Nissan Murano (2024 year). Manual in english

3. Adjust the desired amount of air using

the control knob. The climate controlled
seat blower remains on low speed for
approximately 60 seconds after turning
the switch on or selecting the desired
temperature.

4. When the vehicle's interior is warmed or

cooled, or before you leave the vehicle,
be sure to turn the control knob to the
off (center) position. The indicator light

on the control knob goes off with the

switch in the off (center) position.

To check the air filter for the climate con-
trolled seat, it is recommended that you
visit a NISSAN dealer.

WARNING

Do not use or allow occupants to use
the climate controlled seats if you or
the occupants cannot monitor seat
temperatures or have an inability to
feel pain in those body parts in contact
with the seat. Use of the climate con-
trolled seats by such people could re-
sult in serious injury.

CAUTION

•

The battery could run down if the cli-
mate control seat is operated while
the engine is not running.

•

Do not use the climate control seat
for extended periods or when no one
is using the seat.

•

Do not put anything on the seat
which insulates heat, such as a blan-
ket, cushion, seat cover, etc. Other-
wise, the seat may become over-
heated.

•

Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar objects. This may result in
damage to the climate controlled seat.

•

Any liquid spilled on the seat should
be removed immediately with a dry
cloth.

•

The climate controlled seat has an air
filter. Do not operate the climate con-
trolled seat without an air filter. This
may result in damage to the system.

•

When cleaning the seat, never use
gasoline, benzine, thinner, or any
similar materials.

•

If any malfunctions are found or the
climate controlled seat does not op-
erate, turn the switch off and have
the system checked. It is recom-
mended that you visit a NISSAN
dealer for this service.

2-48

Instruments and controls

WARNING

Do not use or allow occupants to use
the seat heater if you or the occupants
cannot monitor elevated seat tem-
peratures or have an inability to feel
pain in those body parts in contact with
the seat. Use of the seat heater by such
people could result in serious injury.

CAUTION

•

The battery could run down if the
seat heater is operated while the en-
gine is not running.

•

Do not use the seat heater for ex-
tended periods or when no one is us-
ing the seat.

•

Do not put anything on the seat
which insulates heat, such as a blan-
ket, cushion, seat cover, etc. Other-
wise, the seat may become over-
heated.

•

Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the heater.

•

Any liquid spilled on the heated seat
should be removed immediately with
a dry cloth.

•

When cleaning the seat, never use
gasoline, benzine, thinner, or any
similar materials.

•

If any malfunctions are found or the
heated seat does not operate, turn
the switch off and have the system
checked. It is recommended that you
visit a NISSAN dealer for this service.

The front seats are warmed by built-in
heaters.

1. Start the engine.

2. Push the LO or HI position of the switch,

as desired. The indicator light in the
switch will illuminate.

The heater is controlled by a thermostat,
automatically turning the heater on and
off. The indicator light will remain on as
long as the switch is on.

3. When the seat is warmed or before you

leave the vehicle, be sure to push the
switch to turn it off.

LIC3475

HEATED SEAT SWITCHES (if so
equipped)

Instruments and controls

2-49

WARNING

Do not use or allow occupants to use
the seat heater if you or the occupants
cannot monitor elevated seat tem-
peratures or have an inability to feel
pain in body parts that contact the
seat. Use of the seat heater by such
people could result in serious injury.

CAUTION

•

The battery could run down if the
seat heater is operated while the en-
gine is not running.

•

Do not use the seat heater for ex-
tended periods or when no one is us-
ing the seat.

•

Do not put anything on the seat
which insulates heat, such as a blan-
ket, cushion, seat cover, etc. Other-
wise, the seat may become over-
heated.

•

Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the heater.

•

Any liquid spilled on the heated seat
should be removed immediately with
a dry cloth.

•

When cleaning the seat, never use
gasoline, benzine, thinner, or any
similar materials.

•

If any malfunctions are found or the
heated seat does not operate, turn
the switch off and have the system
checked. It is recommended that you
visit a NISSAN dealer for this service.

The rear seats are warmed by built-in heat-
ers. The switches are located on the rear of
the front center console and can be oper-
ated independently of each other.

1. Place the ignition switch in the ON

position.

2. Push the LO or HI position of the switch,

as desired. The indicator light in the
switch will illuminate.

The heater is controlled by a thermostat,
automatically turning the heater on and
off. The indicator light will remain on as
long as the switch is on.

LIC3475

HEATED REAR SEAT SWITCHES (if so
equipped)

2-50

Instruments and controls

3. When the seat is warmed or before you

leave the vehicle, be sure to turn the
switch off.

The heated steering wheel system is de-
signed to operate only when the surface
temperature of the steering wheel is below
68°F (20°C).

Push the heated steering wheel switch to
warm the steering wheel after the ignition
switch is placed in the ON position. The
indicator light will come on.

