Nissan Sentra (2024 year). Manual in english

•

If the wheels are changed for any
reason, always replace with wheels
which have the same off-set dimen-
sion. Wheels of a different off-set
could cause premature tire wear, de-
grade vehicle handling characteris-
tics, affect the VDC system and/or in-
terference with the brake discs. Such
interference can lead to decreased
braking efficiency and/or early brake
pad/shoe wear. For additional infor-
mation on wheel-off set dimensions,
see “Wheels and tires” (P. 10-9).

•

When using a wheel without the
TPMS such as the spare tire, the TPMS
will not function and the low tire
pressure warning light will flash for
approximately 1 minute. The light will
remain on after 1 minute. Have your
tires replaced and/or TPMS system
reset as soon as possible. It is recom-
mended that you visit a NISSAN
dealer for this service.

•

Replacing tires with those not origi-
nally specified by NISSAN could af-
fect the proper operation of the
TPMS.

•

The TPMS sensor may be damaged if
it is not handled correctly. Be careful
when handling the TPMS sensor.

•

When replacing the TPMS sensor, the
ID registration may be required. Con-
tact

NISSAN

dealer

for

registration.

•

Do not use a valve stem cap that is
not specified by NISSAN. The valve
stem cap may become stuck.

•

Be sure that the valve stem caps are
correctly fitted. Otherwise the valve
may be clogged up with dirt and
cause

malfunction

loss

pressure.

•

Do not install a damaged or de-
formed wheel or tire even if it has
been repaired. Such wheels or tires
could have structural damage and
could fail without warning.

•

The use of retread tires is not
recommended.

•

For additional information regarding
tires, refer to “Important Tire Safety
Information” (US) or “Tire Safety In-
formation” (Canada) in the Warranty
Information Booklet.

Wheel balance

Unbalanced wheels may affect vehicle
handling and tire life. Even with regular use,
wheels can get out of balance. Therefore,
they should be balanced as required.

Wheel balance service should be per-
formed with the wheels off the vehicle.
Spin balancing the wheels on the vehicle
could lead to mechanical damage.

•

For additional information regarding
tires, refer to “Important Tire Safety In-
formation” (US) or “Tire Safety Informa-
tion” (Canada) in the Warranty Informa-
tion Booklet.

Care of wheels

• Wash the wheels when washing the ve-

hicle to maintain their appearance.

• Clean the inner side of the wheels when

the wheel is changed or the underside of
the vehicle is washed.

• Do not use abrasive cleaners when

washing the wheels.

• Inspect wheel rims regularly for dents or

corrosion. Such damage may cause loss
of pressure or poor seal at the tire bead.

• NISSAN recommends waxing the road

wheels to protect against road salt in ar-
eas where it is used during winter.

8-40

Do-it-yourself

Spare tire (TEMPORARY USE ONLY
spare tire)

When using a wheel without the TPMS such
as the spare tire, the TPMS will not function.

Observe the following precautions if the
TEMPORARY USE ONLY spare tire must be
used. Otherwise, your vehicle could be
damaged or involved in an accident:

WARNING

•

The spare tire should be used for
emergency use only. It should be re-
placed with the standard tire at the
first opportunity to avoid possible
tire or differential damage.

•

Drive carefully while the TEMPORARY
USE ONLY spare tire is installed. Avoid
sharp turns and abrupt braking while
driving.

•

Periodically check spare tire inflation
pressure. Always keep the pressure
of the TEMPORARY USE ONLY spare
tire at 420 kPa, 4.2 bar (60 psi).

•

With the TEMPORARY USE ONLY spare
tire installed do not drive the vehicle
at speeds faster than 50 mph (80
km/h).

•

When driving on roads covered with
snow or ice, the TEMPORARY USE
ONLY spare tire should be used on the
rear wheels and the original tire used
on the front wheels (drive wheels).

•

Tire tread of the TEMPORARY USE
ONLY spare tire will wear at a faster
rate than the standard tire. Replace
the spare tire as soon as the tread
wear indicators appear.

•

Do not use the spare tire on other
vehicles.

•

Do not use more than one spare tire
at the same time.

•

Do not tow a trailer when the TEMPO-
RARY USE ONLY spare tire is installed.

CAUTION

•

Do not use tire chains on a TEMPO-
RARY USE ONLY spare tire. Tire chains
will not fit properly and may cause
damage to the vehicle.

•

Because the TEMPORARY USE ONLY
spare tire is smaller than the original
tire, ground clearance is reduced. To
avoid damage to the vehicle, do not
drive over obstacles. Also, do not drive
the vehicle through an automatic car
wash since it may get caught.

Do-it-yourself

8-41

Some day-to-day and regular mainte-
nance is essential to maintain your vehi-
cle’s good mechanical condition, as well as
its emissions and engine performance.

It is the owner's responsibility to make sure
that the scheduled maintenance, as well as
general maintenance, is performed.

As the vehicle owner, you are the only one
who can ensure that your vehicle receives
proper maintenance. You are a vital link in
the maintenance chain.

GENERAL MAINTENANCE

General maintenance includes those items
which should be checked during normal
day-to-day operation. They are essential
for proper vehicle operation. It is your re-
sponsibility to perform these procedures
regularly as prescribed.

Performing general maintenance checks
requires minimal mechanical skill and only
a few general automotive tools.

These checks or inspections can be done
by yourself, a qualified technician or, if you
prefer, a NISSAN dealer.

SCHEDULED MAINTENANCE

The maintenance items listed in this sec-
tion are required to be serviced at regular
intervals. However under severe driving
conditions, additional or more frequent
maintenance will be required.

WHERE TO GO FOR SERVICE

If maintenance service is required or your
vehicle appears to malfunction, have the
systems checked and serviced. It is recom-
mended that you visit a NISSAN dealer for
this service.

NISSAN technicians are well-trained spe-
cialists and are kept up-to-date with the
latest service information through techni-
cal bulletins, service tips and training pro-
grams. They are fully qualified to work on
NISSAN vehicles

before

work begins.

If your vehicle is involved in a collision, it is
recommended that you ask your NISSAN
dealer where the nearest NISSAN Certified
Collision Center is located, or go to
http://collision.nissanusa.com.

You can be confident that a NISSAN deal-
er's service department can perform the
service needed to meet the maintenance
requirements on your vehicle.

During the normal day-to-day operation of
the vehicle, general maintenance should
be performed regularly as prescribed in
this section. If you detect any unusual
sounds, vibrations or smells, be sure to
check for the cause or have it checked
promptly. In addition, it is recommended
that you visit a NISSAN dealer if you think
that repairs are required.

When performing any checks or mainte-
nance work, see “Maintenance precau-
tions” (P. 8-2).

EXPLANATION OF GENERAL
MAINTENANCE ITEMS

WARNING

Failure to follow the procedures listed
within this section may result in per-
sonal injury.

Additional information on the following
items with “ * ” is found in the “Do-it-
yourself ” section of this manual.

Outside the vehicle

The maintenance items listed here should
be performed from time to time, unless
otherwise specified.

MAINTENANCE REQUIREMENTS

GENERAL MAINTENANCE

9-2

Maintenance and schedules

Doors and engine hood:

Check that the

doors and engine hood operate properly.
Also ensure that all latches lock securely.
Lubricate hinges, latches, latch pins, rollers
and links if necessary. Make sure that the
secondary latch keeps the hood from
opening

when

the

primary

latch

released.

When driving in areas using road salt or
other corrosive materials, check lubrica-
tion frequently.

Check that the gas stays or struts properly
and securely hold the hood, trunk, or rear
hatch fully open. If the hood, trunk, or rear
hatch is not held open, have the gas stays
or struts replaced.

Lights*:

Clean the headlights on a regular

basis. Make sure that the headlights, stop
lights, tail lights, turn signal lights, and other
lights are all operating properly and in-
stalled securely. Also check headlight aim.

