Nissan Altima (2024 year). Manual in english

OIL CONTROL SYSTEM (if so
equipped)

The oil control system can be accessed in
the Maintenance portion of the vehicle in-
formation display settings.

Engine oil information informs the distance
to oil change. Never exceed one year or
7,500 miles (12000 km) between oil change
intervals for the 2.0L 4 cylinder (KR20DDET
engine model) or 10,000 miles (16,000 km)
between oil change intervals for the 2.5L 4
cylinder (PR25DD engine model).

Display when
ignition is ON

Display timing

Action
Required

Engine Oil
Service due in
xxx miles

Remaining oil
life is less than
940 miles (1500
km).

Plan to have
your vehicle
serviced.

Engine Oil
Service due

Remaining oil
life is 0 miles
(0 km).

Have your ve-
hicle serviced
within two
weeks or less
than 500 miles
(800 km).

The oil change interval cannot be adjusted
manually.

The distance to oil change interval is calcu-
lated depending on the driving conditions
and set automatically by the oil control sys-
tem. A reminder will be displayed when ap-
proaching the end of the service interval.

When the Factory Reset option is selected
in the vehicle information display, the oil
control system will also be reset to initial
value. Please change the engine oil when
Factory Reset is selected.

CAUTION

If the oil replacement indicator is dis-
played, change the engine oil within
two weeks or less than 500 miles (800
km).

Operating the vehicle with deteriorated
oil can damage the engine.

To reset oil control system:

1. Place the ignition switch in the ON

position.

2. Press the

and

buttons located

on the steering wheel until “Settings” dis-
plays in the vehicle information display.
Use the

buttons to select

“Maintenance”.

Then,

press

the

button.

3. Select the “Oil Control System” and press

the OK button.

4. Press the OK button according to the

reset instructions displayed at the bot-
tom of the “Oil Control System” mainte-
nance screen.

For additional information, see “Oil control
system” (P. 9-7).

SETTINGS

The setting mode allows you to change the
information displayed in the vehicle infor-
mation display. It also allows you to change
vehicle functions:
• VDC Setting
• Driver Assistance
• TPMS Setting
• Clock
• Vehicle Settings
• Maintenance
• Customize Display
• Unit/Language
• Key-Linked Settings (if so equipped)
• Factory Reset

2-44

Instruments and controls

VDC Setting

The VDC Setting menu allows the user to enable or disable the Vehicle Dynamic Control (VDC) system.

Menu item

Explanation

System

Allows the user to turn the VDC system on or off. For additional information, see “Vehicle Dynamic Control
(VDC) system” (P. 5-151).

Driver Assistance

The driver assistance menu allows the user to change the settings for driving, parking, and braking aids.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Steering Assist

Allows user to turn the Steering Assist of the ProPILOT Assist system on or off. For additional information, please
see “ProPILOT Assist” (P. 5-69).

Emergency Brake

Displays available emergency braking options.

Front

Allows user to turn the front emergency braking system on or off. For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian Detection” (P. 5-109) and “Intelligent Forward Collision Warning (I-FCW)”
(P. 5-123).

Rear

Allows user to turn the rear emergency braking system on or off. For additional information, see “Rear Automatic
Braking (RAB)” (P. 5-102).

Lane

Displays available lane options.

Lane Departure Warning

Allows user to turn the Lane Departure Warning (LDW) system on or off. For additional information, see “Lane De-
parture Warning (LDW)” (P. 5-32).

Lane Departure Prevention

Allows user to turn Intelligent Lane Intervention (I-LI) system on or off. For additional information, see “Intelligent
Lane Intervention (I-LI)” (P. 5-39).

Blind Spot

Displays available blind spot options.

Blind Spot Warning

Allows user to turn the Blind Spot Warning (BSW) system on or off. For additional information, see “Blind Spot
Warning (BSW)” (P. 5-45).

Side Indicator Brightness

Allows user to change the brightness of the side indicator.

Instruments and controls

2-45

Menu item

Explanation

Speed Limit Sign

Allows user to turn the Speed Limit Sign recognition on or off. For additional information, see “Traffic Sign Recogni-
tion (TSR)” (P. 5-29).

Parking Aids

Displays available parking aids.

Auto Show Sonar

Allows user to auto display the sonar. For additional information, see “Rear Sonar System (RSS)” (P. 5-155).

Rear

Allows user to turn the rear sonar on or off.

Distance

Allows user to set the distance sensor range to Long/Medium/Short.

Volume

Allows the user to set the parking sensor volume to High/Medium/Low.

Rear Cross Traffic Alert

Allows user to turn the Rear Cross Traffic Alert (RCTA) system on or off. For additional information, see “Rear Cross
Traffic Alert (RCTA)” (P. 5-57).

Driver Attention Alert

Allows user to turn the Intelligent Driver Alertness on or off. For additional information, see “Intelligent Driver Alert-
ness (I-DA)” (P. 5-138).

Timer Alert

Allows user to set the timer alert.

Low Temperature Alert

Allows user to turn the low temperature alert on or off.

Chassis Control

Displays available chassis control options.

Active Trace Control

Allows user to turn the Intelligent Trace Control system on or off. For additional information, see “Intelligent Trace
Control (I-TC)” (P. 5-153).

TPMS Setting

The TPMS settings menu allows the user to change the tire pressure units displayed in the vehicle information display.

Menu item

Explanation

TPMS Setting

Displays available TPMS settings.

Tire Pressure Unit

Allows user to select the tire pressure units that will display in the vehicle information display.

2-46

Instruments and controls

Clock

Menu item

Explanation

Clock

Allows user to adjust the clock settings and time within the vehicle information display. Adjustments that can
be made include automatically setting the time, 12H/24H format, Daylight Saving Time, time zone, and manu-
ally setting the time.
The clock can also be set within the center display. For additional information, refer to the separate
NissanConnect® Owner’s Manual.

Vehicle Settings

The vehicle settings allow the user to change the settings for lights, wipers, locking, keys, and other vehicle settings.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Lighting

Displays the available lighting options.

Welcome Headlight

Allows user to turn the welcome light on or off.

Auto Room Lamp

Allows user to turn the auto room lamp on or off.

Accent Lighting

Allows user to adjust the accent lighting brightness.

Auto Headlight

Allows user to change when the auto headlights activate based on the exterior brightness.

Light Off Delay

Allows user to change the length of time the exterior lights remain on.

Turn indicator

Displays the available turn indicator options.

3 Flashes

Allows user to turn the 3 flash pass feature on or off.

Continuous

Allows user to adjust the continuous feature.

Instruments and controls

2-47

Menu item

Explanation

Locking

Displays the available locking options.

Ext Door Switch

Allows user to turn the exterior door switch on or off. When turned on, the request switch on the door is acti-
vated.