If the surface temperature of the steering
wheel is below 68°F (20°C), the system will
heat the steering wheel and cycle off and
on to maintain a temperature above 68°F
(20°C). The indicator light will remain on as
long as the system is on.

Push the switch again to turn the heated
steering wheel system off manually. The
indicator light will go off.

NOTE:
• Once activated, your heated steering

wheel will automatically turn on and
off to maintain a temperature above
68°F (20°C).

• When the temperature of the steering

wheel is above 122°F (50°C) and the
heated steering wheel switch is turned
on, the system will not heat the steer-
ing wheel. This does not indicate a
malfunction.

LIC2221

HEATED STEERING WHEEL SWITCH (if
so equipped)

Instruments and controls

2-51

The dynamic driver assistance switch is
used to temporarily activate the Intelligent
Lane Intervention (I-LI) system that is en-
abled using the settings menu of the ve-
hicle information display.

The I-LI system can be turned on with the
dynamic driver assistance switch after
starting the engine.

The dynamic driver assistance switch illu-
minates for a few seconds when the igni-
tion switch is placed in the ON position.

When

the

dynamic

driver

assistance

switch is turned off, the indicator

on the

switch is off. The indicator will also be off if
the I-LI system is deactivated using the ve-
hicle information display.

The I-LI system warns the driver with an
indicator and a steering wheel vibration,
and helps assist the driver to return the
vehicle to the center of the traveling lane by
applying the brakes to the left or right
wheels individually (for a short period of
time). For additional information, see “Intel-
ligent Lane Intervention (I-LI)” (P. 5-32) and
“Vehicle information display” (P. 2-18).

The vehicle should be driven with the VDC
system on for most driving conditions.

If the vehicle is stuck in mud or snow, the
VDC system reduces the engine output to
reduce wheel spin. The engine speed will
be reduced even if the accelerator is de-
pressed to the floor. If maximum engine
power is needed to free a stuck vehicle,
turn the VDC system off.

To turn off the VDC system, push the VDC
OFF switch. The

indicator light will

come on.

LIC3681

LIC3344

DYNAMIC DRIVER ASSISTANCE
SWITCH

VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH

2-52

Instruments and controls

Push the VDC OFF switch again or restart
the engine to turn on the system. For addi-
tional information, see “Vehicle Dynamic
Control (VDC) system” (P. 5-122).

When the VDC OFF switch is used to turn off
the VDC system, the Automatic Emergency
Braking (AEB) with Pedestrian Detection
and Rear Automatic Braking (RAB) systems
are also turned off. For additional informa-
tion, see “Automatic Emergency Braking
(AEB) with Pedestrian Detection”(P. 5-86)
and “Rear Automatic Braking (RAB)” (P. 5-81).

EMERGENCY SUPPORT

NissanConnect® Services provide various
services to support dealing with emergen-
cies of the subscribed vehicle and the
driver.

For example, in case of an illness or serious
injury, you can seek support by pressing
the in-vehicle Emergency Call (SOS) button
and connecting to the NissanConnect® Ser-
vices Response Center. The NissanConnect®
Services Response Center can specify the
location of the vehicle via GPS, and the infor-
mation will be sent to the police or other
agencies as needed.

For information about other NissanConnect®
Services emergency support related ser-
vices, contact the NissanConnect® Customer
Support line at 1–855–426–6628 or refer
to the NissanConnect® Services website
www.nissanusa.com/connect (for U.S.) or
www.nissan.ca/nissanconnect

(English)

www.nissan.ca/nissanconnect/fr (French) (for
Canada).

WARNING

•

Please note that the Automatic Colli-
sion Notification service and Emer-
gency Call function cannot be used in
the following conditions:

–

Emergency functions and services
will not be available without a paid
subscription

NissanConnect®

Services.

–

The NissanConnect® Services net-
work system is disabled.

–

The vehicle moves outside the ser-
vice area where the TCU (Telematics
Control Unit) is connected to the
system.

–

The vehicle is outside the area
where the cellular network service
is receivable.

–

The vehicle is in a location with
poor signal reception such as
tunnels,

underground

parking

garages, behind buildings or in
mountainous areas.

–

The line is busy.

–

The TCU (Telematics Control Unit)
or other systems of your vehicle
are not working properly.

EMERGENCY CALL (SOS) BUTTON
(if so equipped)

Instruments and controls

2-53

–

It may not be possible to make an
emergency call depending on the
severity of a collision and/or
emergency.

•

Park the vehicle in a safe location and
set the parking brake before operat-
ing the Emergency Call (SOS) button.

•

Only use this service in case of an
emergency. There may be a penalty
for inappropriate use of the service.

•

Radio waves could adversely affect
electric medical equipment. Indi-
viduals who use a pacemaker should
contact the device manufacturer re-
garding any possible effects before
using the system.