Road wheel nuts (lug nuts)*:

When check-

ing the tires, make sure no wheel nuts are
missing, and check for any loose wheel
nuts. Tighten if necessary.

Tire rotation*:

Rotate tires at the specified

interval

shown

the

maintenance

schedule.

Tires*:

Check the pressure with a gauge

often and always prior to long distance
trips. If necessary, adjust the pressure in all
tires, including the spare, to the pressure
specified. Check carefully for damage, cuts
or excessive wear.

Tire Pressure Monitoring System (TPMS)
tire pressure sensor:

It is recommended

that you replace the tire pressure sensor
assembly when the tires are replaced due
to wear or age.

Wheel alignment and balance:

If the ve-

hicle should pull to either side while driving
on a straight and level road, or if you detect
uneven or abnormal tire wear, there may
be a need for wheel alignment. If the steer-
ing wheel or seat vibrates at normal high-
way speeds, wheel balancing may be
needed.

For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada) in
the Warranty Information Booklet.

Windshield:

Clean the windshield on a

regular basis. Check the windshield at least
every six months for cracks or other dam-
age. Have a damaged windshield repaired
by a qualified repair facility. It is recom-
mended that you have a damaged wind-

shield repaired by a NISSAN dealer, or a
NISSAN Certified Collision Center. To locate
a collision center in your area, refer to
http://collision.nissanusa.com.

Windshield wiper blades*:

Check for

cracks or wear if they do not wipe properly.

Inside the vehicle

The maintenance items listed here should
be checked on a regular basis, such as
when performing scheduled maintenance,
cleaning the vehicle, etc.

Accelerator pedal:

Check the pedal for

smooth operation and make sure the
pedal does not catch or require uneven
effort. Keep the floor mat away from the
pedal.

Brake pedal:

Check the pedal for smooth

operation. If the brake pedal suddenly goes
down further than normal, the pedal feels
spongy or the vehicle seems to take longer
to stop, have your vehicle checked imme-
diately. It is recommended that you visit a
NISSAN dealer for this service. Keep the
floor mat away from the pedal.

Brakes:

Check that the brakes do not pull

the vehicle to one side when applied.

Maintenance and schedules

9-3

Continuously

Variable

Transmission

(CVT) P (Park) position mechanism (if so
equipped):

On a fairly steep hill check that

the vehicle is held securely with the shift
lever in the P (Park) position without apply-
ing any brakes.

Parking brake:

Check the parking brake

operation regularly. The vehicle should be
securely held on a fairly steep hill with only
the parking brake applied. If the parking
brake needs adjustment, it is recom-
mended that you visit a NISSAN dealer for
this service.

Seats:

Check seat position controls such

as seat adjusters, seatback recliner, etc., to
ensure they operate smoothly and all
latches lock securely in every position.
Check that the head restraints/headrests
move up and down smoothly and the locks
(if so equipped) hold securely in all latched
positions.

Seat belts:

Check that all parts of the seat

belt system (for example, buckles, anchors,
adjusters and retractors) operate properly
and smoothly, and are installed securely.
Check the belt webbing for cuts, fraying,
wear or damage.

Steering wheel:

Check for changes in the

steering system, such as excessive free
play, hard steering or strange noises.

Warning lights and chimes:

Make sure all

warning lights and chimes are operating
properly.

Windshield defroster:

Check that the air

comes out of the defroster outlets properly
and in sufficient quantity when operating
the heater or air conditioner.

Windshield wiper and washer*:

Check

that the wipers and washer operate prop-
erly and that the wipers do not streak.

Under the hood and vehicle

The maintenance items listed here should
be checked periodically (for example, each
time you check the engine oil or refuel).

Battery*:

This vehicle is equipped with a

sealed maintenance free battery. It is rec-
ommended that you visit a NISSAN dealer
for service.

NOTE:

Care should be taken to avoid situations
that can lead to potential battery dis-
charge and potential no-start conditions
such as:

1. Installation or extended use of elec-

tronic accessories that consume bat-
tery power when the engine is not
running (Phone chargers, GPS, DVD
players, etc.).

2. Vehicle is not driven regularly and/or

only driven short distances.

In these cases, the battery may need to
be charged to maintain battery health.

Brake and clutch (if so equipped) fluid
level*:

Make sure that the brake and clutch

fluid levels are between the MIN and MAX
lines on the reservoir.

Engine coolant level*:

Check the coolant

level when the engine is cold.

Engine drive belts*:

Make sure the drive

belt is not frayed, worn, cracked or oily.

Engine oil level*:

Check the level after

parking the vehicle on a level surface with
the engine off. Wait more than 15 minutes
for the oil to drain back into the oil pan.

9-4

Maintenance and schedules

Exhaust system:

Make sure there are no

loose supports, cracks or holes. If the
sound of the exhaust seems unusual or
there is a smell of exhaust fumes, immedi-
ately have the exhaust system inspected. It
is recommended that you visit a NISSAN
dealer for this service. For additional infor-
mation, see “Exhaust gas (carbon monox-
ide)” (P. 5-4).

Fluid leaks:

Check under the vehicle for

fuel, oil, water or other fluid leaks after the
vehicle has been parked for a while. Water
dripping from the air conditioner after use
is normal. If you should notice any leaks or if
fuel fumes are evident, check for the cause
and have it corrected immediately.

Radiator and hoses:

Check the front of the

radiator and clean off any dirt, insects,
leaves, etc., that may have accumulated.
Make sure the hoses have no cracks, defor-
mation, rot or loose connections.

Underbody:

The underbody is frequently

exposed to corrosive substances such as
those used on icy roads or to control dust. It
is very important to remove these sub-
stances from the underbody, otherwise
rust may form on the floor pan, frame, fuel
lines and exhaust system. At the end of
winter, the underbody should be thor-
oughly flushed with plain water, in those
areas where mud and dirt may have accu-
mulated. For additional information, see
“Cleaning exterior” (P. 7-2).

Windshield-washer fluid*:

Check that

there is adequate fluid in the reservoir.

The following descriptions are provided to
give you a better understanding of the
scheduled maintenance items that should
be regularly checked or replaced. The
maintenance schedule indicates at which
mileage/time intervals each item requires
service.

In addition to scheduled maintenance,
your vehicle requires that some items be
checked during normal day-to-day opera-
tion. For additional information, see “Gen-
eral maintenance” (P. 9-2).

Items marked with

“*”

are recommended

by NISSAN for reliable vehicle operation.

You are not required to perform mainte-
nance on these items in order to maintain
the warranties which come with your
NISSAN. Other maintenance items and in-
tervals are required.

When applicable, additional information
can be found in the “Do-it-yourself ” section
of this manual.

EXPLANATION OF SCHEDULED
MAINTENANCE ITEMS

Maintenance and schedules

9-5

NOTE:

NISSAN does not advocate the se of non-
OEM approved aftermarket flushing sys-
tems and strongly advises against per-
forming

these

services

NISSAN

products. Many of the aftermarket flush-
ing systems use non-OEM approved
chemicals or solvents, the use of which
has not been validated by NISSAN.
For recommended fuel, lubricants, fluids,
grease, and refrigerant, see “Recom-
mended fluids/lubricants and capaci-
ties” (P. 10-2)

EMISSION CONTROL SYSTEM
MAINTENANCE:

Air cleaner filter:

Replace at specified in-

tervals. When driving for prolonged periods
in dusty conditions, check/replace the filter
more frequently.

Engine drive belts*:

Check engine drive

belt for wear, fraying or cracking and for
proper tension. Replace any damaged
drive belt.

Engine coolant*:

Replace coolant at the

specified interval. When adding or replac-
ing coolant, be sure to use only Genuine
NISSAN Long Life Antifreeze/Coolant (blue)
or equivalent with the proper mixture. (For

additional information on the proper mix-
ture for your area, see “Engine cooling sys-
tem” (P. 8-4).

