Nissan Sentra (2024 year). Manual in english

Steps

1. Adjust the seat as outlined in “Seats”

(P. 1-2). Sit upright, leaning against the
seatback, and centered on the seat
cushion with your feet comfortably ex-
tended to the floor.

2. Make sure there are no objects on your

lap.

3. Fasten the seat belt as outlined in “Seat

belts” (P. 1-11). Front passenger seat belt
buckle status is monitored by the occu-
pant classification system, and is used
as an input to determine occupancy
status. So, it is highly recommended that
the front passenger fasten their seat
belt.

4. Remain in this position for 30 seconds

allowing the system to classify the front
passenger before the vehicle is put into
motion.

5. Ensure proper classification by checking

the front passenger air bag status light.

NOTE:

This vehicle’s occupant classification
sensor system generally keeps the clas-
sification locked during driving, so it is
important that you confirm that the
front passenger is properly classified
prior to driving. However, the occupant
classification sensor may recalculate the
weight of the occupant under some con-
ditions (both while driving and when
stopped), so front passenger seat occu-
pants should continue to remain seated
as outlined above.

Troubleshooting

If you think the front passenger air bag
status light is incorrect:

1. If the light is ON with an adult occupying

the front passenger seat:

• Occupant is a small adult — the air bag

light is functioning as intended. The front
passenger air bag and front passenger
supplemental knee air bag are sup-
pressed.

However, if the occupant is not a small
adult, then this may be due to the following
conditions that may be interfering with the
weight sensors:
• Occupant is not sitting upright, leaning

against the seatback, and centered on
the seat cushion with his/her feet com-
fortably extended to the floor.

• A child restraint or other object pressing

against the rear of the seatback.

• A rear passenger pushing or pulling on

the back of the front passenger seat.

• Forcing the front seat or seatback against

an object on the seat or floor behind it.

• An object placed under the front passen-

ger seat.

• An object placed between the seat cush-

ion and center console or between the
seat cushion and the door.

If the vehicle is moving, please come to a
stop when it is safe to do so. Check and
correct any of the above conditions. Re-
start the vehicle and wait 1 minute.

NOTE:

A system check will be performed during
which the front passenger air bag status
light will remain lit for about 7 seconds
initially.

1-56

Safety-Seats, seat belts and supplemental restraint system

If the light is still ON after this, the person
should be advised not to ride in the front
passenger seat and the vehicle should be
checked as soon as possible. It is recom-
mended that you visit a NISSAN dealer for
this service.

2. If the light is OFF with a small adult, child

or child restraint occupying the front
passenger seat.

This may be due to the following condi-
tions that may be interfering with the
weight sensors:

• Small adult or child is not sitting upright,

leaning against the seatback, and cen-
tered on the seat cushion with his/her
feet comfortably extended to the floor.

• The child restraint is not properly in-

stalled, as outlined in “Child restraints”
(P. 1-21).

• An object weighing over 9.1 lbs. (4 kg)

hanging on the seat or placed in the seat-
back pocket (if so equipped).

• A child restraint or other object pressing

against the rear of the seatback.

• A rear passenger pushing or pulling on

the back of the front passenger seat.

• Forcing the front seat or seatback

against an object on the seat or floor be-
hind it.

• An object placed under the front passen-

ger seat.

• An object placed between the seat cush-

ion and center console.

If the vehicle is moving, please come to a
stop when it is safe to do so. Check and
correct any of the above conditions. Re-
start the vehicle and wait 1 minute.

NOTE:

A system check will be performed during
which the front passenger air bag status
light will remain lit for about 7 seconds
initially.

If the light is still OFF after this, the small
adult, child or child restraint should be re-
positioned in the rear seat and the vehicle
should be checked as soon as possible. It is
recommended that you visit a NISSAN
dealer for this service.

3. If the light is OFF with no front passenger

and no objects on the front passenger
seat, the vehicle should be checked. It is
recommended that you visit a NISSAN
dealer as soon as possible.

Other supplemental front-impact air
bag precautions

WARNING

•

Do not place any objects on the
steering wheel pad or on the instru-
ment panel. Also, do not place any
objects between any occupant and
the steering wheel or instrument
panel. Such objects may become
dangerous projectiles and cause in-
jury if the front air bags inflate.

•

Immediately after inflation, several
front air bag system components will
be hot. Do not touch them; you may
severely burn yourself.

•

No unauthorized changes should be
made to any components or wiring
of the supplemental air bag system.
This is to prevent accidental inflation
of the supplemental air bag or dam-
age to the supplemental air bag
system.

•

Do not make unauthorized changes
to your vehicle's electrical system,
suspension system or front end
structure. This could affect proper
operation of the front air bag system.

Safety-Seats, seat belts and supplemental restraint system

1-57

•

Tampering with the front air bag sys-
tem may result in serious personal
injury. Tampering includes changes
to the steering wheel and the instru-
ment panel assembly by placing ma-
terial over the steering wheel pad
and above the instrument panel or
by installing additional trim material
around the air bag system.

•

Removing or modifying the front
passenger seat may affect the func-
tion of the air bag system and result
in serious personal injury.

•

Modifying or tampering with the
front passenger seat may result in
serious personal injury. For example,
do not change the front seats by
placing material on the seat cushion
or by installing additional trim mate-
rial, such as seat covers, on the seat
that are not specifically designed to
assure proper air bag operation. Ad-
ditionally, do not stow any objects
under the front passenger seat or the
seat cushion and seatback. Such ob-
jects may interfere with the proper
operation of the occupant classifica-
tion sensor (weight sensor).

•

No unauthorized changes should be
made to any components or wiring
of the seat belt system. This may af-
fect the front air bag system. Tam-
pering with the seat belt system may
result in serious personal injury.

•

It is recommended that you visit a
NISSAN dealer for work on and
around the front air bag. It is also rec-
ommended that you visit a NISSAN
dealer for installation of electrical
equipment. The Supplemental Re-
straint System (SRS) wiring har-
nesses* should not be modified or
disconnected. Unauthorized electri-
cal test equipment and probing de-
vices should not be used on the air
bag system.

•

A cracked windshield should be re-
placed immediately by a qualified re-
pair facility. A cracked windshield
could affect the function of the
supplemental air bag system.

*The SRS wiring harness connectors are
yellow and orange for easy identification.

When selling your vehicle, we request that
you inform the buyer about the front air
bag system and guide the buyer to the
appropriate

sections

this

Owner's

Manual.