•

The TCU (Telematics Control Unit) an-
tenna is installed inside the upper
central part of the instrument panel.
An occupant should not get any
closer to the antenna than specified
by the pacemaker manufacturer. The
radio waves from the TCU antenna
may adversely affect the operation
of the pacemaker while using the
NissanConnect® Services.

Making an emergency call

The Emergency Call (SOS) button is located
near the map light.

1. Press the Emergency Call (SOS) button

to make an emergency call.

2. When the line is connected, speak to the

Response Specialist.

If you want to cancel the emergency call,
press and hold the Emergency Call (SOS)
button for a few seconds.

NOTE:

•

After the Emergency Call (SOS) button
is pressed, it may take some time until
the system initiates connection, de-
pending on the technical environment
and whether the TCU (Telematics Con-
trol Unit) is being used by the other
services.

•

An indicator light on the Emergency
call (SOS) button shows the readiness
of the emergency support system. If
the indicator light is not illuminated,
pressing the Emergency Call (SOS)
button does not connect your vehicle
to the Response Specialist. The indica-
tor light blinks while connected to
the NissanConnect® Services Response
Center.

•

Even when the indicator light is illumi-
nated, connection to the NissanConnect®
Services Response Center may not be
possible. If this occurs in an emergency
situation, contact the authorities by other
means.

•

To avoid disconnecting the line, keep
the engine running during an emer-
gency call, if it is safe to do so.

LIC3357

2-54

Instruments and controls

1. Type-C USB

2. Type-A USB

There are USB/iPod® charging ports lo-
cated in the rear seat area on the back of
the center console. These ports will charge
compatible devices.

NOTE:
• Only the USB connection port(s) lo-

cated below the instrument panel will
allow operation of USB/iPod® devices
through the audio system.

• For best results, it is recommended to

use the manufacturer cables, which
are sold separately. A USB Type-A to
USB Type-C adapter (or vice versa) can
also be purchased separately; how-
ever, results may vary.

The Rear Door Alert system functions un-
der certain conditions to indicate there
may be an object or passenger in the rear
seat(s). Check the seat(s) before exiting the
vehicle.

The Rear Door Alert system is initially dis-
abled. The driver can enable the system
using the vehicle information display. For
additional information, see “Vehicle infor-
mation display warnings and indicators”
(P. 2-29).

When the system is enabled:
• The system is activated when a rear door

is opened and closed within 10 minutes of
the vehicle being driven. When the driver
door is closed and the system is acti-
vated, a visual message appears in the
vehicle information display. For additional
information, see “Rear Door Alert is acti-
vated” (P. 2-30).

• If a rear door is opened and closed but

the vehicle is not driven within approxi-
mately 10 minutes, the system will not be
activated. A rear door must be opened
and closed and the car driven within 10
minutes for the system to activate.

LIC5051

Rear seat area

USB/iPod® CHARGING PORTS

REAR DOOR ALERT

Instruments and controls

2-55

When the Rear Door Alert system is acti-
vated:
• When the driver puts the vehicle in the P

(Park) position, a notification message
appears in the vehicle information dis-
play with the options to “Dismiss Mes-
sage” or “Disable Alert” if desired.

• Select “Disable Alert” to temporarily

disable for that stop.

• No selection or ‘Dismiss Message” will

keep the alert enabled for that stop.

• If the alert is enabled when a driver exits

the vehicle, a message will appear in the
vehicle information display that states
“Check Rear Seat for All Articles.”

If “Horn & Alert” setting is selected:

• An audible horn sound will occur after

a short time unless a rear door is
opened and closed within a short time
to deactivate the alert.

• If the doors are locked before the alert

is deactivated by opening a rear door,
the horn will sound.

• If the liftgate is opened before a rear

door is opened, the horn will be de-
layed until after the liftgate is closed.

NOTE:

If “Alert Only” setting is selected, the
message alert will still be shown in the
vehicle information display but the horn
will not sound.

WARNING

•

If the driver selects “Disable Alert”, no
audible alert will be provided regard-
less of rear door open/close status.

•

There may be times when there is
an object or passenger in the rear
seat(s) but the audible alert does not
sound. For example, this may occur if
rear seat passengers enter or exit the
vehicle during a trip.

•

The system does not directly detect
objects or passengers in the rear
seat(s). Instead, it can detect when a
rear door is opened and closed, indi-
cating that there may be something
in the rear seat(s).

NOTE:

There may be times when the horn
sounds but there are no objects or pas-
sengers in the rear seat(s).

For additional information, see “Rear Door
Alert is activated” (P. 2-30).

2-56

Instruments and controls

12V OUTLETS

The power outlets are for powering electri-
cal accessories such as cellular tele-
phones. They are rated at 12 volt, 120W (10A)
maximum.

The vehicle’s power outlets are powered
only when the ignition switch is in the ACC
or ON position.

Open the cap to use a power outlet.

