Nissan Sentra (2024 year). Manual in english

To set cruising speed, accelerate your ve-
hicle to the desired speed, push the SET-

switch and release it. (The color of the
cruise indicator changes to green and set
vehicle speed indicator comes on.) Take
your foot off the accelerator pedal. Your
vehicle will maintain the set speed.
• To pass another vehicle, depress the ac-

celerator pedal. When you release the
pedal, the vehicle will return to the previ-
ously set speed.

• The vehicle may not maintain the set

speed when going up or down steep hills.
If this happens, manually maintain ve-
hicle speed.

To cancel the preset speed, use any of the
following methods:

1. Push the CANCEL switch. The vehicle

speed indicator will turn off.

2. Tap the brake pedal. The vehicle speed

indicator will turn off.

3. Turn the ICC switch off. Both the cruise

indicator and vehicle speed indicator will
turn off.

To reset at a faster cruising speed, use one
of the following three methods:

1. Depress the accelerator pedal. When the

vehicle attains the desired speed, push
and release the SET- switch.

2. Push and hold the RES+ switch. When

the vehicle attains the desired speed,
release the switch.

3. Push, then quickly release the RES+

switch. Each time you do this, the set
speed will increase by about 1 mph (1
km/h).

To reset at a slower cruising speed, use one
of the following three methods:

1. Lightly tap the brake pedal. When the

vehicle attains the desired speed, push
the SET- switch and release it.

2. Push and hold the SET- switch. Release

the switch when the vehicle slows down
to the desired speed.

3. Push, then quickly release the SET-

switch. Each time you do this, the set
speed will decrease by about 1 mph (1
km/h).

To resume the preset speed, push and re-
lease the RES+ switch. The vehicle will re-
sume the last set cruising speed when the
vehicle speed is over 25 mph (40 km/h).

LSD3557

5-82

Starting and driving

Action to take

If the color of the cruise indicator changes
to orange, stop the vehicle in a safe place
and place the shift lever in the P (Park) po-
sition. Turn the engine off, restart the en-
gine, resume driving, and then perform the
setting again.

If it is not possible to set or the indicator
stays on, it may indicate that the system
is malfunctioning. Although the vehicle
is still drivable under normal conditions,
have the vehicle checked. It is recom-
mended that you visit a NISSAN dealer
for this service.

WARNING

Failure to follow the warnings and in-
structions for proper use of the RAB
system could result in serious injury or
death.

•

The RAB system is a supplemental
aid to the driver. It is not a replace-
ment for proper driving procedures.
Always use the side and rear mirrors
and turn and look in the direction you
will move before and while backing
up. Never rely solely on the RAB sys-
tem. It is the driver’s responsibility to
stay alert, drive safely, and be in con-
trol of the vehicle at all times.

•

There is a limitation to the RAB sys-
tem capability. The RAB system is not
effective in all situations.

•

Inclement

weather

ultrasonic

sources such as an automatic car
wash,

truck’s

compressed-air

brakes or a pneumatic drill may af-
fect the function of the system; this
may include reduced performance or
a false activation.

The RAB system can assist the driver when
the vehicle is backing up and approaching
objects directly behind the vehicle.

The RAB system detects obstacles behind
the vehicle using the parking sensors

located on the rear bumper.

NOTE:

You can temporarily cancel the sonar
function in the vehicle, but the RAB sys-
tem will continue to operate. For addi-
tional information, please see “Rear So-
nar System (RSS)” (P. 5-133).

LSD3754

REAR AUTOMATIC BRAKING (RAB)

5-84

Starting and driving

RAB SYSTEM OPERATION

䊊

RAB system warning light

䊊

RAB system warning indicator

䊊

Center display

䊊

Steering-wheel-mounted controls (left
side)

When the shift lever is in the R (Reverse)
position and the vehicle speed is less than
approximately 9 mph (15 km/h), the RAB
system operates.

