Nissan Leaf (2024 year). Manual in english

When performing any inspection or main-
tenance work on your vehicle, always take
care to prevent serious accidental injury to
yourself or damage to the vehicle. The fol-
lowing are general precautions that should
be closely observed.

WARNING

•

The EV system uses high voltage up
to approximately DC 400 volt. The
system can be hot during and after
starting and when the vehicle is shut
off. Be careful of both the high volt-
age and the high temperature. Obey
the labels that are attached to the
vehicle.

•

Never disassemble, remove or re-
place high-voltage parts and cables
as well as their connectors. High-
voltage cables are colored orange.

•

Disassembling, removing or replac-
ing those parts or cables can cause
severe burns or electric shock that
may result in serious injury or death.
The vehicle high-voltage system has
no user serviceable parts. It is recom-
mended that you visit a NISSAN cer-
tified LEAF dealer for any necessary
maintenance.

•

Park the vehicle on a level surface,
apply the parking brake securely and
chock the wheels to prevent the ve-
hicle from moving. Push the P (Park)
position switch on the shift lever or
place the vehicle into the N (Neutral)
position.

•

If you must work with the EV (Electric
Vehicle) system is turned on, keep
hands, clothing, hair and tools away
from moving fans and any other
moving parts.

•

Make sure that the power switch is
in the OFF or LOCK position when
performing any part replacement or
repairs.

•

It is advisable to secure or remove
any loose clothing and remove any
jewelry, such as rings, watches, etc.
before working on your vehicle.

•

Always wear eye protection when-
ever you work on your vehicle.

•

Never get under the vehicle while it is
supported only by a jack. If it is nec-
essary to work under the vehicle,
support it with safety stands.

•

Keep smoking materials, flames and
sparks away from the 12-volt battery.

CAUTION

•

Do not work under the hood while
the motor compartment is hot. Push
the power switch in the OFF position
and wait until it cools down.

•

Avoid direct contact with used coolant.
Improperly disposed coolant and/or
other vehicle fluids can damage the
environment. Always conform to local
regulations for the disposal of vehicle
fluids.

•

Never connect or disconnect the bat-
tery or any transistorized compo-
nent while the power switch is in the
ON position.

•

Your vehicle is equipped with an auto-
matic cooling fan. It may come on at
any time without warning, even if the
power switch is not in the ACC, ON or
READY to drive position. To avoid in-
jury, always disconnect the negative
12-volt battery cable before working
near the fan.

MAINTENANCE PRECAUTIONS

8-2

Do-it yourself

•

Before

performing

any

electrical

maintenance work on the vehicle such
as the battery, fuses or bulb replace-
ment, confirm the following:

–

The charge connector is removed

from the vehicle.

–

The Climate Ctrl. Timer is not active

or operating. For additional infor-
mation, see “Climate Ctrl. Timer”
(P. 4-38).

–

The 12-volt battery is not being

charged by the Li-ion battery and
that all charging status indicator
lights are off. For additional infor-
mation, see “Charging the 12-volt
battery” (P. EV-5) and “Charging
status indicator lights” (P. CH-50).

•

The power switch is in the OFF posi-
tion. Place the power switch in the ON
position and then in the OFF position
to prevent the 12-volt battery auto-
matically being charged by the Li-ion
battery. For additional information,
see “Charging the 12-volt battery”
(P. EV-5).

NOTE:

If the battery is completely drained the
transmission will not manually shift to
other positions.

The “Do-it-yourself ” section gives instruc-
tions regarding only those items that are
relatively easy for an owner to perform.

A Genuine NISSAN Service Manual is also
available. For additional information, see
“Owner’s manual/service manual order
information” (P. 10-22).

You should be aware that incomplete or
improper servicing may result in operating
difficulties and could affect your warranty
coverage.

If in doubt about any servicing,

it is recommended that you visit a NISSAN
certified LEAF dealer.

Do-it yourself

8-3

The cooling system is filled at the factory
with a pre-diluted mixture of 50% Genuine
NISSAN Long Life Antifreeze/Coolant (blue)
and 50% water to provide year-round anti-
freeze and coolant protection. The anti-
freeze solution contains rust and corrosion
inhibitors. Additional cooling system addi-
tives are not necessary.

WARNING

•

Never remove the coolant reservoir
cap when the motor compartment is
hot. Wait until the motor compart-
ment cools down.