CAUTION

•

The outlet and plug may be hot dur-
ing or immediately after use.

•

Only certain power outlets are de-
signed for use with a cigarette lighter
unit. Do not use any other power out-
let for an accessory lighter. It is rec-
ommended that you visit a NISSAN
dealer for additional information.

•

Do not use with accessories that ex-
ceed a 12 volt, 120W (10A) power draw.

•

Do not use double adapters or more
than one electrical accessory.

•

Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.

•

Avoid using power outlets when the
air conditioner, headlights or rear
window defroster is on.

•

Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned off.

•

Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.

•

When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.

LIC4598

Instrument Panel

LIC3199

Cargo Area

POWER OUTLETS

Instruments and controls

2-57

The extended storage switch is pulled out
when in transit from the factory to the re-
tailer. It is located in the fuse panel to the
left of the steering wheel on the instrument
panel. If any electrical equipment does not
operate, ensure the extended storage
switch is pushed fully in place, as shown.

LIC4599

LIC3266

Pulled position

LIC3268

Pushed position

EXTENDED STORAGE SWITCH

2-58

Instruments and controls

WARNING

To ensure proper operation of the driv-
er’s and/or front passenger’s NISSAN
Advanced

Air

Bag

System

(if

equipped), please observe the follow-
ing items:

•

Do not allow a passenger in the rear
seat to push or pull on the seatback
pocket or head restraint/headrest.

•

Do not place heavy loads heavier
than 9.1 lbs. (4 kg) on the seatback,
head restraint/headrest or in the
seatback pocket.

STORAGE TRAYS

WARNING

Do not place sharp objects in the trays
to help prevent injury in an accident or
sudden stop.

LIC3854

Front console

LIC2214

Rear armrest

2-60

Instruments and controls

GLOVE BOX

Open the glove box by pulling the handle.

Use the mechanical key to lock or unlock
the glove box. The valet key (if so equipped)
cannot be used to lock or unlock the glove
box.

WARNING

Keep glove box lid closed while driving
to help prevent injury in an accident or
a sudden stop.

CONSOLE BOX

To open the console box, press in on the
lever and raise the lid.

To close, push the lid down until the lock
latches.

LIC3202

Rear center console

LIC3003

LIC3991

Instruments and controls

2-61

OVERHEAD SUNGLASSES
STORAGE

To open the sunglasses holder, push and
release.

Only store one pair of sunglasses in the
holder.

WARNING

Keep the sunglasses holder closed
while driving to avoid obstructing the
driver’s view and to help prevent an
accident.

CAUTION

•

Do not use for anything other than
sunglasses.

•

Do not leave sunglasses in the sun-
glasses holder while parking in direct
sunlight. The heat may damage the
sunglasses.

CUP HOLDERS

CAUTION

•

Avoid abrupt starting and braking
when the cup holder is being used to
prevent spilling the drink. If the liquid
is hot, it can scald you or your
passenger.

•

Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.

LIC2312

LIC3854

Front console

2-62

Instruments and controls

•

Do not recline the rear seatback
when you use the cup holders on the
rear armrest. Doing so may cause the
beverages to spill over, and if they are
hot, they may scald the passengers.

CAUTION

•

Do not use the bottle holder for any
other objects that could be thrown
about in the vehicle and possibly in-
jure people during sudden braking or
an accident.

•

Do not use the bottle holder for open
liquid containers.

LIC2915

Bench seat

LIC3672

Bottle holder — front

Instruments and controls

2-63

CARGO AREA STORAGE BIN

To access the floor storage area, pull up on
the left and right side of the cargo floor.

LUGGAGE HOOKS

When securing items using luggage hooks
located on the side finisher do not apply a
load over more than 6.5 lbs. (29 N) to a
single hook.

The luggage hooks that are located on the
floor should have loads less than 110 lbs.
(490 N) to a single hook.

The luggage hooks can be used to secure
cargo with ropes or other types of straps.

LIC2933

Bottle holder — rear

LIC3204

LTI2113

2-64

Instruments and controls

WARNING

•

Properly secure all cargo with ropes
or straps to help prevent it from slid-
ing or shifting. Do not place cargo
higher than the seatbacks. In a sud-
den stop or collision, unsecured
cargo could cause personal injury.

•

Use suitable ropes and hooks to se-
cure cargo.

•

Never allow anyone to ride in the lug-
gage area. It is extremely dangerous
to ride in a cargo area inside of a ve-
hicle. In a collision, people riding in
these areas are more likely to be se-
riously injured or killed.

•

Do not allow people to ride in any
area of your vehicle that is not
equipped with seats and seat belts.

•

The child restraint top tether strap
may be damaged by contact with
items in the cargo area. Secure any
items in the cargo area. Your child
could be seriously injured or killed in
a collision if the top tether strap is
damaged.

•

Be sure everyone in your vehicle is in
a seat and using a seat belt properly.

