Content .. 275 276 277 278 ..

Juke F15 (2012 year). Service Repair Manual - part 277

ENGINE OIL

LU-27

< PERIODIC MAINTENANCE >

[HR16DE]

• Always use oil level gauge to determine the proper amount of engine oil in the engine.

Warm up engine and check area around drain plug and oil filter for engine oil leakage.

Stop engine and wait for 10 minutes.

Check the engine oil level. Refer to

LU-25, "Inspection"

LU-28

< PERIODIC MAINTENANCE >

[HR16DE]

OIL FILTER

OIL FILTER

Removal and Installation

INFOID:0000000006450024

REMOVAL

Remove engine under cover.

Using oil filter wrench [SST: KV10115801] (A), remove oil filter.

CAUTION:

• Oil filter is provided with relief valve. Use genuine NISSAN

oil filter or equivalent.

• Be careful not to get burned when engine and engine oil

may be hot.

• When removing, prepare a shop cloth to absorb any

engine oil leakage or spillage.

• Completely wipe off any engine oil that adheres to engine

and vehicle.

INSTALLATION

Remove foreign materials adhering to the oil filter installation surface.

Apply new engine oil to the oil seal contact surface of new oil fil-
ter.

Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to specification.

Inspection

INFOID:0000000006450025

INSPECTION AFTER INSTALLATION

Check the engine oil level. Refer to

LU-25, "Inspection"

Start the engine, and check that there is no leakage of engine oil.

Stop the engine and wait for 10 minutes.

Check the engine oil level, and adjust the level. Refer to

LU-25, "Inspection"

: Vehicle front

PBIC3818E

SMA010

Oil filter:

: 17.7 N·m (1.8 kg-m, 13 ft-lb)

JPBIA0077ZZ

SERVICE DATA AND SPECIFICATIONS (SDS)

LU-29

< SERVICE DATA AND SPECIFICATIONS (SDS)

[HR16DE]

SERVICE DATA AND SPECIFICATIONS (SDS)

Periodical Maintenance Specification

INFOID:0000000006450026

ENGINE OIL CAPACITY (APPROXIMATE)

Unit:

(US qt, lmp qt)

Engine Oil Pressure

INFOID:0000000006450027

Unit: kPa (kg/cm

, psi)

*: Engine oil temperature at 80

C (176

Drain and refill

With oil filter change

4.3 (4-4/8, 3-6/8)

Without oil filter change

4.1 (4-3/8, 3-5/8)

Dry engine (Overhaul)

4.8 (5-1/8, 4-2/8)

Engine speed

Approximate discharge pressure*

Idle speed

60 (0.61, 9)

2,000 rpm

270 (2.8, 39)

LU-30

< PRECAUTION >

[K9K]

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Liquid Gasket

INFOID:0000000006450028

REMOVAL OF LIQUID GASKET

• After removing mounting nuts and bolts, separate the mating sur-

face using the seal cutter [SST: KV10111100] (A) and remove old
liquid gasket sealing.

CAUTION:

Be careful not to damage the mating surfaces.

• Tap the seal cutter [SST: KV10111100] to insert it (B), and then

slide it (C) by tapping on the side as shown in the figure.

• In areas where the seal cutter [SST: KV10111100] is difficult to use,

lightly tap the parts using a plastic hammer to remove it.

CAUTION:

If for some unavoidable reason tool such as a screwdriver is
used, be careful not to damage the mating surfaces.

LIQUID GASKET APPLICATION PROCEDURE

Using a scraper (A), remove old liquid gasket adhering to the liq-
uid gasket application surface and the mating surface.
• Remove liquid gasket completely from the groove of the liquid

gasket application surface, mounting bolts, and bolt holes.

Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.

Attach liquid gasket tube to the tube presser (commercial ser-
vice tool).
Use Liquid Gasket or equivalent.

Apply liquid gasket without gaps to the specified location accord-
ing to the specified dimensions.
• If there is a groove for liquid gasket application, apply liquid

gasket to the groove.

• As for bolt holes (B), normally apply liquid gasket inside the

holes. Occasionally, it should be applied outside the holes.
Check to read the text of this manual.

• Within five minutes of liquid gasket application, install the mat-

ing component.

• If liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill

engine oil and engine coolant.

CAUTION:

JPBIA0052ZZ

JPBIA0053ZZ

EMA0622D

: Groove

: Inside

JPBIA0010ZZ

PRECAUTIONS

LU-31

< PRECAUTION >

[K9K]

If there are specific instructions in this manual, observe them.

LU-32

< PREPARATION >

[K9K]

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000006450029

NISSAN tool number
(RENAULT tool number)
Tool name

Description

KV113C0010
(Mot.1329)
Oil filter wrench

Removing and installing oil filter

KV113E0020
(Mot.836-05)
Oil pressure gauge set

Measuring oil pressure
Use C, E, F.

WS39930000
( — )
Tube presser

Pressing the tube of liquid gasket

MBIB0369E

MBIB0663E

S-NT052

ENGINE OIL

LU-33

< PERIODIC MAINTENANCE >

[K9K]

PERIODIC MAINTENANCE

ENGINE OIL

Inspection

INFOID:0000000006450030

OIL LEVEL AND MUDDINESS

• Before starting the engine, check the oil level placing vehicle hori-

zontally. If the engine is already started, stop it and allow 10 min-
utes before checking.

• Make sure the oil level is within the range shown in the figure.
• If it is out of range, adjust it.

ENGINE OIL APPEARANCE

• Check engine oil for white turbidity or heavy contamination.
• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.