•

The coolant reservoir is equipped with
a pressure type coolant reservoir cap.
To prevent damage to the motor com-
partment, use only a Genuine NISSAN
coolant reservoir cap.

CAUTION

•

Never use any additives in the coolant
such as radiator sealer in the cooling
system. This may cause damage to
electrical equipment such as the mo-
tor and inverter.

•

When adding or replacing coolant, be
sure to use only a Genuine NISSAN
Long Life Antifreeze/Coolant (blue)
or equivalent. Genuine NISSAN Long
Life Antifreeze/Coolant (blue) is pre-
diluted to provide antifreeze protec-
tion to −34°F (−37°C) . If additional
freeze protection is needed due to the
weather conditions where you oper-
ate your vehicle, add Genuine NISSAN
Long Life Antifreeze/Coolant (blue)
concentrate following the directions
on the container. If an equivalent cool-
ant other than Genuine NISSAN Long
Life Antifreeze/Coolant (blue) is used,
follow the coolant manufacturer's in-
structions to maintain minimum anti-
freeze protection to −34°F (−37°C). The
use of other types of coolant solutions
other than Genuine NISSAN Long Life
Antifreeze/Coolant (blue) or equiva-
lent may damage the cooling system.

•

The life expectancy of the factory-fill
coolant is 125,000 miles (200,000 km)
or 15 years. Mixing any other type of
coolant other than Genuine NISSAN
Long Life Antifreeze/Coolant (blue)(or
equivalent coolant), including Genuine
NISSAN Long Life Antifreeze/Coolant
(green), or the use of non-distilled
water may reduce the life expectancy
of the factory-filled coolant. For addi-
tional information, refer to the “Main-
tenance and schedules” section of this
manual.

COOLING SYSTEM

Do-it yourself

8-5

CHECKING COOLANT LEVEL

Check the coolant level

in the reservoir

when the high-voltage parts are cold.

the coolant level is below the MIN level

open the reservoir cap and add coolant up
to the MAX level

. If the reservoir is empty,

check the coolant level in the coolant res-
ervoir

when the high-voltage parts are

cold.

If there is insufficient coolant in the

coolant reservoir, fill the coolant reservoir
with coolant up to the reservoir cap open-
ing and also add it to the reservoir up to the
MAX level

Tighten the cap securely after adding coolant.

For additional information on the location
of the coolant reservoir, see “Motor com-
partment check locations” (P. 8-4).

If the cooling system frequently requires
coolant, it is recommended that you visit
a NISSAN certified LEAF dealer.

CHANGING COOLANT

It is recommended that major cooling sys-
tem repairs should be performed by a
NISSAN certified LEAF dealer. The service
procedures can be found in the appropri-
ate NISSAN Service Manual.

Improper servicing can result in reduced
heater performance.

WARNING

•

To avoid the danger of being scalded,
never change the coolant when the
motor compartment is hot.

•

Never remove the coolant reservoir
cap when the motor compartment is
hot. Serious burns could be caused
by high-pressure fluid escaping from
the radiator.

•

Avoid direct skin contact with used
coolant. If skin contact is made, wash
thoroughly with soap or hand cleaner
as soon as possible.

•

Keep coolant out of reach of children
and pets.

Coolant must be disposed of properly.
Check your local regulations.

LDI3145

8-6

Do-it yourself

When checking or replacement is required,
it is recommended that you visit a NISSAN
certified LEAF dealer for this service.

CAUTION

•

Use only Genuine NISSAN Matic S ATF.
Do not mix with other fluids.

•

Using reduction gear fluid other than
Genuine NISSAN Matic S ATF will cause
deterioration in driveability and re-
duction gear durability, and may dam-
age the reduction gear, which is not
covered by the NISSAN New Vehicle
Limited Warranty.

For additional brake fluid information, see
“Recommended fluids/lubricants and ca-
pacities” (P. 10-2).

WARNING

•

Use only new fluid from a sealed con-
tainer. Old, inferior or contaminated
fluid may damage the brake system.
The use of improper fluids can dam-
age the brake system, and affect the
vehicle’s stopping ability.

•

Clean the filler cap before removing.

•

Brake fluid is poisonous and should
be stored carefully in marked con-
tainers out of the reach of children.

CAUTION

Do not spill the fluid on any painted sur-
faces. This will damage the paint. If fluid
is spilled, immediately wash the sur-
face with water.

