Nissan Frontier (2024 year). Manual in english

WARNING

•

Never put metallic materials be-
tween the wireless charger and a
smartphone.

•

Those who use a pacemaker or other
medical equipment should contact
the electric medical equipment manu-
facturer for the possible influences
before use.

•

Never put cloth over the smartphone
during charging process.

•

Never charge a smartphone when it
is wet.

•

Never put metallic materials or small
goods such as a cigarette lighter, In-
telligent Key or memory drive.

CAUTION

•

Do not put an RFID/NFC/credit card
between the wireless charger and a
smartphone. This could cause data
corruption in the card.

•

Do not use the wireless charger with
dust accumulated or dirt on the pad.

•

Do not hit the surface of the wireless
charger.

•

Do not spill liquid (water, drinks, etc.)
on the charging pad.

•

Do not use grease, oil or alcohol for
cleaning charging pad.

WIRELESS CHARGER INDICATOR

The indicator ( 1 ) will illuminate in orange
when the charging process is started.

When the charging has completed, the in-
dicator illuminates in green.

If a malfunction occurs or the charging
process has stopped, the indicator will
blink in orange for 8 seconds then turn off.

WIRELESS CHARGER OPERATION

To use the wireless charger, it is necessary
to seat the smartphone well within the
charging pad. To maximize charging per-
formance, ensure the smartphone is fully
seated on the center of the charging pad
over the "Qi" logo

. Because the location

of the power receiver may vary depending
on the smartphone, you will need to try and
find the area that suits your smartphone.

Because some smartphone cases or ac-
cessories may adversely affect charging,
remove them before wireless charging.
Turn off the vibration function of the smart-
phone before wireless charging.

NOTE:

•

Only a Qi compatible smartphone can
be used.

•

The smartphone may be warmed dur-
ing charging process and the charging
may stop by the protection function
of the wireless charger. This is not a
malfunction. If this occurs, restart
charging after the smartphone has
cooled down. The indicator will blink in
orange then turn off.

•

The wireless charging process may be
stopped by the status of the smart-
phone (battery temperature, etc.).

•

If a radio noise interference occurs dur-
ing charging process, put the smart-
phone onto the center (“Qi” logo) posi-
tion of the wireless charger.

•

The wireless charging process will stop
during process of searching the Intelli-
gent Key.

•

The wireless charging process will not
be started when a USB (Universal Serial
Bus) cable is connected to the smart-
phone. The indicator may illuminate in
orange or blink if the smartphone is
put on the wireless charger with a USB
cable connected. However, charging is
not performed.

Instruments and controls

2-59

•

Depending on the type of the smart-
phone, the indicator may remain illu-
minated in orange even when the
charging process has been completed.

This device complies with part 15 of the
FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.
RF Radiation Exposure Statement: This
equipment complies with FCC RF Radia-
tion exposure limits set forth for an un-
controlled environment.
This device and its antenna must not be
co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and
operated with a minimum distance of
15cm between the radiator and your
body.

ISED Compliance Statement
This device complies with RSS-Gen of IC
Rules
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Changes or modifications made to this
device, not expressly approved by LG
Vehicle Components Company, will void
the user’s authority to operate the
equipment.
ISED RF Radiation Exposure Statement:
This equipment complies with ISED RF
Radiation exposure limits set forth for an
uncontrolled environment. This device
and its antenna must not be co-located
or operating in conjunction with any
other antenna or transmitter. This equip-
ment should be installed to operate with
a minimum distance of 15 cm between
the radiator and the end-user’s body and
arms.

The Rear Door Alert system functions un-
der certain conditions to indicate there
may be an object or passenger in the rear
seat(s). Check the seat(s) before exiting the
vehicle.

The Rear Door Alert system is initially dis-
abled. The driver can enable the system
using the vehicle information display. For
additional information, see “Vehicle infor-
mation display warnings and indicators”
(P. 2-31).

When the system is enabled:
• The system is activated when a rear door

is opened and closed within 10 minutes of
the vehicle being driven. When the driver’
door is closed and the system is acti-
vated, a visual message appears in the
vehicle information display. For additional
information, see “Rear Door Alert is acti-
vated” (P. 2-32).