Selective Unlock

Allows user to turn selective unlock on or off. When turned on, only the driver’s door is unlocked after the door
unlock operation. When the door handle request switch on the driver’s or front passenger’s side door is
pushed to be unlocked, only the corresponding door is unlocked first. All the doors can be unlocked if the
door unlock operation is performed again within 60 seconds. When this item is turned off, all the doors will be
unlocked after the door unlock operation is performed once.

Auto Door Unlock

Displays the auto door unlock options.

Shift to P

Doors will unlock when the vehicle is shifted into P (Park).

IGN OFF

Doors will unlock when the ignition is turned off.

OFF

Doors will have to be manually unlocked.

Horn beeps on lock

Allows user to turn answer back horn on or off. When turned on, the horn will chirp and the hazard indicators
will flash twice when locking the vehicle with the Intelligent Key.

Wipers

Displays the available wiper options.

Speed Dependent

Allows user to turn wiper with speed on or off.

Driving Position

Displays the available driving position options.

Exit Seat Slide

Allows the user to turn the exit seat slide on or off. When turned on, this feature will move the driver’s seat
backward for an easy exit when the ignition is turned off and the driver’s door is opened. After getting into
the vehicle and placing the ignition switch in the ON position, the driver’s seat will move to the previous set
position. For additional information, see “Memory seat” (P. 3-30).

Rear Door Alert

Displays the available Rear Door Alert options. For additional information, see “Rear Door Alert” (P. 2-78).

Horn & Alert

When selected, the alert is displayed and horn sounds.

Alert Only

When selected, only the alert is displayed.

OFF

When selected, no alert or horn will be active.

Remote Engine Start

Allows user to turn the Remote Engine Start on or off. When turned on, the engine can be restarted remotely.
For additional information, see “Remote Engine Start” (P. 5-17).

2-48

Instruments and controls

Maintenance

The maintenance menu allows the user to set reminders for various vehicle maintenance items.

WARNING

The tire replacement indicator is not a substitute for regular tire checks, including tire pressure checks. For additional informa-
tion, see “Changing wheels and tires” (P. 8-39). Many factors including tire inflation, alignment, driving habits and road conditions
affect tire wear and when tires should be replaced. Setting the tire replacement indicator for a certain driving distance does not
mean your tires will last that long. Use the tire replacement indicator as a guide only and always perform regular tire checks.
Failure to perform regular tire checks, including tire pressure checks could result in tire failure. Serious vehicle damage could
occur and may lead to a collision, which could result in serious personal injury or death.

Menu item

Explanation

Maintenance

Displays various maintenance reminder options.

Oil Control System

Allows user to reset the current interval. This should only be done after completing oil change maintenance.

Oil and Filter

Allows user to set a reminder at a specific interval or reset the current one.

Tire

Allows user to set a reminder at a specific interval or reset the current one.

Other

Allows user to set a reminder at a specific interval or reset the current one.

Instruments and controls

2-49

Customize Display

The customize display menu allows the user to customize the information that appears in the vehicle information display.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Main Menu Selection

Displays available screens that can be shown in the vehicle information display.

Home

Allows user to turn the home screen on or off in the vehicle information display.

Blank

Allows user to turn the blank on or off in the vehicle information display.

Audio

Allows user to turn the audio controls screen on or off in the vehicle information display.

Navigation

Allows user to turn the navigation screen on or off in the vehicle information display.

Fuel Economy

Allows user to turn the fuel economy screen on or off in the vehicle information display.

Driving Aids

Allows user to turn the driving aids screen on or off in vehicle information display.

Cruise

Allows user to turn the cruise control screen on or off in the vehicle information display.

Speed Limit Sign

Allows user to turn the speed limit sign screen on or off in the vehicle information display.

TPMS

Allows user to turn the TPMS screen on or off in the vehicle information display.

Variable Compression Turbo

Allows user to turn the Variable Compression Turbo screen on or off in the vehicle information display.

Speed

Allows user to turn the speedometer screen on or off in the vehicle information display.

Drive Computer

Allows user to turn the drive computer screen on or off in the vehicle information display.

Auto Turn Notification

Displays the available auto turn notification settings.

Alerts

Allows user to turn the auto turn notification alerts on or off.

Cruise Screen Transition

Allows user to turn the cruise screen transition on or off.

Welcome Effect

Displays the available welcome effect settings.

Gauges

Allows user to turn the gauges effect on or off.

Animation

Allows user to turn the animation effect on or off.

Light/Wiper Guidance

Displays the available light and wiper guidance settings.

Lights mode guidance

Allows user to turn the light mode guidance on or off.

Wiper mode guidance

Allows user to turn the wiper mode guidance on or off.

2-50

Instruments and controls

Unit/Language

The unit/language menu allows the user to change the units shown in the vehicle information display.

Menu item

Explanation

Mileage/Fuel

Displays the available mileage/fuel display units and allows user to select preferred unit for display.

Tire Pressure

Allows user to select the tire pressure display units. Changing the tire pressure units will also change the
units displayed for the Variable Compression Turbo (if so equipped).

Temperature

Allows user to select the temperature display units.

Language

Displays the available language options and allows user to select preferred language for display.

Key-Linked Settings (if so equipped)

Menu item

Explanation

Key-Linked Settings

Allows user to turn the Key-Linked Settings on or off. For additional information, see “Memory storage func-
tion” (P. 3-30).

Factory Reset

The factory reset menu allows the user to restore the vehicle information display settings to factory status.

Menu item

Explanation

Factory Reset

Allows user to reset the vehicle information display settings to the original factory settings. Once selected,
the user can confirm or cancel the reset.

Instruments and controls

2-51

VEHICLE INFORMATION DISPLAY
WARNINGS AND INDICATORS

The following messages may appear in
your vehicle information display.

Place the key near the start
switch

This indicator appears when the battery of
the Intelligent Key is low and when the In-
telligent Key system and the vehicle are not
communicating normally.

If this appears, touch the ignition switch
with the Intelligent Key while depressing
the brake pedal. For additional information,
see “Battery replacement” (P. 8-24).

Key Battery Low

This indicator appears when the Intelligent
Key battery is running out of power.

If this indicator appears, replace the bat-
tery with a new one. For additional infor-
mation, see “Battery replacement” (P. 8-24).

Key ID Incorrect

This warning appears when the ignition
switch is placed from the OFF position and
the Intelligent Key is not recognized by the

system. You cannot start the engine with
an unregistered key.

For additional information, see “NISSAN In-
telligent Key®” (P. 3-6).

Key System Error: See
Owner’s Manual

After the ignition switch is placed in the ON
position, this warning appears for a period
of time and then turns off.

The Key System Error message warns of a
malfunction with the Intelligent Key sys-
tem. If the warning appears while the en-
gine is stopped, it may be impossible to
start the engine.

If the warning appears while the engine is
running, you can drive the vehicle. However,
in these cases, have the system checked. It
is recommended that you visit a NISSAN
dealer for this service.