Check the fluid level in the reservoir. If the
fluid is below the MIN line

or the brake

warning light illuminates, add Genuine
NISSAN Super Heavy Duty Brake Fluid or
equivalent

DOT 3

fluid up to the MAX line

If fluid must be added frequently, the
system should be checked. It is recom-
mended that you visit a NISSAN certified
LEAF dealer for this service.

LDI3143

REDUCTION GEAR FLUID

BRAKE FLUID

Do-it yourself

8-7

Fill the windshield-washer fluid reservoir
periodically. Add windshield-washer fluid
when the “Low Washer Fluid” message ap-
pears on the vehicle information display.
For additional information, see “Vehicle in-
formation display warnings and indicators”
(P. 2-34).

To fill the windshield-washer fluid reservoir,
lift the cap

and pour the windshield-

washer fluid into the reservoir opening.

Add a windshield-washer solvent to the res-
ervoir for better cleaning. In the winter sea-
son, add a windshield-washer antifreeze.
Follow the manufacturer’s instructions for
the mixture ratio.

Refill the reservoir more frequently when
driving conditions require an increased
amount of windshield-washer fluid.

Recommended fluid:

Genuine NISSAN Windshield-Washer Con-
centrate Cleaner & Antifreeze or equivalent

CAUTION

•

Do not substitute antifreeze coolant
for windshield-washer solution. This
may result in damage to the paint.

•

Do not fill the windshield-washer res-
ervoir with windshield-washer fluid
concentrates at full strength. Some
methyl

alcohol

based

windshield-

washer fluid concentrates may per-
manently stain the grille if spilled
while filling the windshield-washer
reservoir.

•

Pre-mix

windshield-washer

fluid

concentrates

with

water

the

manufacturer’s recommended levels
before pouring the fluid into the
windshield-washer reservoir. Do not
use the windshield-washer reservoir
to mix the windshield-washer fluid
concentrate and water.

LDI3463

WINDSHIELD-WASHER FLUID

8-8

Do-it yourself

Caution symbols for battery

WARNING

No smoking, No exposed flames,

No Sparks

Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by the battery is

explosive. Explosive gases can cause blindness or injury.

Shield eyes

Handle the battery cautiously. Always wear eye protection glasses to protect against explosion or

battery acid.

Keep away from children

Never allow children to handle the battery. Keep the battery out of the reach of children.

Battery acid

Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a

battery or battery cap, immediately wash your hands thoroughly. If the battery fluid gets into your

eyes, or onto your skin or clothing, flush with water immediately for at least 15 minutes and seek

medical attention. Battery fluid is acid. If the battery fluid gets into your eyes or onto your skin, it

could cause loss of your eyesight or burns.

Note operating instructions

Before handling the battery, read this instruction carefully to ensure correct and safe handling.

Explosive gas

Hydrogen gas generated by battery fluid is explosive. Explosive gases can cause blindness or

injury.

12-VOLT BATTERY

Do-it yourself

8-9

• Keep the 12-volt battery surface clean

and dry. Clean the 12-volt battery with a
solution of baking soda and water.

• Make certain the terminal connections

are clean and securely tightened.

NOTE:

Care should be taken to avoid situations
that can lead to potential battery dis-
charge and potential no-start conditions
such as:
1. Installation or extended use of elec-

tronic accessories that consume bat-
tery power when the EV system is not
running (Phone chargers, GPS, DVD
players, etc.)

2. Vehicle is not driven regularly and/or

only driven short distances.

In these cases, the battery may need to
be charged to maintain battery health

WARNING

•

Do not expose the 12-volt battery to
flames or electrical sparks. Hydrogen
gas generated by the 12-volt battery
is explosive. Do not allow 12-volt bat-
tery fluid to contact your skin, eyes,

fabrics or painted surfaces. After
touching a 12-volt battery or 12-volt
battery cap, do not touch or rub your
eyes. Thoroughly wash your hands. If
the acid contacts your eyes, skin or
clothing, immediately flush with wa-
ter for at least 15 minutes and seek
medical attention.

•

Do not operate the vehicle if the fluid
in the 12-volt battery is low. Low
12-volt battery fluid can cause a
higher load on the 12-volt battery
which can generate heat, reduce bat-
tery life, and in some cases lead to an
explosion.

•

When working on or near a 12-volt
battery, always wear suitable eye
protection and remove all jewelry.

•

12-volt battery posts, terminals and
related accessories contain lead and
lead compounds. Wash hands after
handling.