NOTE: Mixing any other type of coolant
or the use of non-distilled water may re-
duce the recommended service interval
of the coolant.

Engine oil and oil filter:

Replace engine oil

and oil filter at the specified intervals. For
recommended oil grade and viscosity see
“Recommended fluids/lubricants and ca-
pacities” (P. 10-2).

Engine valve clearance*:

Inspect only if

valve noise increases. Adjust valve clear-
ance if necessary.

Fuel filter:

Periodic maintenance is not re-

quired. (in-tank type filter)

Fuel lines/connections*:

Check the fuel

hoses, piping and connections for leaks,
looseness, or deterioration. Tighten con-
nections or replace parts as necessary.

Fuel tank vapor vent system*:

Check va-

por lines for leaks or looseness. Tighten
connections or replace parts as necessary.

Spark plugs:

Replace at specified intervals.

Install new plugs of the type as originally
equipped.

CHASSIS AND BODY
MAINTENANCE:

Brake lines and cables:

Visually inspect for

proper installation. Check for chafing,
cracks, deterioration, and signs of leaking.
Replace any deteriorated or damaged
parts immediately.

Brake pads, rotors, drums and linings:

Check for wear, deterioration and fluid
leaks. Replace any deteriorated or dam-
aged parts immediately.

Exhaust system:

Visually inspect the ex-

haust pipes, muffler and hangers for leaks,
cracks, deterioration, and damage. Tighten
connections or replace parts as necessary.

In-cabin microfilter:

Replace at specified

intervals. When driving for prolonged peri-
ods in dusty conditions, replace the filter
more frequently.

Steering gear and linkage, axle and sus-
pension parts, drive shaft boots:

Check

for damage, looseness, and leakage of oil
or grease. Under severe driving conditions,
inspect more frequently.

Tire rotation:

Rotate tires at the specified

interval shown in the maintenance sched-
ule. When rotating tires, check for damage
and uneven wear. Replace if necessary.

9-6

Maintenance and schedules

Transmission fluid/oil:

Visually inspect for

signs of leakage at specified intervals. If
using a car-top carrier, or driving on rough
or muddy roads:
• Replace the manual transaxle gear oil ev-

ery 20,000 miles or 24 months.

• Replace the CVT fluid every 60,000 miles

(96,000 km) or request the dealer to in-
spect the fluid deterioration data using a
CONSULT. If the deterioration data is
more than 210000, replace the CVT fluid.

To help ensure smooth, safe and economi-
cal driving, NISSAN provides two mainte-
nance schedules that may be used, de-
pending upon the conditions in which you
usually drive. These schedules contain
both distance and time intervals, up to
120,000 miles (192,000 km)/144 months. For
most people, the odometer reading will in-
dicate when service is needed. However, if
you drive very little, your vehicle should be
serviced at the regular time intervals
shown in the schedule.

After 120,000 miles (192,000 km)/144
months, continue maintenance at the
same mileage/time intervals.

ADDITIONAL MAINTENANCE ITEMS
FOR SEVERE OPERATING
CONDITIONS

Additional maintenance items for severe
operating conditions

should be per-

formed on vehicles that are driven under
especially demanding conditions. Addi-
tional maintenance items should be per-
formed if you primarily operate your vehicle
under the following conditions:
• Repeated short trips of less than 5 miles

(8 km).

• Repeated short trips of less than 10 miles

(16 km) with outside temperatures re-
maining below freezing.

• Operating in hot weather in stop-and-go

“rush hour” traffic.

• Extensive idling and/or low speed driving

for long distances, such as police, taxi or
door-to-door delivery use.

• Driving in dusty conditions.
• Driving on rough, muddy or salt spread

roads.

• Using a car-top carrier.

If your vehicle is mainly operated under the
severe conditions, follow the severe use
maintenance intervals shown in the main-
tenance schedule.

MAINTENANCE SCHEDULES

Maintenance and schedules

9-7

OIL CONTROL SYSTEM

Your vehicle is equipped with oil control system. It calculates engine oil and filter change intervals based on driving conditions. Driving in
the following severe conditions will shorten the engine oil and filter change interval.

How driving conditions affect OCS display timing

Conditions

Driving Scene

Display timing

Light

• Freeway driving
• City driving (flat/moderate hills)
• No towing or heavy loads
• No extended engine idling

Normal

Extreme

• Repeated short trips of less than 5 miles (8 km).
• Repeated short trips of less than 10 miles (16 km) with outside temperatures remaining

below freezing.

• Operating in hot weather in stop-and-go “rush hour” traffic.
• Extensive idling and/or low speed driving for long distances, such as police, taxi or door-to-

door delivery use.

• Using a car-top carrier.
• Driving with frequent use of braking or in mountainous areas.
• Sustained high speed driving.

Early

CAUTION

•

If the oil replacement indicator is dis-
played, change the engine oil within
two weeks or less than 500 miles
(800 km).

•

Operating your vehicle with deterio-
rated oil can damage the engine.

•

If your oil replacement indicator re-
sets prematurely or becomes inop-
erative, please change the oil within
six months or 5,000 miles (8,000 km)
from your last oil change.

9-8

Maintenance and schedules

2.0L 4 CYLINDER (MR20DD engine
model)

The following shows the maintenance
schedule.

Choose

the

maintenance

schedule

needed based on your vehicle driving
conditions.

After 120,000 miles (192,000 km)/144
months, continue maintenance at the
same mileage/time interval.

5,000 miles/(8,000 km)/6 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

10,000 miles/(16,000 km)/
12 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Brake lines & cables
• Brake pads & rotors
• CVT fluid
• Drive shaft boots
• Manual transmission gear oil
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace engine oil & filter (1)
• Tire rotation

Maintenance and schedules

9-9

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Drive shaft boots
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

15,000 miles/(24,000 km)/
18 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspection:
• Intelligent key battery
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace in-cabin microfilter
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

20,000 miles/(32,000 km)/
24 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Brake lines & cables
• Brake pads & rotors
• CVT fluid
• Fuel tank vapor vent system*
• Fuel lines/connections*
• Exhaust system
• Steering gear and linkage
• Axle & suspension parts
• Drive shaft boots
• Manual transmission gear oil
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

9-10

Maintenance and schedules

Essentials:
• Replace brake fluid
• Replace engine oil & filter (1)
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Drive shaft boots
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace manual transmission gear oil
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

* Maintenance items and intervals with “*”
are recommended by NISSAN for reliable
vehicle operation. The owner need not per-
form such maintenance in order to main-
tain the emission warranty or manufac-
turer recall liability. Other maintenance
items and intervals are required.

25,000 miles/(40,000 km)/
30 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

30,000 miles/(48,000 km)/
36 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Brake lines & cables
• Brake pads & rotors
• CVT fluid
• Drive shaft boots
• Manual transmission gear oil
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace air cleaner filter (1)
• Replace engine oil & filter (2)
• Replace in-cabin microfilter
• Replace Intelligent key battery
• Tire rotation

Maintenance and schedules

9-11

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Drive shaft boots
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace brake fluid

(1) If operating mainly in dusty conditions,
more

frequent

maintenance

may

required.