If a risk of a collision with an obstacle is
detected when your vehicle is backing up,
the RAB system warning indicator will flash
in the vehicle information display, a red
frame will appear in the center display (for
vehicles with the Intelligent Around View®
Monitor system), and the system will chime
three times. The system will then auto-
matically apply the brakes. After the auto-
matic brake application, the driver must
depress the brake pedal to maintain brake
pressure.

LSD5956

For vehicles with the 7 inch meter display

Starting and driving

5-85

RAB SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the RAB system. Failure to follow the
warnings and instructions for proper
use of the RAB system could result in
serious injury or death.

•

When the vehicle approaches an ob-
stacle while the accelerator or brake
pedal is depressed, the function may
not operate or the start of operation
may be delayed. The RAB system
may not operate or may not perform
sufficiently due to vehicle conditions,
driving conditions, the traffic envi-
ronment, the weather, road surface
conditions, etc. Do not wait for the
system to operate. Operate the brake
pedal

yourself

soon

necessary.

•

If it is necessary to override RAB op-
eration, strongly press the accelera-
tor pedal.

LSD3788

For vehicles with the 4.2 inch meter display

5-88

Starting and driving

•

Always check your surroundings and
turn to check what is behind you be-
fore and while backing up. The RAB
system detects stationary objects
behind the vehicle. The RAB system
does not detect the following ob-
jects:

–

Moving objects

–

Low objects

–

Narrow objects

–

Wedge-shaped objects

–

Objects close to the bumper (less

than approximately 1 ft [30 cm])

–

Objects that suddenly appear

–

Thin objects such as rope, wire,

chain, etc.

•

The RAB system may not operate for
the following obstacles:

–

Obstacles located high off the

ground

–

Obstacles in a position offset from

your vehicle

–

Obstacles, such as spongy materi-

als or snow, that have soft outer
surfaces and can easily absorb a
sound wave

•

The RAB system may not operate in
the following conditions:

–

There is rain, snow, ice, dirt, etc.,

attached to the sonar sensors.

–

A loud sound is heard in the area

around the vehicle.

–

The surface of the obstacle is di-

agonal to the rear of the vehicle.

•

The RAB system may unintentionally
operate in the following conditions:

–

There is overgrown grass in the

area around the vehicle.

–

There is a structure (e.g., a wall, toll

gate equipment, a narrow tunnel,
a parking lot gate) near the side of
the vehicle.

–

There are bumps, protrusions, or

manhole covers on the road surface.

–

The

vehicle

drives

through

draped flag or a curtain.

–

There is an accumulation of snow

or ice behind the vehicle.

–

An ultrasonic wave source, such as

another vehicle’s sonar, is near
the vehicle.

•

Once the automatic brake control oper-
ates, it does not operate again if the
vehicle approaches the same obstacle.

•

The automatic brake control can only
operate for a short period of time.
Therefore, the driver must depress
the brake pedal.

•

In the following situations, the RAB
system may not operate properly or
may not function sufficiently:

–

The

vehicle

driven

bad

weather (rain, fog, snow, etc.).

–

The vehicle is driven on a steep

hill.

–

The vehicle’s posture is changed

(e.g., when driving over a bump).

–

The vehicle is driven on a slippery

road.

–

The vehicle is turned sharply by

turning the steering wheel fully.

–

Snow chains are used.

–

Wheels or tires other than NISSAN

recommended are used.

–

The brakes are cold at low ambi-

ent temperatures or immediately
after driving has started.

–

The braking force becomes poor

due to wet brakes after driving
through a puddle or washing the
vehicle.

Starting and driving

5-89

•

Turn the RAB system off in the follow-
ing conditions to prevent the occur-
rence of an unexpected accident
resulting from sudden system op-
eration:

–

The vehicle is towed.

–

The vehicle is carried on a flatbed

truck.

–

The vehicle is on the chassis

dynamometer.

–

The vehicle drives on an uneven

road surface.

–

Suspension

parts

other

than

those

designated

Genuine

NISSAN parts are used. (If the ve-
hicle height or the vehicle body in-
clination is changed, the system
may

not

detect

obstacle

correctly.)