1-58

Safety-Seats, seat belts and supplemental restraint system

Front and rear outboard
seat-mounted side-impact
supplemental air bag and
roof-mounted curtain
side-impact and rollover
supplemental air bag systems

The side air bags are located in the outside
of the seatback of the front and rear out-
board seats. The curtain air bags are lo-
cated in the side roof rails.

All of the infor-

mation, cautions and warnings in this
manual must be followed.

The side air

bags and curtain air bags are designed to
inflate in higher severity side collisions, al-

though they may inflate if the forces in an-
other type of collision are similar to those of
a higher severity impact. They are de-
signed to inflate on the side where the ve-
hicle is impacted. They may not inflate in
certain side collisions.

Curtain air bags are also designed to inflate
in certain types of rollover collisions or near
rollovers. As a result, certain vehicle move-
ments (for example, during severe off-
roading) may cause the curtain air bags to
inflate.

Vehicle damage (or lack of it) is not always
an indication of proper side air bag and
curtain air bag operation.

When the side air bags and curtain air bags
inflate, a fairly loud noise may be heard,
followed by the release of smoke. This
smoke is not harmful and does not indi-
cate a fire. Care should be taken not to
inhale it, as it may cause irritation and
choking. Those with a history of a breath-
ing condition should get fresh air promptly.

Side air bags, along with the use of seat
belts, help to cushion the impact force on
the chest and pelvic area of the front and
rear outboard occupants. Curtain air bags
help to cushion the impact force to the
head of occupants in the front and rear

outboard seating positions. They can help
save lives and reduce serious injuries. How-
ever, an inflating side air bag and curtain air
bag may cause abrasions or other injuries.
Side air bags and curtain air bags do not
provide restraint to the lower body.

The seat belts should be correctly worn
and the driver, front passenger and rear
outboard occupants seated upright as far
as practical away from the side air bag.
Rear seat passengers should be seated as
far away as practical from the door finish-
ers and side roof rails. The side air bags and
curtain air bags inflate quickly in order to
help protect the occupants. Because of
this, the force of the side air bag and curtain
air bag inflating can increase the risk of
injury if the occupant is too close to, or is
against, these air bag modules during in-
flation. The side air bag will deflate quickly
after the collision is over.

The curtain air bag will remain inflated for a
short time.

The side air bags and curtain air bags
operate only when the ignition switch is
placed in the ON position.

LRS3142

Safety-Seats, seat belts and supplemental restraint system

1-59

After placing the ignition switch in the
ON position, the supplemental air bag
warning light illuminates. The supple-
mental air bag warning light will turn off
after about 7 seconds if the system is
operational.

WARNING

•

Do not place any objects near the
seatback of the front and rear seats.
Also, do not place any objects (an
umbrella, bag, etc.) between the front
and rear door finisher and the front
and rear seat. Such objects may be-
come

dangerous

projectiles

and

cause injury if a side air bag inflate.

•

Right after inflation, several side air
bag and curtain air bag system com-
ponents will be hot. Do not touch
them;

you

may

severely

burn

yourself.

•

No unauthorized changes should be
made to any components or wiring
of the side air bag and curtain air bag
systems. This is to prevent damage
to or accidental inflation of the side
air bag and curtain air bag or dam-
age to the side air bag and curtain air
bag systems.

•

Do not make unauthorized changes
to your vehicle's electrical system,
suspension system or side panel.
This could affect proper operation of
the side air bag and curtain air bag
systems.

•

Tampering with the side air bag sys-
tem may result in serious personal
injury. For example, do not change
the front and rear seats by placing
material near the seatbacks or by in-
stalling

additional

trim

material,

such as seat covers, around the side
air bag.

•

It is recommended that you visit a
NISSAN dealer for work on and
around the side air bag and curtain
air bag. It is also recommended that
you visit a NISSAN dealer for installa-
tion of electrical equipment. The SRS
wiring harnesses* should not be
modified or disconnected. Unauthor-
ized electrical test equipment and
probing devices should not be used
on the side air bag or curtain air bag
system.

* The SRS wiring harness connectors are
yellow and orange for easy identification.

When selling your vehicle, we request that
you inform the buyer about the side air bag
and curtain air bag systems and guide the
buyer to the appropriate sections in this
Owner's Manual.

1-60

Safety-Seats, seat belts and supplemental restraint system

Driver and front passenger
supplemental knee air bags

The knee air bag is located in the knee
bolster, on the driver’s and front passen-
ger’s side.

All of the information, cautions

and warnings in this manual apply and
must be followed.

The knee air bag is de-

signed to inflate in higher severity frontal
collisions, although it may inflate if the
forces in another type of collision are simi-
lar to those of a higher severity frontal im-
pact. It may not inflate in certain collisions.

Vehicle damage (or lack of it) is not always
an indication of proper knee air bag
operation.

When the knee air bag inflates, a fairly loud
noise may be heard, followed by release of
smoke. This smoke is not harmful and
does not indicate a fire. Care should be
taken not to inhale it, as it may cause irrita-
tion and choking. Those with a history of a
breathing condition should get fresh air
promptly.

The knee air bag helps to cushion the im-
pact force on the knees of the driver and
passenger. It can help reduce serious inju-
ries. However, an inflating knee air bag may
cause abrasions or other injuries. The knee
air bag provides restraint to the lower body.

The knee air bag inflates quickly in order to
help protect the occupants. Because of
this, the force of the knee air bag inflating
can increase the risk of injury if the occu-
pant is too close to, or is against, this air bag
module during inflation. The knee air bag
will deflate quickly after the collision is over
OR the knee air bag will remain inflated for
a short time.

The knee air bag operates only when the
ignition switch is placed in the ON
position.

LRS3270

Driver’s side

LRS3271

Front passenger’s side

Safety-Seats, seat belts and supplemental restraint system

1-61

WARNING

•

Do not place any objects between the
knee bolster and the driver’s or pas-
senger’s seat. Such objects may be-
come

dangerous

projectiles

and

cause injury if a knee air bag inflates.

•

Right after inflation, the knee air bag
system components will be hot. Do
not touch them; you may severely
burn yourself.

•

No unauthorized changes should be
made to any components or wiring
of the knee air bag system. This is to
prevent damage to or accidental in-
flation of the knee air bag system.

•

Do not make unauthorized changes
to your vehicle's electrical system or
suspension system. This could affect
proper operation of the knee air bag
system.

•

Tampering with the knee air bag sys-
tem may result in serious personal
injury. For example, do not change
the driver or passenger knee bolster
or install additional trim material
around the knee air bag.

