Juke F15 (2012 year). Service Repair Manual - part 87

DLK-384, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006607732

CHECK BACK DOOR OPEN INPUT SIGNAL

Turn ignition switch OFF.

Disconnect back door opener switch connector.

Check signal between back door opener switch harness connector and ground using oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

>> GO TO 2.

CHECK BACK DOOR OPENER SWITCH CIRCUIT

Disconnect BCM connector.

Check continuity between BCM harness connector and back door opener switch harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

>> Repair or replace harness.

Monitor item

Condition

Status

TRNK OPNR SW

Back door opener switch

Pressed

Released

OFF

(+)

(–)

Signal

(Reference value)

Back door opener switch

Connector

Terminal

D107

Ground

JPMIA0012GB

BCM

Back door opener switch

Continuity

Connector

Terminal

Connector

Terminal

M65

D107

Existed

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

BACK DOOR OPENER SWITCH

DLK-385

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DLK

CHECK BACK DOOR OPENER SWITCH GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace harness.

CHECK BACK DOOR OPENER SWITCH

DLK-385, "Component Inspection"

Is the inspection result normal?

YES

>> GO TO 5.

>> Replace back door opener switch.

CHECK INTERMITTENT INCIDENT

>> INSPECTION END

Component Inspection

INFOID:0000000006607733

CHECK BACK DOOR OPENER SWITCH

Turn ignition switch OFF.

Disconnect back door opener switch connector.

Check continuity between back door opener switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace back door opener switch.

Back door opener switch

Ground

Continuity

Connector

Terminal

D107

Existed

Back door opener switch

Condition

Continuity

Terminal

Back door opener
switch

Pressed

Existed

Released

Not existed

D L K - 3 8 6

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DOOR LOCK ACTUATOR

DOOR LOCK ACTUATOR

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000006607737

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock actuator is OK.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000006607738

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

Turn ignition switch OFF.

Disconnect front door lock assembly (driver side) connector.

Check voltage between front door lock assembly (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front door lock assembly (driver side).

>> GO TO 2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

Disconnect BCM connector and all door lock assembly connector.

Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness.

Monitor item

Status

DOOR LOCK

ALL LOCK

Door lock actuators

LOCK

ALL UNLK

UNLOCK

(+)

(–)

Condition

Voltage

(Approx.)

Front door lock assembly

(driver side)

Connector

Terminal

D13

Ground

Door lock and unlock switch

Unlock

12 V

Lock

BCM

Front door lock assembly (driver side)

Continuity

Connector

Terminal

Connector

Terminal

M66

D13

Existed

BCM

Ground

Continuity

Connector

Terminal

M66

Not existed

DOOR LOCK ACTUATOR

DLK-387

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DLK

CHECK BCM OUTPUT SIGNAL

Connect BCM connector.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

>> Replace BCM. Refer to

PASSENGER SIDE

PASSENGER SIDE : Component Function Check

INFOID:0000000006607739

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock actuator is OK.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000006607740

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

Turn ignition switch OFF.

Disconnect front door lock assembly (passenger side) connector.

Check voltage between front door lock assembly (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front door lock assembly (passenger side).

>> GO TO 2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

Disconnect BCM connector and all door lock assembly connector.

Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M66

Ground

Door lock and unlock switch

Unlock

12 V

Lock

Monitor item

Status

DOOR LOCK

ALL LOCK

Door lock actuators

LOCK

ALL UNLK

UNLOCK

(+)

(–)

Condition

Voltage

(Approx.)

Front door lock assembly

(passenger side)

Connector

Terminal

D30

Ground

Door lock and unlock switch

Unlock

12 V

Lock

DLK-388

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DOOR LOCK ACTUATOR

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness.

CHECK BCM OUTPUT SIGNAL

Connect BCM connector.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

>> Replace BCM. Refer to

REAR LH

REAR LH : Component Function Check

INFOID:0000000006607741

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock actuator is OK.

REAR LH : Diagnosis Procedure

INFOID:0000000006607742

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

Turn ignition switch OFF.

Disconnect rear door lock assembly LH connector.

Check voltage between rear door lock assembly LH harness connector and ground.

BCM

Front door lock assembly (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M66

D30

Existed

BCM

Ground

Continuity

Connector

Terminal

M66

Not existed

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M66

Ground

Door lock and unlock switch

Unlock

12 V

Lock

Monitor item

Status

DOOR LOCK

ALL LOCK

Door lock actuators

LOCK

ALL UNLK

UNLOCK

DOOR LOCK ACTUATOR

DLK-389

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DLK

Is the inspection result normal?

YES

>> Replace rear door lock assembly LH.

>> GO TO 2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

Disconnect BCM connector and all door lock assembly connector.

