Content .. 83 84 85 86 ..

Juke F15 (2012 year). Service Repair Manual - part 85

DLK-352

< REMOVAL AND INSTALLATION >

[TYPE 2]

INSIDE KEY ANTENNA

LUGGAGE ROOM : Exploded View

INFOID:0000000006620620

LUGGAGE ROOM : Removal and Installation

INFOID:0000000006620621

REMOVAL

Remove the luggage floor finisher. Refer to

INT-29, "Exploded View"

Remove the inside key antenna (luggage room) (1) mounting
clip RH (A).

Disengage inside key antenna (luggage room) fixing clip using a
flat-bladed screwdriver (A), and then pull out forward the inside
key antenna (luggage room).

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Visually check the clips for deformation and damage during installation.
Replace with new ones if necessary.

Inside key antenna (luggage room)

Clip

: Do not reuse

JMKIA5576ZZ

JMKIA5577ZZ

JMKIA5578ZZ

OUTSIDE KEY ANTENNA

DLK-353

< REMOVAL AND INSTALLATION >

[TYPE 2]

DLK

OUTSIDE KEY ANTENNA

DRIVER SIDE

DRIVER SIDE : Removal and Installation

INFOID:0000000006620622

REMOVAL

Remove the driver side outside handle. Refer to

DLK-339, "OUTSIDE HANDLE : Removal and Installation"

INSTALLATION

Install in the reverse order of removal.

PASSENGER SIDE

PASSENGER SIDE : Removal and Installation

INFOID:0000000006620623

REMOVAL

Remove the passenger side outside handle. Refer to

DLK-339, "OUTSIDE HANDLE : Removal and Installa-

tion"

INSTALLATION

Install in the reverse order of removal.

REAR BUMPER

REAR BUMPER : Removal and Installation

INFOID:0000000006620624

REMOVAL

Remove the rear bumper fascia. Refer to

EXT-16, "Removal and Installation"

Remove the outside key antenna (rear bumper) (1) mounting
clip (A), then remove outside key antenna (rear bumper).

INSTALLATION

Install in the reverse order of removal.

JMKIA5580ZZ

DLK-354

< REMOVAL AND INSTALLATION >

[TYPE 2]

INTELLIGENT KEY WARNING BUZZER

INTELLIGENT KEY WARNING BUZZER

Removal and Installation

INFOID:0000000006620625

REMOVAL

Remove the Intelligent Key warning buzzer (1) mounting bolt
(A), and then remove the Intelligent Key warning buzzer.

INSTALLATION

Install in the reverse order of removal.

JMKIA5571ZZ

REMOTE KEYLESS ENTRY RECEIVER

DLK-355

< REMOVAL AND INSTALLATION >

[TYPE 2]

DLK

REMOTE KEYLESS ENTRY RECEIVER

Removal and Installation

INFOID:0000000006620626

REMOVAL

Remove the glove box assembly. Refer to

IP-13, "Removal and Installation"

Remove the remote keyless entry receiver (1) mounting bolt (A),
and then remove remote keyless entry receiver.

INSTALLATION

Install in the reverse order of removal.

JMKIA6084ZZ

DLK-356

< REMOVAL AND INSTALLATION >

[TYPE 2]

INTELLIGENT KEY BATTERY

INTELLIGENT KEY BATTERY

Removal and Installation

INFOID:0000000006620627

Release the lock knob at the back of the Intelligent Key and remove the mechanical key.

Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.

CAUTION:

• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,

immediately wipe it dry.

Replace the battery with new one.

Align the tips of the upper and lower parts, and then push them
together until it is securely closed.

CAUTION:

• When replacing battery, keep dirt, grease, and other for-

eign materials off the electrode contact area.

• After replacing the battery, check that all Intelligent Key

functions work normally.

PIIB6221E

Battery replacement

:Coin-type lithium battery
(CR2025)

PIIB6222E

APPLICATION NOTICE

DLK-357

< HOW TO USE THIS MANUAL >

[TYPE 3]

DLK

HOW TO USE THIS MANUAL

APPLICATION NOTICE

Information

INFOID:0000000006445319

Check the vehicle type to use the service information in this section.