•

It is recommended that you visit a
NISSAN dealer for work on and
around the knee air bag. It is also rec-
ommended that you visit a NISSAN
dealer for installation of electrical
equipment. The SRS wiring har-
nesses* should not be modified or
disconnected. Unauthorized electri-
cal test equipment and probing de-
vices should not be used on the knee
air bag system.

*The SRS wiring harness or connectors are
yellow or orange for easy identification.

When selling your vehicle, we request that
you inform the buyer about the knee air
bag system and guide the buyer to the
appropriate sections in this manual.

Seat belt with pretensioner(s)
(front and rear outboard seats)

WARNING

•

The pretensioner(s) cannot be re-
used after activation. They must be
replaced together with the retractor
and buckle as a unit.

•

If the vehicle becomes involved in a
collision but pretensioner(s) are not
activated, be sure to have the preten-
sioner system checked and, if neces-
sary, replaced. It is recommended
that you visit a NISSAN dealer for this
service.

•

No unauthorized changes should be
made to any components or wiring
of the pretensioner system. This is to
prevent damage to or accidental ac-
tivation of the pretensioner(s). Tam-
pering with the pretensioner system
may result in serious personal injury.

1-62

Safety-Seats, seat belts and supplemental restraint system

•

It is recommended that you visit a
NISSAN dealer for work on and
around the pretensioner system. It is
also recommended that you visit a
NISSAN dealer for installation of elec-
trical equipment. Unauthorized elec-
trical test equipment and probing
devices should not be used on the
pretensioner system.

•

If you need to dispose of the preten-
sioner(s) or scrap the vehicle, it is rec-
ommended that you visit a NISSAN
dealer for this service. Incorrect dis-
posal procedures could cause per-
sonal injury.

The pretensioner system may activate
with the supplemental air bag system in
certain types of collisions. Working with the
seat belt retractor, the pretensioner(s) help
tighten the seat belt when the vehicle be-
comes involved in certain types of colli-
sions, helping to restrain front and rear out-
board seat occupants.

The pretensioner(s) are encased within the
seat belt retractor and to the seat belt an-
chor affixed to the floor of the vehicle.
These seat belts are used the same way as
conventional seat belts.

When pretensioner(s) activate, smoke is re-
leased and a loud noise may be heard. This
smoke is not harmful and does not indi-
cate a fire. Care should be taken not to
inhale it, as it may cause irritation and
choking. Those with a history of a breath-
ing condition should get fresh air promptly.

After the pretensioner(s’) activation, load
limiters allow the seat belt to release web-
bing (if necessary) to reduce forces against
the chest.

The supplemental air bag warning light

is used to indicate malfunctions in the

pretensioner system. For additional infor-
mation, see "Supplemental air bag warning
light" (P. 1-64). If the operation of the supple-
mental air bag warning light indicates
there is a malfunction, have the system
checked. It is recommended that you visit a
NISSAN dealer for this service.

When selling your vehicle, we request that
you inform the buyer about the preten-
sioner system and guide the buyer to the
appropriate

sections

this

Owner's

Manual.

SUPPLEMENTAL AIR BAG WARNING
LABELS

Warning labels about the supplemental
front-impact air bag system are placed in
the vehicle as shown in the illustration.

WARNING

Do not use a rear-facing child restraint
on a seat protected by an air bag in
front of it. If the air bag deploys, it may
cause serious injury or death.

WRS0897

1. SRS Air bag warning labels

The warning labels are located on the
surface of the sun visor.

Safety-Seats, seat belts and supplemental restraint system

1-63

SUPPLEMENTAL AIR BAG WARNING
LIGHT

The supplemental air bag warning light,
displaying

in the instrument panel,

monitors the circuits for the air bag sys-
tems, pretensioner(s) and all related wiring.

When the ignition switch is placed in the ON
position, the supplemental air bag warning
light illuminates for about 7 seconds and
then turns off. This means the system is
operational.

If any of the following conditions occur, the
front air bag, side air bag, curtain air bag,
knee air bag and pretensioner systems
need servicing:
• The supplemental air bag warning light

remains

after

approximately

seconds.

• The supplemental air bag warning light

flashes intermittently.

• The supplemental air bag warning light

does not come on at all.

Under these conditions, the front air bag,
side air bag, curtain air bag or pretensioner
systems may not operate properly. They
must be checked and repaired. It is recom-
mended that you visit a NISSAN dealer for
this service.

WARNING

If the supplemental air bag warning
light is on, it could mean that the front
air bag, side air bag, curtain air bag,
knee air bag and/or pretensioner sys-
tems will not operate in an accident. To
help avoid injury to yourself or others,
have your vehicle checked as soon as
possible. It is recommended that you
visit a NISSAN dealer for this service.

Repair and replacement
procedure

The front air bags, side air bags, curtain air
bags, knee air bags and pretensioner(s) are
designed to inflate on a one-time-only ba-
sis. As a reminder, unless it is damaged, the
supplemental air bag warning light re-
mains illuminated after inflation has oc-
curred. These systems should be repaired
and/or replaced as soon as possible. It is
recommended that you visit a NISSAN
dealer for this service.

When maintenance work is required on the
vehicle, the front air bags, side air bags,
curtain air bags, knee air bags, pretension-
er(s) and related parts should be pointed
out to the person performing the mainte-
nance. The ignition switch should always
be placed in the LOCK position when work-
ing under the hood or inside the vehicle.

LRS0100

1-64

Safety-Seats, seat belts and supplemental restraint system

WARNING

•

Once a front air bag, side air bag, cur-
tain air bag or knee air bag has in-
flated, the air bag module will not
function again and must be replaced.
Additionally, the activated preten-
sioner(s) must also be replaced. The
air bag module and pretensioner(s)
should be replaced. It is recom-
mended that you visit a NISSAN
dealer for this service. However, the
air bag module and pretensioner(s)
cannot be repaired.

•

The front air bag, side air bag, curtain
air bag, knee air bag systems and the
pretensioner system should be in-
spected if there is any damage to the
front end or side portion of the ve-
hicle. It is recommended that you
visit a NISSAN dealer for this service.

•

If you need to dispose of the supple-
mental air bag or pretensioner sys-
tems or scrap the vehicle, it is recom-
mended that you contact a NISSAN
dealer for this service. Incorrect dis-
posal procedures could cause per-
sonal injury.

