Nissan Murano (2024 year). Manual in english

1. To block glare from the front, swing

down

the main sun visor.

2. To block glare from the side, remove the

main sun visor from the center mount
and swing the visor to the side

3. To extend

the sun visor, slide in or out

as needed.

CAUTION

•

Do not store the sun visor before re-
turning the extension to its original
position.

•

Do not pull the extension sun visor
forcedly downward.

VANITY MIRRORS

To access the vanity mirror, pull the sun
visor down and flip open the mirror cover.
The vanity mirror will illuminate when the
mirror cover is open.

WPD0344

LPD2703

SUN VISORS

3-32

Pre-driving checks and adjustments

CARD HOLDER

To use the card holder, slide card into the
clip. Do not view information while operat-
ing the vehicle.

MANUAL ANTI-GLARE REARVIEW
MIRROR (if so equipped)

Use the night position

to reduce glare

from the headlights of vehicles behind you
at night.

Use the day position

when driving in

daylight hours.

WARNING

Use the night position only when nec-
essary, because it reduces rear view
clarity.

AUTOMATIC ANTI-GLARE
REARVIEW MIRROR (if so equipped)

The inside mirror is designed so that it au-
tomatically dims during nighttime condi-
tions and according to the intensity of the
headlights of the vehicle following you. The
automatic anti-glare feature is activated
when the ignition switch is in the ON
position.

NOTE:

Do not hang any objects over the sen-
sors

or apply glass cleaner to the sen-

sors. Doing so will reduce the sensitivity
of the sensors, resulting in improper
operation.

LPD2340

Driver’s and passenger’s side

WPD0126

MIRRORS

Pre-driving checks and adjustments

3-33

Type A (if so equipped)

NOTE:

Do not hang any objects over the sen-
sors

or apply glass cleaner to the sen-

sors. Doing so will reduce the sensitivity
of the sensors, resulting in improper
operation.

Type B (if so equipped)

For additional information on HomeLink®
Universal

Transceiver

operation,

see

“HomeLink® Universal Transceiver” (P. 2-74).

NOTE:

Do not hang any objects over the sen-
sors

or apply glass cleaner to the sen-

sors. Doing so will reduce the sensitivity
of the sensors, resulting in improper
operation.

OUTSIDE MIRRORS

WARNING

•

Do not adjust the mirrors while driv-
ing. You could lose control of your
vehicle and cause an accident.

•

Objects viewed in the outside mirror
on the passenger side are closer than
they appear. Be careful when moving
to the right. Using only this mirror
could cause an accident. Use the
inside mirror or glance over your
shoulder to properly judge distances
to other objects.

LPD2418

LPD3366

3-34

Pre-driving checks and adjustments

Manual folding outside mirrors

Pull the outside mirror toward the door to
fold it.

Electric control type

The outside mirror remote control will op-
erate only when the ignition switch is in the
ACC or ON position.

Move the small switch

to select the left

or right mirror. Adjust each mirror to the
desired position using the large switch

Move the small switch to the center (neu-
tral) position to prevent accidentally mov-
ing the mirror.

Heated mirrors

Some outside mirrors can be heated to
defrost, defog, or de-ice for improved
visibility. For additional information, see
“Rear window and outside mirror defroster
switch” (P. 2-40).

Reverse tilt-down feature (if so
equipped)

The reverse tilt-down feature will turn both
outside mirror surfaces downward to pro-
vide better rear visibility close to the vehicle
when the mirror control switch is in either
the L or R position.

The mirrors automatically return to their
original position when you shift out of R
(Reverse).

The outside mirror surfaces will return to
their original position when one of the fol-
lowing conditions has occurred:
• The shift lever is moved to any position

other than R (Reverse).

• The outside mirror control switch is set to

the neutral or center position.

• The ignition switch is placed in the OFF

position.

LPD2112

LPD2452

Pre-driving checks and adjustments

3-35

NOTE:

If the outside mirror control switch is in
the center position, the mirror surface
will NOT turn downward when the shift
lever is moved to R (Reverse).

For additional information, see “Memory
seat” (P. 3-36).

The memory seat system has three
features:
• Memory storage function (Key-link)
• Memory storage function (Switch)
• Entry/exit function

Key-link, when enabled, automatically re-
tains the driver’s last seat, outside mirrors
and steering wheel (if so equipped) posi-
tions for that specific key when the ignition
is turned from ON to OFF.

Each memory switch button (1 or 2) on the
driver’s door can also store one additional
position which is independent of the key-
linked position.