Service information

Destination

Type 1

With Intelligent Key and super lock

Type 2

With Intelligent Key, without super lock

Type 3

Without Intelligent Key, with super lock

Type 4

Without Intelligent Key and super lock

DLK-358

< PRECAUTION >

[TYPE 3]

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000006635668

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.

The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by

the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution Necessary for Steering Wheel Rotation after Battery Disconnect

INFOID:0000000006635669

NOTE:
• Before removing and installing any control units, first turn the ignition switch to the LOCK position, then dis-

connect both battery cables.

• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both

battery cables.

• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.

If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.

For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.

PRECAUTIONS

DLK-359

< PRECAUTION >

[TYPE 3]

DLK

OPERATION PROCEDURE

Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.

Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)

Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.

Perform the necessary repair operation.

When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)

Perform self-diagnosis check of all control units using CONSULT-III.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000006635670

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Work

INFOID:0000000006445166

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operational.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

PIIB3706J

DLK-360

< PREPARATION >

[TYPE 3]

PREPARATION

PREPARATION

Commercial Service Tools

INFOID:0000000006445168

Tool name

Description

Engine ear

Locating the noise

Remover tool

Remove the clips, pawls, and metal clips

Power tool

SIIA0995E

PIIB7923J

PIIB1407E

COMPONENT PARTS

DLK-361

< SYSTEM DESCRIPTION >

[TYPE 3]

DLK

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

INFOID:0000000006445169

Component Description

INFOID:0000000006445170

Back door lock assembly

Front door lock assembly (driver
side)

Front door switch (driver side)

Power window main switch
(door lock/unlock switch)

Key switch

Combination meter

Door lock status indicator

Remote keyless entry receiver

BCM
Refer to

BCS-6, "BODY CONTROL

SYSTEM : Component Parts Loca-
tion"

(with Intelligent Key) or

BCS-

96, "BODY CONTROL SYSTEM :
Component Parts Location"

(without

Intelligent Key)

10. Power window switch (passenger

side) (door lock/unlock switch)

11.

Air bag diagnosis sensor unit
Refer to

SRC-7, "Component Parts

Location"

View with the glove box assembly re-
moved

JMKIA5928ZZ

Item

Function

Air bag diagnosis sensor unit

Transmits air bag signal to BCM.

Back door lock assembly

Opens the back door with the back door open signal from BCM.

DLK-362

< SYSTEM DESCRIPTION >

[TYPE 3]

COMPONENT PARTS

BCM

Controls the door lock system.

Combination meter

• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.

Door lock actuator

• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.

Door lock and unlock switch

Transmits door lock/unlock operation to BCM.

Door lock status indicator

• The door lock status indicates door lock status.
• The indicator illuminates when a lock operation is successful.

Door switch

Detects door open/close condition.

Keyfob

Transmits button operation to remote keyless entry receiver.

Key switch

Key switch detects that ignition key is inserted into the ignition key cylinder, and
then transmits the signal to BCM.

Remote keyless entry receiver

Receives keyfob operation and transmits to BCM.

Item

Function

POWER DOOR LOCK SYSTEM

DLK-363

< SYSTEM DESCRIPTION >

[TYPE 3]

DLK

POWER DOOR LOCK SYSTEM

System Diagram

INFOID:0000000006445177

System Description

INFOID:0000000006445178

DOOR LOCK FUNCTION

• The door lock and unlock switch (driver side) is build into power window main switch.
• The door lock and unlock switch (passenger side) is build into front power window switch (passenger side).
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are

locked.

• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors and

are unlocked.

• With the ignition key inserted in the door key cylinder on driver side, turning it to lock position, locks door lock

actuator of all doors.*

• With the ignition key inserted in the door key cylinder on driver side, turning it to unlock position, unlocks

door lock actuator of all doors.*

*1: If equipped.

AIR BAG INTERLOCK UNLOCK FUNCTION

When ignition switch is ON and BCM receives air bag signal, it operates automatically to unlock all doors. Air
bag diagnosis sensor unit sends the air bag signal to BCM.