•

Keep the 12-volt battery out of the
reach of children.

1. Remove the vent caps with a screw-

driver as shown. Use a cloth to protect
the battery case.

WDI0224

8-10

Do-it yourself

2. Check the fluid level in each cell. If it is

necessary to add fluid, add only distilled
water to bring the level up to the bottom
of the filler opening.

Do not overfill.

Re-

install the vent caps.

Vehicles operated in high temperatures or
under severe conditions require frequent
checks of the 12-volt battery fluid level.

JUMP STARTING

Jump starting provides power to the 12-
volt system to allow the electrical systems
to operate. The electrical systems must
be operating to allow the Li-ion battery
to be charged. Jump starting does not
charge the Li-ion battery. The Li-ion battery
must be charged before the vehicle can be
driven.

For additional information, see “Jump
starting” (P. 6-10). If the power switch does
not switch to the READY to drive position by
jump starting, the 12-volt battery may have
to be replaced. It is recommended that you
visit a NISSAN certified LEAF dealer for this
service.

CLEANING

If your windshield is not clear after using
the windshield washer or if a wiper blade
chatters when running, wax or other mate-
rial may be on the blade or windshield.

Clean the outside of the windshield with a
washer solution or a mild detergent. Your
windshield is clean if beads do not form
when rinsing with clear water.

Clean each blade by wiping it with a cloth
soaked in a washer solution or a mild de-
tergent. Then rinse the blade with clear
water. If your windshield is still not clear
after cleaning the blades and using the
wiper, replace the blades.

CAUTION

Worn windshield wiper blades can dam-
age the windshield and impair driver
vision.

LDI3181

WINDSHIELD WIPER BLADES

Do-it yourself

8-11

REPLACING

Replace the wiper blades if they are worn.

Pulling up the wiper arm

The wiper arm should be in the up position
when replacing the wiper.

Pull up the wiper arm manually or using the
wiper rise-up function (if so equipped).

Wiper rise-up function (if so equipped)

To pull up the wiper arm, push the lever

up and hold for more than 2 seconds within
1 minute after the power switch is turned
off. The wiper operation stops in mid-
operation and wiper arm can be pulled up.

To lower the wiper arm, place the wiper
arm in the down position and then push
the lever

up once after the power switch

is turned on.

CAUTION

Do not operate the windshield wiper
while arm is pulled up. The wiper arm or
hood may be damaged.

LDI3602

8-12

Do-it yourself

Replacing

1. Push the release tab

, and move the

wiper blade down the wiper arm

while pushing the release tab to remove.

2. Insert the new wiper blade onto the wiper

arm until a click sounds.

3. Rotate the wiper blade so that the dimple

is in the groove.

CAUTION

•

After wiper blade replacement, re-
turn the wiper arm to its original po-
sition; otherwise it may be damaged
when the hood is opened.

•

Make sure the wiper blades contact
the glass; otherwise the arm may be
damaged from wind pressure.

Be careful not to clog the washer nozzle

This may cause improper windshield washer
operation. If the nozzle is clogged, remove
any objects with a needle or small pin

. Be

careful not to damage the nozzle.

LDI2602

LDI3535

Do-it yourself

8-13

REAR WINDOW WIPER BLADE

It is recommended that you visit a NISSAN
certified LEAF dealer if checking or replace-
ment is required.

If the brakes do not operate properly, have
the brakes checked. It is recommended
that you visit a NISSAN certified LEAF dealer
for this service.

WARNING

Do not adjust the height of the brake
pedal. Doing so could alter the effec-
tiveness of the brakes, which could re-
sult in a serious accident and personal
injury. If adjustment is required, it is
recommended that you visit a NISSAN
certified LEAF dealer for this service.

BRAKE PAD WEAR WARNING

The disc brake pads have audible wear
warnings. When a brake pad requires re-
placement, it will make a high–pitched
scraping sound when the vehicle is in
motion. This scraping sound will first occur
only when the brake pedal is depressed.
After more wear of the brake pad, the
sound will always be heard even if the
brake pedal is not depressed. Have the
brakes checked as soon as possible if the
wear warning sound is heard.

Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is
normal and does not affect the function or
performance of the brake system.

Proper brake inspection intervals should
be followed.

For additional information,

refer to the “Maintenance and schedules”
section of this manual.