–

If the vehicle is using an accessory

like a bike rack, or cargo carrier
that blocks the sensors.

•

Excessive noise (e.g., audio system
volume, an open vehicle window) will
interfere with the chime sound, and it
may not be heard.

SYSTEM MALFUNCTION

If the RAB system malfunctions, it will be
turned off automatically, the RAB system
warning light will illuminate, and the “Not
Available System Malfunction” warning
message will appear in the vehicle infor-
mation display.

Action to take

If the warning light illuminates, park the ve-
hicle in a safe location, turn the engine off,
and restart the engine. If the warning light
continues to illuminate, have the RAB sys-
tem checked. It is recommended that you
visit a NISSAN dealer for this service.

NOTE:

If the RAB system cannot be operated
temporarily, the RAB system warning
light blinks.

SYSTEM MAINTENANCE

Observe the following items to ensure
proper operation of the system:
• Always keep the parking sensors

clean.

• If the parking sensors are dirty, wipe them

off with a soft cloth while being careful to
not damage them.

LSD3754

5-90

Starting and driving

• Do not subject the area around the park-

ing sensors

to strong impact. Also, do

not remove or disassemble the parking
sensors. If the parking sensors and pe-
ripheral areas are deformed in an acci-
dent, etc., have the sensors checked. It is
recommended that you visit a NISSAN
dealer for this service.

• Do not install any stickers (including

transparent stickers) or accessories on
the parking sensors

and their sur-

rounding areas. This may cause a mal-
function or improper operation.

WARNING

Failure to follow the warnings and in-
structions for proper use of the AEB
with

Pedestrian

Detection

system

could result in serious injury or death.

•

The AEB with Pedestrian Detection
system is a supplemental aid to the
driver. It is not a replacement for the
driver’s attention to traffic condi-
tions or responsibility to drive safely.
It cannot prevent accidents due to
carelessness or dangerous driving
techniques.

•

The AEB with Pedestrian Detection
system does not function in all driv-
ing,

traffic,

weather

and

road

conditions.

The AEB with Pedestrian Detection system
can assist the driver when there is a risk of
a forward collision with the vehicle ahead in
the traveling lane or with a pedestrian
ahead in the traveling lane.

The AEB with Pedestrian Detection system
uses a radar sensor located on the front of
the vehicle

to measure the distance to

the vehicle ahead in the same lane. For
pedestrians, the AEB with Pedestrian De-
tection system uses a camera installed be-
hind the windshield

in addition to the

radar sensor.

LSD3756

AUTOMATIC EMERGENCY BRAKING
(AEB) WITH PEDESTRIAN DETECTION

Starting and driving

5-91

If the driver does not take action, the AEB
with Pedestrian Detection system issues
the second visual (flashing) (red and white)
and audible warning. If the driver releases
the accelerator pedal, then the system ap-
plies partial braking. If the risk of a collision
becomes imminent, the AEB with Pedes-
trian Detection system applies harder
braking automatically.

While the AEB with Pedestrian Detection
system is operating, you may hear the
sound of brake operation. This is normal
and indicates that the AEB with Pedestrian
Detection system is operating properly.

NOTE:

The vehicle’s brake lights come on when
any braking is performed by the AEB
with Pedestrian Detection system.

Depending on vehicle speed and distance
to the vehicle or pedestrian ahead, as well
as driving and roadway conditions, the sys-
tem may help the driver avoid a forward
collision or may help mitigate the conse-
quences if a collision should be unavoid-
able. If the driver is handling the steering
wheel, accelerating or braking, the AEB with
Pedestrian Detection system will function
later or will not function.

LSD4533

For the vehicle with 4.2 inch meter display

Starting and driving

5-93

Perform the following steps to enable or
disable the AEB with Pedestrian Detection
system.

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the

button to select “Driver As-

sistance.” Then press the OK button.

2. Select “Emergency Brake” and press the

OK button.

3. Select “Front” and press the OK button to

turn the system on or off.

When the AEB with Pedestrian Detection
system is turned off, the AEB with Pedestrian
Detection system warning light illuminates.