MEMORY STORAGE FUNCTION
(key link)

Use the following process to setup key link:

1. Unlock the vehicle with the desired Intel-

ligent Key while the ignition is OFF.

2. Place the ignition in the ON position or

start the engine.

3. Within the “Settings” menu of the touch

screen display, select “Edit User” and
then “Sync Profile with Intelligent Key”.

4. Turn “Sync Profile with Intelligent Key”

ON. The ON button will light up.

5. Within the “Settings” menu of the touch-

screen display, select “Edit User” and
then “User Profiles”.

6. Create a personal profile and make sure

the correct key number is selected with
the arrow.

7. Set the desired seat, steering and mirror

position.

8. Place the ignition switch in the OFF po-

sition and lock the vehicle with the Intel-
ligent Key.

Once step 8 is completed, every time the
vehicle is unlocked using the Intelligent Key
and the ignition is placed in the ON posi-
tion, the memory position will be recalled.

Follow the same procedure if you want
to link the 2nd, 3rd or 4th Intelligent Key.

NOTE:
• If new memory positions are set prior

to turning the ignition from ON to OFF,
the previously linked memory posi-
tions for the respective key will be
overwritten by new positions.

• If more than one key is in the vehicle

during the Intelligent Key memory
setup, memory may not be set to the
correct key.

MEMORY SEAT (if so equipped)

3-36

Pre-driving checks and adjustments

Recalling Intelligent Key memory
positions

If the “Key-Linked Settings” are enabled in
the vehicle information display for that par-
ticular key, every time you enter the vehicle
the driver’s seat, mirrors and automatic
steering wheel (if so equipped) will auto-
matically move to the driver’s last position
of the respective Intelligent Key.

NOTE:

The key-linked memory positions can be
different from the positions stored in the
memory switch (1 or 2).

MEMORY STORAGE FUNCTION
(switch)

Use the following process to manually
store the two memory positions in the
switch:

NOTE:

The vehicle should be stopped while set-
ting the memory.

1. Adjust the driver's seat, outside mirrors

and steering wheel (if so equipped) to
the desired positions by manually oper-
ating each adjusting switch. For addi-
tional information, see “Seats” (P. 1-2).

2. Push the SET switch and, within 5 sec-

onds, push the memory switch (1 or 2).

The indicator light for the pushed memory
switch will come on and stay on for ap-
proximately 5 seconds. The chime will
sound when the memory is stored.

NOTE:

If a new memory position is stored in the
same memory switch, the previous
memory position will be overwritten by
the new stored position.

Recalling switch memory
positions

To recall the manually stored positions,
push the memory switch (1 or 2). The driv-
er’s seat and automatic steering wheel (if
so equipped) will move to the positions
stored to those buttons.

LPD3343

Pre-driving checks and adjustments

3-37

ENTRY/EXIT FUNCTION (if so
equipped)

This system is designed so that the driver's
seat and steering column will automati-
cally move when the shift lever is in the P
(Park) position. This allows the driver to
easily get in and out of the driver’s seat.

The driver’s seat will slide backward and
the steering wheel will move up when the
ignition is switched to OFF and the driver’s
door is open.

The driver’s seat and steering wheel will
return to the previous position when the
ignition switch is switched to ON.

The entry/exit function can be enabled or
disabled through the “Vehicle Settings” in
the vehicle information display by perform-
ing the following:
• Switch the Exit Seat Slide from ON to OFF.
• Switch the Exit Steering Up from ON to

OFF.

Restarting the entry/exit function

If the battery cable is disconnected or if the
fuse opens, the stored memory positions
may be lost and some of the functions will
be restricted.

1. Drive the vehicle over 25 mph (40 km/h).

2. Open and close the driver's door more

than two times with the ignition switch
in the OFF position.

The entry/exit function should now work
properly.

SYSTEM OPERATION

The memory seat system will not work or
will stop operating under the following
conditions:
• When the vehicle speed is above 4 mph

(7 km/h).

• When any of the memory switches are

pushed while the memory seat system is
operating.

• When the switch for the driver’s seat and

steering wheel is pushed while the
memory seat system is operating.

• When the seat has already been moved

to the memorized position.

• When no seat position is stored in the

memory switch.

• When the shift position is moved from P

(Park) to any other position.

3-38

Pre-driving checks and adjustments

1. CAMERA button

WARNING

•

Failure to follow the warnings and in-
structions for proper use of the Rear-
View Monitor system could result in
serious injury or death.