COAT HOOKS

The coat hooks, located on the rear assist
grips, may be used to store coats and other
articles of clothing.

CAUTION

Do not apply more than 33 lbs. (15 kg) to
the rear assist grip coat hook.

ROOF RACK (if so equipped)

WARNING

•

Always install the crossbars onto the
roof side rails before loading cargo of
any kind. Loading cargo directly onto
the roof side rails or the vehicle’s roof
may cause vehicle damage.

•

Roof rack cross bars should be evenly
distributed.

•

Do not exceed maximum roof rack
crossbars load capacity and always
distribute the load uniformly.

LIC4173

LIC4202

Instruments and controls

2-65

•

Heavy loading of the crossbars has
the potential to affect the vehicle
stability and handling during sudden
or unusual handling maneuvers.

•

Properly secure all cargo with ropes
or straps to help prevent it from slid-
ing or shifting. In a sudden stop or
collision,

unsecured

cargo

could

cause personal injury.

•

Drive extra carefully when the vehicle
is loaded at or near the cargo carry-
ing capacity, especially if the signifi-
cant portion of that load is carried on
the crossbars.

CAUTION

•

Use care when placing or removing
items from the roof rack. If you can-
not comfortably lift the items onto
the roof rack from the ground, use a
ladder or a stool.

Do not apply any load directly to the roof
side rails

. Crossbars

must be in-

stalled

before

applying

load/cargo/

luggage to the roof of the vehicle.

Genuine NISSAN accessory crossbars may
be available through a NISSAN dealer. It is
recommended that you visit a NISSAN
dealer for additional information.

The service load capacity for the roof side
rails is 220 lbs. (100 kg.), however do not
exceed the crossbars load capacity.

Be careful that your vehicle does not ex-
ceed the Gross Vehicle Weight Rating
(GVWR) or its Gross Axle Weight Rating
(GAWR front and rear).

For additional information regarding GVWR
and GAWR, refer to:
• F.M.V.S.S. or C.M.V.S.S. certification label (lo-

cated on the driver’s door pillar).

Installing crossbars (if so
equipped)

WARNING

•

It is recommended that you have the
roof rack crossbars installed by a
NISSAN dealer.

•

Protect the painted area on the vehi-
cle’s roof under the crossbars by plac-
ing a piece of cloth under the cross
bars to prevent scratch damage.

•

Make

sure

the

moonroof

(if

equipped) is in the closed position
during the installation process.

2-66

Instruments and controls

POWER WINDOWS

WARNING

•

Make sure that all passengers have
their hands, etc., inside the vehicle
while it is in motion and before clos-
ing the windows. Use the window
lock switch to prevent unexpected
use of the power windows.

•

To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not
leave children, people who require
the assistance of others or pets unat-
tended in your vehicle. Additionally,
the temperature inside a closed ve-
hicle on a warm day can quickly be-
come high enough to cause a signifi-
cant risk of injury or death to people
and pets.

The power windows operate when the ig-
nition switch is placed in the ON position or
for a period of time after the ignition switch
is placed in the OFF position. If the driver's
or passenger's door is opened during this
period of time, the power to the windows is
canceled.

Driver's side power window
switch

The driver's side control panel is equipped
with switches to open or close all of the
windows.

To open a window, push the switch to the
detent and continue to hold down until the
desired window position is reached. To
close a window, pull the switch to the de-
tent and continue to hold up until the de-
sired window position is reached.

Locking passengers' windows

When the window lock switch is pushed,
only the driver's side window can be
opened or closed. Push it again to cancel
the window lock function.

LIC3238

1. Window lock button

2. Power door lock switch

3. Front passenger side automatic switch

4. Right rear passenger side switch

5. Left rear passenger side switch

6. Driver’s side automatic switch

WINDOWS

Instruments and controls

2-67

Front passenger's power window
switch

The passenger's window switch operates
only the corresponding passenger's win-
dow. To open the window partially, push the
switch down lightly until the desired win-
dow position is reached. To close the win-
dow partially, pull the switch up until the
desired window position is reached.

Rear power window switch

The rear power window switches open or
close only the corresponding windows. To
open the window, push the switch and hold
it down

. To close the window, pull the

switch up

Automatic operation

To fully open a window, push the window
switch down to the second detent and re-
lease it; it need not be held. The window
automatically opens all the way. To stop
the window, lift the switch up while the win-
dow is opening.

To fully close a window, pull the switch up to
the second detent and release it; it need
not be held. To stop the window, push the
switch down while the window is closing.

LIC2397

LIC2663

LIC0410

2-68

Instruments and controls

Auto-reverse function (if so
equipped)

The auto-reverse function can be acti-
vated when a window is closed by auto-
matic operation.

Depending on the environment or driv-
ing conditions, the auto-reverse func-
tion may be activated if an impact or
load similar to something being caught
in the window occurs.