No Key Detected

This warning appears when the Intelligent
Key is left outside the vehicle with the igni-
tion switch in the ON position. Make sure
the Intelligent Key is inside the vehicle.

For additional information, see “NISSAN In-
telligent Key®” (P. 3-6).

Brightness indicator

This indicator appears when the vehicle
information display screen brightness is
being adjusted.

Chassis Control System Error: See
Owner’s Manual

This warning appears if there is an error in
the Automatic Brake Hold system. Have the
system checked. It is recommended that
you visit a NISSAN dealer for this service.
For additional information, see “Chassis
control” (P. 5-153) or “Automatic brake hold”
(P. 5-26).

Rear Door Alert is activated

When the system is enabled, this message
appears when the Rear Door Alert system
is active and can remind the driver to check
the back seat.
• Using the steering wheel switch, a driver

can select “Dismiss Message” to clear the
display for a period of time. If no selection
is made, this message automatically
turns off after a period of time.

• Using the steering wheel switch, a driver

can select “Disable Alert” to disable the
horn alert for the remainder of the cur-
rent trip.

2-52

Instruments and controls

WARNING

Selecting “Dismiss Message” during a
stop within a trip temporarily dis-
misses the message for that stop with-
out turning the system off. Alerts can
be provided for other stops during the
trip. Selecting “Disable Alert” turns off
the Rear Door Alert system for the re-
mainder of a trip and no audible alert
will be provided.

NOTE:

This system is disabled until a driver en-
ables it using the vehicle information
display. For additional information, see
“How to use the vehicle information dis-
play” (P. 2-39).

For additional information, see “Rear Door
Alert” (P. 2-78).

Check Rear Seat For All Articles

When the system is enabled, this message
appears when the vehicle comes to a com-
plete stop, the vehicle is transitioned from
the D (Drive) position to P (Park) position,
and the driver exits the vehicle. This mes-
sage alerts the driver, after a period of time,
to check for items in the rear seat after the
audible alert has been provided.

NOTE:

This system is disabled until a driver en-
ables it using the vehicle information
display. For additional information, see
“How to use the vehicle information dis-
play” (P. 2-39).

For additional information, see “Rear Door
Alert” (P. 2-78).

Door/Trunk Open

This warning appears when a door or the
trunk has been opened.

Drive sport mode indicator

A small “S” appears to the right of the Trans-
mission Shift Position indicator in the ve-
hicle information display when the drive
sport mode is engaged.

Activate the drive sport mode by pushing
the switch on the shift lever while the shift
lever is in the D (Drive) position.

For additional information, see “Driving the
vehicle” (P. 5-17 ).

Engine Oil Service due
in – – – miles

This distance to oil change will display if the
distance to oil change is approximately
1,000 miles (1,600 km) or less. Several re-
minders will display until the remaining dis-
tance is 0.

Engine Oil Service due now

This message will be displayed when re-
maining distance is 0, indicating service is
now due/overdue. After service is com-
pleted, the Oil Control System should be
reset

from

the

Maintenance

settings

menu.

Headlight System Error: See Owner’s
Manual

This warning appears when there is an er-
ror with the system. For additional informa-
tion, see “Headlight and turn signal switch”
(P. 2-64).

Loose Fuel Cap

This warning appears when the fuel-filler
cap is not tightened correctly after the ve-
hicle has been refueled. For additional in-
formation, see “Fuel-filler cap” (P. 3-24).

Instruments and controls

2-53

Low Fuel

This warning appears when the fuel level in
the fuel tank is getting low. Refuel as soon
as it is convenient, preferably before the
fuel gauge reaches 0 (Empty).

There will be

a small reserve of fuel in the tank when
the fuel gauge needle reaches 0 (Empty).

Low outside temperature
indicator

This indicator appears if the outside tem-
perature is below 37°F (3°C). The tempera-
ture can be changed to display in Fahren-
heit or Celsius. For additional information,
see “Unit” (P. 2-30).

Low Washer Fluid

This warning appears when the windshield-
washer fluid is at a low level. Add windshield-
washer fluid as necessary. For additional
information, see “Windshield-washer fluid”
(P. 8-12).

Power will turn off to save the battery

This message appears after a period of
time if the ignition switch is in the ON posi-
tion and if the vehicle is in P (Park). For ad-
ditional information, see “Push-button igni-
tion switch positions” (P. 5-13).

Power turned off to save the battery

This message appears after the ignition
switch is automatically turned off. For addi-
tional information, see “Push-button igni-
tion switch positions” (P. 5-13).

Press Brake Pedal

This message may appear in the following
situations:
• The driver tries to release the electronic

parking brake manually without depress-
ing the brake pedal.

• The vehicle is stopped on a steep hill; and

there is a possibility of moving back-
wards, even if the electronic parking
brake is applied.

• The vehicle moves while the automatic

brake hold is activated.

For additional information, see “Electronic
parking brake” (P. 5-24).

Push brake and start
switch to drive

This indicator appears when the shift lever
is in the P (Park) position and the vehicle
has not been started. Start the engine by
pushing the ignition switch with the brake
pedal depressed. You can start the engine
from any position of the ignition switch.

This message also appears when the ve-
hicle has been started using the Remote
Engine Start function (if so equipped). Push
the ignition switch with the brake pedal
depressed to place the ignition switch in
the ON position. For additional information,
see “Remote Engine Start” (P. 3-18).

Release Parking Brake

This warning appears when the parking
brake is set and the vehicle is driven.

Reminder: Turn OFF
Headlights

This warning appears when the headlights
are left in the ON position when exiting the
vehicle. Place the headlight switch in the
OFF or AUTO position. For additional infor-
mation, see “Headlight and turn signal
switch” (P. 2-64)

Rear seat belt warning

• This warning includes display of the seat

belts for rear positions only. Rear seat
belts that are unfastened will appear red.

• If any rear seat belts are unfastened

when the ignition switch is pushed to the
ON position, this warning will display for
about one minute, or until dismissed.

2-54

Instruments and controls

• When a rear seat belt is changed from

fastened to unfastened, this warning will
display for over one minute, or until
dismissed.

• If the vehicle is driven above 9 mph (15

km/h) during or after the status change,
this warning will display and the chime
will sound for over one minute. During
this time, the warning and chime cannot
be dismissed unless the rear seat belt is
fastened again.

NOTE:

Opening and closing a rear door while
stopped will reset this warning, similar to
pushing the ignition switch to ON again.

Shift to Park

This warning appears when the ignition
switch is in the AUTO ACC or OFF position
and the shift lever is not in the P (Park)
position. Also, a chime sounds when the
ignition switch is in the AUTO ACC or OFF
position.

If this warning appears, move the shift lever
to the P (Park) position and start the engine.

Shipping Mode On Push Storage Fuse

This warning may appear if the extended
storage switch is not pushed in. When this
warning appears, push in the extended
storage switch to turn off the warning. For
additional information, see “Extended stor-
age switch” (P. 2-80).

Timer Alert Time for a
break?