Repair or replace damaged parts.

OIL LEAKAGE

Check for oil leakage around the following area.
• Oil pan
• Oil pan drain plug
• Oil pressure switch
• Oil filter bracket
• Vacuum pump
• Oil pump housing
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head and rocker cover
• Oil cooler
• Crankshaft oil seals

OIL PRESSURE CHECK

WARNING:

• Be careful not to burn yourself, as the engine oil is hot.
• Oil pressure check should be done in Neutral “N” position.

Check the oil level. Refer to “OIL LEVEL MUDDINES“.

Remove engine undercover.

Disconnect harness connector at oil pressure switch (1), and
remove oil pressure switch using a deep socket (commercial
service tool).

CAUTION:

Never drop or shock oil pressure switch.

Install oil pressure gauge [SST:KV113E0020 (Mot. 836-05)]

After warming up the engine, make sure oil pressure corresponding to the engine speed is produced.

MBIB0548E

: Oil pan

: Vehicle front

JPBIA3089ZZ

Engine oil pressure

: Refer to

LU-39, "Standard and Limit"

LU-34

< PERIODIC MAINTENANCE >

[K9K]

ENGINE OIL

After checking, install the oil pressure switch as follows.

Remove old liquid gasket adhering to the switch and engine.

Apply liquid gasket and tighten oil pressure switch to specification.
Use Genuine Liquid Gasket or equivalent.

Start engine and check for oil leakage.

Draining

INFOID:0000000006450031

WARNING:

• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin

contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.

Warm up the engine, and check for engine oil leakage from engine components. Refer to

LU-25, "Inspec-

tion"

Stop the engine and wait for 10 minutes.

Loosen oil filler cap.

Remove drain plug and then drain engine oil.

Refilling

INFOID:0000000006450032

Refill with new engine oil.
Engine oil specification and viscosity: Refer to

MA-13, "Fluids and Lubricants"

CAUTION:

• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-

tions for reference only.

• Always use oil level gauge to determine the proper amount of engine oil in the engine.

Warm up engine and check area around drain plug and oil filter for engine oil leakage.

Stop engine and wait for 10 minutes.

Check the engine oil level. Refer to

LU-33, "Inspection"

Tightening torque

: Refer to

LU-35, "Exploded View"

Engine oil capacity

: Refer to

LU-39, "Standard and Limit"

OIL FILTER

LU-35

< PERIODIC MAINTENANCE >

[K9K]

OIL FILTER

Exploded View

INFOID:0000000006450033

Removal and Installation

INFOID:0000000006450034

REMOVAL

Using an oil filter wrench [SST:KV113C0010 (Mot.1329)] (A)
remove oil filter.

CAUTION:

• Be careful not to get burned when the engine and engine oil

are hot.

• When removing, prepare a shop cloth to absorb any oil leak-

age or spillage.

• Never allow engine oil to adhere to the drive belts.
• Completely wipe off any oil that adhere to the engine and the

vehicle.

INSTALLATION

Remove foreign materials adhering to the oil filter installation surface.

Install oil filter bracket to oil cooler.

CAUTION:

Install oil filter bracket, positioning lug in the hole of oil cooler.

Apply engine oil to the oil seal contact surface of the new oil fil-
ter.

Install the oil filter until it comes into contact with the oil seal on
the engine bracket.

Tighten the oil filter three-quarters of a turn by hand.

After warming up the engine, check for engine oil leakage.

Check oil level and add engine oil. Refer to

LU-33

E1BIA0012GB

O-ring

Oil filter bracket

Oil pressure switch

Oil filter

O-ring

Connecting bolt

To oil cooler

: N·m (kg-m, ft-lb)

: Always replace after every disassembly.

JPBIA3090ZZ

SMA010

LU-36

< REMOVAL AND INSTALLATION >

[K9K]

OIL PUMP

REMOVAL AND INSTALLATION

OIL PUMP

Exploded View

INFOID:0000000006450035

Removal and Installation

INFOID:0000000006450036

REMOVAL

Disconnect the battery cable from the negative terminal.

Remove engine under cover.

Remove front wheel RH. Refer to

WT-7, "Exploded View"

Remove fender protector RH. Refer to

EXT-22, "Exploded View"

Remove drive belt. Refer to

EM-276, "Removal and Installation"

Remove oil pan. Refer to

EM-288, "Exploded View"

Remove rear oil seal retainer. Refer to

EM-302, "Exploded View"

Remove oil pump drive chain. Refer to

EM-330, "Disassembly and Assembly"

Remove oil pump assembly.

INSTALLATION

Install in the reverse order of removal paying attention to the following.

Rear Oil Seal Retainer and Oil Pump

• Refer to

EM-330, "Disassembly and Assembly"

MBIB0552E

Oil pump drive chain

Crankshaft sprocket

Oil pump assembly

OIL COOLER

LU-37

< REMOVAL AND INSTALLATION >

[K9K]

OIL COOLER

Exploded View

INFOID:0000000006450037

CAUTION:

• Be careful not to get burned when the engine and engine oil are hot.
• When removing, prepare a shop cloth to absorb any oil leakage or spillage.
• Completely wipe off any oil that abhere to the engine and the vehicle.

Removal and Installation

INFOID:0000000006450038

REMOVAL

Drain engine coolant. Refer to

CO-62, "Draining"

CAUTION:

Perform when engine is cold.

Remove oil filter and oil filter bracket. Refer to

LU-35, "Exploded View"

Remove alternator.

Remove oil cooler.

INSTALLATION