(2) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

35,000 miles/(56,000 km)/
42 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

40,000 miles/(64,000 km)/
48 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Brake lines & cables
• Brake pads & rotors
• CVT fluid
• Engine drive belts*
• Fuel tank vapor vent system*
• Fuel lines/connections*
• Exhaust system
• Steering gear and linkage
• Axle & suspension part
• Drive shaft boots
• Manual transmission gear oil
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose Inspection
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

9-12

Maintenance and schedules

Essentials:
• Replace brake fluid
• Replace engine oil & filter (1)
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Drive shaft boots
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace manual transmission gear oil
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

45,000 miles/(72,000 km)/
54 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace in-cabin microfilter
• Replace Intelligent key battery
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

50,000 miles/(80,000 km)/
60 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Brake lines & cables
• Brake pads & rotors
• CVT fluid
• Engine drive belts*
• Drive shaft boots
• Manual transmission gear oil
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspections
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace engine oil & filter (1)
• Tire rotation

Maintenance and schedules

9-13

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Drive shaft boots
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

55,000 miles/(88,000 km)/
66 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

60,000 miles/(96,000 km)/
72 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspection
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

9-14

Maintenance and schedules

Essentials:
• Replace air cleaner filter (1)
• Replace brake fluid
• Replace engine oil & filter (2)
• Replace in-cabin microfilter
• Replace Intelligent key battery
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Drive shaft boots
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace CVT fluid
• Replace manual transmission gear oil
• Replace brake fluid

(1) If operating mainly in dusty conditions,
more

frequent

maintenance

may

required.

(2) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

65,000 miles/(104,000 km)/
78 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

Maintenance and schedules

9-15

70,000 miles/(112,000 km)/
84 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspections
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace engine oil & filter (1)
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Drive shaft boots
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

75,000 miles/(120,000 km)/
90 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace in-cabin microfilter
• Replace Intelligent key battery
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

9-16

Maintenance and schedules

80,000 miles/(128,000 km)/
96 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspections
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace brake fluid
• Replace engine oil & filter (1)
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Drive shaft boots
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace manual transmission gear oil
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

85,000 miles/(136,000 km)/
102 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

Maintenance and schedules

9-17

90,000 miles/(144,000 km)/
108 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspections
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace air cleaner filter (1)
• Replace engine oil & filter (2)
• Replace in-cabin microfilter
• Replace Intelligent key battery
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Drive shaft boots
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace brake fluid

(1) If operating mainly in dusty conditions,
more

frequent

maintenance

may

required.

(2) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

9-18

Maintenance and schedules

95,000 miles/(152,000 km)/
114 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

100,000 miles/(160,000 km)/
120 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspections
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace brake fluid
• Replace engine oil & filter (1)
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Drive shaft boots
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace manual transmission gear oil
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

Maintenance and schedules

9-19

105,000 miles/(168,000 km)/
126 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace in-cabin microfilter
• Replace Intelligent key battery
• Tire rotation
• Replace spark plugs
• Replace engine coolant * (1)

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

(1) First replacement interval is 105,000
miles (168,000 km) or 84 months. After first
replacement, replace every 75,000 miles
(120,000 km) or 60 months.

* Maintenance items and intervals with “ * ”
are recommended by NISSAN for reliable
vehicle operation. The owner need not per-
form such maintenance in order to main-
tain the emission warranty or manufac-
turer recall liability. Other maintenance
items and intervals are required.

110,000 miles/(176,000 km)/
132 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspections
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Replace engine oil & filter (1)
• Tire rotation

9-20

Maintenance and schedules

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Drive shaft boots
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace brake fluid

(1) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

115,000 miles/(184,000 km)/
138 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

Inspections:
• Horn, lights, signals, wipers, rear hatch/

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Essentials:
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Steering gear & linkage
• Axle & suspension parts
• Drive shaft boots

120,000 miles/(192,000 km)/
144 months

Perform at number of miles, kilometers or
months, whichever comes first.

Standard maintenance:

hood lift supports

• All fluids inspected (engine, wiper, brake,

power steering, coolant)

• Hose inspections
• Suspension components (shocks, sub-

frame, tie rods)

• Battery terminals and cables, battery test
• Tire pressure, treadwear and depth

Maintenance and schedules

9-21

Essentials:
• Replace air cleaner filter (1)
• Replace brake fluid
• Replace engine oil & filter (2)
• Replace in-cabin microfilter
• Replace Intelligent key battery
• Tire rotation

Severe use maintenance:

Inspections:
• Brake pads & rotors
• Exhaust system
• Drive shaft boots
• Steering gear & linkage
• Axle & suspension parts

Essentials:
• Replace CVT fluid
• Replace manual transmission gear oil
• Replace brake fluid

(1) If operating mainly in dusty conditions,
more

frequent

maintenance

may

required.

(2) If the oil replacement indicator is dis-
played, change the engine oil and filter
within two weeks or less than 500 miles
(800 km).

9-22

Maintenance and schedules

The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure
described in the “Do-it-yourself ” section to determine the proper refill capacity.

Fluid Type

Capacity (approximate)

Recommended Fluids/Lubricants

Metric

Measure

Imperial

Measure

Fuel

47 L

12-3/8 gal

10 3/8 gal

• For additional information, see “Fuel recommenda-
tion” (P. 10-4).

Engine oil*1
Drain and refill
*1 For additional informa-
tion, see “Engine oil”
(P. 8-6 ).

With oil filter

change

4.1 L

4-3/8 qt

3-5/8 qt

• Genuine “NISSAN Motor Oil 0W-20 SP” (or equivalent)
is recommended.
• If the above motor oil (or engine oil) is not available,
a synthetic 0W-20 GF-6 SP motor oil (or engine oil)
may be used. Damage caused by the use of motor
oil (or engine oil) other than as recommended is not
covered under NISSAN’s New Vehicle Limited War-
ranty. For additional information, see “Engine oil and
oil filter recommendations” (P. 10-6).

Without oil fil-

ter change

3.8 L

4 qt

3-3/8 qt

Engine coolant
with reservoir

With manual

transmission

6.9 L

1-7/8 gal

1-1/2 gal

• Pre-diluted Genuine NISSAN Long Life Antifreeze/
Coolant (blue) or equivalent.

With continu-

ously variable

transmission

7.1 L

1-7/8 gal

1-1/2 gal

Manual transmission fluid

—

• Genuine NISSAN Manual Transmission Fluid (MTF)
TL/JR Type 75W-75, or equivalent.
• If Genuine NISSAN Manual Transmission Fluid (MTF)
TL/JR Type is not available, API GL-4+, Viscosity SAE
75W-75 may be used as a temporary replacement.
However, use Genuine NISSAN Manual Transmission
Fluid (MTF) TL/JR Type as soon as it is available.

RECOMMENDED FLUIDS/
LUBRICANTS AND CAPACITIES

10-2

Technical and consumer information

Fluid Type

Capacity (approximate)

Recommended Fluids/Lubricants

Metric

Measure

Imperial

Measure

Continuously Variable Transmission (CVT)
fluid

—

• Genuine NISSAN CVT Fluid NS-3.
• NISSAN recommends using Genuine NISSAN CVT
Fluid NS-3 (or equivalent) ONLY in NISSAN CVTs. Do
not mix with other fluids. Using fluids that are not
equivalent to Genuine NISSAN CVT Fluid NS-3 may
damage the CVT. Damage caused by the use of
fluids other than as recommended is not covered
under NISSAN's New Vehicle Limited Warranty out-
lined in your Warranty Information Booklet.

Brake and clutch (if so equipped) fluid

—

• Genuine NISSAN Brake Fluid or equivalent DOT 3 or
DOT 4

Multi-purpose grease

—

• NLGI No. 2 (lithium soap base)

Air conditioning system refrigerant

—

• HFO-1234yf (R-1234yf)
• For additional information, see “Air conditioner sys-
tem refrigerant and oil recommendations” (P. 10-7).

Air conditioning system oil

—

• Genuine NISSAN A/C System Oil Type PAG or
equivalent
• For additional information, see “Air conditioner sys-
tem refrigerant and oil recommendations” (P. 10-7).

Windshield-washer fluid

USA

2.5 L

5/8 gal

1/2 gal

• Genuine NISSAN Windshield Washer Concentrate
Cleaner & Antifreeze fluid or equivalent

Canada

4.2 L

1-1/8 gal

7/8 gal

Technical and consumer information

10-3

FUEL RECOMMENDATION

Use unleaded regular gasoline with an oc-
tane rating of at least 87 AKI (Anti-Knock
Index) number (Research octane number
91).

