Nissan Leaf (2024 year). Manual in english

The heated steering wheel system is de-
signed to operate only when the surface
temperature of the steering wheel is below
approximately 68°F (20°C).

Push the heated steering wheel switch to
warm the steering wheel when the power
switch is in the ACC or ON position.

If the surface temperature of the steering
wheel is below approximately 68°F (20°C),
the system will heat the steering wheel and
cycle off and on to maintain a temperature
above 68°F (20°C). The indicator light will
remain on as long as the system is on.

Push the switch again to turn the heated
steering wheel system off manually. The
indicator light turns off.

NOTE:
• If the surface temperature of the steer-

ing wheel is above 68°F (20°C) when the
switch is turned on, the system will not
heat the steering wheel. This is not a
malfunction.

• If the outside temperature is low (ap-

proximately 50°F (10°C) or less) and
the Climate Control Timer or Remote
Climate Control are used, the steering
wheel heater will automatically oper-
ate in the following conditions.

– When using the Climate Control

Timer: Operates from approximately
15 minutes before the set departure
time until the set departure time.

– When using Remote Climate Control:

Operates 15 minutes after Remote
Climate Control starts.

• The heated steering wheel consumes

less power than the heater and can be
used to either help extend vehicle range
by reducing heater use or to maximize
comfort by supplementing the heater.

The Emergency Call (SOS) system button is
used in combination with a NissanConnect®
Services powered by SiriusXM® subscription
to call for assistance in case of an emer-
gency.

Pressing the button will (with a paid sub-
scription) reach a Response Specialist that
will provide assistance based on the situa-
tion described by the vehicle’s occupant.
For additional information, or to enroll
your vehicle, refer to www.NissanUSA.com/
connect or call 855–426–6628.

LIC3804

LIC3913

HEATED STEERING WHEEL SWITCH
(if so equipped)

EMERGENCY CALL (SOS) BUTTON
(if so equipped)

2-58

Instruments and controls

To open the charge port lid, push the
charge port lid switch. For additional infor-
mation, see “Charge port lid” (P. 3-20).

To turn off the charge timer, push the im-
mediate charge switch. For additional in-
formation, see “Charging timer” (P. CH-43).

The dynamic driver assistance switch is
used to temporarily turn on and off the
Intelligent Lane Intervention (I-LI) and Intel-
ligent Blind Spot Intervention (I-BSI) sys-
tems that are activated using the settings
menu of the vehicle information display.

The I-LI and I-BSI systems must be turned
on with the dynamic driver assistance
switch every time the power switch is
placed in the ON position.

LIC3808

LCH2125

LIC4290

CHARGE PORT LID SWITCH

IMMEDIATE CHARGE SWITCH

DYNAMIC DRIVER ASSISTANCE
SWITCH (for vehicles without
ProPILOT Assist) (if so equipped)

Instruments and controls

2-59

The I-LI system warns the driver with a
warning and a chime, and helps assist the
driver to return the vehicle to the center of
the traveling lane by applying the brakes to
the left or right wheels individually (for a
short period of time). For additional infor-
mation, see “Intelligent Lane Intervention
(I-LI)” (P. 5-30) and “Vehicle information dis-
play” (P. 2-26).

The I-BSI system helps alert the driver of
other vehicles in adjacent lanes when
changing lanes, and helps assist the driver
to return the vehicle to the center of the
traveling lane. For additional information,
see “Intelligent Blind Spot Intervention (I-
BSI)” (P. 5-45).

The Steering Assist switch is used to en-
able and disable the Steering Assist sys-
tem that is activated using the settings
menu of the vehicle information display.

The Steering Assist system controls the
steering system, when ProPILOT Assist is
engaged, to help keep your vehicle near
the center of the lane when driving. For ad-
ditional information, see “ProPILOT Assist”
(P. 5-91) and “Intelligent Lane Intervention
(I-LI)” (P. 5-30).

The Rear Door Alert system functions un-
der certain conditions to indicate there
may be an object or passenger in the rear
seat(s). Check the seat(s) before exiting the
vehicle.

The Rear Door Alert system is initially dis-
abled. The driver can enable the system
using the vehicle information display. For
additional information, see “Vehicle infor-
mation display warnings and indicators”
(P. 2-34).

When the system is enabled:
• The system is activated when a rear door

is opened and closed within 10 minutes of
the vehicle being driven. When the driver
door is closed and the system is acti-
vated, a visual message appears in the
vehicle information display. For additional
information, see “Rear Door Alert is acti-
vated” (P. 2-35).

• If a rear door is opened and closed but

the vehicle is not driven within approxi-
mately 10 minutes, the system will not be
activated. A rear door must be opened
and closed and the car driven within 10
minutes for the system to activate.

LIC3932

STEERING ASSIST SWITCH (for models
with ProPILOT Assist) (if so equipped)

REAR DOOR ALERT

2-60

Instruments and controls

When the Rear Door Alert system is acti-
vated:
• When the driver puts the vehicle in the P

(Park) position, a notification message
appears in the vehicle information dis-
play with the options to “Dismiss Mes-
sage” or “Disable Alert” if desired.