Check continuity between BCM harness connector and rear door lock assembly LH harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness.

CHECK BCM OUTPUT SIGNAL

Connect BCM connector.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

>> Replace BCM. Refer to

REAR RH

REAR RH : Component Function Check

INFOID:0000000006607743

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

Check that the function operates normally according to the following conditions.

(+)

(–)

Condition

Voltage

(Approx.)

Rear door lock assembly LH

Connector

Terminal

D66

Ground

Door lock and unlock switch

Unlock

12 V

Lock

BCM

Rear door lock assembly LH

Continuity

Connector

Terminal

Connector

Terminal

M66

D66

Existed

BCM

Ground

Continuity

Connector

Terminal

M66

Not existed

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M66

Ground

Door lock and unlock switch

Unlock

12 V

Lock

Monitor item

Status

DOOR LOCK

ALL LOCK

Door lock actuators

LOCK

ALL UNLK

UNLOCK

DLK-390

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DOOR LOCK ACTUATOR

Is the inspection result normal?

YES

>> Door lock actuator is OK.

REAR RH : Diagnosis Procedure

INFOID:0000000006607744

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

Turn ignition switch OFF.

Disconnect rear door lock assembly RH connector.

Check voltage between rear door lock assembly RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear door lock assembly RH.

>> GO TO 2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

Disconnect BCM connector and all door lock assembly connector.

Check continuity between BCM harness connector and rear door lock assembly RH harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness.

CHECK BCM OUTPUT SIGNAL

Connect BCM connector.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

>> Replace BCM. Refer to

(+)

(–)

Condition

Voltage

(Approx.)

Rear door lock assembly RH

Connector

Terminal

D46

Ground

Door lock and unlock switch

Unlock

12 V

Lock

BCM

Rear door lock assembly RH

Continuity

Connector

Terminal

Connector

Terminal

M66

D46

Existed

BCM

Ground

Continuity

Connector

Terminal

M66

Not existed

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M66

Ground

Door lock and unlock switch

Unlock

12 V

Lock

DOOR LOCK AND UNLOCK SWITCH

DLK-391

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DLK

DOOR LOCK AND UNLOCK SWITCH

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000006607745

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock and unlock switch is OK.

DLK-391, "DRIVER SIDE : Diagnosis Procedure"

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000006607746

CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL

Turn ignition switch OFF.

Disconnect power window main switch connector.

Check signal between power window main switch harness connector and ground using oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

>> GO TO 2.

CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT

Disconnect BCM connector and front power window switch (passenger side) connector.

Check continuity between BCM harness connector and power window main switch harness connector.

Check continuity between BCM harness connector and ground.

Monitor item

Condition

Status

CDL LOCK SW

Door lock and unlock switch

Lock

Unlock

OFF

CDL UNLOCK SW

Lock

OFF

Unlock

(+)

(–)

Signal

(Reference value)

Power window main switch

Connector

Terminal

Ground

1.0 - 1.5 V

JPMIA0012GB

BCM

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

M65

Existed

DLK-392

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DOOR LOCK AND UNLOCK SWITCH

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-93, "Removal and Installation"

>> Repair or replace harness.

CHECK DOOR LOCK AND UNLOCK SWITCH GROUND

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace harness.

CHECK DOOR LOCK AND UNLOCK SWITCH

DLK-392, "DRIVER SIDE : Component Inspection"

Is the inspection result normal?

YES

>> GO TO 5.

>> Replace power window main switch. Refer to

PWC-44, "Removal and Installation"

CHECK INTERMITTENT INCIDENT

>> INSPECTION END

DRIVER SIDE : Component Inspection

INFOID:0000000006607747

CHECK DOOR LOCK AND UNLOCK SWITCH

Turn ignition switch OFF.

Disconnect power window main switch connector.

Check continuity between power window main switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace power window main switch.

PASSENGER SIDE

PASSENGER SIDE : Component Function Check

INFOID:0000000006607748

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

Power window main switch

Ground

Continuity

Connector

Terminal

Existed

Power window main switch

Condition

Continuity

Terminal

Door lock and unlock
switch

LOCK

Existed

UNLOCK

Not existed

LOCK

Not existed

UNLOCK

Existed

DOOR LOCK AND UNLOCK SWITCH

DLK-393

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DLK

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock and unlock switch is OK.

DLK-393, "PASSENGER SIDE : Diagnosis Procedure"

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000006607749

CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL

Turn ignition switch OFF.

Disconnect front power window switch (passenger side) connector.

Check signal between front power window switch (passenger side) harness connector and ground using
oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

>> GO TO 2.

CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT

Disconnect BCM connector and power window main switch connector.

Check continuity between BCM harness connector and front power window switch (passenger side) har-
ness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

>> Repair or replace harness.