•

RearView Monitor is a convenience
feature and is not a substitute for
proper backing. Always turn and look
out the windows and check mirrors
to be sure that it is safe to move be-
fore operating the vehicle. Always
back up slowly.

•

The system is designed as an aid to
the driver in showing large station-
ary objects directly behind the ve-
hicle, to help avoid damaging the
vehicle.

LHA6507

REARVIEW MONITOR (if so
equipped)

Monitor, climate, audio, phone and voice recognition systems

4-3

•

The distance guide line and the ve-
hicle width line should be used as a
reference only when the vehicle is on
a level paved surface. The distance
viewed on the monitor is for refer-
ence only and may be different than
the actual distance between the ve-
hicle and displayed objects.

CAUTION

Do not scratch the camera lens when
cleaning dirt or snow from the front of
the camera.

The RearView Monitor system automati-
cally shows a rear view of the vehicle when
the shift lever is shifted into the R (Reverse)
position. While in the R (Reverse), pressing
the CAMERA button will cycle through
guideline options. The radio can still be
heard while the RearView Monitor is active.

To display the rear view, the RearView Moni-
tor system uses a camera located just
above the vehicle’s license plate

REARVIEW MONITOR SYSTEM
OPERATION

With the ignition switch in the ON position,
move the shift lever to the R (Reverse) po-
sition to operate the RearView Monitor.

HOW TO READ THE DISPLAYED LINES

Guiding lines which indicate the vehicle
width and distances to objects with refer-
ence to the vehicle body line

are dis-

played on the monitor.

Distance guide lines

Indicate distances from the vehicle body.
• Red line

: approx. 1.5 ft (0.5 m)

• Yellow line

: approx. 3 ft (1 m)

• Green line

: approx. 7 ft (2 m)

Vehicle width guide lines

Indicate the vehicle width when backing up.

LHA3828

LHA4805

4-4

Monitor, climate, audio, phone and voice recognition systems

Predicted course lines

Indicate the predicted course when back-
ing up. The predicted course lines will be
displayed on the monitor when the shift
lever is in the R (Reverse) position and the
steering wheel is turned. The predicted
course lines will move depending on how
much the steering wheel is turned and will
not be displayed while the steering wheel is
in the straight-ahead position.

The vehicle width guide lines and the width
of the predicted course lines are wider than
the actual width and course.

DIFFERENCE BETWEEN PREDICTED
AND ACTUAL DISTANCES

The displayed guidelines and their loca-
tions on the ground are for approximate
reference only. Objects on uphill or downhill
surfaces or projecting objects will be actu-
ally located at distances different from
those displayed in the monitor relative to
the guidelines (refer to illustrations). When
in doubt, turn around and view the objects
as you are backing up, or park and exit the
vehicle to view the positioning of objects
behind the vehicle.

Backing up on a steep uphill

When backing up the vehicle up a hill, the
distance guide lines and the vehicle width
guide lines are shown closer than the ac-
tual distance. Note that any object on the
hill is further than it appears on the
monitor.

Backing up on a steep downhill

When backing up the vehicle down a hill,
the distance guide lines and the vehicle
width guide lines are shown farther than
the actual distance. Note that any object
on the hill is closer than it appears on the
monitor.

LHA5040

LHA5041

Monitor, climate, audio, phone and voice recognition systems

4-5

Backing up near a projecting
object

The predicted course lines

do not touch

the object in the display. However, the ve-
hicle may hit the object if it projects over
the actual backing up course.

Backing up behind a projecting
object

The position

is shown farther than the

position

in the display. However, the po-

sition

is actually at the same distance as

the position

. The vehicle may hit the

object when backing up to the position

if the object projects over the actual back-
ing up course.

HOW TO PARK WITH PREDICTED
COURSE LINES

WARNING

•

If the tires are replaced with different
sized tires, the predicted course lines
may be displayed incorrectly.

•

On a snow-covered or slippery road,
there may be a difference between
the predicted course line and the ac-
tual course line.

•

If the battery is disconnected or be-
comes discharged, the predicted
course lines may be displayed incor-
rectly. If this occurs, please perform
the following procedures:

–

Turn the steering wheel from lock
to lock while the engine is running.

–

Drive the vehicle on a straight road
for more than 5 minutes.

•

When the steering wheel is turned
with the ignition switch in the ACC
position, the predicted course lines
may be displayed incorrectly.

LHA4995

LHA5042

4-6

Monitor, climate, audio, phone and voice recognition systems

1. Visually check that the parking space is

safe before parking your vehicle.