– Select “Disable Alert” to temporarily dis-

able for that stop.

– No selection or ‘Dismiss Message” will

keep the alert enabled for that stop.

• If the alert is enabled when a driver exits

the vehicle, a message will appear in the
vehicle information display that states
“Check Rear Seat for All Articles.”

If “Horn & Alert” setting is selected:

–– An audible horn sound will occur after

a short time unless a rear door is
opened and closed within a short time
to deactivate the alert.

–– If the doors are locked before the alert

is deactivated by opening a rear door,
the horn will sound.

–– If the rear hatch is opened before a rear

door is opened, the horn will be delayed
until after the hatch is closed.

NOTE:

If “Alert Only” setting is selected, the
message alert will still be shown in the
vehicle information display but the horn
will not sound.

WARNING

•

If the driver selects “Disable Alert”, no
audible alert will be provided regard-
less of rear door open/close status.

•

There may be times when there is an
object or passenger in the rear
seat(s) but the audible alert does not
sound. For example, this may occur if
rear seat passengers enter or exit the
vehicle during a trip.

•

The system does not directly detect
objects or passengers in the rear
seat(s). Instead, it can detect when a
rear door is opened and closed, indi-
cating that there may be something
in the rear seat(s).

NOTE:
There may be times when the horn
sounds but there are no objects or pas-
sengers in the rear seat(s).

For additional information, see “Rear Door
Alert is activated” (P. 2-35).

CAUTION

•

The outlet and plug may be hot dur-
ing or immediately after use.

•

Do not use with accessories that ex-
ceed a 12-volt, 120W (10A) power draw.

•

Do not use double adapters or more
than one electrical accessory.

•

Use the power outlet with the power
switch is in the ON or READY to Drive
position to avoid discharging the 12-
volt battery.

LIC4291

POWER OUTLET

Instruments and controls

2-61

•

Avoid using the power outlet when
the air conditioner, headlights or rear
window defroster are on.

•

This power outlet is not designed for
use with a cigarette lighter unit.

•

Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.

•

Before inserting or disconnecting a
plug, make sure that the electrical
accessory being used is turned OFF.

•

When not in use, be sure to close the
cap. Do not allow water to contact
the outlet.

1. Type-A USB

There are USB/iPod® charging ports located
behind the center console. These ports will
charge compatible devices.

NOTE:
• Only the USB connection port located

below the instrument panel will allow
operation of the USB/iPod® devices
through the audio system.

• For best results, it is recommended to

use the manufacturer cables, which
are sold separately. A USB Type-C to
USB Type-A adapter could be available;
however, results may vary.

SEATBACK POCKET (if so equipped)

The seatback pockets may be located on
the driver’s and/or passenger seat. The
pocket can be used to store maps.

LIC5042

LIC0016

USB/iPod® CHARGING PORTS

STORAGE

2-62

Instruments and controls

WARNING

To ensure proper operation of the driv-
er’s and/or front passenger’s NISSAN Ad-
vanced Air Bag System (if so equipped),
please observe the following items:

•

Do not allow a passenger in the rear
seat to push or pull on the seatback
pocket or head restraint/headrest.

•

Do not place heavy loads heavier
than 9.1 lbs. (4 kg) on the seatback,
head restraint/headrest, or in the
seatback pocket.

STORAGE TRAY

WARNING

Do not place sharp objects in the tray(s)
to help prevent injury in an accident or
sudden stop.

GLOVE BOX

To open the glove box, pull the handle.

To close, push the lid in until it latches.

WARNING

Keep the glove box lid closed while
driving to prevent injury in case of an
accident or a sudden stop.

LIC4292

Instrument panel

LIC4349

Instruments and controls

2-63

CONSOLE BOX

To open the console box, pull up the lever
and pull up the lid. To close, push the lid
down until it is latched.

OVERHEAD SUNGLASSES STORAGE

To open the sunglasses holder, push and
release. Only store one pair of sunglasses
in the holder.

WARNING

Keep the sunglasses holder closed
while driving to avoid obstructing the
driver’s view and to help prevent an
accident.

CAUTION

•

Do not use for anything other than
sunglasses.

•

Do not leave sunglasses in the sun-
glasses holder while parking in direct
sunlight. The heat may damage the
sunglasses.

LIC3813

LIC2312

2-64

Instruments and controls

CUP HOLDERS

CAUTION

•

Avoid abrupt starting and braking
when the cup holder is being used
to prevent spilling the drink. If the
liquid is hot, it can scald you or your
passenger.

•

Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.

CAUTION

•

Do not use the bottle holder for any
other objects that could be thrown
about in the vehicle and possibly in-
jure people during sudden braking or
an accident.

•

Do not use the bottle holder for open
liquid containers.

LIC3810

Front

JVC0046X

Soft bottle holder (front)

LIC4978

Soft bottle holder (rear)

Instruments and controls

2-65

TONNEAU COVER (if so equipped)

WARNING

•

Never put anything on the tonneau
cover, no matter how small. Any ob-
ject on it could cause an injury in an
accident or sudden stop.