OPERATION CONDITION

If all of the following conditions are satisfied, door lock and unlock operation is performed using the door lock/
unlock switch.

: While door lock and unlock switch is pressed in the lock direction during this state, combination meter buzzer sounds and warns.

: When this item becomes OK according to keyfob ID verification, door lock/unlock operation is allowed.

KEY REMINDER FUNCTION

• While ignition key is inserted in ignition key cylinder and driver door is open, door is not locked when door

lock and unlock switch is pressed in the lock direction. This prevents keyfob from being left in the vehicle.

JMKIA6002GB

Door lock and unlock switch operation

Operation condition

LOCK

• Ignition Key is removed from ignition key cylinder and closed driver

side door*

• Doors other than drivers door are closed*

• Door are not locked by keyfob*

• Door lock that is requested is not auto door lock*

• Super lock is releases

UNLOCK

Door are not locked by keyfob*

DLK-364

< SYSTEM DESCRIPTION >

[TYPE 3]

POWER DOOR LOCK SYSTEM

• While door lock and unlock switch is pressed in the lock direction, combination meter buzzer sounds and

warns.

DOOR LOCK STATUS INDICATOR OPERATION

The door lock status indicator indicates door lock status under the following condition. And the timer is running
to turn OFF the indicator.

: Steering lock is locked.

1 Minute Timer

A timer must be running to turn OFF the indicator. The timer runs for 1 minute after doors are locked by keyfob
or auto door lock.

30 Minute Timer

A timer must be running to turn OFF the indicator. The timer runs for 30 minutes after doors are locked by door
lock and unlock switch.

OVERRIDE FUNCTION

When inside handle of front door is operated while doors are in lock states, lock state of the applicable door
lock becomes invalid and the door is open.

UNLOCK LINK FUNCTION

When driver side door or passenger side door is opened, all doors are unlocked.
Unlock function operates when driver door or passenger door is open while all of the following conditions are
satisfied.

NOTE:
When anti-hijack function is activated, only the applicable door is unlocked.

AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)

The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as follows.

Vehicle Speed Sensing Auto Door Lock*1

All doors are locked when the vehicle speed reaches 10 km/h (6 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 10 km/h (6 MPH) or more.

P Range Interlock Door Lock*

All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P.

Setting change of Automatic Door Lock/Unlock Function

The lock operation setting of the automatic door lock/unlock function can be changed.

With CONSULT-III

Lock operation

Ignition position

Door state

Indicator operation

Door lock and unlock switch

All doors closed

Door lock and unlock switch

Any doors open

OFF

Door lock and unlock switch

ACC, OFF or LOCK*

All doors closed

ON (30 minute timer)

Keyfob/Auto door lock function

ACC, OFF or LOCK*

All doors closed

ON (1 minute timer)

Door lock and unlock switch

ACC, OFF or LOCK*

Driver doors open

→

All doors closed

OFF

→

ON (30 minute timer)

Keyfob

ACC, OFF or LOCK*

Any doors open

→

All doors closed

OFF

→

ON (1 minute timer)

Operation condition

• Doors are locked by door lock/unlock switch or automatic lock/unlock function
• Driver or passenger door switch is switched from OFF to ON
• Anti-hijack function is not activated
• Vehicle speed is 5 km/h (3 MPH) or less

POWER DOOR LOCK SYSTEM

DLK-365

< SYSTEM DESCRIPTION >

[TYPE 3]

DLK

The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT-III.

Without CONSULT- III

The automatic door lock function ON/OFF can be switched by performing the following operation.

Close all doors (door switch OFF)

Turn ignition switch ON

Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.

The switching is completed when the hazard warning lamp blinks.

AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)

The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 2 types as follows.

IGN OFF Interlock Door Unlock*1

All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.

P Range Interlock Door Unlock*

All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.

Key out Interlock Door Unlock

When ignition key is removed from ignition knob switch, all doors unlock.
When BCM detects that ignition key is removed from ignition knob switch, BCM transmits unlock signal to all
door lock actuators.