NOTE:

•

The AEB with Pedestrian Detection sys-
tem will be automatically turned on
when the engine is restarted.

•

The I-FCW system is integrated into the
AEB with Pedestrian Detection system.
There is not a separate selection in the
vehicle information display for the I-FCW
system. When the AEB system is turned
off, the I-FCW system is also turned off.

•

When the VDC system is turned off, the
AEB with Pedestrian Detection system
will not be available except for the
I-FCW system.

LSD3788

For vehicles with the 4.2 inch meter display

Starting and driving

5-95

AEB WITH PEDESTRIAN
DETECTION SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the AEB with Pedestrian Detection
system. Failure to operate the vehicle in
accordance with these system limita-
tions could result in serious injury or
death.

•

The AEB with Pedestrian Detection
system cannot detect all vehicles or
pedestrians under all conditions.

•

The AEB with Pedestrian Detection
system does not detect the following:

–

Pedestrians that are small (for ex-
ample, children), in a sitting posi-
tion, operating toys/skateboards,
on scooters or in wheelchairs, or
not in an upright standing or
walking position.

–

Animals of any size.

–

Obstacles (for example, cargo or
debris) on the roadway or roadside.

–

Oncoming or crossing vehicles.

–

Vehicles where the tires are difficult
to see or the shape of the rear of the
vehicle is unclear or obstructed.

–

Parked vehicles.

•

The AEB with Pedestrian Detection
system has some performance limi-
tations.

–

If a stationary vehicle is in the ve-

hicle’s path, the system will not
function when the vehicle ap-
proaches the stationary vehicle at
speeds over approximately 50
mph (80 km/h).

–

Pedestrian

detection

will

not

function

when

the

vehicle

driven at speeds over approxi-
mately 37 mph (60 km/h) or below
approximately 6 mph (10km/h).

•

For pedestrians, the AEB with Pedes-
trian Detection system will not issue
the first warning.

•

The AEB with Pedestrian Detection
system may not function properly or
detect

vehicle

pedestrians

ahead in the following conditions:

–

In poor visibility conditions (such
as rain, snow, fog, dust storms,
sand storms, smoke, and road
spray from other vehicles).

–

If dirt, ice, snow, fog or other mate-
rial is covering the radar sensor
area or camera area of windshield.

–

If strong light (for example, sun-
light or high beams) enters the
front camera or a sudden change
in brightness occurs (for example,
entering a tunnel or driving in
lightning).

–

In dark or dimly lit conditions,
such as at night or in tunnels, in-
cluding cases where your vehi-
cle’s headlights are off or dim, or
the tail lights of the vehicle ahead
are off.

–

When the direction of the camera
is misaligned.

–

When driving on a steep downhill
slope, on roads with sharp curves,
and/or bumpy or dirt roads.

–

If there is interference by other ra-
dar sources.

–

When your vehicle’s position or
movement is changed quickly or
significantly (for example, lane
change, turning vehicle, abrupt
steering, sudden acceleration or
deceleration).

5-96

Starting and driving

–

When your vehicle or the vehicle
or

pedestrian

ahead

moves

quickly or significantly such that
the system cannot detect and re-
act in time (for example, pedes-
trian moving quickly toward the
vehicle at close range, vehicle cut-
ting in, changing lanes, making a
turn, steering abruptly, sudden
acceleration or deceleration).

–

When the vehicle or pedestrian is
offset from the vehicle’s forward
path.

–

If the speed difference between
the two vehicles is small.

–

The pedestrian’s profile is par-
tially obscured or unidentifiable;
for example, due to transporting
luggage, pushing a stroller, wear-
ing bulky or very loose-fitting
clothing or accessories, or being
in a unique posture (such as rais-
ing hands).

–

There is poor contrast of a person
to the background, such as having
clothing color or pattern which is
similar to the background.

–

For approximately 15 seconds af-
ter starting the engine.

–

If the vehicle ahead has a unique
or unusual shape, extremely low
or high clearance heights, or un-
usual cargo loading or is narrow
(for example, a motorcycle).