2. The rear view of the vehicle is displayed

on the screen

when the shift lever is

moved to the R (Reverse) position.

3. Slowly back up the vehicle adjusting the

steering wheel so that the predicted
course lines

enter the parking space

4. Maneuver the steering wheel to make

the vehicle width guide lines

parallel

to the parking space

while referring

to the predicted course lines.

5. When the vehicle is parked in the space

completely, move the shift lever to the P
(Park) position and apply the parking
brake.

LHA5043

LHA4770

Monitor, climate, audio, phone and voice recognition systems

4-7

ADJUSTING THE SCREEN

1. While on the main menu screen, press

the CAMERA button.

2. Touch the “Display Settings” key.

3. Touch the “Brightness,” “Contrast,” “Tint,”

“Color,” or “Black Level” key.

4. Adjust the item by touching the “+” or “–”

key on the touch-screen display.

NOTE:
Do not adjust any of the display settings
of the RearView Monitor while the ve-
hicle is moving. Make sure the parking
brake is firmly applied.

HOW TO TURN ON AND OFF
PREDICTED COURSE LINES

To toggle on and off the predicted course
lines while in the P (Park) position:

1. Press the CAMERA button.

2. Touch the “Predicted Course Lines” key

to turn the feature on or off.

To toggle on and off the predicted course
lines while in the R (Reverse) position, press
the CAMERA button.

REARVIEW MONITOR SYSTEM
LIMITATIONS

WARNING

Listed below are the system limitations
for RearView Monitor. Failure to oper-
ate the vehicle in accordance with
these system limitations could result in
serious injury or death.

•

The system cannot completely elimi-
nate blind spots and may not show
every object.

•

Underneath the bumper and the cor-
ner areas of the bumper cannot be
viewed on the RearView Monitor be-
cause of its monitoring range limita-
tion. The system will not show small
objects below the bumper, and may
not show objects close to the bum-
per or on the ground.

•

Objects

viewed

the

RearView

Monitor differ from actual distance
because a wide-angle lens is used.

•

Objects in the RearView Monitor will
appear visually opposite compared
to when viewed in the rearview and
outside mirrors.

•

Use the displayed lines as a refer-
ence. The lines are highly affected by
the number of occupants, fuel level,
vehicle position, road conditions and
road grade.

•

Make sure that the liftgate is securely
closed when backing up.

•

Do not put anything on the rearview
camera. The rearview camera is in-
stalled above the license plate.

LHA5512

4-8

Monitor, climate, audio, phone and voice recognition systems

•

When washing the vehicle with high
pressure water, be sure not to spray it
around the camera. Otherwise, water
may enter the camera unit causing
water condensation on the lens, a
malfunction, fire or an electric shock.

•

Do not strike the camera. It is a preci-
sion instrument. Otherwise, it may
malfunction or cause damage result-
ing in a fire or an electric shock.

The following are operating limitations and
do not represent a system malfunction:
• When the temperature is extremely high

or low, the screen may not clearly display
objects.

• When strong light directly shines on the

camera, objects may not be displayed
clearly.

• Vertical lines may be seen in objects on

the screen. This is due to strong reflected
light from the bumper.

• The screen may flicker under fluorescent

light.

• The colors of objects on the RearView

Monitor may differ somewhat from the
actual color of objects.

• Objects on the monitor may not be clear

in a dark environment.

• There may be a delay when switching

between views.

• If dirt, rain or snow accumulate on the

camera, the RearView Monitor may not
display objects clearly. Clean the camera.

• Do not use wax on the camera lens. Wipe

off any wax with a clean cloth dampened
with a diluted mild cleaning agent, then
wipe with a dry cloth.

SYSTEM MAINTENANCE

CAUTION

•

Do not use alcohol, benzine or thin-
ner to clean the camera. This will
cause discoloration.

•

Do not damage the camera as the moni-
tor screen may be adversely affected.

If dirt, rain or snow accumulates on the
camera

, the RearView Monitor may not

display objects clearly. Clean the camera
by wiping it with a cloth dampened with a
diluted mild cleaning agent and then wip-
ing it with a dry cloth.

LHA3828

Monitor, climate, audio, phone and voice recognition systems

4-9

WARNING

•

Failure to follow the warnings and
instructions for the proper use of
the Intelligent Around View® Monitor
system could result in serious injury
or death.