CAUTION

•

Only vehicles with the E-85 filler door
label can operate on E-85. Fuel sys-
tem or other damage can occur if
E-85 is used in vehicles that are not
designed to run on E-85.

•

Using a fuel other than that specified
could adversely affect the emission
control system, and may also affect
the warranty coverage.

•

Under no circumstances should a
leaded gasoline be used, because
this

will

damage

the

three-way

catalyst.

•

Do not use E-15 or E-85 fuel in your
vehicle. Your vehicle is not designed
to run on E-15 or E-85 fuel. Using E-15
or E-85 fuel in a vehicle not specifi-
cally designed for E-15 or E-85 fuel
can adversely affect the emission
control devices and systems of the
vehicle. Damage caused by such fuel
is not covered by the NISSAN New Ve-
hicle Limited Warranty.

•

Do not use fuel that contains the oc-
tane booster methylcyclopentadi-
enyl manganese tricarbonyl (MMT).
Using fuel containing MMT may ad-
versely affect vehicle performance
and vehicle emissions. Not all fuel
dispensers are labeled to indicate
MMT content, so you may have to
consult your gasoline retailer for
more details. Note that Federal and
California laws prohibit the use of
MMT in reformulated gasoline.

•

U.S. government regulations require
ethanol dispensing pumps to be
identified by a small, square, orange
and black label with the common ab-
breviation or the appropriate per-
centage for that region.

Gasoline specifications

NISSAN recommends using gasoline that
meets the World-Wide Fuel Charter (WWFC)
specifications where it is available. Many of
the automobile manufacturers developed
this specification to improve emission con-
trol system and vehicle performance. Ask
your service station manager if the gaso-
line meets the WWFC specifications.

Reformulated gasoline

Some fuel suppliers are now producing re-
formulated gasolines. These gasolines are
specially designed to reduce vehicle emis-
sions. NISSAN supports efforts towards
cleaner air and suggests that you use re-
formulated gasoline when available.

Gasoline containing oxygenates

Some fuel suppliers sell gasoline contain-
ing oxygenates such as ethanol, Methyl
Tert-butyl Ether (MTBE) and methanol with
or without advertising their presence.
NISSAN does not recommend the use of
fuels of which the oxygenate content and
the fuel compatibility for your NISSAN can-
not be readily determined. If in doubt, ask
your service station manager.

10-4

Technical and consumer information

you

use

oxygenate-blend

gasoline,

please take the following precautions as
the usage of such fuels may cause vehicle
performance problems and/or fuel system
damage.
•

The fuel should be unleaded and have
an octane rating no lower than that
recommended for unleaded gasoline.

•

oxygenate-blend

other

than

methanol blend is used, it should con-
tain no more than 10% oxygenate.
(MTBE may, however, be added up to
15%.)

•

E-15 fuel contains more than 10% oxy-
genate. E-15 fuel will adversely affect
the emission control devices and sys-
tems of the vehicle and should not be
used. Damage caused by such fuel is
not covered by the NISSAN New Vehicle
Limited Warranty.

•

If a methanol blend is used, it should
contain no more than 5% methanol
(methyl

alcohol,

wood

alcohol).

should also contain a suitable amount
of appropriate cosolvents and corro-
sion inhibitors. If not properly formu-
lated with appropriate cosolvents and
corrosion inhibitors, such methanol
blends may cause fuel system damage
and/or vehicle performance problems.

At this time, sufficient data is not avail-
able to ensure that all methanol blends
are suitable for use in NISSAN vehicles.

If any driveability problems such as engine
stalling and difficult hot-starting are expe-
rienced after using oxygenate-blend fuels,
immediately change to a non-oxygenate
fuel or a fuel with a low blend of MTBE.

Take care not to spill gasoline during re-
fueling. Gasoline containing oxygenates
can cause paint damage.

E–15 fuel

E-15 fuel is a mixture of approximately 15%
fuel ethanol and 85% unleaded gasoline.
E-15 can only be used in vehicles designed
to run on E-15 fuel. Do not use E-15 in your
vehicle. U.S. government regulations re-
quire fuel ethanol dispensing pumps to be
identified with small, square, orange and
black label with the common abbreviation
or the appropriate percentage for that
region.

E–85 fuel

E-85 fuel is a mixture of approximately 85%
fuel ethanol and 15% unleaded gasoline.
E-85 can only be used in a Flexible Fuel
Vehicle (FFV). Do not use E-85 in your ve-

hicle. U.S. government regulations require
fuel ethanol dispensing pumps to be iden-
tified by a small, square, orange and black
label with the common abbreviation or the
appropriate percentage for that region.

Fuel containing MMT

MMT, or methylcyclopentadienyl manga-
nese tricarbonyl, is an octane boosting ad-
ditive. NISSAN does not recommend the
use of fuel containing MMT. Such fuel may
adversely affect vehicle performance, in-
cluding the emissions control system. Note
that while some fuel pumps label MMT
content, not all do, so you may have to
consult your gasoline retailer for more
details.

Aftermarket fuel additives

NISSAN does not recommend the use of
any aftermarket fuel additives (for ex-
ample,

fuel

injector

cleaner,

octane

booster, intake valve deposit removers,
etc.) which are sold commercially. Many of
these additives intended for gum, varnish
or deposit removal may contain active sol-
vents or similar ingredients that can be
harmful to the fuel system and engine.

Technical and consumer information

10-5

Octane rating tips

Using unleaded gasoline with an octane
rating lower than recommended can
cause persistent, heavy “spark knock.”
(“Spark knock” is a metallic rapping
noise.) If severe, this can lead to engine
damage. If you detect a persistent heavy
spark knock even when using gasoline
of the stated octane rating, or if you hear
steady spark knock while holding a
steady speed on level roads, it is recom-
mended that you have a NISSAN dealer
correct the condition. Failure to correct
the condition is misuse of the vehicle, for
which NISSAN is not responsible.

Incorrect ignition timing may result in
spark knock, after-run and/or overheating,
which may cause excessive fuel consump-
tion or engine damage. If any of the above
symptoms are encountered, have your ve-
hicle checked. It is recommended that you
visit a NISSAN dealer for servicing.

However, now and then you may notice
light spark knock for a short time while
accelerating or driving up hills. This is not
a cause for concern, because you get the
greatest fuel benefit when there is light
spark knock for a short time under heavy
engine load.

ENGINE OIL AND OIL FILTER
RECOMMENDATIONS

Selecting the correct oil

It is essential to choose the correct grade,
quality and viscosity engine oil to ensure
satisfactory engine life and performance.
For additional information, see “Recom-
mended fluids/lubricants and capacities”
(P. 10-2). NISSAN recommends the use of an
energy conserving oil in order to improve
fuel economy.

Select only engine oils that meet the Ameri-
can Petroleum Institute (API) certification or
International Lubricant Standardization and

Approval Committee (ILSAC) certification
and SAE viscosity standard. These oils have
the API certification mark on the front of the
container. Oils which do not have the speci-
fied quality label should not be used as they
could cause engine damage.

Oil additives

NISSAN does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used
and maintenance intervals are followed.

Oil which may contain foreign matter or
has been previously used should not be
used.

LTI2587

10-6

Technical and consumer information

Oil viscosity

The engine oil viscosity or thickness
changes with temperature. Because of
this, it is important to select the engine oil
viscosity based on the temperatures at
which the vehicle will be operated before
the next oil change. Choosing an oil viscos-
ity other than that recommended could
cause serious engine damage.

Selecting the correct oil filter

Your new NISSAN vehicle is equipped with a
high-quality Genuine NISSAN oil filter. When
replacing, use a Genuine NISSAN oil filter or
its equivalent for the reason described in
“Change intervals.”