WARNING

There are some small distances immedi-
ately before the closed position which
cannot be detected. Make sure that all
passengers have their hands, etc., inside
the vehicle before closing the window.

If the vehicle's battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate prop-
erly. Have the power window auto-reverse
system re-initialized. It is recommended that
you visit a NISSAN dealer for this service.

If the control unit detects something
caught in a window equipped with auto-
matic operation as it is closing, the window
will be immediately lowered.

The moonroof will only operate when the
ignition switch is placed in the ON position.
The moonroof is operational for a period of
time, even if the ignition switch is placed in
the ACC (if so equipped) or OFF position. If
the driver's door or the front passenger's
door is opened during this period of time,
the power to the moonroof is canceled.

When operating the power moonroof or
panoramic sunshade, the switch need not
be held continuously. To stop the moon-
roof or sunshade at any point while it is
opening

closing, push

the

switch

momentarily.

Sliding the moonroof

To open the moonroof, push the switch to
the open

position and release it; it need

not be held. The roof will automatically
open or close all the way.

Push the switch again to fully open the
moonroof.

To close the moonroof, push the switch to
the

position and release it. The roof will

automatically close all the way.

To stop the moonroof, push the switch
once more while it is opening or closing.

Tilting the moonroof

To tilt the moonroof up, first close the
moonroof. Push the switch to the

posi-

tion and release it; it need not be held.

To tilt down the moonroof, push the switch
to the

position and release it.

LIC4148

POWER MOONROOF (if so equipped)

Instruments and controls

2-69

Auto-reverse function (when
closing or tilting down the
moonroof)

The auto-reverse function can be acti-
vated when the moonroof is closed or
tilted down by automatic operation when
the ignition switch is placed in the ON po-
sition or for a period of time after the igni-
tion switch is placed in the OFF position.

Depending on the environment or driv-
ing conditions, the auto-reverse func-
tion may be activated if an impact or
load similar to something being caught
in the moonroof occurs.

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the moonroof.

When closing

If the control unit detects something
caught in the moonroof as it moves to the
front, the moonroof will immediately open
backward.

When tilting down

If the control unit detects something
caught in the moonroof as it tilts down, the
moonroof will immediately tilt up.

If the auto-reverse function malfunctions
and repeats opening or tilting up the moon-
roof, keep pushing the tilt down switch within
5 seconds after it happens; the moonroof
will fully close gradually. Make sure nothing is
caught in the moonroof.

WARNING

•

In an accident you could be thrown
from the vehicle through an open
moonroof. Always use seat belts and
child restraints.

•

Do not allow anyone to stand up or
extend any portion of their body out
of the moonroof opening while the
vehicle is in motion or while the
moonroof is closing.

CAUTION

•

Remove water drops, snow, ice or
sand from the moonroof before
opening.

•

Do not place heavy objects on the
moonroof or surrounding area.

2-70

Instruments and controls

Panoramic sunshade

The panoramic sunshade operates when
the ignition switch is in the ON position. The
sunshade switch is located near the roof
console. When opening or closing the sun-
shade the switch need not be held.

To open the sunshade:
• To fully open the sunshade, push the

switch toward the open position

To close the sunshade:
• To fully close the sunshade, push the

switch toward the close position

WARNING

•

To avoid personal injury, keep your
hands, fingers and head away from
the sunshade arm, the arm rail and
sunshade inlet port.

•

Do not allow children near the rear
sunshade system. They could be
injured.

•

Do not place objects on or near the
rear sunshade. This could cause im-
proper operation or damage it.

•

Do not pull or push the rear sun-
shade. This could cause improper op-
eration or damage it.

CAUTION

•

Do not place objects (such as news-
papers, handkerchiefs, etc.) on the
sunshade inlet port. Doing so may
entangle these objects in the sun-
shade when it is extending or retract-
ing, causing improper operation or
damage to the sunshade.

•

Do not push the sunshade arm with
your hands, etc., as this may deform
it. Improper operation or damage to
the sunshade may result.

•

Do not put any object into the sun-
shade inlet port as this may result in
improper operation or damage the
sunshade.

•

Do not hang any object on the arm
rail as this may result in improper op-
eration or damage the sunshade.

•

Do not forcefully pull the sunshade.
Doing so may elongate the sun-
shade. Improper operation or dam-
age to the sunshade may result.

If the moonroof does not close

Have your moonroof checked and re-
paired. It is recommended that you visit a
NISSAN dealer for this service.

LIC4149

Instruments and controls

2-71

When the ON switch

is pushed, map

lights and rear personal lights will auto-
matically turn on and stay on for a period of
time when:
• The doors are unlocked by the Intelligent

Key, a key or the request switch (if so
equipped) while all doors are closed and
the ignition switch is in the OFF position.

• The driver’s door is opened and then

closed while the ignition switch is in the
OFF position.

• Individually pushed.