BRAKES

8-14

Do-it yourself

MOTOR COMPARTMENT

WARNING

•

Never touch, disassemble, remove
or replace the high-voltage parts and
cables, as well as their connectors.
High-voltage cables are colored or-
ange. Touching, disassembling, re-
moving or replacing those parts and
cables can cause severe burns or
electric shock that may result in seri-
ous injury or death.

•

Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could dam-
age the electrical system or electronic
control units or cause a fire.

If any electrical equipment does not oper-
ate, check for an open fuse.

1. Confirm that the power switch and the

headlight switch are turned off.

2. Open the hood.

3. Remove the fuse/fusible link holder

cover by pushing the tab and lifting the
cover from the right side, and then the
left side.

4. Locate the fuse that needs to be replaced.

5. Remove the fuse using the fuse puller

located in the passenger compartment
fuse box.

LCE2490

FUSES

Do-it yourself

8-15

Fusible links

If any electrical equipment does not oper-
ate and the fuses are in good condition,
check the fusible links in the holders

and

. If any of these fusible links are

melted, replace only with Genuine NISSAN
parts.

For checking and replacing the fusible links
in the holders

and

, it is recom-

mended that you visit a NISSAN certified
LEAF dealer for this service.

LCE2491

Do-it yourself

8-17

PASSENGER COMPARTMENT

WARNING

Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.

If any electrical equipment does not oper-
ate, check for an open fuse.
1. Make sure that the power switch and the

headlight switch are turned off.

2. Insert a screwdriver wrapped with the

cloth

into the slit

Use a cloth

to protect the fuse box

cover.

3. Then pull to remove the fuse box cover

4. Remove the fuse with the fuse puller

5. If the fuse is open

, replace it with a

new fuse

6. If a new fuse also opens, have the elec-

trical system checked, and if necessary
repaired. It is recommended that you
visit a NISSAN certified LEAF dealer for
this service.

LVM0007X

LDI3328

8-18

Do-it yourself

Extended storage switch

If any electrical equipment does not oper-
ate, remove the extended storage switch
and check for an open fuse.

NOTE:

The extended storage switch is used for
long term vehicle storage. Even if the ex-
tended storage switch is broken it is not
necessary to replace it. Replace only the
open fuse in the switch with a new one.

How to replace the extended storage switch:

1. To remove the extended storage switch,

be sure the power switch is in the OFF
position.

2. Be sure the headlight switch is in the

OFF position.

3. Remove the fuse box cover.

4. Pinch the locking tabs

and

found

on each side of the storage switch.

5. Pull the storage switch straight out from

the fuse box

CAUTION

•

Be careful not to allow children to swal-
low the battery and removed parts.

•

An improperly disposed battery can
harm the environment. Always con-
firm local regulations for battery
disposal.

•

When changing batteries, do not let
dust or oil get on the components.

•

There is danger of explosion if the
lithium battery is incorrectly replaced.
Replace only with the same or equiva-
lent type.

LDI3205

NISSAN INTELLIGENT KEY® BATTERY
REPLACEMENT

Do-it yourself

8-19

Replace the battery in the Intelligent Key as
follows:

1. Remove the mechanical key from the

Intelligent Key.

2. Insert a small screwdriver into the slit of

the corner and twist it to separate the
upper part from the lower part. Use a
cloth to protect the casing.

3. Replace the battery with a new one.

Recommended battery:

CR2025 or equivalent

• Do not touch the internal circuit and

electric terminals as doing so could
cause a malfunction.

• Hold the battery by the edges. Holding

the battery across the contact points
will seriously deplete the storage
capacity.

• Make sure that the

丣

side faces the

bottom of the case.

4. Align the tips of the upper and lower

parts

, and then push them together

until it is securely closed.

5. Operate the buttons to check that it is

functioning properly.

It is recommended that you visit a NISSAN
certified LEAF dealer for this service.

SDI2451

SDI2452

8-20

Do-it yourself

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

For Canada:

This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause
undesired operation of the device.

1. Headlight assembly

2. Map light

3. Room light

4. High-mounted stop light

5. Rear combination light

LDI3149

LIGHTS

Do-it yourself

8-21

6. Door mirror turn signal light

(if so equipped)

7. Cargo light

8. License plate light

9. Fog light (if so equipped)

Fog may temporarily form inside the lens
of the exterior lights in the rain or in a car
wash. A temperature difference between
the inside and the outside of the lens
causes the fog. This is not a malfunction. If
large drops of water collect inside the lens,
it is recommended that you visit a NISSAN
certified LEAF dealer for this service.