This message appears when the set time
is reached. This time can be set up to six
hours. For additional information, see
“Driver Assistance” (P. 2-45)

Tire Pressure Low - Add Air

This warning appears when the low tire
pressure warning light in the meter illumi-
nates and low tire pressure is detected. The
warning appears each time the ignition
switch is placed in the ON position as long
as the low tire pressure warning light re-
mains illuminated. If this warning appears,
stop the vehicle and adjust the tire pres-
sures of all four tires to the recommended
COLD tire pressure shown on the Tire and
Loading Information label. For additional
information, see “Low tire pressure warning
light” (P. 2-15) and “Tire Pressure Monitoring
System (TPMS)” (P. 5-5).

Transmission Shift Position
indicator

This indicator shows the transmission shift
position.

AWD Error: See Owner’s
Manual

This warning appears when the All-Wheel
Drive (AWD) system is not functioning prop-
erly while the engine is running.

AWD High Temp. Stop
Vehicle

This warning may appear while trying to free
a stuck vehicle due to increased oil tempera-
ture. The driving mode may change to
2-Wheel Drive (2WD). If this warning is dis-
played, stop the vehicle with the engine
idling, as soon as it is safe to do so. Then if the
warning turns off, you can continue driving.

Tire Size Incorrect See
Owner’s Manual

This warning may appear if there is a large
difference between the diameters of the
front and rear wheels. Pull off the road in a
safe area, with the engine idling. Check that
all the tire sizes are the same, that the tire
pressure is correct and that the tires are
not excessively worn.

Instruments and controls

2-55

CVT (AT) Malfunction
Service now

This warning appears when there is a prob-
lem with the CVT system. If this warning ap-
pears, have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

CVT (AT) hot Power reduced

This transmission has a high fluid tem-
perature protection mode. If the fluid tem-
perature becomes too high (for example,
climbing steep grades in high tempera-
tures with heavy loads, such as when tow-
ing a trailer), engine power and, under
some conditions, vehicle speed will be
decreased automatically to reduce the
chance of transmission damage. Vehicle
speed can be controlled with the accelera-
tor pedal, but the engine and vehicle speed
may be reduced.

WARNING

When the high fluid temperature pro-
tection mode operation occurs, vehicle
speed may be gradually reduced. The
reduced speed may be lower than
other traffic, which could increase the
chance of a collision. Be especially

careful when driving. If necessary, pull
to the side of the road at a safe place
and allow the transmission to return to
normal operation; or have it repaired if
necessary.

CVT Stop the vehicle

This message appears 30 seconds before
the vehicle is shut down due to an above
normal operating transmission tempera-
ture. The Malfunction Indicator Light (MIL)
and malfunction warning (red) will illumi-
nate. Have the system checked. It is recom-
mended that you visit a NISSAN dealer im-
mediately for this service.

Automatic Emergency
Braking (AEB) with
Pedestrian Detection
emergency warning
indicator

This indicator appears along, with an au-
dible warning, when the system detects
the possibility of a forward collision.

For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian
Detection” (P. 5-109).

Blind Spot Warning (BSW)
indicator

This indicator appears when the BSW sys-
tem is engaged.

For additional information, see “Blind Spot
Warning (BSW)” (P. 5-45).

Cruise control indicator

This indicator shows the cruise control sys-
tem status.

When cruise control is activated, a green
circle will appear to indicate it is set. The
vehicle information display will also display
the speed the cruise control was set at. If you
accelerate past the set speed, the speed will
blink until you either cancel cruise control or
go back to the set speed. If cruise control is
on and canceled, the speed will be displayed
to show the speed the vehicle will return to if
the resume button is activated.

Currently not available

This message may appear when the ProPI-
LOT Assist system or the Intelligent Lane
Intervention (I-LI) system is engaged.

Under the following conditions, the ProPI-
LOT Assist or the Intelligent Lane Interven-
tion (I-LI) system is automatically canceled:
• When the VDC system is turned off

2-56

Instruments and controls

The above system cannot be used in some
situations (VDC operates, wheel slip and
VDC system is off.)

DAA Malfunction

This warning appears when the Intelligent
Driver Alertness (I-DA) system is not func-
tioning properly. For additional information,
see “Intelligent Driver Alertness (I-DA)”
(P. 5-138).

Driver Attention Alert—
Take a Break?

This alert appears when the system has
detected that the driver may be displaying
fatigue or a lack of attention.

Forward Driving Aids temporarily
disabled Front Sensor blocked See
Owner’s Manual

This message appears when the front ra-
dar sensor may be obstructed due to:
• mud, dirt, snow, ice, etc.
• inclement weather (rain, fog, snow, etc.).

All forward driving aids are temporarily dis-
abled until the system detects that the
front radar sensor is no longer obstructed.

For additional information, see:
• Automatic Emergency Braking (AEB) with

Pedestrian Detection (P. 5-109)

• ProPILOT Assist (P. 5-69)
• Intelligent

Forward

Collision

Warning

(I-FCW) (P. 5-123)

Intelligent Lane
Intervention (I-LI)/
ProPILOT Assist status
indicator

This indicator shows when the I-LI or ProPI-
LOT Assist system is engaged.

For additional information, see “Intelligent
Lane Intervention (I-LI)” (P. 5-39) or “ProPILOT
Assist” (P. 5-39).

Lane Departure Warning
(LDW) indicator

This indicator shows when the LDW system
is engaged.

For additional information, see “Lane De-
parture Warning (LDW)” (P. 5-32) and “Intelli-
gent Lane Intervention (I-LI)” (P. 5-39).

Malfunction

This warning appears when one or more of
the following systems (if so equipped) is
not functioning properly:
• Automatic Emergency Braking (AEB) with

Pedestrian Detection

• Intelligent

Forward

Collision

Warning

(I-FCW)

If one or more of these warning appears,
have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian
Detection” (P. 5-109) or “Intelligent Forward
Collision Warning (I-FCW) (P. 5-123).

Malfunction: See Owner’s Manual

This warning appears when one or more of
the following systems (if so equipped) is
not functioning properly:
• Traffic Sign Recognition (TSR)
• Rear Automatic Braking (RAB)

If one or more of these warning appears,
have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Not Available Bad Weather

This message may appear when the Steer-
ing Assist system is engaged.

Under the following conditions, the Steering
Assist system is automatically canceled:
• When the wiper (HI) operates.

Instruments and controls

2-57

• When lane markers in the traveling lane

cannot be correctly detected for a period
of time due to such items as a snow rut,
reflection of light on a rainy day or several
unclear lane markers are present.

If you want to use the Steering Assist sys-
tem again, cancel the ProPILOT Assist sys-
tem and set it again when lane markers are
clearly visible or push the Steering Assist
switch once.

Not Available Front Camera
Obstructed

This message may appear when the Steer-
ing Assist system is engaged.