When the OFF switch

is pushed, the in-

terior lights will illuminate when pushed.
When the DOOR/OFF switch is pushed and
the ON switch is pushed, all of the lights will
come on.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

CONSOLE LIGHT

The console light will turn on whenever the
parking lights or headlights are illuminated.

The console light brightness can be ad-
justed with the illumination brightness
control in the vehicle information display.

LIC2302

LIC2303

INTERIOR LIGHTS

2-72

Instruments and controls

MAP LIGHTS

Press the button to turn the map lights on.
To turn them off, press the button again.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

PERSONAL LIGHTS

To turn the rear personal lights on, push the
switch. To turn them off, push the switch
again.

LUGGAGE COMPARTMENT LIGHT

The light illuminates when the liftgate is
opened. When the liftgate is closed, the
light will turn off. The lights will turn off au-
tomatically after a period of time while
doors are open to prevent the battery from
becoming discharged.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

LIC2304

LIC3907

Rear personal lights

Instruments and controls

2-73

The HomeLink® Universal Transceiver pro-
vides a convenient way to consolidate the
functions of up to three individual hand-
held transmitters into one built-in device.

HomeLink® Universal Transceiver:
• Will operate most Radio Frequency (RF)

devices such as garage doors, gates,
home and office lighting, entry door locks
and security systems.

• Is powered by your vehicle's battery. No

separate batteries are required. If the
vehicle's battery is discharged or is dis-
connected, HomeLink® will retain all
programming.

When the HomeLink® Universal Trans-
ceiver is programmed, retain the original
transmitter for future programming pro-
cedures (Example: new vehicle pur-
chases). Upon sale of the vehicle, the
programmed

HomeLink®

Universal

Transceiver buttons should be erased for
security purposes. For additional infor-
mation, see “Programming HomeLink®”
(P. 2-74).

WARNING

•

Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards
became effective for opener models
manufactured after April 1, 1982.) A
garage door opener which cannot
detect an object in the path of a clos-
ing garage door and then automati-
cally stop and reverse does not meet
current federal safety standards.
Using a garage door opener without
these features increases the risk of
serious injury or death.

•

During the programming procedure
your garage door or security gate will
open and close (if the transmitter is
within range). Make sure that people
or objects are clear of the garage
door, gate, etc., that you are pro-
gramming.

•

Your vehicle's engine should be
turned off while programming the
HomeLink® Universal Transceiver. Do
not breathe exhaust gases; they con-
tain colorless and odorless carbon
monoxide. Carbon monoxide is dan-
gerous. It can cause unconscious-
ness or death.

PROGRAMMING HOMELINK®

The following steps show generic instruc-
tions on how to program a HomeLink® but-
ton. If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com/nissan or call 1-800-
355-3515.

NOTE:

It is also recommended that a new bat-
tery be placed in the hand-held trans-
mitter of the device being programmed
to HomeLink® for quicker programming
and accurate transmission of the radio-
frequency.

HOMELINK® UNIVERSAL
TRANSCEIVER (if so equipped)

2-74

Instruments and controls

䊊

HomeLink® buttons (1–3)

䊊

Indicator light (appears above each
HomeLink® button)

1. Position the end of your hand-held

transmitter 1-3 inches (2-8 cm) away
from the HomeLink® button that you
would wish to program while keeping
the indicator light in view.

2. Simultaneously press and hold both the

chosen HomeLink® and hand-held trans-
mitter buttons until the HomeLink® indi-
cator light changes from a slow to a rap-
idly blinking light. Now you may release
both the HomeLink® and hand-held
transmitter buttons.

NOTE:

Some hand-held transmitters (garage
door opener remote) may actually train
better at a distance of 6–12 inches (15–
20 cm). Keep this in mind if you have
difficulty with the programming process.

3. Firmly

press, hold for five seconds and

release

the programmed HomeLink®

button up to two separate times to ac-
tivate the door. If the door does not acti-
vate, press and hold the just trained
HomeLink® button and observe the indi-
cator light.

• If the indicator light

stays on con-

stantly, programming is complete

and your device should activate when
the Homelink® button is pressed and
released.

• If the indicator light blinks

rapidly for

two seconds and then turns to a
constant light, continue with “Pro-
gramming” steps 4–6

to complete

the programming of a rolling code
equipped device (most commonly a
garage door opener).

LIC5068

LIC5069

Instruments and controls

2-75

NOTE:

Some devices may require you to replace
this Programming Step 2 with procedures
noted in the “Programming HomeLink® for
Canadian customers and gate openers”
(P. 2-76) section. If the HomeLink® indica-
tor light does not change to a rapidly blink-
ing light after performing these steps, con-
tact HomeLink® at www.homelink.com.

4. At the garage door opener motor (secu-

rity gate motor, etc.), locate the “Learn” or
“Set” button. This can usually be found
where the hanging antenna wire is at-
tached to the motor-head unit (see the
device’s manual to identify this button.).
The name and color of the button may
vary by manufacturer.