HEADLIGHTS

If headlight bulb replacement is required, it
is recommended that you visit a NISSAN
certified LEAF dealer for this service.

Replacing the LED headlight bulb
(if so equipped)

If LED headlight bulb replacement is neces-
sary, it is recommended that you visit a
NISSAN certified LEAF dealer for this service.

Replacing the halogen headlight
bulb (if so equipped)

The headlight is a semi-sealed beam type
that uses a headlight (halogen) bulb. If
bulb replacement is required, it is recom-
mended that you visit a NISSAN certified
LEAF dealer.

CAUTION

•

Do not leave the bulb out of the head-
light reflector for a long period of
time. Dust, moisture, smoke, etc. en-
tering the headlight body may affect
bulb performance

•

High-pressure halogen gas is sealed
inside the halogen bulb. The bulb
may break if the glass envelope is
scratched or the bulb is dropped.

•

Only touch the base when handling
the bulb. Never touch the glass enve-
lope. Touching the glass envelope
could significantly affect bulb life
and/or headlight performance.

•

Aiming is not necessary after replac-
ing the bulb. When aiming adjustment
is necessary, it is recommended that
you visit a NISSAN certified LEAF dealer
for this service.

•

Fog may temporarily form inside the
lens of the exterior lights in the rain
or in a car wash. A temperature dif-
ference between the inside and the
outside of the lens causes the fog.
If large drops of water collect inside
the lens, it is recommended that you
visit a NISSAN certified LEAF dealer.

Use the same number and wattage as
originally installed as shown in the chart.

FOG LIGHTS (if so equipped)

For additional information on fog light bulb
replacement, refer to the instruction out-
lined in this section

Replacing the fog light bulb

If fog light bulb replacement is required, it is
recommended that you visit a NISSAN cer-
tified LEAF dealer for this service.

8-22

Do-it yourself

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No

Headlight assembly (Type A) (if so equipped)*

High*

HB3

Low*

H11

Park/Turn signal*

28/8

7444NA

Side marker*

—

Headlight assembly (Type B) (if so equipped)*

High*

—

Low*

—

Daytime running (if so equipped)*

—

Park/Turn signal*

28/8

7444NA

Side marker*

—

Front fog light (if so equipped)*

Charge port lid light*

—

Rear combination light

Turn signal

WY21W

Stop/Tail*

—

Backup

W16W

Side marker*

—

License plate light*

W5W

Map light*

—

Courtesy light*

—

Door mirror turn signal light (if so equipped)*

—

High-mounted stop light*

—

Vanity mirror light*

1.8

—

Room light*

—

Cargo light

W5W

* It is recommended that you visit a NISSAN certified LEAF dealer for replacement.

NOTE:

Always check with the Parts Department
at a NISSAN certified LEAF dealer for the
latest information about parts.

Do-it yourself

8-23

1. Remove the rear combination attach-

ment bolts

2. Pull the rear combination assembly as

shown in the illustration

3. Turn the bulb sockets and then remove

the bulbs

If you have a flat tire, see (P. 6-3).

TIRE PRESSURE

Tire Pressure Monitoring System
(TPMS)

WARNING

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should con-
tact the electric medical equip-
ment manufacturer for the pos-
sible influences before use.

This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS).
It monitors tire pressure of all tires.
When the low tire pressure warning
light is lit, and the “Tire Pressure
Low - Add Air” warning appears on
the vehicle information display, one
or more of your tires is significantly
under-inflated.

LDI3243

Rear combination light

WHEELS AND TIRES

Do-it yourself

8-25

The TPMS will activate only when the
vehicle is driven at speeds above
16 mph (25 km/h). Also, this system
may not detect a sudden drop in tire
pressure (for example a flat tire while
driving).

For additional information, see “Low
tire pressure warning light” (P. 2-21),
“Tire Pressure Monitoring System
(TPMS)” (P. 5-4) and “Tire Pressure
Monitoring System (TPMS)” (P. 6-3).

Tire inflation pressure

Check the pressure of the tires often
and always prior to long distance
trips. The recommended tire pres-
sure specifications are shown on
the F.M.V.S.S/C.M.V.S.S certification
label or Tire and Loading Informa-
tion label under the “Cold Tire Pres-
sure” heading. The Tire and Loading
Information label is affixed to the

driver side center pillar. Tire pressures
should be checked regularly because:

• Most tires naturally lose air over

time.