•

The Intelligent Around View® Monitor
is a convenience feature and is not a
substitute for proper vehicle opera-
tion because it has areas where ob-
jects cannot be viewed. The four cor-
ners of the vehicle in particular, are
areas where objects do not always
appear in the bird’s-eye, front, or rear
views. Always check your surround-
ings to be sure that it is safe to move
before operating the vehicle. Always
operate the vehicle slowly.

•

The driver is always responsible for
safety during parking and other
maneuvers.

CAUTION

Do not scratch the camera lens when
cleaning dirt or snow from the front of
the camera.

The Intelligent Around View® Monitor sys-
tem is designed as an aid to the driver in
situations such as slot parking or parallel
parking.

The monitor displays various views of the
position of the vehicle in a split screen for-
mat. Not all views are available at all times.

Available views:

• Front View

An approximately 150–degree view of the
front of the vehicle.

• Rear View

An approximately 150–degree view of the
rear of the vehicle.

• Bird's-Eye View

The surrounding views of the vehicle
from above.

• Front-Side View

The view around and ahead of the front
passenger's side wheel.

• Full Screen Rear View

The view to the rear of the vehicle (which
is a little wider than the standard Rear
View).

To display the multiple views, the Intelligent
Around View® Monitor system uses cam-
eras located in the front grille, on the vehi-
cle’s outside mirrors and one just above
the vehicle’s license plate

LHA3830

Monitor, climate, audio, phone and voice recognition systems

4-11

INTELLIGENT AROUND VIEW®
MONITOR SYSTEM OPERATION

With the ignition switch in the ON position,
move the shift lever to the R (Reverse) po-
sition to operate the Intelligent Around
View® Monitor.

When the camera is first activated with
the bird’s-eye view in the display, a red icon
(if so equipped) will flash on the screen. This
indicates that the sonar system (if so
equipped) is activated. For additional infor-
mation on the front and rear sonar system
(if so equipped), see “Front and rear sonar
system” (P. 5-125).

The screen displayed on the Intelligent
Around View® Monitor will automatically re-
turn to the previous screen 3 minutes after
the CAMERA button has been pressed with
the shift lever in a position other than the R
(Reverse) position.

Available views

WARNING

•

The distance guide lines and the ve-
hicle width lines should be used as a
reference only when the vehicle is on
a paved, level surface. The apparent
distance viewed on the monitor may
be different than the actual distance
between the vehicle and displayed
objects.

•

Use the displayed lines and the bird’s-
eye view as a reference. The lines and
the bird’s-eye view are greatly af-
fected by the number of occupants,
cargo, fuel level, vehicle position, road
condition and road grade.

•

If the tires are replaced with different
sized tires, the predicted course lines
and the bird's-eye view may be dis-
played incorrectly.

•

When driving the vehicle up a hill, ob-
jects viewed in the monitor are fur-
ther than they appear. When driving
the vehicle down a hill, objects
viewed in the monitor are closer than
they appear.

•

Objects in the rear view will appear
visually opposite compared to when
viewed in the monitor and outside
mirrors.

•

Use the mirrors or actually look to
properly judge distances to other
objects.

•

On a snow-covered or slippery road,
there may be a difference between
the predicted course lines and the
actual course line.

•

The vehicle width and predicted
course lines are wider than the actual
width and course.

•

The

displayed

lines

will

appear

slightly off to the right, because the
rearview camera is not installed in
the rear center of the vehicle.

4-12

Monitor, climate, audio, phone and voice recognition systems

Front and rear view

Guiding lines that indicate the approximate
vehicle width and distance to objects with
reference to the vehicle body line

are

displayed on the monitor.

Distance guide lines:

Indicate distances from the vehicle body:
• Red line

: approximately 1.5 ft (0.5 m)

• Yellow line

: approximately 3 ft (1 m)

• Green line

: approximately 7 ft (2 m)

• Green line

: approximately 10 ft (3 m)

(if so equipped)

Vehicle width guide lines

Indicate the approximate vehicle width
when backing up.

Predicted course lines

Indicate the predicted course when oper-
ating the vehicle. The predicted course
lines will be displayed on the monitor when
the steering wheel is turned. The predicted
course lines will move depending on how
much the steering wheel is turned and will
not be displayed while the steering wheel is
in the straight-ahead position.

The front view will not be displayed when
the vehicle speed is above 6 mph (10 km/h).

NOTE:

When the monitor displays the front
view and the steering wheel turns about
90 degrees or less from the straight-
ahead position, both the right and left
predicted course lines

are displayed.

When the steering wheel turns about 90
degrees or more, a line is displayed only
on the opposite side of the turn.