NOTE:

A ladder and/or second person may sim-
plify the following steps. Do not stand on
your vehicle to perform the next steps.

5. Firmly press and release the “Learn” or

“Set” button until the indicator illumi-
nates. Once the button is pressed, you
have approximately 30 seconds to initi-
ate the next step.

6. Return to the vehicle and firmly press,

hold for two seconds and release the
HomeLink® button up to three times.

not press the HomeLink® button rap-
idly.

At this point programming is com-

plete and your device should operate
when the HomeLink® button is pressed
and released.

7. If you have any questions or are having

difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site
at: www.homelink.com/nissan or call
1-800-355-3515.

PROGRAMMING HOMELINK® FOR
CANADIAN CUSTOMERS AND GATE
OPENERS

Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission –
which may not be long enough for
HomeLink® to pick up the signal during
training. Similar to this Canadian law, some
U.S. gate operators are designed to “time-
out” in the same manner.

If you live in Canada or you are having diffi-
culties training a gate operator

garage

door opener by using the “Programming
HomeLink®” procedures,

replace

“Program-

ming HomeLink®”

step 2

with the following:

NOTE:

When

programming

garage

door

opener, etc., unplug the device during
the “cycling” process to prevent possible
damage to the device components.

LIC4798

Example

2-76

Instruments and controls

Step 2: Continue to press and hold the
HomeLink® button while you press and re-
lease – every two seconds (“cycle”) your
hand-held transmitter until the HomeLink®
indicator light changes from a slow to a
rapidly blinking light. Now you may release
both the Homelink® and hand-held trans-
mitter buttons.

Proceed with “Programming HomeLink®”
step 3 to complete.

Remember to plug the device back in when
programming is completed.

OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER

The HomeLink® Universal Transceiver, after
it is programmed, can be used to activate
the programmed device. To operate, firmly
press

the

appropriate

programmed

HomeLink® button. The indicator light will
illuminate in green with three parenthesis

on the mirror while the signal is being

transmitted.

PROGRAMMING TROUBLE-
SHOOTING

If the HomeLink® does not quickly learn the
hand-held transmitter information:
• Replace the hand-held transmitter bat-

teries with new batteries.

• Position the hand-held transmitter with

its battery area facing away from the
HomeLink® button.

• Press and hold both the HomeLink® but-

ton and hand-held transmitter button in
each step without interruption.

• Position the hand-held transmitter 1 to 3

in (2 to 8 cm) away from the HomeLink®
button. Hold the transmitter in that posi-
tion for up to 15 seconds. If HomeLink® is
not programmed within that time, try
holding the transmitter in another posi-
tion – for example, 6 to 12 in (15 to 20 cm)
away, keeping the HomeLink® button in
view at all times.

It is recommended not to place metal ob-
jects near the garage door opener an-
tenna for optimal functionality.

If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com/nissan or call 1-800-
355-3515.

CLEARING THE PROGRAMMED
INFORMATION

The following procedure clears the pro-
grammed information from three buttons.
Individual buttons cannot be cleared. How-
ever, individual buttons can be repro-
grammed. For additional information, see
“Reprogramming a single HomeLink® but-
ton” (P. 2-78).

To clear all programming

1. Press and hold the two outer HomeLink®

buttons until the indicator light begins to
flash in green in approximately 10 sec-
onds. Do not hold for longer than 20
seconds.

2. Release both buttons.

HomeLink® is now in the programming
mode and can be programmed at any time
beginning with “Programming HomeLink®” -
Step 1.

Instruments and controls

2-77

REPROGRAMMING A SINGLE
HOMELINK® BUTTON

To reprogram a HomeLink® button, com-
plete the following:

1. Press and hold the desired HomeLink®

button.

DO NOT

release the button.

2. The indicator light will begin to flash af-

ter 20 seconds. Without releasing the
HomeLink® button, proceed with “Pro-
gramming HomeLink®” — step 1.

For

questions

comments,

contact

HomeLink® at: www.homelink.com/nissan
or 1–800–355–3515.

The HomeLink® button has now been re-
programmed. The new device can be acti-
vated by pressing the HomeLink® button
that was just programmed. This procedure
will not affect any other programmed
HomeLink® buttons.

If a new device is not programmed to the
HomeLink® button, it will revert to the pre-
viously stored programming.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should change
the codes of any non-rolling code device
that has been programmed into HomeLink®.
Consult the Owner's Manual of each device
or call the manufacturer or dealer of those
devices for additional information.

When your vehicle is recovered, you will
need to reprogram the HomeLink® Uni-
versal Transceiver with your new trans-
mitter information.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

For Canada:

This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause
undesired operation of the device.

2-78

Instruments and controls

Nissan Murano (2024 year). Manual in english - page 5