•

If there is an impact to your vehicle
from any direction, your Occupant
Classification Sensor (OCS) should be
checked to verify it is still functioning
correctly. It is recommended that you
visit a NISSAN dealer for this service.
The OCS should be checked even if no
air bags deploy as a result of the im-
pact. Failure to verify proper OCS
function may result in an improper
air bag deployment resulting in in-
jury or death.

Safety-Seats, seat belts and supplemental restraint system

1-65

Headlight//turn signal switch (P. 2-58,
2-63)

Steering wheel switch (P. 2-17, 2-35)
Audio controls (P. 4-63)

Driver's supplemental air bag (P. 1-59)
Horn (P. 2-64)

Meters and gauges (P. 2-3)
Warning and indicators lights (P. 2-8)
Vehicle information display (P. 2-17, 2-34)

Cruise control switches (P. 5-59)
Intelligent Cruise Control (ICC) switches
(if so equipped) (P. 5-61)
Bluetooth® Hands-Free Phone System
(P. 4-2, 4-68)

Wiper and washer switch (P. 2-56)

Vents (P. 4-32)

Idling stop OFF switch (if so equipped)
(P. 5-142)

Hazard warning flasher switch (P. 6-2)

10.

Front passenger air bag status light (P. 1-53)

11.

Audio system (P. 4-2, 4-45)

12.

Front passenger supplemental air bag
(P. 1-59)

13.

Glove box (P. 2-73)

14.

Front passenger supplemental knee air
bag (P. 1-61)

15.

Shift lever (P. 5-17)

16.

Push-button ignition switch (P. 5-10)

17.

Climate controls (P. 4-33, 4-40)

18.

Driver supplemental knee air bag (P. 1-61)

19.

Tilt/Telescopic steering (P. 3-25)

20.

Hood release (P. 3-20)

21.

Fuel filler door release (P. 3-22)

22.

ECO mode switch (P. 5-23)
Instrument brightness control (P. 2-63)
Trunk release (P. 3-21)
Trip reset switch (P. 2-4)

For additional information, refer to the
separate NissanConnect® Owner’s Manual.

Refer to the page number indicated in
parentheses for operating details.

LII2879

INSTRUMENT PANEL

2-2

Instruments and controls

Tachometer

Warning and indicator lights

Vehicle information display

Speedometer

Fuel gauge

Engine coolant temperature gauge

SPEEDOMETER AND ODOMETER

This vehicle is equipped with a speedom-
eter and odometer. The speedometer is
located on the right side of the meter clus-
ter. The odometer is located within the ve-
hicle information display.

LIC4212

METERS AND GAUGES

Instruments and controls

2-3

Speedometer

The speedometer indicates the vehicle
speed.

Odometer/Twin trip odometer

The odometer

and the twin trip odom-

eter

are displayed when the ignition

switch is placed in the ON position.

The odometer records the total distance
the vehicle has been driven.

The twin trip odometer records the dis-
tance of individual trips.

Changing the display

Push the TRIP/RESET switch (located on
the instrument panel) to change the dis-
play as follows:

TRIP A

→

TRIP B

→

ODO

→

TRIP A

Resetting the trip odometer

Press the OK button on the steering wheel
for more than 1 second to reset the cur-
rently displayed trip odometer to zero.

LIC2218

LIC4056

4.2 inch (11 cm) Type A (if so equipped)

LIC4416

7 inch (18 cm) Type B (if so equipped)

2-4

Instruments and controls

TACHOMETER

The tachometer indicates engine speed in
revolutions per minute (rpm).

Do not rev the engine into the red zone

CAUTION

When engine speed approaches the
red zone, shift to a higher gear or re-
duce engine speed. Operating the en-
gine in the red zone may cause serious
engine damage.

ENGINE COOLANT TEMPERATURE
GAUGE

NOTE:

The ignition switch must be placed in the
ON position for the gauge to give a
reading.

The gauge indicates the engine coolant
temperature. The engine coolant tempera-
ture is within the normal range when the
reading is within the zone

shown in the

illustration.

LIC4365

4.2 inch (11 cm) Type A (if so equipped)

LIC4602

7 inch (18 cm) Type B (if so equipped)

LIC3427

Instruments and controls

2-5

The engine coolant temperature varies
with the outside air temperature and driv-
ing conditions.

CAUTION

If the gauge indicates a coolant tem-
perature near the hot (H) end of the
normal range, reduce vehicle speed to
decrease the temperature. If the gauge
is over the normal range, stop the ve-
hicle as soon as safely possible. If the
engine is overheated, continued opera-
tion of the vehicle may seriously dam-
age the engine. For additional informa-
tion, see “If your vehicle overheats”
(P. 6-11).

FUEL GAUGE

NOTE:

The ignition switch must be placed in the
ON position for the gauge to give a
reading.

The gauge indicates the

approximate

fuel

level in the tank.

The gauge may move slightly during brak-
ing, turning, acceleration, or going up or
down hills.

The low fuel warning light comes on when
the amount of fuel in the tank is getting low.

Refill the fuel tank before the gauge reg-
isters 0 (Empty).

The arrow on the fuel pump symbol

indicates the fuel-filler location.

CAUTION

•

If the vehicle runs out of fuel, the
Malfunction Indicator Light (MIL) may
come on. Refuel as soon as possible.
After a few driving trips. the

light

should turn off. If the light remains on
after a few driving trips, have the ve-
hicle inspected. It is recommended
that you visit a NISSAN dealer for this
service.

•

For additional information, see “Mal-
function Indicator Light (MIL)” (P. 2-10).

LIC2222

2-6

Instruments and controls

DISTANCE TO EMPTY (DTE)

Displays the estimated distance the ve-
hicle can be driven before refueling. The
value is calculated based on recent fuel
economy, the amount of fuel remaining in
the

fuel

tank,

and

the

actual

fuel

consumption.

Changes in driving patterns or conditions
can cause the DTE value to vary. As a result,
the value displayed may differ from the ac-
tual distance that can be driven.

DTE display will change to “---” when the
fuel level in the tank is getting low, prior to
the fuel gauge reaching 0 (Empty).

NOTE:
• The DTE value after refill is estimated

based on recent fuel economy and
amount of fuel added.

• If a small amount of fuel is added, or

the ignition is on during refueling, the
display may not be updated.

• Conditions

that

affect

the

fuel

economy will also affect the estimated
DTE value (city/highway driving, idle
time, remote start time, terrain, sea-
sonal weather, added vehicle weight,
added deflectors, roof racks, etc.).