–

When the vehicle or pedestrian is
located near a traffic sign, a reflec-
tive area (for example, water on
road), or is in a shadow.

–

When multiple pedestrians are
grouped together.

–

When the view of the pedestrian is
obscured by a vehicle or other
object.

•

The system performance may be de-
graded in the following conditions:

–

The vehicle is driven on a slippery
road.

–

The vehicle is driven on a slope.

–

Excessively

heavy

baggage

loaded in the rear seat or the
cargo area of your vehicle.

•

The system is designed to automati-
cally check the sensor’s (radar and
camera) functionality, within certain
limitations. The system may not de-
tect some forms of obstruction of the
sensor area such as ice, snow or
stickers, for example. In these cases,
the system may not be able to warn

the driver properly. Be sure that you
check, clean and clear sensor areas
regularly.

•

In some road and traffic conditions,
the AEB with Pedestrian Detection
system may unexpectedly apply par-
tial braking. When acceleration is
necessary, depress the accelerator
pedal to override the system.

•

The AEB with Pedestrian Detection
system may operate when a pattern,
object, shadow or lights are detected
that are similar to the outline of ve-
hicles or pedestrians, or if they are
the same size and position as a ve-
hicle or motorcycle’s tail lights.

•

The system may keep operating
when the vehicle ahead is turning
right or left.

•

The system may operate when your
vehicle is approaching and passing a
vehicle ahead.

•

Depending

the

road

shape

(curved road, entrance and exit of the
curve, winding road, lane regulation,
under construction, etc.), the system
may operate temporarily for the on-
coming vehicle in front of your
vehicle.

Starting and driving

5-97

WARNING

•

The AEB with Pedestrian Detection
system may react to:

–

objects on the roadside (traffic
sign, guardrail, pedestrian, motor-
cycle, vehicle, etc.)

–

pedestrians when driving on the
narrow alleys, etc.

–

pedestrians who temporarily pro-
trude into or approaching the
driving lane to avoid the obstacles
on the road shoulder

–

objects above road (low bridge,
traffic sign, etc.)

–

objects on the road surface (rail-
road track, grate, steel plate, etc.)

–

objects in the e parking garage
(beam, pillar, etc.)

–

pedestrians or motorcycles ap-
proaching the travelling lane

–

vehicles,

pedestrians,

motor-

cycles or objects in adjacent lanes
or close to the vehicle

–

oncoming pedestrians

–

objects on the road (such as trees)

•

Braking distances increase on slip-
pery surfaces.

•

Excessive noise will interfere with the
warning chime sound, and the chime
may not be heard.

LSD4248

5-98

Starting and driving

SYSTEM TEMPORARILY
UNAVAILABLE

Condition A:

In the following conditions, the AEB with
Pedestrian Detection system warning light
blinks and the system will be turned off
automatically:
• The radar sensor picks up interference

from another radar source.

• The camera area of the windshield is

misted or frozen.

• Strong light is shining from the front.
• The cabin temperature is over approxi-

mately 104°F (40°C) in direct sunlight.

• The camera area of the windshield glass

is continuously covered with dirt, etc.

Action to take

When the above conditions no longer exist,
the AEB with Pedestrian Detection system
will resume automatically.

NOTE:

When the inside of the windshield on the
camera area is misted or frozen, it will
take a period of time to remove it after
the A/C turns on. If dirt appears on this
area, it is recommended that you visit a
NISSAN dealer.

LSD3795

For vehicles with the 7 inch meter display

Starting and driving

5-99

Condition B:

When there is inclement weather (rain, fog,
snow, etc.) blocking the front radar sensor,
the AEB with Pedestrian Detection system
will automatically be canceled, the chime
will sound, the “Forward Driving Aids Tem-
porarily Disabled Front Sensor Blocked: See
Owner’s Manual” or “Driving Aids Temporar-
ily Disabled Front Sensor Blocked: See
Manual” warning message will appear in
the vehicle information display and the AEB
with Pedestrian Detection system warning
light will blink.