Setting change of Automatic Door Lock/Unlock Function

The unlock operation setting of the automatic door lock/unlock function can be changed.

With CONSULT- III

The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT-III.

Without CONSULT- III

The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.

Close all doors below (door switch OFF)

Turn ignition switch ON

Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.

The switching is completed when the hazard warning lamp blinks.

*1: This function is set to OFF before delivery.
*2: This function does not operate on M/T models.

OFF

→

: 2 blinks

→

OFF

: 1 blink

OFF

→

: 2 blinks

→

OFF

: 1 blink

DLK-366

< SYSTEM DESCRIPTION >

[TYPE 3]

REMOTE KEYLESS ENTRY SYSTEM

REMOTE KEYLESS ENTRY SYSTEM

REMOTE KEYLESS ENTRY FUNCTION

REMOTE KEYLESS ENTRY FUNCTION : System Diagram

INFOID:0000000006445179

REMOTE KEYLESS ENTRY FUNCTION : System Description

INFOID:0000000006445180

DOOR LOCK AND UNLOCK OPERATION

• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to

BCM via remote keyless entry receiver.

• When BCM receives the door lock and unlock signal, it operates door lock actuator, blinks the hazard lamp

at the same time as a reminder.

OPERATION CONDITION

If the following conditions are satisfied, door lock/unlock operation is performed if the keyfob is operated.

OPERATION AREA

To ensure that the keyfob works effectively, use within 100 cm (3 ft) range of each door, however the operable
range may differ according to surroundings.

ANTI-HIJACK FUNCTION

Information of super lock function with anti-hijack function.
Refer to

DLK-367, "SUPER LOCK FUNCTION : System Description"

HAZARD REMINDER OPERATION

When door is locked or unlocked by keyfob, then BCM blinks hazard warning lamp as a reminder.
NOTE:
Hazard reminder mode can be changed with CONSULT-III. Refer to

DLK-372, "MULTI REMOTE ENT : CON-

SULT-III Function (BCM - MULTI REMOTE ENT) (With Super Lock)"

JMKIA6005GB

Remote controller operation

Operation condition

Lock

• Key switch is off
• All doors are closed

Unlock

Key switch is off

REMOTE KEYLESS ENTRY SYSTEM

DLK-367

< SYSTEM DESCRIPTION >

[TYPE 3]

DLK

AUTO DOOR LOCK FUNCTION

After door is unlocked by keyfob button operation and if 30 seconds or more passes without performing the fol-
lowing operation, all doors are automatically locked. However, operation check function does not activate.

Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to

DLK-

371, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)"

INTERIOR ROOM LAMP CONTROL FUNCTION

Interior room lamp is controlled according to door lock/unlock state, refer to

INL-6, "INTERIOR ROOM LAMP

CONTROL SYSTEM : System Description"

SUPER LOCK FUNCTION

SUPER LOCK FUNCTION : System Diagram

INFOID:0000000006562689

SUPER LOCK FUNCTION : System Description

INFOID:0000000006562686

• Super lock provides a higher anti-theft performance than a conventional door lock function.
• BCM controls the super lock system.
• When all doors are closed super lock system can be set/release by keyfob.
• When super lock is set, inside handle of doors do not work.

SUPER LOCK SET OPERATION (LOCK OPERATION)

When Keyfob lock button is operated while all doors are in unlock state, super lock of all doors is set, and
simultaneously, all doors are locked.

SUPER LOCK RELEASE OPERATION (UNLOCK OERATION) WITH ANTI-HIJACK MODE

Hazard reminder setting

(With CONSULT-III)

Door lock operation

(with keyfob)

Hazard warning lamp blink

HAZARD LAMP SET

MODE 1

—

MODE 2

Lock

—

Unlock

Twice

Unlock (anti-hijack)

Twice (quick)

MODE 3

Lock

Once

Unlock

—

MODE 4

Lock

Once

Unlock

Twice

Unlock (anti-hijack)

Twice (quick)

Operating condition

• Door switch is ON (door is open)
• Door is locked
• Key switch is ON

JMKIA6013GB

Content .. 83 84 85 86 ..