Instruments and controls

2-7

Warning/Indicator light (red)

Warning/Indicator light (yellow)

Warning/Indicator light (other)

Brake warning light

Anti-lock Braking System (ABS)
warning light

ECO mode indicator light (green)

Charge warning light

Automatic Emergency Braking with Pedes-
trian Detection system warning light

High Beam Assist indicator light (green) (if
so equipped)

Engine oil pressure warning light

Front passenger air bag status light

High beam indicator light (blue)

Malfunction Indicator Light (MIL)

Low tire pressure warning light

Side light and headlight indicator light
(green)

Master warning light

Turn signal/hazard indicator lights (green)

Seat belt warning light and chime

Power steering warning light

Supplemental air bag warning light

Rear Automatic Braking system warning
light

Slip indicator light

Vehicle Dynamic Control (VDC) OFF indica-
tor light

WARNING LIGHTS, INDICATOR LIGHTS
AND AUDIBLE REMINDERS

2-8

Instruments and controls

CHECKING LIGHTS

With all doors closed, apply the parking
brake, fasten the seat belts and place the
ignition switch in the ON position without
starting the engine. The following lights (if
so equipped) will come on:

The following lights (if so equipped) will
come on briefly and then go off:

If any light does not come on or operate in
a way other than described, it may indicate
a burned-out bulb and/or a system mal-
function. Have the system checked. It is
recommended that you visit a NISSAN
dealer for this service.

Some indicators and warnings are also dis-
played on the vehicle information display
between the speedometer and tachom-
eter. For additional information, see “Ve-
hicle information display 4.2 inch (11 cm)
Type A” (P. 2-17), or “Vehicle information dis-
play 7 inch (18 cm) Type B” (P. 2-34).

WARNING/INDICATOR LIGHTS (red)

For additional information on warnings
and indicators, see “Vehicle information
display 4.2 inch (11 cm) Type A” (P. 2-17) or
“Vehicle information display 7 inch (18 cm)
Type B” (P. 2-34).

Brake warning
light

This light functions for both the parking
brake and the foot brake systems.

Parking brake indicator

When the ignition switch is placed in the ON
position, the light comes on when the park-
ing brake is applied.

Low brake fluid warning light

When the ignition switch is placed in the ON
position, the light warns of a low brake fluid
level. If the light comes on while the engine
is running with the parking brake not ap-
plied, stop the vehicle and perform the
following:

1. Check the brake fluid level. Add brake

fluid as necessary. For additional infor-
mation, see “Brake fluid” (P. 8-11).

2. If the brake fluid level is correct, have the

warning system checked. It is recom-
mended that you visit a NISSAN dealer
for this service.

WARNING

•

Your brake system may not be work-
ing properly if the warning light is on.
Driving could be dangerous. If you
judge it to be safe, drive carefully to
the nearest service station for re-
pairs. Otherwise, have your vehicle
towed because driving it could be
dangerous.

•

Pressing the brake pedal with the en-
gine stopped and/or a low brake
fluid level may increase your stop-
ping distance and braking will re-
quire greater pedal effort as well as
pedal travel.

•

If the brake fluid level is below the
MINIMUM or MIN mark on the brake
fluid reservoir, do not drive until the
brake system has been checked. It is
recommended

that

you

visit

NISSAN dealer for this service.

Instruments and controls

2-9

Charge warning light

If this light comes on while the engine is
running, it may indicate the charging sys-
tem is not functioning properly. Turn the
engine off and check the generator belt. If
the belt is loose, broken, missing, or if the
light remains on, have your vehicle serviced
immediately. It is recommended that you
visit a NISSAN dealer for this service.

CAUTION

Do not continue driving if the generator
belt is loose, broken or missing.

Engine oil pressure
warning light

This light warns of low engine oil pressure. If
the light flickers or comes on during nor-
mal driving, pull off the road in a safe area,
stop the engine

immediately

and call a

NISSAN dealer or other authorized repair
shop.

The engine oil pressure warning light is
not designed to indicate a low oil level.

Use the dipstick to check the oil level. For
additional information, see “Engine oil”
(P. 8-6 ).

CAUTION

Running the engine with the engine oil
pressure warning light on could cause
serious damage to the engine almost
immediately. Such damage is not cov-
ered by warranty. Turn off the engine as
soon as it is safe to do so.

Malfunction Indicator Light
(MIL)

If this indicator light comes on steady or
blinks while the engine is running, it may
indicate

potential

emission

control

malfunction.

The MIL may also come on steady if the
fuel-filler cap is loose or missing, or if the
vehicle runs out of fuel. Check to make sure
the fuel-filler cap is installed and closed
tightly, and that the vehicle has at least
3 gallons (11.4 liters) of fuel in the fuel tank.

After a few driving trips, the

light

should turn off if no other potential emis-
sion control system malfunction exists.

If this indicator light comes on steady for 20
seconds and then blinks for 10 seconds
when the engine is not running, it indicates
that the vehicle is not ready for an emission
control system inspection/maintenance

test. For additional information, see “Readi-
ness for Inspection/Maintenance (I/M) test”
(P. 10-22).

Operation

The MIL will come on in one of two ways:
• MIL on steady — An emission control sys-

tem malfunction has been detected.
Check the fuel-filler cap if the Loose Fuel
Cap warning appears in the vehicle infor-
mation display. If the fuel-filler cap is loose
or missing, tighten or install the cap and
continue to drive the vehicle. The
light should turn off after a few driving
trips. If the

light does not turn off

after a few driving trips, have the vehicle
inspected. It is recommended that you
visit a NISSAN dealer for this service. You
do not need to have your vehicle towed
to the dealer.

• MIL blinking — An engine misfire has been

detected which may damage the emis-
sion control system. To reduce or avoid
emission control system damage:

– do not drive at speeds above 45 mph

(72 km/h).

– avoid hard acceleration or decelera-

tion.

– avoid steep uphill grades.
– if possible, reduce the amount of cargo

being hauled or towed.

2-10

Instruments and controls

The MIL may stop blinking and come on
steady. Have the vehicle inspected. It is rec-
ommended that you visit a NISSAN dealer
for this service. You do not need to have
your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could lead to poor driveability, reduced
fuel economy, and possible damage to
the emission control system.