Action to take:

When the conditions listed above are no
longer present, the warning message will
no longer be available in the vehicle infor-
mation display. If the “Forward Driving Aids
Temporarily

Disabled

Front

Sensor

Blocked: See Owner’s Manual” or “Driving
Aids Temporarily Disabled Front Sensor
Blocked: See Manual” warning message
continues to be displayed, have the system
checked. It is recommended that you visit a
NISSAN dealer for this service.

LSD3796

For vehicles with the 4.2 inch meter display

5-100

Starting and driving

Condition C:

When the radar sensor of the front bumper
is covered with mud, dirt, snow ice, etc., or is
obstructed, the AEB with Pedestrian Detec-
tion system will automatically be canceled.
The chime will sound, the “Forward Driving
Aids Temporarily Disabled Front Sensor
Blocked: See Owner’s Manual” or “Driving
Aids Temporarily Disabled Front Sensor
Blocked: See Manual” warning message will
appear in the vehicle information display
and the AEB with Pedestrian Detection sys-
tem warning light will blink.

Action to take:

If the warning message appears, stop the
vehicle in a safe place, place the shift lever
in the P (Park) position, and turn the engine
off. When the radar signal is temporarily
interrupted, clean the sensor area of the
front bumper and restart the engine. If the
“Forward Driving Aids Temporarily Disabled
Front Sensor Blocked: See Owner’s Manual”
or “Driving Aids Temporarily Disabled Front
Sensor Blocked: See Manual” warning mes-
sage continues to be displayed, have the
system checked. It is recommended that
you visit a NISSAN dealer for this service.

Condition D:

When driving on roads with limited road
structures or buildings (for example, long
bridges, deserts, snowfields, driving next to
long walls), the system may illuminate the
system warning light, display the “Forward
Driving Aids Temporarily Disabled Front
Sensor Blocked: See Owner’s Manual” or
“Driving Aids Temporarily Disabled Front
Sensor Blocked: See Manual” message and
the AEB with Pedestrian Detection system
warning light will blink.

Action to take:

When the above driving conditions no lon-
ger exist, turn the system back on.

Condition E:

When the Vehicle Dynamic Control (VDC)
system is OFF, the AEB brake will not oper-
ate. In this case, only visible and audible
warnings operate. The AEB with Pedestrian
Detection system warning light (orange)
will illuminate.

Action to take:

When the VDC system is ON, the AEB with
Pedestrian Detection system will resume
automatically.

NOTE:
If the AEB with Pedestrian Detection
system stops working, the I-FCW sys-
tem will also stop working.

Starting and driving

5-101

SYSTEM MALFUNCTION

If the AEB with Pedestrian Detection sys-
tem malfunctions, it will be turned off auto-
matically, a chime will sound, the AEB with
Pedestrian Detection system warning light
(orange) will illuminate and the warning
message [Malfunction] will appear in the
vehicle information display.

Action to take

If the warning light (orange) comes on, stop
the vehicle in a safe location, turn the en-
gine off and restart the engine. If the
warning light continues to illuminate, have
the AEB with Pedestrian Detection system
checked. It is recommended that you visit a
NISSAN dealer for this service.

SYSTEM MAINTENANCE

The radar sensor is located on the front of
the vehicle

. The camera is located on

the upper side of the windshield

To keep the AEB with Pedestrian Detection
system operating properly, be sure to ob-
serve the following:
• Always keep the sensor areas of the front

bumper/emblem and windshield clean.

• Do not strike or damage the areas around

the sensors (e.g., bumper, windshield).

LSD3890

LSD3756

5-102

Starting and driving

• Do not cover or attach stickers, or install

any accessory near the sensors. This
could block sensor signals and/or cause
failure or malfunction.

• Do not attach metallic objects near the

radar sensor (brush guard, etc.). This
could cause failure or malfunction.

• Do not place reflective materials, such as

white paper or a mirror, on the instru-
ment panel. The reflection of sunlight
may adversely affect the camera unit's
detection capability.