Change intervals

The oil and oil filter change intervals for
your engine are based on the use of the
specified quality oils and filters. Using en-
gine oil and filters that are not of the speci-
fied quality, or exceeding recommended oil
and filter change intervals could reduce
engine life. Damage to the engine caused
by improper maintenance or use of incor-
rect oil and filter quality and/or viscosity is
not covered by the NISSAN New Vehicle
Limited Warranty.

Your engine was filled with a high-quality
engine oil when it was built. You do not have
to change the oil before the first recom-
mended change interval. Oil and filter
change intervals depend upon how you
use your vehicle.

Operation under the following conditions
may require more frequent oil and filter
changes:
• repeated short distance driving at cold

outside temperatures

• driving in dusty conditions
• extensive idling
• stop and go commuting

For additional information, refer to the
“Maintenance and schedules” section of
this manual.

AIR CONDITIONER SYSTEM
REFRIGERANT AND OIL
RECOMMENDATIONS

The air conditioner system in your
NISSAN vehicle must be charged with the
refrigerant HFO-1234yf (R-1234yf) and
NISSAN A/C system oil Type PAG or the
exact equivalents.

CAUTION

The use of any other refrigerant or oil
may cause severe damage to the air
conditioning system and will require
the replacement of all air conditioner
system components.

The refrigerant HFO-1234yf (R-1234yf) in
your NISSAN vehicle does not harm the
earth's ozone layer. Although this refriger-
ant does not affect the earth's atmo-
sphere, certain government regulations re-
quire the recovery and recycling of any
refrigerant during automotive air condi-
tioner system service. Air conditioner sys-
tem should only be serviced by trained and
certified technicians to ensure proper and
safe operation (SAE J2845). A NISSAN dealer
has the trained technicians and equip-
ment needed to recover and recycle your
air conditioner system refrigerant. Only
new and SAEJ2842 certified evaporator(s)
shall be used as replacement parts.

A damaged or leaking air conditioning
evaporator shall never be repaired or re-
placed with one removed from a used or
salvaged vehicle. To replace a damaged or
leaking evaporator, use only new and SAE
J2842 certified evaporator(s). It is recom-
mended that you visit a NISSAN dealer when
servicing your air conditioner system.

Technical and consumer information

10-7

ENGINE

Model

2.0L 4 cylinder (MR20DD engine model)

Type

Gasoline, 4-cycle, DOHC

Cylinder arrangement

4-cylinder, inline

Bore x Stroke

Metric measure

84.0 mm x 90.1 mm

US measure

3.307 in x 3.547 in

Displacement

Metric measure

1,997 cm

US measure

121.86 cu in

Firing order

1–3–4–2

Idle speed

No adjustment is necessary.

M/T

CVT in N (Neutral) position

Ignition timing (degree B.T.D.C. at idle speed)

CO % at idle

Spark plug

DXE22H11C

Spark plug gap (Nominal)

Metric measure

1.1 mm

US measure

0.043 in

Camshaft operation

Timing chain

This spark ignition system complies with the Canadian standard ICES-002.

SPECIFICATIONS

10-8

Technical and consumer information

WHEELS AND TIRES

Wheel type

Offset
Metric
Measure

Offset
US
Measure

Size

Steel

40 mm

1.57 in

16 x 6.5JJ

Aluminum

40 mm

1.57 in

16 x 6.5J

Aluminum

48 mm

1.89 in

17 x 7J

Aluminum

43 mm

1.69 in

18 x 7.5J

T-type (Steel
spare)

30 mm

1.18 in

16 x 4T

Tire size

205/60R16

215/50R17

215/45R18

Spare tire

T125/70D16

DIMENSIONS AND WEIGHTS

Metric
Mea-
sure

US
Measure

Overall
length

4,646
mm

182.9 in

Overall
width

1,816
mm

71.5 in

Overall
height

USA

S, SV

16 inch
wheel

1,447
mm

56.9 in

17 inch
wheel

1,447
mm

56.9 in

18 inch
wheel

1,449
mm

57.0 in

Canada

S, SV

M/T,
CVT

16 inch
wheel

1,448
mm

57.0 in

CVT

17 inch
wheel

1,448
mm

57.0 in

M/T,
CVT

18 inch
wheel

1,450
mm

57.1 in

Technical and consumer information

10-9

Metric
Mea-
sure

US
Measure

Front track

S, SV

16 inch
wheel

1,588
mm

62.5 in

17 inch
wheel

1,572
mm

61.9 in

18 inch
wheel

1,582
mm

62.3 in

Rear track

S, SV

16 inch
wheel

1,585
mm

62.4 in

17 inch
wheel

1,570
mm

61.8 in

18 inch
wheel

1,580
mm

62.2 in

Wheelbase

2,707
mm

106.6 in

Metric
Mea-
sure

US
Measure

Gross
vehicle
weight
rating

Refer to “F.M.V.S.S./
C.M.V.S.S. certification
label” on the center
pillar between the
driver's side front and
rear doors.

Gross axle
weight
rating

Front

Rear

10-10

Technical and consumer information

When planning to drive your NISSAN ve-
hicle in another country,

you should first

find out if the fuel available is suitable for
your vehicle's engine.

Using fuel with an octane rating that is too
low may cause engine damage. All gaso-
line vehicles must be operated with un-
leaded gasoline. Therefore, avoid taking
your vehicle to areas where appropriate
fuel is not available.

When transferring the registration of
your vehicle to another country, state,
province or district,

it may be necessary

to modify the vehicle to meet local laws
and regulations.

The laws and regulations for motor vehicle
emission control and safety standards
vary according to the country, state, prov-
ince or district; therefore, vehicle specifica-
tions may differ.

When any vehicle is to be taken into an-
other country, state, province or district
and registered, its modifications, trans-
portation and registration are the re-
sponsibility of the user. NISSAN is not re-
sponsible for any inconvenience that
may result.

VEHICLE IDENTIFICATION NUMBER
(VIN) PLATE

The Vehicle Identification Number (VIN)
plate is attached as shown. This number is
the identification for your vehicle and is
used in the vehicle registration.

VEHICLE IDENTIFICATION NUMBER
(chassis number)

The vehicle identification number is lo-
cated as shown.

LTI2050

LTI2483

WHEN TRAVELING OR REGISTERING
IN ANOTHER COUNTRY

VEHICLE IDENTIFICATION

Technical and consumer information

10-11

ENGINE SERIAL NUMBER

The number is stamped on the engine as
shown.

F.M.V.S.S./C.M.V.S.S. CERTIFICATION
LABEL

The

Federal/Canadian

Motor

Vehicle

Safety Standard (F.M.V.S.S./C.M.V.S.S.) certifi-
cation label is affixed as shown. This label
contains valuable vehicle information, such
as: (GVWR), (GAWR), month and year of
manufacture, (VIN), etc. Review it carefully.

EMISSION CONTROL
INFORMATION LABEL

The emission control information label is
attached to the underside of the hood as
shown.

STI0466

STI0349

WTI0178

10-12

Technical and consumer information

Symbol Name

Reference

Graphic

Caution

ISO 7000 0434

Air Conditioning System
(MAC)

ISO 2575 D01

MAC System Lubricant Type
(PAG–POE)

Requires Registered Technician to
Service MAC System

Flammable Refrigerant

Air Conditioner Specification Label Symbols

To mount the front license plate, attach the
license plate bracket to the grille assembly
at the location marks (small dimples) using
the two provided screws

NOTE:

Maximum screw length to attach license
plate to bracket must be 0.63 in (16 mm).

LTI2714

INSTALLING FRONT LICENSE PLATE

10-14

Technical and consumer information

WARNING

•

It is extremely dangerous to ride
in a cargo area inside a vehicle.
In a collision, people riding in
these areas are more likely to be
seriously injured or killed.

•

Do not allow people to ride in
any area of your vehicle that is
not equipped with seats and
seat belts.

•

Be sure everyone in your ve-
hicle is in a seat and using a
seat belt properly.