Master warning light

When the ignition switch is in the ON posi-
tion, the master warning light illuminates if
any of the following are displayed on the
vehicle information display:
• Parking brake release warning
• Door open (when vehicle is moving)

warning

• Service CVT Stop safely warning
• Shift to P (Park) position warning

For additional information, see “Vehicle in-
formation display 4.2 inch (11 cm) Type A”
(P. 2-17) or “Vehicle information display 7
inch (18 cm) Type B” (P. 2-34).

Seat belt warning light and
chime

• The light and chime remind you to fasten

the seat belts.

• The seat belt warning light will illuminate

when the ignition switch is pushed to the
ON position if the driver’s seat belt is not
fastened, or if the front passenger seat
belt is not fastened when occupied.

• The seat belt warning light will also illumi-

nate if a rear passenger seat belt is
changed from fastened to unfastened.

• If the driver’s seat belt is not fastened

when the ignition switch is pushed to the
ON position, the chime will sound shortly.

• If the vehicle is driven above 9 mph (15

km/h) in the conditions that illuminate
the seat belt warning light, the lamp will
begin to blink and the chime will sound
for over one minute, or until the seat belt
is fastened again.

NOTE:

•

The warning light and/or chime may
activate if an object is placed in the un-
occupied front passenger seat. In this
case, please remove the object from
the front passenger seat.

•

The warning light and/or chime may
activate if any seat belt is unfastened
before the vehicle comes to a complete
stop. Please remain fastened until the
vehicle has come to a complete stop.

Supplemental air bag
warning light

When the ignition switch is placed in the ON
position, the supplemental air bag warning
light illuminates for about 7 seconds and
then turns off. This means the system is
operational.

If any of the following conditions occur, the
front air bag, side air bag, curtain air bag,
and pretensioner seat belt systems need
servicing.
• The supplemental air bag warning light re-

mains on after approximately 7 seconds.

• The supplemental air bag warning light

flashes intermittently.

• The supplemental air bag warning light

does not come on at all.

It is recommended that you visit a NISSAN
dealer for these services. Unless checked
and repaired, the supplemental restraint
system (air bag system) and/or the preten-
sioners may not function properly. For ad-
ditional information, see “Supplemental re-
straint system (SRS)” (P. 1-42).

Instruments and controls

2-11

WARNING

If the supplemental air bag warning
light is on, it could mean that the front
air bag, side air bag, curtain air bag sys-
tems and/or pretensioner systems will
not operate in an accident. To help
avoid injury to yourself or others, have
your vehicle checked as soon as pos-
sible. It is recommended that you visit a
NISSAN dealer for this service.

WARNING/INDICATOR LIGHTS
(yellow)

For additional information on warnings
and indicators, see “Vehicle information
display 4.2 inch (11 cm) Type A” (P. 2-17) or
“Vehicle information display 7 inch (18 cm)
Type B” (P. 2-34).

Anti-lock Braking
System (ABS)
warning light

When the ignition switch is placed in the ON
position, the ABS warning light illuminates
and then turns off. This indicates the ABS is
operational.

If the ABS warning light illuminates while
the engine is running or while driving, it

may indicate the ABS is not functioning
properly. Have the system checked. It is
recommended that you visit a NISSAN
dealer for this service.

If an ABS malfunction occurs, the anti-lock
function is turned off. The brake system
then operates normally but without anti-
lock assistance. For additional information,
see “Brake system” (P. 5-126).

Automatic Emergency
Braking (AEB) with
Pedestrian Detection
system warning light

This light comes on when the ignition
switch is placed in the ON position. It turns
off after the engine is started.

This light illuminates when the AEB with
Pedestrian Detection system is set to OFF
in the vehicle information display.

If the light illuminates or flashes when the
AEB with Pedestrian Detection system is
on, it may indicate that the system is un-
available. For additional information, see
“Automatic Emergency Braking (AEB) with
Pedestrian Detection” (P. 5-91) and “Intelli-
gent Forward Collision Warning (I-FCW)”
(P. 5-104).

Front passenger air bag
status light

The front passenger air bag status light will
be lit and the passenger front air bag will be
off depending on how the front passenger
seat is being used.

For additional information, see “Front pas-
senger air bag and status light” (P. 1-53).

Low tire pressure warning
light

Your vehicle is equipped with a Tire Pres-
sure Monitoring System (TPMS) that moni-
tors the tire pressure of all tires except the
spare.

The low tire pressure warning light warns
of low tire pressure or indicates that the
TPMS is not functioning properly.

After the ignition switch is placed in the ON
position, this light illuminates for about 1
second and turns off.

Low tire pressure warning

If the vehicle is being driven with low tire
pressure, the warning light will illumi-
nate. The “Tire Pressure Low – Add Air”
appears

the

vehicle

information

display.

2-12

Instruments and controls

When the low tire pressure warning light
illuminates, you should stop and adjust
the tire pressure of all four tires to the
recommended COLD tire pressure shown
on the Tire and Loading Information la-
bel located in the driver’s door opening.
The low tire pressure warning light does
not automatically turn off when the tire
pressure is adjusted. After the tire is in-
flated to the recommended pressure,
the vehicle must be driven at speeds
above 16 mph (25 km/h) to activate the
TPMS and turn off the low tire pressure
warning light. Use a tire pressure gauge
to check the tire pressure.

The “Tire Pressure Low - Add Air” warning
appears each time the ignition switch is
placed in the ON position as long as the
low tire pressure warning light remains
illuminated.

For additional information, see “Vehicle in-
formation display 4.2 inch (11 cm) Type A”
(P. 2-17), “Vehicle information display 7 inch
(18 cm) Type B” (P. 2-34) and “Tire Pressure
Monitoring System (TPMS)” (P. 5-5).

TPMS malfunction

If the TPMS is not functioning properly, the
low tire pressure warning light will flash for
approximately 1 minute when the ignition
switch is placed in the ON position. The
light will remain on after 1 minute. Have the
system checked. It is recommended that
you visit a NISSAN dealer for this service.
The “Tire Pressure Low— Add Air” warning
does not appear if the low tire pressure
warning light illuminates to indicate a
TPMS malfunction.

For additional information, see “Tire Pres-
sure Monitoring System (TPMS)” (P. 5-5) and
“Tire pressure” (P. 8-29).

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

•

If the light does not illuminate with
the ignition switch placed in the ON
position, have the vehicle checked as
soon as possible. It is recommended
that you visit a NISSAN dealer for this
service.