Under the following conditions, the Steering
Assist system is automatically canceled:
• The camera area of the windshield is

fogged up or covered with dirt, water
drops, ice, snow, etc.

Not Available Parking Brake On

This message may appear when the ProPI-
LOT Assist system is engaged.

Under the following condition, the ProPILOT
Assist system is automatically canceled:
• The electronic parking brake is applied.

The above system cannot be used when
the electronic parking is activated.

For additional information, see "ProPILOT
Assist (P. 5-69) and “Parking brake” (P. 5-24).

Not Available Poor Road Conditions

This message may appear when the ProPI-
LOT Assist system or the Intelligent Lane
Intervention (I-LI) system is engaged.

Under the following conditions, the ProPI-
LOT Assist system or the Intelligent Lane
Intervention (I-LI) system is automatically
canceled:
• When the VDC system operates
• When a wheel slips

The above system cannot be used in some
situations (VDC operates, wheel slip and
VDC system is off.)

Not Available Seat Belt Not Fastened

This message may appear when the ProPI-
LOT Assist system is engaged.

Under the following condition, the ProPILOT
Assist system is automatically canceled:
• When the driver’s seat belt is not fastened

The above system cannot be used when
the driver’s seat belt is not fastened.

Not Available System Malfunction

This warning appears when one or more of
the following systems (if so equipped) is
not functioning properly.
• ProPILOT Assist
• Blind Spot Warning (BSW)
• Lane Departure Warning (LDW)
• Intelligent Lane Intervention (I-LI)

If one or more of these warnings appear,
have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

For additional information, see ProPILOT
Assist” (P. 5-69), “Blind Spot Warning (BSW)”
(P. 5-45), “Lane Departure Warning (LDW)”
(P. 5-32) or “Intelligent Lane Intervention
(I-LI)” (P. 5-39).

Only Available with Cruise
Control ON

This message appears when the Steering
Assist switch has been pushed while the
cruise control is not switched on.

For additional information, see “Intelligent
Cruise Control (ICC) (for vehicles with ProPI-
LOT Assist)” (P. 5-155).

2-58

Instruments and controls

Parking Sensor

This indicator appears when the sensor is
activated. For additional information, see
“Rear Sonar System (RSS)” (P. 5-155).

Parking Sensor Error: See Owner’s
Manual

This warning appears when there is an er-
ror with the system. For additional informa-
tion, see “Rear Sonar System (RSS)” (P. 5-156).

ProPILOT Assist indicators

These indicators show the ProPILOT Assist
system status. The status is shown by
color. For additional information, see “Pro-
PILOT Assist” (P. 5-69).

Rear Automatic Braking
(RAB) system warning
indicator

This indicator appears to indicate the sta-
tus of the Rear Automatic Braking (RAB)
system. For additional information, see
“Rear Automatic Braking (RAB)” (P. 5-102).

Speed Limit Sign indicator

This message may appear when the Traffic
Sign Recognition system is engaged.

For additional information, see “Traffic Sign
Recognition (TSR)” (P. 5-29).

Steering Assist Alert

This message may appear when the Steer-
ing Assist system is engaged.

It will be displayed under the following
condition:
• When not holding the steering wheel or

when there is no steering wheel operation

Please hold on the steering wheel immedi-
ately. When the steering operation is de-
tected, the warning turns off and the steer-
ing assist function is automatically restored.

Steering Assist Not Available Cannot
Detect Lane

This indicator may appear when the Steer-
ing Assist system is engaged. The Steering
Assist system is automatically cancelled
when the lane markers in the traveling lane
cannot be correctly detected for a period
of time due to such items as a snow rut,
reflection of light on a rainy day or several
unclear lane markers are present.

If you want to use the Steering Assist sys-
tem again, cancel the ProPILOT Assist sys-
tem and set it again when the lane markers
are clearly visible or by pushing the Steer-
ing Assist switch once.

Steering Assist indicator

This indicator appears when the Steering
Assist system is engaged.

For additional information, see “ProPILOT
Assist” (P. 5-69).

Steering Assist ON

This message appears when the Steering
Assist system is turned on.

For additional information, see “Steering
Assist” (P. 5-69).

Steering Assist OFF

This message appears when the Steering
Assist system is turned off.

For additional information, see “Steering
Assist” (P. 5-69).

Instruments and controls

2-59

Unavailable: High Cabin Temperature

This message appears when the camera
detects an interior temperature of more
than 104°F (40°C). For additional informa-
tion, see “ProPILOT Assist” (P. 5-69), “Intelli-
gent Lane Intervention (I-LI)” (P. 5-39), “Lane
Departure Warning (LDW)” (P. 5-32) or “Traffic
Sign Recognition (TSR) . (P. 5-29).

Unavailable: Side Radar Obstruction

This message appears when the Blind
Spot Warning (BSW)/Rear Cross Traffic Alert
(RCTA) systems become unavailable be-
cause a radar blockage is detected. For
additional information, see “Blind Spot
Warning (BSW)” (P. 5-45) or “Rear Cross Traf-
fic Alert (RCTA)” (P. 5-57).

Vehicle ahead detection
indicator

This indicator shows when the following
systems are engaged and have detected a
vehicle:
• Automatic Emergency Braking (AEB) with

Pedestrian Detection

• Intelligent

Forward

Collision

Warning

(I-FCW)

For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian
Detection” (P. 5-109) or “Intelligent Forward
Collision Warning (I-FCW)” (P. 5-123).

Your vehicle may have two types of security
systems:
• Vehicle security system
• NISSAN Vehicle Immobilizer System

VEHICLE SECURITY SYSTEM

The vehicle security system provides visual
and audible alarm signals if someone
opens the doors or trunk when the system
is armed. It is not, however, a motion detec-
tion type system that activates when a ve-
hicle is moved or when a vibration occurs.

The system helps deter vehicle theft but
cannot prevent it, nor can it prevent the
theft of interior or exterior vehicle compo-

nents in all situations. Always secure your
vehicle even if parking for a brief period.
Never leave your keys in the vehicle, and
always lock the vehicle when unattended.
Be aware of your surroundings, and park in
secure, well-lit areas whenever possible.

Many devices offering additional protec-
tion, such as component locks, identifica-
tion markers, and tracking systems, are
available at auto supply stores and spe-
cialty shops. A NISSAN dealer may also offer
such equipment. Check with your insur-
ance company to see if you may be eligible
for discounts for various theft protection
features.

How to arm the vehicle security
system

1. Close all windows and the moonroof.

The system can be armed even if the
windows and moonroof (if so equipped)
are open.

2. Remove the Intelligent Key from the

vehicle.

3. Close all doors, hood and trunk. Lock all

doors. The doors can be locked with the
Intelligent Key, door handle request
switch, or power door lock switch.

LIC0301

SECURITY SYSTEMS

2-60

Instruments and controls

4. Confirm that the

indicator light

comes on. The

indicator stays

illuminated for a period of time indicat-
ing that the system is in the pre-armed
phase.
The

indicator light will blink every

3 seconds once the security system is
armed.
If during the pre-armed phase one of
the following occurs, the system will not
arm:

• Any door is unlocked with the Intelligent

Key or door request switch.