SAA1840

Front view

LHA4992

Rear view

Monitor, climate, audio, phone and voice recognition systems

4-13

Bird’s-eye view

The bird's-eye view shows the overhead
view of the vehicle, which helps confirm the
vehicle position and the predicted course
to a parking space.

The vehicle icon

shows the position of

the vehicle. Note that the apparent dis-
tance between objects viewed in the
bird's-eye view may differ somewhat from
the actual distance to the vehicle.

The areas that the cameras cannot cover

are indicated in black.

After the ignition switched is placed in the
ON position, the non-viewable area

highlighted in yellow for 3 seconds after the
birds-eye view is displayed.

In addition, the non-viewable corners (if so
equipped) are displayed in red and will blink
for the first 3 seconds

to remind the

driver to be cautious.

WARNING

•

Objects in the bird's-eye view will ap-
pear further than the actual distance.

•

Tall objects, such as a curb or vehicle,
may be misaligned or not displayed
at the seam of the views.

•

Objects that are above the camera
cannot be displayed.

•

The view of the bird's-eye view may
be misaligned when the camera po-
sition alters.

•

A line on the ground may be mis-
aligned and is not seen as being
straight at the seam of the views. The
misalignment will increase as the
line proceeds away from the vehicle.

Front-side view

Guiding lines

Guiding lines that indicate the approximate
width and the front end of the vehicle are
displayed on the monitor.

The front-of-vehicle line

shows the front

part of the vehicle.

The side-of-vehicle line

shows the ap-

proximate vehicle width including the out-
side mirrors.

The extensions

of both the front

and

side

lines are shown with a green dotted

line.

LHA4264

LHA2652

4-14

Monitor, climate, audio, phone and voice recognition systems

DIFFERENCE BETWEEN PREDICTED
AND ACTUAL DISTANCES

Backing up on a steep uphill

Backing up on a steep downhill

LHA5040

LHA5041

Monitor, climate, audio, phone and voice recognition systems

4-15

Backing up near a projecting
object

The predicted course lines

do not touch

the object in the display. However, the ve-
hicle may hit the object if it projects over
the actual backing up course.

Backing up behind a projecting
object

The position

is shown farther than the

position

in the display. However, the po-

sition

is actually at the same distance as

the position

. The vehicle may hit the

object when backing up to the position

if the object projects over the actual back-
ing up course.

HOW TO PARK WITH PREDICTED
COURSE LINES

WARNING

•

If the tires are replaced with different
sized tires, the predicted course lines
may be displayed incorrectly.

•

On a snow-covered or slippery road,
there may be a difference between
the predicted course line and the ac-
tual course line.

•

If the battery is disconnected or be-
comes discharged, the predicted
course lines may be displayed incor-
rectly. If this occurs, please perform
the following procedures:

–

Turn the steering wheel from lock
to lock while the engine is running.

–

Drive the vehicle on a straight road
for more than 5 minutes.

•

When the steering wheel is turned
with the ignition switch in the ACC
position, the predicted course lines
may be displayed incorrectly.

LHA4995

LHA5042

4-16

Monitor, climate, audio, phone and voice recognition systems

1. Visually check that the parking space is

safe before parking your vehicle.

2. The rear view of the vehicle is displayed

on the screen

when the shift lever is

moved to the R (Reverse) position.

3. Slowly back up the vehicle adjusting the

steering wheel so that the predicted
course lines

enter the parking space

4. Maneuver the steering wheel to make

the vehicle width guide lines

parallel

to the parking space

while referring

to the predicted course lines.

5. When the vehicle is parked in the space

completely, move the shift lever to the P
(Park) position and apply the parking
brake.

HOW TO SWITCH THE DISPLAY

With the ignition switch in the ON position,
press the CAMERA button or move the shift
lever to the R (Reverse) position to operate
the Intelligent Around View® Monitor.

The Intelligent Around View® Monitor dis-
plays different split screen views depend-
ing on the position of the shift lever. Press
the CAMERA button to switch between the
available views.

If the shift lever is in the R (Reverse) position,
the available views are:
• Rear view/bird’s-eye view split screen
• Rear view/front-side view split screen
• Full screen rear view

If the shift lever is in the P (Park) or D (Drive)
position, the available views are:
• Front view/bird’s-eye view split screen
• Front view/front-side view split screen

LHA5043

LHA4770

Monitor, climate, audio, phone and voice recognition systems

4-17

The display will switch from the Intelligent
Around View® Monitor screen when:
• The shift lever is in the D (Drive) position

and the vehicle speed increases above
approximately 6 mph (10 km/h)

• A different screen is selected.