Monitor item

Condition

Status

CDL LOCK SW

Door lock and unlock switch

Lock

Unlock

OFF

CDL UNLOCK SW

Lock

OFF

Unlock

(+)

(–)

Signal

(Reference value)

Front power window switch (passenger side)

Connector

Terminal

D26

Ground

1.0 - 1.5 V

JPMIA0012GB

BCM

Front power window switch (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M65

D26

Existed

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

DLK-394

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DOOR LOCK AND UNLOCK SWITCH

CHECK DOOR LOCK AND UNLOCK SWITCH GROUND

Check continuity between front power window switch (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace harness.

CHECK DOOR LOCK AND UNLOCK SWITCH

DLK-394, "PASSENGER SIDE : Component Inspection"

Is the inspection result normal?

YES

>> GO TO 5.

>> Replace front power window switch (passenger side). Refer to

PWC-44, "Removal and Installa-

tion"

CHECK INTERMITTENT INCIDENT

>> INSPECTION END

PASSENGER SIDE : Component Inspection

INFOID:0000000006607750

CHECK DOOR LOCK AND UNLOCK SWITCH

Turn ignition switch OFF.

Disconnect front power window switch (passenger side) connector.

Check continuity between front power window switch (passenger side) terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace front power window switch (passenger side).

Front power window switch (passenger side)

Ground

Continuity

Connector

Terminal

D26

Existed

Front power window switch (passenger side)

Condition

Continuity

Terminal

Door lock and unlock
switch

LOCK

Existed

UNLOCK

Not existed

LOCK

Not existed

UNLOCK

Existed

DOOR LOCK STATUS INDICATOR

DLK-395

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DLK

DOOR LOCK STATUS INDICATOR

Component Function Check

INFOID:0000000006607751

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “DOOR LOCK IND” in “ACTIVE TEST” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock status indicator is OK.

DLK-395, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006607752

CHECK DOOR LOCK STATUS INDICATOR INPUT SIGNAL

Turn ignition switch OFF.

Disconnect door lock status indicator connector.

Check voltage between door lock status indicator harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> GO TO 2.

CHECK DOOR LOCK STATUS INDICATOR CIRCUIT

Disconnect BCM connector.

Check continuity between BCM harness connector and door lock status indicator harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

>> Repair or replace harness.

CHECK DOOR LOCK STATUS INDICATOR GROUND

Check continuity between door lock status indicator harness connector and ground.

Monitor item

Status

DOOR LOCK IND

Door lock status indicator

Turns ON

OFF

Turns OFF

(+)

(–)

Condition

Voltage

(Approx.)

Door lock status indicator

Connector

Terminal

M83

Ground

Door lock operation is accom-
plished

12 V

Any door is OPEN

0 V

BCM

Door lock status indicator

Continuity

Connector

Terminal

Connector

Terminal

M65

M83

Existed

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

DOOR SWITCH

DLK-397

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DLK

DOOR SWITCH

Component Function Check

INFOID:0000000006607734

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL”, “DOOR SW-RR”, “BACK DOOR SW” in
“DATA MONITOR” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door switch is OK.

DLK-397, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006607735

CHECK DOOR SWITCH INPUT SIGNAL

Turn ignition switch OFF.

Disconnect malfunctioning door switch connector.

Check signal between malfunctioning door switch harness connector and ground using oscilloscope.

Is the inspection result normal?

YES-1 >> Back door: GO TO 3.
YES-2 >> other door: GO TO 4.
NO

>> GO TO 2.

CHECK DOOR SWITCH CIRCUIT

Disconnect BCM connector.

Check continuity between door switch harness connector and BCM harness connector.

Monitor item

Condition

Status

DOOR SW-DR

Driver side door

Open

Closed

Off

DOOR SW-AS

Passenger side door

Open

Closed

Off

DOOR SW-RL

Rear door LH

Open

Closed

Off

DOOR SW-RR

Rear door RH

Open

Closed

Off

DOOR SW-BK

Back door

Open

Closed

Off

(+)

(–)

Signal

(Reference value)

Door switch

Connector

Terminal

Driver side

B34

Ground

7.0 - 8.0 V

Passenger side

B27

Rear LH

B71

Rear RH

B53

Back door

D106

PKIB4960J

DLK-398

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 3]

DOOR SWITCH

Check continuity between door switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

>> Repair or replace harness.

CHECK BACK DOOR SWITCH CIRCUIT

Check continuity between back door lock assembly harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace harness.

CHECK DOOR SWITCH

DLK-398, "Component Inspection"

Is the inspection result normal?

YES

>> GO TO 5.

>> Replace malfunctioning door switch.

CHECK INTERMITTENT INCIDENT