•

If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt

braking,

reduce

vehicle

speed, pull off the road to a safe loca-
tion and stop the vehicle as soon as
possible. Driving with under-inflated
tires may permanently damage the
tires and increase the likelihood of
tire failure. Serious vehicle damage
could occur and may lead to an acci-
dent and could result in serious per-
sonal injury or death. Check the tire
pressure for all four tires. Adjust the
tire pressure to the recommended
COLD tire pressure show on the Tire
and Loading Information label lo-
cated in the driver’s door opening to
turn the low tire pressure warning
light off. If the light still illuminates
while driving after adjusting the tire
pressure, a tire may be flat or the
TPMS may be malfunctioning. If you
have a flat tire, replace it with a spare
tire as soon as possible. If no tire is
flat and all tires are properly inflated,
have the vehicle checked. It is recom-
mended that you visit a NISSAN
dealer for this service.

Instruments and controls

2-13

•

When using a wheel without the
TPMS such as the spare tire, the TPMS
will not function and the low tire
pressure warning light will flash for
approximately 1 minute. The light will
remain on after 1 minute. Have your
tires replaced and/or TPMS system
reset as soon as possible. It is recom-
mended that you visit a NISSAN
dealer for these services.

•

Replacing tires with those not origi-
nally specified by NISSAN could af-
fect the proper operation of the
TPMS.

CAUTION

•

The TPMS is not a substitute for the
regular tire pressure check. Be sure
to check the tire pressure regularly.

•

If the vehicle is being driven at
speeds of less than 16 mph (25 km/h),
the TPMS may not operate correctly.

•

Be sure to install the specified size of
tires to the four wheels correctly.

Master warning light

When the ignition switch is in the ON posi-
tion, the master warning light illuminates if
any of the following are displayed on the
vehicle information display:
• Low washer fluid warning
• Loose fuel cap warning
• Low tire pressure warning
• Emergency brake warning
• Lock warning
• Shipping mode warning
• Door/Trunk open warning (when vehicle

is moving)

• LED Headlight system warning (if so

equipped)

• Chassis Control system fault warning (if

so equipped)

• Service CVT warnings
• Service engine warnings
• Rear emergency braking warning (If so

equipped)

• Parking sensor error warning
• Driver Attention Alert warning (if so

equipped)

• ITS system malfunction warning

• Traffic Sign Recognition warnings (if so

equipped)

• I-Key system warnings

For additional information, see “Vehicle in-
formation display 4.2 inch (11 cm) Type A”
(P. 2-17) or “Vehicle information display 7
inch (18 cm) Type B” (P. 2-34).

Power steering warning
light

WARNING

•

If the engine is not running or is
turned off while driving, the power
assist for the steering will not work.
Steering will be harder to operate.

•

When the power steering warning
light illuminates with the engine run-
ning, there will be no power assist for
the steering. You will still have control
of the vehicle but the steering will be
harder to operate. Have the power
steering system checked. It is recom-
mended that you visit a NISSAN
dealer for this service.

When the ignition switch is placed in the ON
position, the power steering warning light
illuminates. After starting the engine, the

2-14

Instruments and controls

power steering warning light turns off. This
indicates the power steering system is
operational.

If the power steering warning light illumi-
nates while the engine is running, it may
indicate the power steering system is not
functioning properly and may need servic-
ing. Have the power steering system
checked. It is recommended that you visit a
NISSAN dealer for this service.

When the power steering warning light illu-
minates with the engine running, there will
be no power assist for the steering but you
will still have control of the vehicle. At this
time, greater steering effort is required to
operate the steering wheel, especially in
sharp turns and at low speeds.

For additional information, see “Power
steering” (P. 5-125).

Rear Automatic Braking
(RAB) system warning light

This light comes on when the ignition
switch is placed in the ON position. It turns
off after the engine is started.

This light illuminates when the RAB system
is turned off in the vehicle information
display.

If the light illuminates or flashes when the
RAB system is on, it may indicate that the
system is unavailable. For additional infor-
mation, see “Rear Automatic Braking (RAB)”
(P. 5-84).

Slip indicator light

This indicator will blink when the Vehicle
Dynamic Control (VDC) system is operat-
ing, thus alerting that the vehicle is nearing
its traction limits. The road surface may be
slippery.

You may feel or hear the system working;
this is normal.

The light will blink for a few seconds after
the VDC system stops limiting wheel spin.

The

indicator light also comes on

when you place the ignition switch in the
ON position. The light will turn off after ap-
proximately 2 seconds if the system is op-
erational. If the light does not come on
have the system checked. it is recom-
mended that you visit a NISSAN dealer for
this service.

Vehicle Dynamic Control
(VDC) OFF indicator light

This indicator light comes on when the
VDC is turned off in the vehicle information
display. This indicates the VDC has been
turned off.

Turn the VDC on using the vehicle informa-
tion display, or by restarting the engine. For
additional information, see “Vehicle Dy-
namic Control (VDC) system” (P. 5-128).

The VDC light also comes on when the ig-
nition switch is placed in the ON position.
The light will turn off after a period of time if
the system is operational. If the light stays
on or comes on along with the

indica-

tor light while you are driving, have the VDC
system checked. It is recommended that
you visit a NISSAN dealer for this service.

WARNING

VDC should remain on unless freeing a
vehicle from mud or snow.

While the VDC system is operating, you
might feel a slight vibration or hear the sys-
tem working when starting the vehicle or
accelerating, but this is normal.

Instruments and controls

2-15

WARNING/INDICATOR LIGHTS
(other)

For additional information on warnings
and indicators, see “Vehicle information
display 4.2 inch (11 cm) Type A” (P. 2-17) or
“Vehicle information display 7 inch (18 cm)
Type B” (P. 2-34).

ECO mode indicator light
(green)

This light comes on when the ECO mode
has been selected. For additional informa-
tion, see “ECO mode switch” (P. 5-23).

High Beam Assist indicator
light (green) (if so equipped)

This indicator light illuminates when the
headlights come on while the headlight
switch is in the AUTO position with the high
beams selected. This indicates that the
high beam assist is operational.

For additional information, see “Headlight
and turn signal switch” (P. 2-58).

High beam indicator light
(blue)

This blue light comes on when the head-
light high beams are on and goes out when
the low beams are selected.

The high beam indicator light also comes
on when the passing signal is activated.

Side light and headlight
indicator light (green)

The side light and headlight indicator light
illuminates when the side light or headlight
position is selected. For additional informa-
tion, see “Headlight and turn signal switch”
(P. 2-58).

Turn signal/hazard
indicator lights (green)

The appropriate light flashes when the turn
signal switch is activated.

Both lights flash when the hazard switch is
turned on.