ADJUSTING THE SCREEN

1. Press the MENU button.

2. Touch the “Settings” key.

3. Touch the “

” key to move to the next

page.

4. Touch the “Camera” key.

5. Touch “Display settings” key.

6. Touch the “Brightness,” “Contrast,” “Tint,”

“Color,” or “Black Level” key.

7. Adjust the item by touching the “+” or “-”

key on the touch-screen display or by
turning the Tune-Scroll knob.

NOTE:

Do not adjust any of the display settings
of the Intelligent Around View® Monitor
while the vehicle is moving. Make sure
the parking brake is firmly applied.

LHA5512

4-18

Monitor, climate, audio, phone and voice recognition systems

INTELLIGENT AROUND VIEW®
MONITOR SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for Intelligent Around View® Monitor.
Failure to operate the vehicle in accor-
dance with these system limitations
could result in serious injury or death.

•

Do not use the Intelligent Around
View® Monitor with the outside mir-
rors in the stored position, and make
sure that the liftgate is securely
closed when operating the vehicle
using the Intelligent Around View®
Monitor.

•

The apparent distance between ob-
jects

viewed

the

Intelligent

Around View® Monitor differs from
the actual distance.

•

The cameras are installed on the
front grille, the outside mirrors and
above the rear license plate. Do not
put anything on the vehicle that cov-
ers the cameras.

•

When washing the vehicle with high
pressure water, be sure not to spray it
around the cameras. Otherwise, wa-
ter may enter the camera unit caus-
ing water condensation on the lens, a
malfunction, fire or an electric shock.

•

Do not strike the cameras. They are
precision

instruments.

Doing

could cause a malfunction or cause
damage resulting in a fire or an elec-
tric shock.

There are some areas where the system
will not show objects and the system does
not warn of moving objects. When in the
front or rear view display, an object below
the bumper or on the ground may not be
viewed

. When in the bird’s-eye view, a tall

object near the seam

of the camera

viewing areas will not appear in the
monitor.

The following are operating limitations and
do not represent a system malfunction:
• There may be a delay when switching

between views.

• When the temperature is extremely high

or low, the screen may not display objects
clearly.

• When strong light directly shines on the

camera, objects may not be displayed
clearly.

• The screen may flicker under fluorescent

light.

• The colors of objects on the Intelligent

Around View® Monitor may differ some-
what from the actual color of objects.

LHA3831

Monitor, climate, audio, phone and voice recognition systems

4-19

• Objects on the Intelligent Around View®

Monitor may not be clear and the color
of the object may differ in a dark
environment.

• There may be differences in sharpness

between each camera view of the bird's-
eye view.

• Do not use wax on the camera lens. Wipe

off any wax with a clean cloth that has
been dampened with a diluted mild clean-
ing agent, then wipe with a dry cloth.

System temporarily unavailable

When the “!” icon is displayed on the screen,
there are abnormal conditions in the Intel-
ligent Around View® Monitor. This will not
hinder normal driving operation but the
system should be inspected. It is recom-
mended that you visit a NISSAN dealer for
this service.

When the “[X]” icon is displayed on the
screen, the camera image may be receiv-
ing temporary electronic disturbances
from surrounding devices. This will not hin-
der normal driving operation but the sys-
tem should be inspected if it occurs fre-
quently. It is recommended that you visit a
NISSAN dealer for this service.

LHA3591

LHA3592

4-20

Monitor, climate, audio, phone and voice recognition systems

SYSTEM MAINTENANCE

CAUTION

•

Do not use alcohol, benzine or thin-
ner to clean the camera. This will
cause discoloration.

•

Do not damage the cameras as the
monitor screen may be adversely
affected.

If dirt, rain or snow accumulates on any of
the cameras

, the Intelligent Around

View® Monitor may not display objects
clearly. Clean the camera by wiping with a
cloth dampened with a diluted mild clean-
ing agent and then wiping with a dry cloth.

LHA5038

Monitor, climate, audio, phone and voice recognition systems

4-21

WARNING

•

Failure to follow the warnings and in-
structions for proper use of the Mov-
ing Object Detection (MOD) system
could result in serious injury or death.

•

The MOD system is not a substitute
for proper vehicle operation and is
not designed to prevent contact with
objects

surrounding

the

vehicle.

When maneuvering, always use the
outside mirrors and rearview mirror
and turn and check the surroundings
to ensure it is safe to maneuver.