• The ignition switch is placed in the ON

position.

•

Even when the driver and/or passen-
gers are in the vehicle, the system will
activate when all the doors, hood and
trunk are locked with the ignition
switch placed in the LOCK position.
When placing the ignition switch in the
AUTO ACC or ON position, the system
will be released.

Vehicle security system activation

The vehicle security system will give the
following alarm:
• The headlights blink and the horn sounds

intermittently.

• The alarm automatically turns off after a

period of time. However, the alarm reacti-
vates if the vehicle is tampered with
again. The alarm can be shut off by press-
ing the

button on the Intelligent Key.

The alarm is activated by:
• opening the door or trunk without using

Intelligent Key (even if the door is un-
locked by releasing the door inside lock
knob switch).

How to stop an activated alarm

The alarm stops only by unlocking a door
by pressing the

button on the Intelli-

gent Key or pushing the request switch on
the driver's or passenger's door with the
Intelligent Key in range of the door handle.

NISSAN VEHICLE IMMOBILIZER
SYSTEM

The NISSAN Vehicle Immobilizer System
will not allow the engine to start without
the use of a registered key.

If the engine fails to start using a registered
key (for example, when interference is
caused by another registered key, an auto-
mated toll road device or automatic pay-
ment device on the key ring), restart the
engine using the following procedures:

1. Leave the ignition switch placed in the ON

position for approximately 5 seconds.

2. Place the ignition switch in the OFF or

LOCK position, and wait approximately
10 seconds.

3. Repeat steps 1 and 2.

4. Restart the engine while holding the de-

vice (which may have caused the inter-
ference) separate from the registered
key.

If the no start condition re-occurs, NISSAN
recommends placing the registered key on
a separate key ring to avoid interference
from other devices.

Instruments and controls

2-61

FCC Notice:

For USA:

This device complies with part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's author-
ity to operate the equipment.

For Canada:

This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference (2) This de-
vice must accept any interference, in-
cluding interference that may cause un-
desired operation of the device.

Security indicator light

The security indicator light blinks whenever
the ignition switch is placed in the OFF,
LOCK or AUTO ACC position.

This function indicates the NISSAN Vehicle
Immobilizer System is operational.

If the NISSAN Vehicle Immobilizer System is
malfunctioning, the light will remain on
while the ignition switch is placed in the ON
position.

If the light still remains on and/or the
engine will not start, seek service for the
NISSAN Vehicle Immobilizer System as
soon as possible. Please bring all regis-
tered keys that you have. It is recom-
mended that you visit a NISSAN dealer
for this service.

LIC0474

2-62

Instruments and controls

SWITCH OPERATION

WARNING

In freezing temperatures the washer
solution may freeze on the windshield
and obscure your vision which may
lead to an accident. Warm the wind-
shield with the defroster before you
wash the windshield.

CAUTION

•

Do not operate the washer continu-
ously for more than 30 seconds.

•

Do not operate the washer if the
windshield-washer fluid reservoir is
empty.

•

Do not fill the windshield-washer
fluid

reservoir

with

windshield-

washer fluid concentrates at full
strength.

Some

methyl

alcohol

based windshield-washer fluid con-
centrates may permanently stain the
grille

spilled

while

filling

the

windshield-washer fluid reservoir.

•

Pre-mix

windshield-washer

fluid

concentrates

with

water

the

manufacturer's recommended lev-
els before pouring the fluid into the
windshield-washer fluid reservoir.
Do not use the windshield-washer
fluid reservoir to mix the windshield-
washer fluid concentrate and water.

NOTE:

If the windshield wiper operation is in-
terrupted by snow or ice, the wiper may
stop moving to protect its motor. If this
occurs, turn the wiper switch to the OFF
position and remove the snow or ice that
is on and around the wiper arms. In ap-
proximately 1 minute, turn the switch on
again to operate the wiper.

The windshield wiper and washer operates
when the ignition switch is placed in the ON
position.

Push the lever down to operate the wiper
at the following speed:

䊊

Intermittent — intermittent operation
can be adjusted by turning the knob
toward

(faster) or

(slower).

䊊

Low — continuous low speed operation

䊊

High

—

continuous

high

speed

operation

Push the lever up

to have one sweep

operation (MIST) of the wiper.

Pull the lever toward you

to operate the

washer. The wiper will also operate several
times.

NOTE:

The Wiper with Speed and Wiper Guidance
features may be disabled. For addi-
tional information, see “Vehicle informa-
tion display-5 inch (13 cm) Type A” (P. 2-20)
or “Vehicle information display-7 inch (18
cm) Type B” (P. 2-39).

LIC4896

WIPER AND WASHER SWITCH

Instruments and controls

2-63

To defrost the rear window glass and out-
side mirrors (if so equipped), place the igni-
tion switch in the ON position and push the
rear window defroster switch on. The rear
window defroster indicator light on the
switch comes on. Push the switch again to
turn the defroster off.

The rear window defroster automatically
turns off after approximately 15 minutes.

CAUTION

When cleaning the inner side of the rear
window, be careful not to scratch or
damage the rear window defroster.

NOTE:

The top and bottom few rows of wires on
the rear window are not part of the rear
window defroster system. These wires
make up the antenna for the audio
system.

HEADLIGHT CONTROL SWITCH

Lighting

䊊

Rotate the switch to the

position,

and the front parking, tail, license plate,
and instrument panel lights will come
on. The

will illuminate in the meter.

䊊

Rotate the switch to the

position,

and the headlights will come on and all
the other lights remain on.

LIC4039

LIC2635

Type A (if so equipped)

REAR WINDOW AND OUTSIDE
MIRROR (if so equipped)
DEFROSTER SWITCH

HEADLIGHT AND TURN SIGNAL
SWITCH

2-64

Instruments and controls

NOTE:

The Light Guidance feature may be dis-
abled. For additional information, see “Ve-
hicle information display-5 inch (13 cm)
Type A” (P. 2-20) or “Vehicle information
display-7 inch (18 cm) Type B” (P. 2-39).

CAUTION

Use the headlights with the engine run-
ning to avoid discharging the vehicle
battery.

Autolight system

The autolight system allows the headlights
to turn on and off automatically. The auto-
light system can:
• Turn on the headlights, front parking, tail,

license plate and instrument panel lights
automatically when it is dark.

• Turn off all the lights when it is light.
• Keep all the lights on for a period of time

after you place the ignition switch in the
OFF position and all doors are closed.

NOTE:

Autolight activation sensitivity and the
time delay for autolight shutoff can be
adjusted.
For additional information, see “Vehicle
information display-5 inch (13 cm) Type A”
(P. 2-20) or “Vehicle information display-7
inch (18 cm) Type B” (P. 2-39).