TERMS

It is important to familiarize yourself
with the following terms before
loading your vehicle:

• Curb Weight (actual weight of your

vehicle) - vehicle weight including:
standard parts, fluids, emergency
tools and spare tire assembly. This
weight

does not

include passen-

gers and cargo.

• GVW (Gross Vehicle Weight) - curb

weight plus the combined weight
of passengers and cargo.

• GVWR (Gross Vehicle Weight Rat-

ing) - maximum total combined
weight of the unloaded vehicle,
passengers, cargo, hitch, trailer
tongue load and any other op-
tional equipment. This information
is

located

the

F.M.V.S.S./

C.M.V.S.S. certification label.

• GAWR (Gross Axle Weight Rating) -

maximum

weight

(load)

limit

specified for the front or rear axle.
This information is located on the
F.M.V.S.S./C.M.V.S.S.

certification

label.

• GCWR (Gross Combined Weight

Rating)

The

maximum

total

weight rating of the vehicle, pas-
sengers, cargo, and trailer.

• Vehicle Capacity Weight, Load limit,

Total load capacity - maximum to-
tal weight limit specified of the load
(passengers and cargo) for the ve-
hicle. This is the maximum com-
bined weight of occupants and
cargo that can be loaded into the
vehicle. If the vehicle is used to tow
a trailer, the trailer tongue weight
must be included as part of the
cargo load. This information is lo-
cated on the Tire and Loading In-
formation label.

• Cargo

capacity

permissible

weight of cargo, the subtracted
weight of occupants from the load
limit.

VEHICLE LOADING INFORMATION

Technical and consumer information

10-15

VEHICLE LOAD CAPACITY

Before driving a loaded vehicle, con-
firm that you do not exceed the
Gross Vehicle Weight Rating (GVWR)
or the Gross Axle Weight Rating
(GAWR) for your vehicle. Both the
GVWR and GAWR are located on the
F.M.V.S.S./C.M.V.S.S. certification label.
For additional information, see “Mea-
surement of weights” (P. 10-18).

Do not exceed the load limit of your
vehicle shown as “The combined
weight of occupants and cargo” on
the Tire and Loading Information la-
bel. Do not exceed the number of
occupants shown as “Seating Ca-
pacity” on the Tire and Loading Infor-
mation label.

To get “the combined weight of oc-
cupants and cargo”, add the weight
of all occupants, then add the total
cargo weight. Examples are shown
in the following illustration.

Steps For Determining Correct
Load Limit

LTI2335

Example

10-16

Technical and consumer information

1. Locate the statement “The com-

bined weight of occupants and
cargo should never exceed XXX kg
or XXX lbs.” on your vehicle’s
placard.

2. Determine the combined weight

of the driver and passengers that
will be riding in your vehicle.

3. Subtract the combined weight of

the driver and passengers from
XXX kg or XXX lbs.

4. The resulting figure equals the

available amount of cargo and
luggage load capacity. For ex-
ample, if the “XXX” amount equals
1400 lbs. and there will be five 150
lb. passengers in your vehicle, the
amount of available cargo and
luggage load capacity is 650 lbs.
(1400-750 (5 X 150) = 650 lbs.)

5. Determine the combined weight

luggage

and

cargo

being

loaded on the vehicle. That weight
may not safely exceed the avail-
able cargo and luggage load ca-
pacity calculated in step 4.

6. If your vehicle will be towing a

trailer, load from your trailer will be
transferred to your vehicle. Con-
sult this manual to determine
how this reduces the available
cargo and luggage load capacity
of your vehicle.

Towing a trailer with a vehicle that is
not intended for towing may result in
an accident involving injury or death.

WARNING

Do not tow a trailer with your ve-
hicle. Towing a trailer may result
in an accident involving injury or
death.

Before driving a loaded vehicle, con-
firm that you do not exceed the
(GVWR) or the (GAWR) for your ve-
hicle. For additional information, see
“Measurement of weights” (P. 10-18).

Also check tires for proper inflation
pressures. For additional informa-
tion, see “Tire and Loading Informa-
tion label” (P. 8-31).

LOADING TIPS

• The GVW must not exceed GVWR or

GAWR as specified on the F.M.V.S.S./
C.M.V.S.S. certification label.

• Do not load the front and rear axle

to the GAWR. Doing so will exceed
the GVWR.

Technical and consumer information

10-17

WARNING

•

Properly secure all cargo with
ropes or straps to help prevent
it from sliding or shifting. Do
not place cargo higher than the
seatbacks. In a sudden stop or
collision,

unsecured

cargo

could cause personal injury.

•

Do not load your vehicle any
heavier than the GVWR or the
maximum

front

and

rear

GAWRs. If you do, parts of your
vehicle can break, tire damage
could occur, or it can change
the way your vehicle handles.
This could result in loss of con-
trol and cause personal injury.

•

Overloading

not

only

can

shorten the life of your vehicle
and the tire, but can also cause
unsafe vehicle handling and
longer braking distances. This
may cause a premature tire
failure which could result in a
serious accident and personal
injury. Failures caused by over-
loading are not covered by the
vehicle’s warranty.

MEASUREMENT OF WEIGHTS

Secure

loose

items

prevent

weight shifts that could affect the
balance of your vehicle. When the ve-
hicle is loaded, drive to a scale and
weigh the front and the rear wheels
separately to determine axle loads.
Individual axle loads should not ex-
ceed either of the Gross Axle Weight
Ratings (GAWR). The total of the axle
loads should not exceed the Gross
Vehicle Weight Rating (GVWR). These
ratings are given on the vehicle cer-
tification label. If weight ratings are
exceeded, move or remove items to
bring all weights below the ratings.

10-18

Technical and consumer information

Do not tow a trailer with your vehicle.

FLAT TOWING

Towing your vehicle with all four wheels on
the ground is sometimes called flat towing.
This method is sometimes used when
towing a vehicle behind a recreational ve-
hicle, such as a motor home.

CAUTION

•

Failure to follow these guidelines can
result in severe transmission damage.

•

Whenever flat towing your vehicle,
always tow forward, never backward.

•

Never tow your front wheel drive ve-
hicle with the front tires on the
ground. Doing so may cause serious
and

expensive

damage

the

powertrain.

•

DO NOT tow any continuously vari-
able transmission vehicle with all
four wheels on the ground (flat tow-
ing). Doing so WILL DAMAGE internal
transmission parts due to lack of
transmission lubrication.

•

For emergency towing procedures see
“Towing recommended by NISSAN”
(P. 6-12).

Manual Transmission (if so
equipped)

• Always tow with the manual transmis-

sion in N (Neutral).

• After towing 500 miles (805 km), start and

idle the engine with the transmission in N
(Neutral) for two minutes. Failure to idle
the engine after every 500 miles (805 km)
of towing may cause damage to internal
transmission parts.

Continuously Variable
Transmission (if so equipped)

To tow a vehicle equipped with a continu-
ously variable transmission, an appropriate
vehicle dolly

MUST

be placed under the

towed vehicle's drive wheels.

Always

the dolly manufacturer's recommenda-
tions when using their product.

DOT (Department of Transportation) Qual-
ity Grades: All passenger car tires must
conform to federal safety requirements in
addition to these grades.

Quality grades can be found where appli-
cable on the tire sidewall between tread
shoulder and maximum section width. For
example:

Treadwear 200 Traction AA Temperature A

Treadwear

The treadwear grade is a comparative rat-
ing based on the wear rate of the tire when
tested under controlled conditions on a
specified government test course. For ex-
ample, a tire graded 150 would wear one
and one-half (1 1/2) times as well on the
government course as a tire graded 100.
The relative performance of tires depends
upon the actual conditions of their use,
however, and may depart significantly from
the norm due to variations in driving habits,
service practices and differences in road
characteristics and climate.