AUDIBLE REMINDERS

Brake pad wear warning

The disc brake pads have audible wear
warnings. When a disc brake pad requires
replacement, it makes a high pitched
scraping sound when the vehicle is in mo-
tion, whether or not the brake pedal is de-
pressed. Have the brakes checked as soon
as possible if the warning sound is heard.

Light reminder chime

With the ignition switch placed in the OFF
position, a chime sounds when the driver's
door is opened if the headlights or parking
lights are on.

Turn the headlight control switch off before
leaving the vehicle.

2-16

Instruments and controls

NISSAN Intelligent Key® door
buzzer

The Intelligent Key door buzzer sounds if
any one of the following improper opera-
tions is found.
• The Intelligent Key is left inside the vehicle

when locking the doors and trunk.

• The Intelligent Key is taken outside the

vehicle when operating the vehicle.

• Any doors are not closed securely when

locking the doors.

When the buzzer sounds, be sure to check
both the vehicle and the Intelligent Key.

For additional information, see “NISSAN In-
telligent Key®” (P. 3-6).

Parking brake reminder chime

A chime sounds if the parking brake is set
and the vehicle is driven. The chime will
stop if the parking brake is released or the
vehicle speed returns to zero.

The vehicle information display is located
to the left of the speedometer. It displays
such items as:
• Vehicle settings
• Trip computer information
• Drive system warnings and settings
• Cruise control system information
• NISSAN Intelligent Key® operation infor-

mation

• Indicators and warnings

HOW TO USE THE VEHICLE
INFORMATION DISPLAY

The vehicle information display can be
changed using the

, and OK buttons located on the steer-

ing wheel.

䊊

- Use these buttons

to navigate the vehicle information
display.

䊊

OK - Change or select an item in the
vehicle information display.

䊊

— Returns to the previous menu.

LIC2630

LIC3566

VEHICLE INFORMATION DISPLAY 4.2
INCH (11 cm) TYPE A (if so equipped)

Instruments and controls

2-17

The OK,

and

buttons also

control audio and control panel functions
in some conditions. Most screens and
menus offer instruction prompts of the
steering switch buttons to indicate how to
control the vehicle information display. The
OK button changes the audio source and
the

buttons also control voice

recognition manual mode. The OK button
can be used to change the audio source
when the audio screen is displayed. The

buttons can be used when con-

trolling voice recognition prompts manu-
ally. For additional information, refer to the
separate NissanConnect® Owner’s Manual.

STARTUP DISPLAY

When the vehicle in placed in the ON posi-
tion the screens that display in the vehicle
information include:
• Active system status (if so equipped)
• Trip computer
• Fuel economy
• Warnings
• Outside air temperature
• Odometer/Twin Trip Odometer

Warnings will only display if there are any
present. For additional information, see
“Vehicle information display warnings and
indicators” (P. 2-28).

2-18

Instruments and controls

1. Vehicle speed

The vehicle speed mode shows the current
vehicle speed and the average vehicle
speed since the last reset.

Average vehicle speed:

Press the OK button on the steering wheel
to bring up the drive computer Reset
menu, and follow the instructions to reset.

For additional information, see “Resetting
the drive computer” (P. 2-39).

The average vehicle display is updated ev-
ery 30 seconds. the first 30 seconds after a
rest, the display shows “– – –’

2. Elapsed time and trip odometer

Elapsed time:

The elapsed time shows the time since the
last reset. Press the OK button to bring up
the drive computer Reset menu, and follow
the instructions to reset.

For additional information, see “Resetting
the drive computer” (P. 2-39).

Trip odometer:

The trip odometer shows the total dis-
tance the vehicle has been driven since the
last reset. Press the OK button on the steer-
ing wheel to bring up the drive computer
Reset menu, and follow the instructions to
reset.

For additional information, see “Resetting
the drive computer” (P. 2-39).

3. Fuel economy display

Current fuel consumption:

The current fuel consumption mode shows
the current fuel consumption.

Average fuel consumption:

The average fuel consumption mode
shows the average fuel consumption since
the last reset. Press the OK button on the
steering wheel to bring up the drive com-
puter Reset menu, and follow the instruc-
tions to reset.

For additional information, see “Resetting
the drive computer” (P. 2-39).

The display is updated every 30 seconds.
For about the first 1/3 of a mile (500 m) after
a reset, the display shows “– –.”

4. Audio

The audio mode shows the status of audio
information.

5. Driving Aids

The driving aids mode shows the operat-
ing condition for the following systems
(if so equipped):
• Forward

–– Automatic Emergency Braking (AEB)

with Pedestrian Detection system

–– Intelligent Forward Collision Warning

(I-FCW)

• Lane:

–– Lane Departure Warning (LDW)

• Blind Spot:

–– Blind Spot Warning (BSW)

For additional information, see “Blind Spot
Warning (BSW)” (P. 5-36), “Lane Departure
Warning (LDW)” (P. 5-29), “Automatic Emer-
gency Braking (AEB) with Pedestrian Detec-
tion” (P. 5-91), or“Intelligent Forward Collision
Warning (I-FCW)” (P. 5-104).

2-20

Instruments and controls

6. Tire Pressures

The tire pressure mode shows the pres-
sure of all four tires while the vehicle is
driven.

When the “Tire Pressure Low — Add Air”
warning appears, the display can be
switched to the tire pressure mode by
pressing the OK button to reveal additional
details on the displayed warning.

For additional information, see “Low tire
pressure warning light” (P. 2-12), “Tire Pres-
sure Monitoring System (TPMS)” (P. 5-5), “Flat
tire” (P. 6-3) and “Types of tires” (P. 8-36)

7. Warnings

The warnings mode allows the driver to
view any present warnings.

NOTE:

The warnings mode will only display if
any are present.

8. Settings

The settings mode allows the driver to view
or modify settings.

SETTINGS

The setting mode allows you to change the
information displayed in the vehicle infor-
mation display:
• VDC Setting
• Driver Assistance
• ECO Mode Setting
• TPMS Settings
• Clock
• Vehicle Settings
• Maintenance
• Customize Display
• Unit
• Language
• Factory Reset

VDC Setting

The VDC Setting menu allows the user to enable or disable the Vehicle Dynamic Control (VDC) system.

Menu item

Explanation

System

Allows the user turn the VDC system on or off. For additional information, see “Vehicle Dynamic Control (VDC)
system” (P. 5-128).

Instruments and controls

2-21

Nissan Sentra (2024 year). Manual in english - page 3