• Tires can lose air suddenly when

driven over potholes or other ob-
jects or if the vehicle strikes a curb
while parking.

The

tire

pressures

should

checked when the tires are cold.
The tires are considered COLD after
the vehicle has been parked for 3 or
more hours, or driven less than 1 mile
(1.6 km) at moderate speeds.

The TPMS with Easy-Fill Tire Alert
also provides visual and audible sig-
nals outside the vehicle for inflating
the tires to the recommended COLD
tire pressure. For additional infor-
mation, see “TPMS with Easy-Fill Tire
Alert” (P. 5-7).

Incorrect tire pressure, including
under inflation, may adversely af-
fect tire life and vehicle handling.

WARNING

•

Improperly inflated tires can fail
suddenly and cause an accident.

•

The Gross Vehicle Weight rating
(GVWR)

located

the

F.M.V.S.S./C.M.V.S.S certification
label. The vehicle weight capac-
ity is indicated on the Tire and
Loading Information label. Do
not load your vehicle beyond
this capacity. Overloading your
vehicle may result in reduced
tire life, unsafe operating condi-
tions due to premature tire fail-
ure, or unfavorable handling
characteristics and could also
lead to a serious accident. Load-
ing beyond the specified capac-
ity may also result in failure of
other vehicle components.

8-26

Do-it yourself

•

Before taking a long trip, or
whenever

you

heavily

load

your vehicle, use a tire pressure
gauge to ensure that the tire
pressures are at the specified
level.

•

For additional information re-
garding tires, refer to “Impor-
tant Tire Safety Information”
(US) or “Tire Safety Informa-
tion” (Canada) in the Warranty
Information Booklet.

Tire and Loading Information
label

Seating capacity: The maximum

number of occupants that can be
seated in the vehicle.

Original size: The size of the tires

originally installed on the vehicle at
the factory.

Cold tire pressure: Inflate the tires

to this pressure when the tires are
cold. Tires are considered COLD af-
ter the vehicle has been parked for
3 or more hours, or driven less than
1 mile (1.6 km) at moderate speeds.
The recommended cold tire inflation
is set by the manufacturer to pro-
vide the best balance of tire wear, ve-
hicle handling, driveability, tire noise,
etc., up to the vehicle’s GVWR.

LDI2644

Do-it yourself

8-27

Tire size — see “Tire labeling”

(P. 8-29).

Spare tire size or compact spare

tire size (if so equipped)

Vehicle load limit: For additional

information, see “Vehicle loading in-
formation” (P. 10-11).

Checking tire pressure

1. Remove the valve stem cap from

the tire.

2. Press the pressure gauge se-

curely onto the valve stem. Do not
press too hard or force the valve
stem sideways, otherwise air will
escape. If the hissing sound of
air escaping from the tire is heard
while checking the pressure, re-
position the gauge to eliminate
this leakage.

3. Remove the gauge.

4. Read the tire pressure on the

gauge stem and compare it to
the specification shown on the Tire
and Loading Information label.

5. Add air to the tire as necessary.

If too much air is added, press the
core of the valve stem briefly with
the tip of the gauge stem to re-
lease pressure. Recheck the pres-
sure and add or release air as
necessary.

6. Install the valve stem cap.

7. Check the pressure of all of the

tires.

SDI1949

8-28

Do-it yourself

SIZE

COLD TIRE INFLATION
PRESSURE

psi

kPa

Front and
Rear Original
Tire P205/
55R16 89H

36 PSI

250 kPa,

Front and
Rear Original
Tire P215/
50R17 90V

36 PSI

250 kPa,

TIRE LABELING

Federal law requires tire manufac-
turers to place standardized infor-
mation on the sidewall of all tires.
This information identifies and de-
scribes the fundamental character-
istics of the tire and also provides the
Tire Identification Number (TIN) for
safety standard certification. The TIN
can be used to identify the tire in
case of a recall.

WDI0394

Example

Do-it yourself

8-29

Tire size (example: P215/65R15 95H)

1. P: The “P” indicates the tire is de-

signed for passenger vehicles (not
all tires have this information).

2. Three-digit number (215): This

number gives the width in milli-
meters of the tire from sidewall
edge to sidewall edge.

3. Two-digit number (65): This num-

ber, known as the aspect ratio,
gives the tire's ratio of height to
width.