•

Do not leave the tonneau cover in the
vehicle with it disengaged from the
holder.

•

Properly secure all cargo with ropes or
straps to help prevent it from sliding
or shifting. Do not place cargo higher
than the seatbacks. In a sudden stop
or collision, unsecured cargo could
cause personal injury.

•

Properly secure cargo and do not al-
low it to contact the top tether strap
when it is attached to the top tether
anchor. Cargo that is not properly se-
cured or cargo that contacts the top
tether strap may damage the top
tether strap during a collision. If the
cargo cover contacts the top tether
strap when it is attached to the top
tether anchor, remove the cargo
cover from the vehicle or secure it on
the cargo floor below its attachment

location. If the cargo cover is not re-
moved, it may damage the top tether
strap during a collision. Your child
could be seriously injured or killed in
a collision if the child restraint top
tether strap is damaged.

The tonneau cover keeps the luggage
compartment contents hidden from the
outside.

To remove the tonneau cover:

䊊

Remove the straps from the rear hatch.

䊊

Pull up the tonneau cover.

LIC4293

2-66

Instruments and controls

䊊

Remove the tonneau cover holders
from the rear pillar.

䊊

Slide down the tonneau cover along
the rear seat back.

䊊

Remove the tonneau cover by pulling
either the left or right side backward
away from the pillar.

STOWING GOLF BAGS

Normally, two standard golf bags can be
stowed in the cargo area. Insert the top of
the golf bag into the right side of the cargo
area

then rotate the bag backward

Insert the top of the second golf bag into
right side of the cargo area

and stow

the bottom of golf bag forward all the way

In some cases, you may not be able to stow
two golf bags in your vehicle, depending on
their sizes or types.

POWER WINDOWS

WARNING

•

Make sure that all passengers have
their hands, etc. inside the vehicle
while it is in motion and before clos-
ing the windows. Use the window
lock switch to prevent unexpected
use of the power windows.

•

To help avoid risk of injury or death
through unintended operation of the
vehicle or its systems, including en-
trapment in windows or inadvertent
door lock activation, do not leave chil-
dren, people who require the assis-
tance of others, or pets unattended
in your vehicle. Additionally, the tem-
perature inside a closed vehicle on a
warm day can quickly become high
enough to cause a significant risk of
injury or death to people and pets.

The power windows operate when the
power switch is in the ACC or ON position,
or for about 45 seconds after the power
switch is placed in the OFF position. If the
driver’s or front passenger’s door is opened
during this period of about 45 seconds,
power to the windows is canceled.

LIC2497

LIC4294

WINDOWS

Instruments and controls

2-67

Main power window switch
(driver's side)

To open or close a window, push down

or pull up

the corresponding switch and

hold it. The main switches, on the driver's
side, will open or close all the windows.

Locking passengers' windows

When the lock button

is pushed in, only

the driver side window can be opened or
closed. Push it in again to cancel.

Passenger side power window
switch

The passenger's side power window switch
will open or close only the corresponding
window. To open or close the window, push
down or pull up the switch and hold it.

JVC0051X

1. Driver side automatic switch

2. Front passenger side switch

3. Rear left passenger side switch

4. Rear right passenger side switch

5. Window lock button

JVC0052X

2-68

Instruments and controls

Rear power window switch

The rear power window switches open or
close only the corresponding window. To
open the window, push the switch and
hold it down

. To close the window, pull

the switch up

Automatic operation

The automatic operation is available for
the switch that has an

mark on its

surface.

To fully open or close the window, com-
pletely push down or pull up the switch and
release it; the switch need not be held. The
window will automatically open or close all
the way. To stop the window, just push or lift
the switch in the opposite direction.

A light push or pull on the switch will cause
the window to open or close until the
switch is released.

Auto-reverse function

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the window.

If the control unit detects something
caught in the window as it is closing, the
window will be immediately lowered.

The auto reverse function can be activated
when the window is closed by automatic
operation when the power switch is in the
ON position or for 45 seconds after the
power switch is placed in the OFF position.

Depending on the environment or driv-
ing conditions, the auto reverse function
may be activated if an impact or load
similar to something being caught in the
window occurs.

LIC2663

JVC0053X

Instruments and controls

2-69

If the windows do not close
automatically

If the power window automatic function
(closing only) does not operate properly,
perform the following procedure to initial-
ize the power window system.

1. Place the power switch in the ON position.

2. Close the door.

3. Open the window completely by operat-

ing the power window switch.

4. Pull the power window switch and hold

it to close the window, and then hold
the switch more than 3 seconds after
the window is closed completely.

5. Release the power window switch. Op-

erate the window by the automatic
function to confirm the initialization is
complete.

If the power window automatic function
does not operate properly after performing
the procedure above, have your vehicle ser-
viced. It is recommended that you visit a
NISSAN certified LEAF dealer for this service.

The interior lights can be turned on

re-

gardless of door position. The lights will go
off after a period of time unless the power
switch is placed in the ON position when
any door is opened.