•

The system is deactivated at speeds
above 6 mph (10 km/h). It is reacti-
vated at lower speeds.

•

The MOD system is not designed to
detect

surrounding

stationary

objects.

The MOD system can inform the driver of
moving objects near the vehicle when
backing out of garages, maneuvering in
parking lots and in other such instances.

The MOD system detects moving objects
by using image processing technology on
the image shown in the display.

MOD SYSTEM OPERATION

The MOD system will turn on automatically
under the following conditions:
• When the shift lever is in the R (Reverse)

position.

• When vehicle speed decreases below ap-

proximately 6 mph (10 km/h) and the
camera screen is displayed.

The MOD system operates in the following
conditions when the camera view is
displayed:
• When the shift lever is in the P (Park) or N

(Neutral) position and the vehicle is
stopped, the MOD system detects mov-
ing objects in the bird’s-eye view. The
MOD system will not operate if the out-
side mirrors are moving in or out, in the
stowed position, or if either front door is
opened.

LHA4190

Front and bird’s-eye views

Monitor, climate, audio, phone and voice recognition systems

4-23

• When the shift lever is in the D (Drive)

position and the vehicle speed is below
approximately 6 mph (10 km/h), the MOD
system detects moving objects in the
front view.

• When the shift lever is in the R (Reverse)

position and the vehicle speed is below
approximately 6 mph (10 km/h), the MOD
system detects moving objects in the
rear view. The MOD system will not oper-
ate if the liftgate is open.

The MOD system does not detect moving
objects in the front-side view. The MOD
icon is not displayed on the screen when in
this view.

When the MOD system detects moving ob-
jects near the vehicle, a chime will be heard
and a yellow frame will be displayed on the
view where the objects are detected. While
the MOD system continues to detect mov-
ing objects, the yellow frame continues to
be displayed.

NOTE:

While the Rear Cross Traffic Alert chime
(if so equipped) is beeping, the MOD sys-
tem does not chime

In the bird’s-eye view, the yellow frame

displayed on each camera image (front,
rear, right, left) depending on where mov-
ing objects are detected.

The yellow frame

is displayed on each

view in the front view and rear view modes.

LHA5171

Rear and bird’s-eye views

LHA4997

Rear and front-side views

LHA4998

Full screen rear view

4-24

Monitor, climate, audio, phone and voice recognition systems

A blue MOD icon

is displayed in the view

where the MOD system is operative. A gray
MOD icon is displayed in the view where the
MOD system is not operative.

If the MOD system is turned off, the MOD
icon

is not displayed.

TURNING MOD ON AND OFF

To turn the MOD system on or off, press and
hold the CAMERA button for more than 2
seconds.

MOD SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for MOD. Failure to operate the vehicle
in accordance with these system limi-
tations could result in serious injury or
death.

•

Do not use the MOD system when
towing a trailer. The system may not
function properly.

•

Excessive noise (for example, audio
system volume or open vehicle win-
dow) will interfere with the chime
sound, and it may not be heard.

•

The MOD system performance will be
limited according to environmental
conditions and surrounding objects
such as:

–

When there is low contrast be-

tween background and the mov-
ing objects.

–

When there is a blinking source of

light.

–

When strong light such as another

vehicle’s headlight or sunlight is
present.

–

When camera orientation is not in

its usual position, such as when a
mirror is folded.

–

When there is dirt, water drops or

snow on the camera lens.

–

When the position of the moving

objects in the display is not
changed.

•

The MOD system might detect flow-
ing water droplets on the camera
lens, white smoke from the muffler,
moving shadows, etc.

•

The MOD system may not function
properly depending on the speed, di-
rection, distance or shape of the
moving objects.

•

If your vehicle sustains damage to
the parts where the camera is in-
stalled, leaving it misaligned or bent,
the sensing zone may be altered and
the MOD system may not detect ob-
jects properly.

•

When the temperature is extremely
high or low, the screen may not dis-
play objects clearly. This is not a
malfunction.

NOTE:
The blue MOD icon will change to or-
ange if one of the following has oc-
curred:

•

When the system is malfunctioning.

•

When the component temperature
reaches a high level (icon will blink).

•

When the rearview camera has de-
tected a blockage (icon will blink).

If the icon light continues to illuminate
orange, have the MOD system checked. It
is recommended that you visit a NISSAN
dealer for this service.

Monitor, climate, audio, phone and voice recognition systems

4-25

Nissan Murano (2024 year). Manual in english - page 7