• If a rear door is opened and closed but

the vehicle is not driven within approxi-
mately 10 minutes, the system will not be
activated. A rear door must be opened
and closed and the car driven within 10
minutes for the system to activate.

REAR DOOR ALERT

2-60

Instruments and controls

When the Rear Door Alert system is acti-
vated and a driver exits the vehicle after
arriving at a destination:
• When the driver puts the vehicle in the P

(Park) position, a message appears in the
vehicle information display for a driver
to “Dismiss Message” or “Disable Alert” if
desired.

• With the system enabled, when the driver

exits the vehicle, an audible alert (horn
sound) will occur unless a rear door is
opened and closed within a short time to
deactivate the alert.

• If the doors are locked before the alert is

deactivated by opening a rear door, the
horn will sound.

• If the audible horn alert occurs, a mes-

sage will also appear in the vehicle infor-
mation display that states, “Check Rear
Seat for All Articles”.

WARNING

• If the driver selects “Disable Alert”, no

audible alert will be provided regard-
less of rear door open/close status.

• There may be times when there is an

object or passenger in the rear seat(s)
but the audible alert does not sound.

For example, this may occur if rear
seat passengers enter or exit the ve-
hicle during a trip.

• The system does not directly detect

objects or passengers in the rear
seat(s). Instead, it can detect when a
rear door is opened and closed, indi-
cating that there may be something in
the rear seat(s).

NOTE:

There may be times when the horn
sounds but there are no objects or pas-
sengers in the rear seat(s).

For additional information, see “Rear Door
Alert is activated” (P. 2-32).

12V OUTLETS

The power outlets are for powering electrical
accessories such as cellular telephones.
The power outlet located on the instru-
ment panel is powered only when the igni-
tion switch is placed in the ACC or ON
position.

Open the cap to use a power outlet.

CAUTION

•

The outlet and plug may be hot dur-
ing or immediately after use.

LIC4831

Instrument panel

POWER OUTLETS

Instruments and controls

2-61

•

Only certain power outlets are de-
signed for use with a cigarette lighter
unit. Do not use any other power out-
let for an accessory lighter. It is rec-
ommended that you visit a NISSAN
dealer for additional information.

•

Do not use with accessories that ex-
ceed a 12 volt, 120W (10A) power draw.

•

Do not use double adapters or more
than one electrical accessory.

•

Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.

•

Avoid using power outlets when the
air conditioner, headlights, or rear
window defroster (if so equipped) is
on.

•

Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned OFF.

•

Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.

•

When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.

120V OUTLETS (if so equipped)

LIC0617

In truck box (if so equipped)

LIC4837

Center console (if so equipped)

2-62

Instruments and controls

120V OUTLET

Switch Reset

What is plugged in

Shifter In Park

Shifter Out of Park

Shifter Back In Park

Shifter In Park

Shifter Out of Park

Indicator

Inverter

Status

Indicator

Inverter

Status

Indicator

Inverter

Status

Indicator

Inverter

Status

Indicator

Inverter

Status

No Device but

Switch On

150W and 400W

150W

150W and 400W

150W

Device<150W

150W and 400W

150W

150W and 400W

150W

150W<Device<400W

150W and 400W

OFF

150W and 400W

OFF**

Device>400W

OFF

OFF**

** OFF means the inverter system cannot be reset until a device is within the specification range of operation. If the device is greater than specified, the inverter
will shut OFF. The operating voltage is between 11.5v and 15v. If the vehicle is not idling, the battery voltage will drop which will cause the inverter to shut down
when below 11.5v. When the vehicle is in the (P) Park position, it will work at 400W. If the vehicle is in any other shifter position, it will turn off.

Do not use the outlet located in the truck
box with accessories that exceed 120 volt.
Do not use double adapters or more than
one electrical accessory.

CAUTION

•

Operation of the 120 volt system with
the ignition in the ON position and
the engine not running (idle) will
drain the battery charge. This could
lead to a dead battery or no start
condition.