The interior lights can be set to operate
when the doors are opened

. To turn off

the interior lights when a is door open,
push the switch; the interior lights will not
illuminate, regardless of door position.

The lights will go off when the power switch
is placed in the ON position, or the driver’s
door is closed and locked. The lights will
also go off after a period of time when the
doors are open.

CAUTION

Do not use for extended periods of time
with the power switch in the OFF posi-
tion. This could result in a discharged
12-volt battery.

CONSOLE LIGHT (if so equipped)

The console light will turn on whenever the
parking lights or headlights are illuminated.

The console light brightness can be ad-
justed with the illumination brightness con-
trol in the vehicle information display.

LIC3814

INTERIOR LIGHTS

2-70

Instruments and controls

MAP LIGHTS

Press the button to turn the map lights on.
To turn them off, press the button again.

ROOM LIGHT

The room light switch has three positions:
ON, DOOR and OFF.

ON position

When the switch is in the ON position

the ceiling light will illuminate.

DOOR position

When the switch is in the DOOR position

the ceiling light will illuminate under the
following conditions:
• the power switch is placed in the LOCK

position

–– remains on for about 15 seconds.

• doors are unlocked by pushing the

UNLOCK

button or the request

switch, with the power switch in the LOCK
position

–– remains on for about 15 seconds.

• any door is opened and then closed with

the power switch in the LOCK position

–– remains on for about 15 seconds.

• any door is opened while the power

switch in the ACC or ON position

–– remains on while the door is opened.

When the door is closed, the light turns
off.

The light will automatically turn off after
10 minutes when the light remains illu-
minated to prevent the battery from be-
coming discharged.

OFF position

When the switch is in the OFF position

the ceiling light will not illuminate, regard-
less of the condition.

CARGO LIGHT

The light illuminates when the rear hatch is
opened. When the rear hatch is closed, the
light goes off. For additional information,
see “Exterior and interior lights” (P. 8-23).

LIC2304

SIC3513

Instruments and controls

2-71

NISSAN INTELLIGENT KEY®

Your vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key system com-
ponents and NISSAN Vehicle Immobilizer
System components.

As many as four Intelligent Keys can be
registered and used with one vehicle. The
new keys must be registered by a NISSAN
certified LEAF dealer prior to use with the
Intelligent Key system and NISSAN Vehicle
Immobilizer System of your vehicle. Since
the registration process requires erasing all
memory in the Intelligent Key components
when registering new keys, be sure to take
all Intelligent Keys that you have to the
NISSAN certified LEAF dealer.

A key number plate is supplied with your
keys. Record the key number and keep it in
a safe place (such as your wallet), not in the
vehicle. If you lose your keys, it is recom-
mended that you visit a NISSAN certified
LEAF dealer for duplicates by using the key
number. NISSAN does not record key num-
bers so it is very important to keep track of
your key number plate.

A key number is only necessary when you
have lost all keys and do not have one to
duplicate from. If you still have a key, it can
be duplicated without knowing the key
number.

CAUTION

Be sure to carry the Intelligent Key with
you when driving. The Intelligent Key is
a precision device with a built-in trans-
mitter. To avoid damaging it, please not
the following:

•

The Intelligent Key is water resistant;
however, wetting may damage the
Intelligent Key. If the Intelligent Key
gets wet, immediately wipe until it is
completely dry.

•

Do not bend, drop or strike it against
another object.

•

If the outside temperature is below
14°F (–10°C) degrees, the battery of
the Intelligent Key may not function
properly.

•

Do not place the Intelligent Key for an
extended period in an area where
temperatures exceed 140°F (60°C).

•

Do not change or modify the Intelli-
gent Key.

•

Do not use a magnet key holder.

•

Do not place the Intelligent Key near
an electric appliance such as a televi-
sion set, personal computer or cellu-
lar phone.

LPD3110

1. Intelligent Key (two sets)

2. Mechanical key

3. Key number plate (one plate)

KEYS

3-2

Pre-driving checks and adjustments

•

Do not allow the Intelligent Key to
come into contact with water or salt
water, and do not wash it in a wash-
ing machine. This could affect the
system function.

If an Intelligent Key is lost or stolen,
NISSAN recommends erasing the ID
code of that Intelligent Key. This will
prevent the Intelligent Key from unau-
thorized use to unlock the vehicle.
For information regarding the erasing
procedure, it is recommended that you
visit a NISSAN certified LEAF dealer.

Mechanical key

The Intelligent Key contains the mechani-
cal key.

To remove the mechanical key, release the
lock knob on the back of the Intelligent Key.

To install the mechanical key, firmly insert it
into the Intelligent Key until the lock knob
returns to the lock position.

Use the mechanical key to lock or unlock
the driver's door.

CAUTION

Always carry the mechanical key in-
stalled in the Intelligent Key slot.

For additional information, see “Locking
with key” (P. 3-5).

NISSAN VEHICLE IMMOBILIZER
SYSTEM KEYS

You can only drive your vehicle using the
master keys which are registered to the
NISSAN Vehicle Immobilizer System com-
ponents in your vehicle. These keys have a
transponder chip in the key head.