• Do not alter, remove or paint the front

bumper. Before customizing or restoring
the front bumper, it is recommended that
you visit a NISSAN dealer.

Radio frequency statement

For USA

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions:

This device may not cause harmful in-
terference, and

This device must accept any interfer-
ence received, including interference
that may cause undesired operation.

FCC Warning

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

For Canada

This device complies with Part 15 of the
FCC Rules and with Industry Canada
licence-exempt RSS standard(s). Opera-
tion is subject to the following two
conditions:

This device may not cause interfer-
ence, and

This device must accept any interfer-
ence received, including interference
that may cause undesired operation
of the device.

Le présent appareil est conforme aux
CNR d'Industrie Canada applicables aux
appareils radio exempts de licence.
L'exploitation est autorisée aux deux
conditions suivantes:

L'appareil ne doit pas produire de
brouillage, et

L'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi,
même si le brouillage est susceptible
d'en compromettre le fonctionnement.

Radio

frequency

radiation

exposure

information:

This equipment complies with FCC and IC
radiation exposure limits set forth for an
uncontrolled environment.

This equipment should be installed and
operated with minimum distance of 30
cm between the radiator and your body.

This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.

Starting and driving

5-103

Cet équipement est conforme aux lim-
ites d'exposition aux rayonnements IC
établies pour un environnement non
contrôlé.

Cet équipement doit être installé et
utilisé avec un minimum de 30 cm de
distance entre la source de rayonnement
et votre corps.

FCC Notice

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

WARNING

Failure to follow the warnings and in-
structions for proper use of the I-FCW
system could result in serious injury or
death.

•

The I-FCW system can help warn the
driver before a collision occurs but
will not avoid a collision. It is the driv-
er’s responsibility to stay alert, drive
safely and be in control of the vehicle
at all times.

The I-FCW system can help alert the driver
when there is a sudden braking of a second
vehicle traveling in front of the vehicle
ahead in the same lane.

The I-FCW system uses a radar sensor

located on the front of the vehicle to mea-
sure the distance to the vehicle ahead in
the same lane.

LSD3826

INTELLIGENT FORWARD COLLISION
WARNING (I-FCW)

5-104

Starting and driving

TURNING THE I-FCW SYSTEM
ON/OFF

Perform the following steps to turn the
I-FCW system ON or OFF.

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the

button to select “Driver As-

sistance.” Then press the OK button.

2. Select “Emergency Brake” and press the

OK button.

3. Select “Front” and press the OK button to

turn the system on or off.

When the I-FCW system is turned off, the
AEB with Pedestrian Detection system
warning light illuminates.

NOTE:
• The I-FCW system will be automatically

turned

when

the

engine

restarted.

• The I-FCW system is integrated into the

AEB with Pedestrian Detection system.
There is not a separate selection in the
vehicle information display for the
I-FCW system. When the AEB with Pe-
destrian Detection system is turned
off, the I-FCW system is also turned off.

LSD3979

For vehicles with the 7 inch meter display

5-108

Starting and driving

WARNING

Listed below are the system limitations
for the I-FCW system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

•

The I-FCW system cannot detect all
vehicles under all conditions.

•

The radar sensor does not detect the
following objects:

–

Pedestrians, animals or obstacles
in the roadway

–

Oncoming vehicles

–

Crossing vehicles

•

(Illustration A) The I-FCW system
does not function when a vehicle
ahead is a narrow vehicle, such as a
motorcycle.

•

The radar sensor may not detect a
vehicle

ahead

the

following

conditions:

–

Snow or heavy rain

–

Dirt, ice, snow or other material
covering the radar sensor.

–

Interference

other

radar

sources.

–

Snow or road spray from traveling
vehicles.

–

Driving in a tunnel

–

(Illustration B) When the vehicle
ahead is being towed.

–

(Illustration C) When the distance
to the vehicle ahead is too close,
the beam of the radar sensor is
obstructed.

LSD2265

Illustration B

5-110

Starting and driving

Nissan Sentra (2024 year). Manual in english - page 12