To turn on the autolight system:

For USA:

Turn the headlight switch to the

AUTO position

For CAN:

Turn the headlight switch to the

AUTO

position.

2. Place the ignition switch in the ON

position.

3. The

autolight

system

automatically

turns the headlights on and off.

Initially, if the ignition switch is placed in the
OFF position and a door is opened and left
open, the headlights remain on for a period
of time. If another door is opened while the
headlights are on, then the timer is reset.

To turn the autolight system off:

For USA:

Turn the switch to the OFF (if so

equipped),

, or

position.

LIC4498

Type B (if so equipped)

LIC5096

Instruments and controls

2-65

For CAN:

Turn the switch to the

position.

The headlights will turn on automatically at
twilight or in rainy weather (when the wind-
shield wiper is operated continuously).

If the ignition switch is pushed to the OFF
position and one of the doors is opened
and this condition is continued, the head-
lights remain on for 5 minutes.

Be sure you do not put anything on top
of the autolight sensor located in the
top side

of the instrument panel. The

autolight sensor controls the autolight; if
it is covered, the autolight sensor reacts
as if it is dark out and the headlights
will illuminate. If this occurs while parked
with the engine off and the ignition switch
placed in the ON position, your vehicle's
battery could become discharged.

Headlight beam select

䊊

To select the high beam function, put
the headlight switch in the

posi-

tion and push the lever forward. The
high beam lights come on and the
light illuminates in the meter.

䊊

Pull the lever back to select the low
beam.

䊊

Pulling and releasing the lever flashes
the headlight high beams on and off.

LIC0836

LIC5120

2-66

Instruments and controls

High Beam Assist

The High Beam Assist system will operate
when the vehicle is driven at speeds of ap-
proximately 25 mph (40 km/h) and above.
If an oncoming vehicle or leading vehicle
appears in front of your vehicle when
the headlight high beam is on, the head-
light will be switched to the low beam
automatically.

WARNING

•

The High Beam Assist system is a
convenience but it is not a substitute
for safe driving operation. The driver
should remain alert at all times, en-
sure

safe

driving

practices

and

switch the high beams and low beam
manually when necessary.

•

The high beam or low beam may not
switch automatically under the fol-
lowing conditions. Switch the high
beam and low beam manually.

–

During bad weather (rain, fog,
snow, wind, etc.).

–

When a light source similar to a
headlight or tail light is in the vi-
cinity of the vehicle.

–

When the headlights of the on-
coming vehicle or the leading ve-
hicle are turned off, when the color
of the light is affected due to for-
eign materials on the lights, or
when the light beam is out of
position.

–

When there is a sudden, continu-
ous change in brightness.

–

When driving on a road that
passes over rolling hills, or a road
that has level differences.

–

When driving on a road with many
curves.

–

When a sign or mirror-like surface
is reflecting intense light towards
the front of the vehicle.

–

When the container, etc. being
towed by a leading vehicle is re-
flecting intense light.

–

When a headlight on your vehicle
is damaged or dirty.

–

When the vehicle is leaning at an
angle due to a punctured tire, be-
ing towed, etc.

•

The timing of switching the low
beam and high beam may change
under the following situations.

–

The brightness of the headlights
of the oncoming vehicle or leading
vehicle.

–

The movement and direction of
the oncoming vehicle and the
leading vehicle.

–

When only one light on the on-
coming vehicle or the leading ve-
hicle is illuminated.

–

When the oncoming vehicle or the
leading vehicle is a two-wheeled
vehicle.

–

Road conditions (incline, curve,
the road surface, etc.).

–

The number of passengers and
the amount of luggage.

Instruments and controls

2-67

High Beam Assist operation

To activate the High Beam Assist system,
turn the headlight switch to the AUTO po-
sition

and push the lever forward

(high beam position). The

High Beam

Assist indicator light in the meter will illumi-
nate while the headlights are turned on.

If the High Beam Assist indicator light does
not illuminate in the above condition, it may
indicate that the system is not functioning
properly. Have the system checked, it is
recommended that you visit a NISSAN
dealer for this service.

When the vehicle speed lowers to less than
approximately 16 mph (25 km/h), the head-
light uses the low beam.

To turn off the High Beam Assist system,
turn the headlight switch to the

posi-

tion or select the low beam position by
placing the lever in the neutral position.

Ambient image sensor maintenance

The ambient image sensor

for the High

Beam Assist system is located in front of
the inside mirror. To maintain the proper
operation of the high beam assist system
and prevent a system malfunction, be sure
to observe the following:
• Always keep the windshield clean.
• Do not attach a sticker (including trans-

parent material) or install an accessory
near the ambient image sensor.

• Do not strike or damage the areas

around the ambient image sensor. Do
not touch the sensor lens that is located
on the ambient image sensor.

LIC5121

LSD3484

2-68

Instruments and controls

If the ambient image sensor is damaged
due to an accident, it is recommended that
you visit a NISSAN dealer.

Battery saver system

If the ignition switch is placed in the OFF
position while the headlight switch is in the

position, the headlights will

turn off after a period of time.

CAUTION

Even though the battery saver feature
automatically turns off the headlights
after a period of time, you should turn
the headlight switch to the AUTO or OFF
position when the engine is not run-
ning to avoid discharging the vehicle
battery.

LED DAYTIME RUNNING LIGHTS
(DRL) SYSTEM

The LED DRL automatically illuminate at
100% intensity when the engine is started
and the parking brake released. The LED
Daytime Running Lights (DRL) operate with
the headlight switch in any position. When
you turn the headlight switch to the
position for full illumination, the LED DRL
illuminate at a lower intensity.

If the parking brake is applied before the
engine is started, the LED DRL do not illumi-
nate. The LED DRL illuminate when the
parking brake is released. The LED DRL will
remain on until the ignition switch is placed
in the OFF position.

At dusk, the headlights, interior controls
and switches will automatically illuminate
if the headlight switch is in the AUTO
position.

WARNING

When the LED DRL system is active, tail
lights on your vehicle are not on. It is
necessary at dusk to turn on your head-
lights. Failure to do so could cause an
accident injuring yourself and others.

INSTRUMENT BRIGHTNESS
CONTROL

Press the “+” button to increase the bright-
ness of instrument panel lights.

Press the “-” button to decrease the bright-
ness of instrument panel lights.

LIC4691

Instruments and controls

2-69

TURN SIGNAL SWITCH

Turn signal

䊊

Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signal cancels auto-
matically.

Lane change signal

䊊

Move the lever up or down until the turn
signal begins to flash, but the lever
does not latch, to signal a lane change.
Hold the lever until the lane change is
completed.

Move the lever up or down until the turn
signal begins to flash, but the lever does
not latch, and release the lever. The turn
signal will automatically flash three times.

Choose the appropriate method to signal
a lane change based on road and traffic
conditions.