The master key can be used for all the locks.

To protect belongings when you leave a
key with someone, give them the Intelligent
Key only, not the mechanical key.

Never leave these keys in the vehicle.

Additional or replacement keys:

If you still have a key, the key number is not
necessary when you need extra NISSAN
Vehicle Immobilizer System keys. A NISSAN
certified LEAF dealer can duplicate your ex-
isting key. As many as four NISSAN Vehicle

SPA1951

Pre-driving checks and adjustments

3-3

Immobilizer System keys can be used with
one vehicle. You should bring all NISSAN
Vehicle Immobilizer System keys that you
have to the NISSAN certified LEAF dealer
for registration. This is because the regis-
tration process will erase the memory of all
key codes previously registered into the
NISSAN Vehicle Immobilizer System. After
the registration process, these compo-
nents will only recognize keys coded into
the NISSAN Vehicle Immobilizer System
during registration. Any virtual key acces-
sories (if so equipped) will also have to be
reregistered. Any key that is not given to the
dealer at the time of registration will no
longer be able to start your vehicle.

CAUTION

Do not allow the immobilizer system key,
which contains an electrical transpon-
der, to come into contact with water or
salt water. This could affect system func-
tion.

When the doors are locked using one of the
following methods, the doors cannot be
opened using the inside or outside door
handles. The doors must be unlocked to
open the doors.

WARNING

•

Always have the doors locked while
driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping to
prevent persons from being thrown
from the vehicle. This also helps keep
children and others from uninten-
tionally opening the doors, and will
help keep out intruders.

•

Before opening any door, always look
for and avoid oncoming traffic.

•

To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not leave
children, people who require the as-
sistance of others or pets unattended
in your vehicle. Additionally, the tem-
perature inside a closed vehicle on a
warm day can quickly become high
enough to cause a significant risk of
injury or death to people and pets.

DOORS

3-4

Pre-driving checks and adjustments

LOCKING WITH KEY

The power door lock system allows you to
lock or unlock all doors at the same time
using the master or mechanical key.

Turning the key toward the front

of the

vehicle locks all the doors and activates the
security system.

Turning the key 1 time toward the rear

the vehicle unlocks that door. From that
position, returning the key to neutral

(where the key can only be removed and
inserted) and turning it toward the rear

again within 5 seconds unlocks all doors.

LOCKING WITH INSIDE LOCK KNOB

To lock the door without the key, move the
inside lock knob to the lock position

then close the door.

To unlock the door without the key, move
the inside lock knob to the unlock position

LOCKING WITH POWER DOOR
LOCK SWITCH

To lock all the doors without a key, push the
door lock switch (driver's or front passen-
ger's side) to the lock position

. When

locking the door this way, be certain not to
leave the key inside the vehicle.

To unlock all the doors without a key, push
the door lock switch (driver's or front pas-
senger's side) to the unlock position

LPD0461

Driver's side

SPA2726

Inside lock

JVC0056X

Pre-driving checks and adjustments

3-5

Lockout protection

When any door is open and the power door
lock switch is moved to the lock position, all
doors will lock. If the Intelligent Key is left
in the vehicle after all the doors are closed,
all doors will unlock automatically and a
chime will sound.

These functions help to prevent the Intelli-
gent Key from being accidentally locked
inside the vehicle.

AUTOMATIC DOOR LOCKS

• All doors lock automatically when the

vehicle speed reaches 15 mph (24 km/h).

• All doors unlock automatically when the

power switch is placed in the OFF position.

CHILD SAFETY REAR DOOR LOCK

Child safety locks help prevent the rear
doors from being opened accidentally, espe-
cially when small children are in the vehicle.

The child safety lock levers are located on
the edge of the rear doors.

When the lever is in the unlock position

the door can be opened from the outside
or the inside.

When the lever is in the LOCK position

the door can be opened only from the
outside.

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the electric medical equipment manu-
facturer for the possible influences
before use.

•

The Intelligent Key transmits radio
waves when the buttons are pressed.
The FAA advises the radio waves may
affect aircraft navigation and com-
munication systems. Do not operate
the Intelligent Key while on an air-
plane. Make sure the buttons are not
operated unintentionally when the
unit is stored for a flight.

•

Never leave the Intelligent Key in the
vehicle when you leave the vehicle.

The Intelligent Key system can operate all
the door locks using the remote control
function or pushing the request switch on
the vehicle without taking the key out from
a pocket or purse. The operating environ-
ment and/or conditions may affect the
Intelligent Key system operation.

Be sure to read the following before using
the Intelligent Key system.

LPD2552

NISSAN INTELLIGENT KEY® SYSTEM

3-6

Pre-driving checks and adjustments

CAUTION

Be sure to carry the Intelligent Key with
you when operating the vehicle.

The Intelligent Key is capable of receiving
and transmitting radio waves. The Intelli-
gent Key system transmits weak radio
waves from various distances. Environ-
mental conditions may interfere with the
operation of the Intelligent Key system
under the following operating conditions:
• When operating near a location where

strong radio waves are transmitted, such
as a TV tower, power station and broad-
casting station.

