly press,

hold for two seconds and release the
HomeLink® button up to three times.

not press the HomeLink® button rap-
idly.

At this point programming is com-

plete and your device should operate
when the HomeLink® button is pressed
and released.

LIC4798

Example

Instruments and controls

2-131

Nissan Pathfinder (2024 year). Manual in english - page 7