TOWING A TRAILER

UNIFORM TIRE QUALITY GRADING

Technical and consumer information

10-19

Traction AA, A, B and C

The traction grades, from highest to low-
est, are AA, A, B, and C. Those grades repre-
sent the tire's ability to stop on wet pave-
ment

measured

under

controlled

conditions on specified government test
surfaces of asphalt and concrete. A tire
marked

may

have

poor

traction

performance.

WARNING

The traction grade assigned to this tire
is based on straight-ahead braking
traction tests, and does not include ac-
celeration, cornering, hydroplaning, or
peak traction characteristics.

Temperature A, B and C

The temperature grades are A (the high-
est), B, and C, representing the tire’s resis-
tance to the generation of heat, and its
ability to dissipate heat when tested under
controlled conditions on a specified indoor
laboratory test wheel. Sustained high tem-
perature can cause the material of the tire
to degenerate and reduce tire life, and ex-
cessive temperature can lead to sudden
tire failure. The grade C corresponds to a
level of performance which all passenger

car tires must meet under the Federal Mo-
tor Safety Standard No. 109. Grades B and A
represent higher levels of performance on
the laboratory test wheel than the mini-
mum required by law.

WARNING

The temperature grade for this tire is
established for a tire that is properly
inflated and not overloaded. Excessive
speed, under-inflation, or excessive
loading, either separately or in combi-
nation, can cause heat build-up and
possible tire failure.

For USA

If you believe that your vehicle has a
defect which could cause a crash or
could cause injury or death, you
should immediately inform the Na-
tional Highway Traffic Safety Admin-
istration (NHTSA) in addition to noti-
fying NISSAN.

If NHTSA receives similar complaints,
it may open an investigation, and if it
finds that a safety defect exists in a
group of vehicles, it may order a re-
call and remedy campaign. However,
NHTSA cannot become involved in
individual problems between you,
your dealer, or NISSAN.

To contact NHTSA, you may call the
Vehicle Safety Hotline toll-free at
1-888-327-4236 (TTY: 1-800-424-9153);
go to http://www.safercar.gov; or
write to: Administrator, NHTSA, 1200
New Jersey Avenue, SE Washington,
D.C. 20590. You can also obtain other

REPORTING SAFETY DEFECTS

10-20

Technical and consumer information

information

about

motor

vehicle

safety from http://www.safercar.gov.

You may notify NISSAN by contact-
ing our Consumer Affairs Depart-
ment, toll-free, at 1-800-NISSAN-1.

For Canada

If you believe that your vehicle has a
defect which could cause a crash or
could cause injury or death, you
should immediately inform Trans-
port Canada in addition to notifying
NISSAN.

If Transport Canada receives com-
plaints, it may open an investigation,
and if it finds that a safety defect
exists in a group of vehicles, it may
request that NISSAN conduct a re-
call campaign. However, Transport
Canada cannot become involved in
individual problems between you,
your dealer, or NISSAN.

You may contact Transport Cana-
da's Defect Investigations and Re-
calls Division toll free at 1-800-333-
0510. You may also report safety
defects online at:
http://www.tc.gc.ca/eng/
motorvehiclesafety/menu.htm
(English speakers) or
http://www.tc.gc.ca/fra/
securiteautomobile/menu.htm
(French speakers)

Or contact Transport Canada by
mail at:
Transport Canada Motor Vehicle
Safety Investigations Laboratory
80 Noel Street Gatineau, QC J8Z0A1

Additional

information

concerning

motor vehicle safety may be obtained
from Transport Canada's Road Safety
Information Centre at 1-800-333-0371
or online at www.tc.gc.ca/roadsafety
(English speakers) or www.tc.gc.ca/
securiteroutiere (French speakers).

To notify NISSAN of any safety con-
cerns please contact our Consumer
Information

Centre

toll

free

1-800-387-0122.

Technical and consumer information

10-21

Due to legal requirements in some states
and Canadian Provinces, your vehicle may
be required to be in what is called the
“ready

condition”

for

Inspection/

Maintenance (I/M) test of the emission
control system.

The vehicle is set to the “ready condition”
when it is driven through certain driving
patterns. Usually, the ready condition can
be obtained by ordinary usage of the
vehicle.

If a powertrain system component is re-
paired or the battery is disconnected, the
vehicle may be reset to a “not ready” condi-
tion. Before taking the I/M test, check the
vehicle's

inspection/maintenance

test

readiness condition. Place the ignition
switch in the ON position without starting
the engine. If the Malfunction Indicator
Light (MIL) comes on steady for 20 seconds
and then blinks for 10 seconds , the I/M test
condition is “not ready”. If the MIL does not
blink after 20 seconds, the I/M test condi-
tion is “ready”. It is recommended that you
visit a NISSAN dealer to set the “ready con-
dition” or to prepare the vehicle for testing.

Your NISSAN vehicle is covered by the fol-
lowing emission warranties:

For USA

1. Emission Defects Warranty

2. Emissions Performance Warranty

Details of this warranty may be found with
other vehicle warranties in your Warranty
Information Booklet which comes with
your NISSAN vehicle. If you did not receive a
Warranty Information Booklet, or it is lost,
you may obtain a replacement by writing
to:
• Nissan North America, Inc.

Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003

For Canada

Emission Control System Warranty

5290 Orbitor Drive
Mississauga, Ontario, L4W 4Z5

This vehicle is equipped with an Event Data
Recorder (EDR). The main purpose of an
EDR is to record, in certain crash or near
crash-like situations, such as an air bag
deployment or hitting a road obstacle, data
that will assist in understanding how a ve-
hicle's systems performed. The EDR is de-
signed to record data related to vehicle dy-
namics and safety systems for a short
period of time, typically 30 seconds or less.
The EDR in this vehicle is designed to re-
cord such data as:
• How various systems in your vehicle were

operating;

• Whether or not the driver and passenger

safety belts were buckled/fastened;

• How far (if at all) the driver was depress-

ing the accelerator and/or brake pedal;
and,

• How fast the vehicle was traveling.
• Sounds are not recorded.

These data can help provide a better un-
derstanding of the circumstances in which
crashes and injuries occur. NOTE: EDR data
are recorded by your vehicle only if a non-
trivial crash situation occurs; no data are
recorded by the EDR under normal driving
conditions and no personal data (e.g.,
name, gender, age, and crash location) are
recorded. However, other parties, such as

READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST

EMISSION CONTROL SYSTEM
WARRANTY

EVENT DATA RECORDERS (EDR)

10-22

Technical and consumer information

law enforcement, could combine the EDR
data with the type of personally identifying
data routinely acquired during a crash
investigation.

To read data recorded by an EDR, special
equipment is required, and access to the
vehicle or the EDR is needed. In addition to
the vehicle manufacturer and NISSAN
dealer, other parties, such as law enforce-
ment, that have the special equipment, can
read the information if they have access to
the vehicle or the EDR.

EDR data will only be accessed with the
consent of the vehicle owner or lessee or
as otherwise required or permitted by law.

Genuine NISSAN Service Manuals for this
model year and prior can be purchased. A
Genuine NISSAN Service Manual is the best
source of service and repair information for
your vehicle. This manual is the same one
used by the factory-trained technicians
working at NISSAN dealerships. Genuine
NISSAN Owner’s Manuals can also be
purchased.

For USA

For

current

pricing

and

availability

Genuine

NISSAN Service Manuals,

contact:

www.nissan-techinfo.com

For

current

pricing

and

availability

Genuine

NISSAN Owner's Manuals,

contact:

1-800-247-5321

For Canada

To purchase a copy of a Genuine NISSAN
Service Manual or Owner’s Manual, for this
model year and prior, please visit the near-
est NISSAN dealer. For the phone number
and location of a NISSAN dealer in your
area, call the NISSAN Information Center at
1-800-387-0122 and a bilingual NISSAN rep-
resentative will assist you.

OWNER'S MANUAL/SERVICE
MANUAL ORDER INFORMATION

Technical and consumer information

10-23

Nissan Sentra (2024 year). Manual in english - page 16