• When in possession of wireless equip-

ment, such as a cellular telephone, trans-
ceiver or a CB radio.

• When the Intelligent Key is in contact with

or covered by metallic materials.

• When any type of radio wave remote con-

trol is used nearby.

• When the Intelligent Key is placed near an

electric appliance such as a personal
computer.

• When the vehicle is parked near a parking

meter.

In such cases, correct the operating condi-
tions before using the Intelligent Key func-
tion or use the mechanical key.

Although the life of the battery varies de-
pending on the operating conditions, the
battery’s life is approximately two years.
If the battery is discharged, replace it with a
new one.

When the Intelligent Key battery is low, the
“Key Battery Low” indicator illuminates in the
vehicle information display. For additional
information, see “Key Battery Low” (P. 2-34).

Since the Intelligent Key is capable of re-
ceiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and per-
sonal computer, the battery life may be-
come shorter.

For additional information, see “NISSAN In-
telligent Key® battery replacement” (P. 8-19).

Pay special attention that the vehicle bat-
tery is not completely discharged.

As many as four Intelligent Keys can be reg-
istered and used with one vehicle. For infor-
mation about the purchase and use of ad-
ditional Intelligent Keys, it is recommended
that you visit a NISSAN certified LEAF dealer.

OPERATING RANGE

The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range from the request
switch

When the Intelligent Key battery is dis-
charged or strong radio waves are present
near the operating location, the Intelligent
Key system’s operating range becomes
narrower, and the Intelligent Key may not
function properly.

The operating range is within 31.5 in (80 cm)
from each request switch

LVP0004X

Pre-driving checks and adjustments

3-7

If the Intelligent Key is too close to the door
glass or handle or rear bumper, the request
switches may not function.

When the Intelligent Key is within the oper-
ating range, it is possible for anyone, even
someone who does not carry the Intelli-
gent Key, to push the request switch to
lock/unlock the doors including the rear
hatch.

DOOR LOCKS/UNLOCKS
PRECAUTION

• Do not push the door handle request

switch with the Intelligent Key held in your
hand as illustrated. The close distance to
the door handle will cause the Intelligent
Key system to have difficulty recognizing
that the Intelligent Key is outside the
vehicle.

• After locking with the door handle request

switch, verify the doors are securely locked
by testing them.

• To prevent the Intelligent Key from being

left inside the vehicle, make sure you carry
the Intelligent Key with you and then lock
the doors.

• Do not pull the door handle before push-

ing the door handle request switch. The
door will be unlocked but will not open.
Release the door handle once and pull it
again to open the door.

LPD2687

3-8

Pre-driving checks and adjustments

NISSAN INTELLIGENT KEY®
OPERATION

You can lock or unlock the doors without
taking the Intelligent Key out of your pocket
or bag.

When you carry the Intelligent Key with you,
you can lock or unlock all doors by pushing
the door handle request switch within the
range of operation.

Locking doors

1. Place the power switch in the OFF posi-

tion and make sure you carry the Intelli-
gent Key with you.

2. Close all doors.

3. Push any door handle request switch

or rear hatch request switch

while

carrying the Intelligent Key with you.

4. All doors will lock.

5. The hazard indicator lights may flash

twice and the outside chime may sound
twice.

NOTE:
• Request switches for all doors and

hatch can be deactivated when the Ext.
Door Switch feature is switched to OFF
using the “Settings” menu on the ve-
hicle information display. For additional
information, see “Settings” (P. 2-27).

• Doors do not lock by pushing the door

handle request switch while the driv-
er’s door is open. However, the driver’s
door locks with the mechanical key
even if any door is open.

LPD2688

LPD2690

LPD3151

Pre-driving checks and adjustments

3-9

• Doors do not lock with the door handle

request switch with the Intelligent Key
inside the vehicle and a beep sounds to
warn you. However, when an Intelligent
Key is inside the vehicle, doors can be
locked with another Intelligent Key.

WARNING

After locking the doors using the re-
quest switch, make sure that the doors
have been securely locked by operat-
ing the door handles. Failure to follow
these instructions may result in inad-
vertently unlocking the door, which
may decrease the safety and security
of your vehicle.

CAUTION

•

When locking the doors using the re-
quest switch, make sure to have the
Intelligent Key in your possession
before operating the request switch.

•

The request switch is operational only
when the Intelligent Key has been de-
tected by the Intelligent Key system.

Lockout protection

To prevent the Intelligent Key from being
accidentally locked in the vehicle, lockout
protection is equipped with the Intelligent
Key system.

When the driver’s side door is open, the
doors are locked, then the Intelligent Key
is left inside the vehicle and the door is
closed, all doors will unlock automatically.

NOTE:

The doors may not lock when the Intelli-
gent Key is in the same hand that is op-
erating the request switch to lock the
door. Put the Intelligent Key in a purse,
pocket or your other hand.

CAUTION

The lockout protection may not func-
tion under the following conditions:

•

When the Intelligent Key is placed on
top of the instrument panel.

•

When the Intelligent Key is placed
inside the glove box or a storage bin.