4. R: The “R” stands for radial.

5. Two-digit number (15): This num-

ber is the wheel or rim diameter in
inches.

6. Two- or three-digit number (95):

This number is the tire's load index.
It is a measurement of how much
weight each tire can support.

7. H: Tire speed rating. You should not

drive the vehicle faster than the tire
speed rating.

WDI0395

Example

8-30

Do-it yourself

TIN (Tire Identification Number)

for a new tire (example: DOT XX XX
XXX XXXX)

1. DOT: Abbreviation for the “Depart-

ment Of Transportation”. The sym-
bol can be placed above, below or
to the left of the Tire Identification
Number.

2. Two-digit code: Manufacturer's

identification mark.

3. Two-digit code: Tire size.

4. Three-digit code: Tire type code

(Optional).

5. Four

numbers

represent

the

week and year the tire was built.
For example, the numbers 3103
means the 31st week of 2003. If
these numbers are missing then
look on the other sidewall of the
tire.

LDI3639

Example (Type A) (if so equipped)

Do-it yourself

8-31

TIN (Tire Identification Number)

for a new tire (example: DOT XXX
XXXXXX XXXX)

1. DOT: Abbreviation for the “Depart-

ment Of Transportation”. The sym-
bol can be placed above, below or
to the left or right of the Tire Identi-
fication Number.

2. Three-digit code: Manufacturer's

identification mark.

3. Six-digit code: Descriptive code

used to identify significant char-
acteristics of the tire.

4. Four numbers represent the week

and year the tire was built. For ex-
ample, the numbers 3103 means
the 31st week of 2003.

Tire ply composition and material

The number of layers or plies of
rubber-coated fabric in the tire. Tire
manufacturers also must indicate
the materials in the tire, which include
steel, nylon, polyester and others.

Maximum permissible inflation

pressure

This number is the greatest amount
of air pressure that should be put in
the tire. Do not exceed the maximum
permissible inflation pressure.

Maximum load rating

This number indicates the maxi-
mum load in kilograms and pounds
that can be carried by the tire. When
replacing the tires on the vehicle,
always use a tire that has the same
load rating as the factory installed
tire.

LDI2786

Example (Type B) (if so equipped)

8-32

Do-it yourself

Term of “tubeless” or “tube type”

Indicates whether the tire requires
an inner tube (“tube type”) or not
(“tubeless”).

The word “radial”

The word “radial” is shown if the tire
has radial structure.

Manufacturer or brand name

Manufacturer or brand name is
shown.

Other Tire-related Terminology

In addition to the many terms that
are defined throughout this section,
Intended Outboard Sidewall is (1)
the sidewall that contains a white-
wall, bears white lettering or bears
manufacturer, brand, and/or model
name molding that is higher or
deeper than the same molding on

the other sidewall of the tire, or (2)
the outward facing sidewall of an
asymmetrical tire that has a particu-
lar side that must always face out-
ward when mounted on a vehicle.

TYPES OF TIRES

WARNING

•

When changing or replacing tires,
be sure all four tires are of the same
type (Example: Summer, All Season
or Snow) and construction. A NISSAN
certified LEAF dealer may be able to
help you with information about tire
type, size, speed rating and avail-
ability.

•

Always use tires of the same type,
size, brand, construction and tread
pattern on all four wheels. Failure to
do so may result in a circumference
difference between tires on the front
and rear axles which can cause the
VDC system to malfunction resulting
in personal injury or death, excessive
tie wear and may damage the trans-
mission and differential gears.

•

Replacement

tires

may

have

lower speed rating than the factory
equipped tires, and may not match
the potential maximum vehicle speed.
Never exceed the maximum speed
rating of the tire.

•

Replacing tires with those not origi-
nally specified by NISSAN could affect
the proper operation of the TPMS.

•

For additional information regarding
tires, refer to “Important Tire Safety
Information” (US) or “Tire Safety In-
formation” (Canada) in the Warranty
Information Booklet.

All season tires

NISSAN specifies all season tires on some
models to provide good performance all
year, including snowy and icy road condi-
tions. All Season tires are identified by ALL
SEASON and/or M&S (Mud and Snow) on
the tire sidewall. Snow tires have better
snow traction than All Season tires and
may be more appropriate in some areas.

Do-it yourself

8-33

Nissan Leaf (2024 year). Manual in english - page 17