NOTE:

The 3 flash pass feature may be disabled.
For additional information, see “Vehicle
information

display-5

inch

(13

cm)

Type A” (P. 2-20) or “Vehicle information
display-7 inch (18 cm) Type B” (P. 2-39).

To sound the horn, push near the horn icon
on the steering wheel.

WARNING

Do not disassemble the horn. Doing so
could affect proper operation of the
supplemental front air bag system.
Tampering

with

the

supplemental

front air bag system may result in seri-
ous personal injury.

LIC5122

LIC3568

HORN

2-70

Instruments and controls

WARNING

Do not use or allow occupants to use
the seat heater if you or the occupants
cannot monitor elevated seat tem-
peratures or have an inability to feel
pain in body parts that contact the
seat. Use of the seat heater by such
people could result in serious injury.

CAUTION

•

The battery could run down if the
seat heater is operated while the en-
gine is not running.

•

Do not use the seat heater for ex-
tended periods or when no one is us-
ing the seat.

•

Do not put anything on the seat
which insulates heat, such as a blan-
ket, cushion, seat cover, etc. Other-
wise, the seat may become over-
heated.

•

Do not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the heater.

•

Any liquid spilled on the heated seat
should be removed immediately with
a dry cloth.

•

When cleaning the seat, never use
gasoline, benzine, thinner, or any
similar materials.

•

If any malfunctions are found or the
heated seat does not operate, turn
the switch off and have the system
checked. It is recommended that you
visit a NISSAN dealer for this service.

The front seats are warmed by built-in
heaters.

1. Place the ignition switch in the ON

position.

2. Push the switch until either two lights

are illuminated for high setting, or one
light is illuminated for low setting.

The heater is controlled by a thermostat,
automatically turning the heater on and
off. The indicator light will remain on as
long as the switch is on.

3. When the seat is warmed or before you

leave the vehicle, be sure to push the
switch to turn it off.

LIC4904

HEATED SEAT SWITCHES (if so
equipped)

Instruments and controls

2-71

Push the heated steering wheel switch to
warm the steering wheel after the ignition
switch is placed in the ON position. The
indicator light will come on.

If the surface temperature of the steering
wheel is below 68°F (20°C), the system will
heat the steering wheel and cycle off and
on to maintain a temperature above 68°F
(20°C). The indicator light will remain on as
long as the system is on.

Push the switch again to turn the heated
steering wheel system off manually. The
indicator light will go off.

NOTE:
• Once activated, your heated steering

wheel will automatically turn on and
off to maintain a temperature above
68°F (20°C).

• When the temperature of the steering

wheel is above 122°F (50°C) and the
heated steering wheel switch is turned
on, the system will not heat the steer-
ing wheel. This does not indicate a
malfunction.

The Steering Assist switch is used to en-
able and disable the Steering Assist sys-
tem that is activated using the settings
menu of the vehicle information display.

The Steering Assist system controls the
steering system, when ProPILOT Assist is
engaged, to help keep your vehicle near
the center of the lane when driving. For
additional information, see ”ProPILOT As-
sist” (P. 5-69) and “Intelligent Lane Interven-
tion (I-LI)” (P. 5-39).

LIC4030

LIC4101

HEATED STEERING WHEEL SWITCH (if
so equipped)

STEERING ASSIST SWITCH (for
vehicles with ProPILOT Assist) (if so
equipped)

2-72

Instruments and controls

EMERGENCY SUPPORT

NissanConnect® Services provide various
services to support dealing with emergen-
cies of the subscribed vehicle and the
driver.

For example, in case of an illness or serious
injury, you can seek support by pressing
the in-vehicle Emergency Call (SOS) button
and connecting to the NissanConnect® Ser-
vices Response Center. The NissanConnect®
Services Response Center can specify the
location of the vehicle via GPS, and the infor-
mation will be sent to the police or other
agencies as needed.

For information about other NissanConnect®
Services emergency support related ser-
vices, contact the NissanConnect® Cus-
tomer Support line at 1–855–426–6628 or
refer to the NissanConnect® Services web-
site www.nissanusa.com/connect (for U.S.)
or www.nissan.ca/nissanconnect (English) /
www.nissan.ca/nissanconnect/fr (French) (for
Canada).

WARNING

•

Please note that the Automatic Colli-
sion Notification service and Emer-
gency Call function cannot be used in
the following conditions:

–

Emergency functions and services
will not be available without a paid
subscription

NissanConnect®

Services.

–

The NissanConnect® Services net-
work system is disabled.

–

The vehicle moves outside the
service

area

where

the

TCU

(Telematics Control Unit) is con-
nected to the system.

–

The vehicle is outside the area
where the cellular network service
is receivable.

–

The vehicle is in a location with
poor signal reception such as tun-
nels, underground parking ga-
rages,

behind

buildings

mountainous areas.

–

The line is busy.

–

The TCU (Telematics Control Unit)
or other systems of your vehicle
are not working properly.

–

It may not be possible to make
an emergency call depending on
the severity of a collision and/or
emergency.

•

Park the vehicle in a safe location and
set the parking brake before operat-
ing the Emergency Call (SOS) button.

•

Only use this service in case of an
emergency. There may be a penalty
for inappropriate use of the service.

•

Radio waves could adversely affect
electric medical equipment. Indi-
viduals who use a pacemaker should
contact the device manufacturer re-
garding any possible effects before
using the system.

•

The TCU (Telematics Control Unit) an-
tenna is installed inside the upper
central part of the instrument panel.
An occupant should not get any
closer to the antenna than specified
by the pacemaker manufacturer. The
radio waves from the TCU antenna
may adversely affect the operation
of the pacemaker while using the
NissanConnect® Services.

EMERGENCY CALL (SOS) BUTTON (if so
equipped)

Instruments and controls

2-73

Making an emergency call

The Emergency Call (SOS) button

is un-

der a cover and is located near the map
light.

1. Press the Emergency Call (SOS) button

to make an emergency call.

2. When the line is connected, speak to the

Response Specialist.

If you want to cancel the emergency call,
press and hold the Emergency Call (SOS)
button for a few seconds.

NOTE:

•

After the Emergency Call (SOS) button
is pressed, it may take some time until
the system initiates connection, de-
pending on the technical environment
and whether the TCU (Telematics Con-
trol Unit) is being used by the other
services.

•

An indicator light on the Emergency
call (SOS) button shows the readiness
of the emergency support system. If
the indicator light is not illuminated,
pressing the Emergency Call (SOS)
button does not connect your vehicle
to the Response Specialist. The indica-
tor light blinks while connected to the
NissanConnect®

Services

Response

Center.

•

Even when the indicator light is illumi-
nated, connection to the NissanConnect®
Services Response Center may not be
possible. If this occurs in an emergency
situation, contact the authorities by other
means.

•

To avoid disconnecting the line, keep
the engine running during an emer-
gency call, if it is safe to do so.

LIC4213

2-74

Instruments and controls

Nissan Altima (2024 year). Manual in english - page 5