•

When the Intelligent Key is placed
inside the door pockets.

•

When the Intelligent Key is placed
inside or near metallic materials.

Unlocking doors

1. Carry the Intelligent Key.

2. Push the door handle request switch

or the rear hatch request switch

once. The hazard indicator lights may
flash once and the outside chime may
sound once.

3. Push the door handle request switch

or the rear hatch request switch

again within 1 minute to unlock all doors.
The hazard indicator lights flash once
and the outside chime sounds once.

LPD2690

3-10

Pre-driving checks and adjustments

All doors will be locked automatically un-
less one of the following operations is per-
formed within one minute after pushing
the request switch:
• Opening any door.
• Pushing the power switch.

NOTE:

The Selective Unlock feature can be
changed using the “Settings” menu on the
vehicle information display. For additional
information, see “Settings” (P. 2-27).

Using the interior lights

The interior lights illuminate for a period of
time when a door is unlocked and the
room light switch is in the DOOR position.

The lights can be turned off without waiting
by performing one of the following opera-
tions:
• Placing the power switch in the ON posi-

tion.

• Locking the doors with the Intelligent Key.
• Switching the room light switch to the

“OFF” position.

For additional information, see “Interior lights”
(P. 2-70).

Opening rear hatch

1. Carry the Intelligent Key.

2. Push the rear hatch opener switch

3. The rear hatch will unlock and open.

LPD3151

LPD3152

Pre-driving checks and adjustments

3-11

HOW TO USE THE REMOTE
KEYLESS ENTRY FUNCTION

The remote keyless entry function can
operate all door locks using the remote
keyless function of the Intelligent Key. The
remote keyless function can operate at
a distance of 33 ft (10 m) away from the
vehicle. The operating distance depends
upon the conditions around the vehicle.

The remote keyless entry function will not
function under the following conditions:
• When the Intelligent Key is not within the

operational range.

• When the doors or the hatch are open or

not closed securely.

• When the Intelligent Key battery is dis-

charged.

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the electric medical equipment manu-
facturer for the possible influences
before use.

•

The Intelligent Key transmits radio
waves when the buttons are pressed.
The FAA advises that the radio waves
may affect aircraft navigation and
communications systems. Do not op-
erate the Intelligent Key while on an
airplane. Make sure the buttons are
not operated unintentionally when
the unit is stored during a flight.

CAUTION

•

Do not allow the Intelligent Key, which
contains electrical components, to
come into contact with water or salt
water. This could affect the system
function.

•

Do not drop the Intelligent Key.

•

Do not strike the Intelligent Key sharply
against another object.

•

Do not change or modify the Intelli-
gent Key.

•

Wetting may damage the Intelligent
Key. If the Intelligent Key gets wet, im-
mediately wipe until it is completely
dry.

•

Do not place the Intelligent Key for an
extended period in an area where
temperatures exceed 140°F (60°C).

•

Do not attach the Intelligent Key with
a key holder that contains a magnet.

•

Do not place the Intelligent Key near
equipment that produces a magnetic
field, such as a TV, audio equipment,
personal computers or cellular phone.

•

When locking the doors using the In-
telligent Key, be sure not to leave the
key in the vehicle.

LPD3111

(lock) button

(unlock) button

(charge port lid) button

(panic) button

3-12

Pre-driving checks and adjustments

Locking doors

1. Place the power switch in the LOCK

position.

2. Close all doors.

3. Press the

button on the Intelligent

Key.

4. The hazard indicator lights flash twice

and the horn beeps once.

5. All doors and the rear hatch will be locked.

WARNING

After locking the doors using the Intel-
ligent Key, be sure that the doors have
been securely locked by operating the
door handles. Failure to follow these in-
structions may result in inadvertently
unlocking the doors, which may de-
crease the safety and security of your
vehicle.

Unlocking doors

1. Press the

button on the Intelligent

Key to unlock the driver’s door.

2. The hazard indicator lights flash once.

3. Press the

button again within 1 min-

ute to unlock all doors and rear hatch.

All doors and rear hatch will be locked
automatically unless one of the following
operations is performed within 1 minute
after pressing the

button:

• Opening any doors or rear hatch.
• Pushing the power switch.

Using the interior lights

The interior lights illuminate for a period of
time when a door is unlocked and the
room light switch is in the DOOR position.

The lights can be turned off without waiting
by performing one of the following opera-
tions:
• Placing the power switch in the ON

position.

• Locking the doors with the Intelligent Key.
• Switching the room light switch to the

“OFF” position.

For additional information, see “Interior
lights” (P. 2-70).

Opening charge port lid

The charge port lid may be opened by
pressing and holding the

button.

For additional information, see "Opening
charge port lid" (P. 3-20).

Using the panic alarm

If you are near your vehicle and feel threat-
ened, you may activate the panic alarm
to call attention by pressing and holding
the

button on the Intelligent Key for

longer than 1 second.

The panic alarm and headlights will stay on
for a period of time.

The panic alarm stops when:
• It has run for a period of time.
• Any button is pressed on the Intelligent

Key. (Note: The

button must be

pushed for more than 1 second.)

Pre-driving checks and adjustments

3-13

Setting hazard indicator and horn
mode

This vehicle is set in hazard indicator and
horn mode when you first receive the vehicle.

In hazard indicator and horn mode, when
the

button is pressed, the hazard indi-

cator flashes twice and the horn chirps
once. When the

button is pressed, the

hazard indicator flashes once.

If horns are not necessary, the system can
be switched to the hazard indicator mode.

In hazard indicator mode, when the
button is pressed, the hazard indicator
flashes twice. When the

button is

pressed, neither the hazard indicator nor
the horn operates.

Hazard indicator and horn mode

Operation

DOOR LOCK

DOOR UNLOCK

Pushing door handle request switch or rear hatch request switch

HAZARD -

twice

OUTSIDE CHIME -

twice

HAZARD -

once

OUTSIDE CHIME -

once

Pressing

button

HAZARD -

twice

HORN -

once

HAZARD -

once

HORN - none

Hazard indicator mode

Operation

DOOR LOCK

DOOR UNLOCK

Pushing door handle request switch or rear hatch request switch

HAZARD -

twice

OUTSIDE CHIME - none

HAZARD - none
OUTSIDE CHIME - none

Pressing

button

HAZARD -

twice

HORN - none

HAZARD - none
HORN - none

3-14

Pre-driving checks and adjustments

Switching procedure:

To switch the hazard indicator and horn
(chime) operation, press the

and

buttons on the Intelligent Key simultane-
ously for more than two seconds.
• When the hazard indicator mode is set,

the hazard indicator flashes three times.

• When the hazard indicator and horn

mode is set, the hazard indicator flashes
once and the horn chirps once.

12-VOLT BATTERY SAVER SYSTEM

When all the following conditions are met
for a period of time, the battery saver sys-
tem will cut off the power supply to prevent
12-volt battery discharge.
• The power switch is in the ACC or ON

position,

• All doors are closed, and
• The vehicle is in the P (Park) position.

WARNING SIGNALS

To help prevent the vehicle from moving
unexpectedly by erroneous operation of
the Intelligent Key or to help prevent the
vehicle from being stolen, a chime or
buzzer sounds from inside and outside the
vehicle and a warning is displayed in the
instrument panel.

When a chime or beep sounds or a warning
is displayed, be sure to check the vehicle
and the Intelligent Key.

For additional information, see “Trouble-
shooting guide” (P. 3-16) and “Vehicle infor-
mation display warnings and indicator”
(P. 2-34 ).

NOS1695

Pre-driving checks and adjustments

3-15

TROUBLESHOOTING GUIDE

Verify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent Key is in range or inside the vehicle, the
vehicle system may respond differently than expected.

Symptom

Possible cause

Action to take

When opening the driver’s door
to get out of the vehicle

The inside warning chime sounds
continuously.

The power switch is pushed to the OFF
position while the driver's door is open.

Close the driver's door.

The power switch is in the ACC posi-
tion.

Push the power switch to the OFF posi-
tion then close the driver's door.

When closing the door after
getting out of the vehicle

The No Key Detected warning appears on
the display, the outside chime sounds
three times and the inside warning chime
sounds for a few seconds.

The power switch is in the ACC or ON
position.

Push the power switch to the OFF posi-
tion.

The Rear Door Alert warning message
appears on the display, the horn sounds
three times twice, or a Check Rear Seat for
All Articles warning appears on the display.

The Rear Door Alert is activated.

Check the back seat for all articles, press
the OK button to clear the Rear Door Alert
warning message.

The outside chime sounds continuously.

The power switch is in the ACC or OFF
position, the electric shift control sys-
tem has malfunctioned and the ve-
hicle cannot be placed in the P (Park)
position when the parking brake is not
applied.

Make sure the parking brake is applied.

When closing the door with the
inside lock knob turned to
LOCK

The outside chime sounds for a few
seconds and all the doors unlock.

The Intelligent Key is inside the vehicle
or cargo area.

Carry the Intelligent Key with you.

3-16

Pre-driving checks and adjustments

Symptom

Possible cause

Action to take

When pushing the request
switch or the

button on

the Intelligent Key to lock the
door

The outside chime sounds for a few
seconds.

The Intelligent Key is inside the vehicle
or a cargo area.

Carry the Intelligent Key with you.

When pushing the power
switch in the READY to drive
position

The EV system operation for discharged
Intelligent Key system indicator appears on
the display.

The Intelligent Key battery charge is
low.

For additional information, see “NISSAN
Intelligent Key® battery discharge” (P. 8-19).

The No Key Detected warning appears on
the display and the inside warning chime
sounds for a few seconds.

The Intelligent Key is not in the vehicle.

Carry the Intelligent Key with you.

When pushing the power
switch

The Key System Error indicator appears on
the display.

It warns of a malfunction with the
Intelligent Key system.

It is recommended that you visit a NISSAN
certified LEAF dealer.

Pre-driving checks and adjustments

3-17

Nissan Leaf (2024 year). Manual in english - page 8