•

The outlet and plug may be hot dur-
ing or immediately after use.

•

Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.

•

Do not use double adaptors or more
than one electrical accessory.

•

Avoid using power outlets when the
air conditioner, headlights or rear
window defroster is on.

•

Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned OFF.

•

Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.

•

When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.

Instruments and controls

2-63

SEATBACK POCKET

A seatback pocket is located on the back of
the passenger’s seat. The pocket may be
used to store maps.

WARNING

To ensure proper operation of the driv-
er’s and/or front passenger’s NISSAN
Advanced Air Bag System, please ob-
serve the following items:

•

Do not allow a passenger in the rear
seat to push or pull on the seatback
pocket or head restraint/headrest.

•

Do not place heavy loads heavier than
9.1 lbs. (4 kg) on the seatback, head
restraint/headrest or in the seatback
pocket.

UNDER-SEAT STORAGE BINS (if so
equipped)

LIC1328

LIC4496

Rear row under-seat storage bin

(King Cab® model)

2-66

Instruments and controls

WARNING

•

Properly secure all cargo with ropes
or straps to help prevent it from
sliding or shifting. In a sudden stop or
collision,

unsecured

cargo

could

cause personal injury.

•

The cargo restrained in the under-
seat storage bins must not exceed
the weight limits listed below or the
bins may not stay secured. In a sud-
den stop or collision, the unsecured
bins could cause personal injury.
King Cab® model: 16 lbs. (7.25 kg)
Crew Cab model

Driver’s side: 16 lbs. (7.25 kg)
Passenger’s side: 25 lbs. (11.33 kg)

•

If the under-seat storage bins are re-
moved for any reason, they should be
securely stored to prevent them from
causing injury to passengers or dam-
age to the vehicle in case of sudden
braking or an accident.

•

Do not place sharp objects in the
under-seat storage bins. Such ob-
jects may become dangerous projec-
tiles and cause injury when the
vehicle is moving or if the vehicle is
involved in a collision.

To access the under-seat storage bins:

For King Cab® models, lift up the jump seat.
For additional information, see “Jump seat”
(P. 1-6).

For Crew Cab models, lift up the rear bench
seat. For additional information, see “Fold-
ing the rear bench seat down” (P. 1-7).

LIC4497

Rear row under-seat storage bin

(Crew Cab model)

Instruments and controls

2-67

To remove the under-seat storage bins:

1. Turn the knobs to the UNLOCK position

2. Remove the tray (if so equipped) by lift-

ing it out of the storage bin (King Cab®
model).

To install the under-seat storage bins:

1. Position the under-seat storage bin so

the holes line up with the holes in the
floorboard.

2. Insert the knobs and turn them to the

LOCK position

STORAGE TRAYS

WARNING

Do not place sharp objects in the trays
to help prevent injury in an accident or
sudden stop.

LIC0822

LIC4875

Top center tray (if so equipped)

LIC4851

Center console (if so equipped)

2-68

Instruments and controls

GLOVE BOX

Open the glove box by pulling the handle.
Use the mechanical key (if so equipped)
when locking or unlocking the glove box.

WARNING

Keep the glove box lid closed while
driving to help prevent injury in an ac-
cident or a sudden stop.

CONSOLE BOX

Pull up on the lever

to open the console

box lid

OVERHEAD SUNGLASSES
STORAGE (if so equipped)

To open the sunglasses holder, push and
release.

Only store one pair of sunglasses in the
holder.

WARNING

Keep the sunglasses holder closed
while driving to avoid obstructing the
driver’s view and to help prevent an
accident.

LIC4843

LIC4874

LIC3387

Instruments and controls

2-69

CAUTION

•

Do not use for anything other than
sunglasses.

•

Do not leave sunglasses in the sun-
glasses holder while parking in direct
sunlight. The heat may damage the
sunglasses.

CUP HOLDERS

CAUTION

•

Avoid abrupt starting and braking
when the cup holder is being used
to prevent spilling the drink. If the
liquid is hot, it can scald you or your
passenger.

•

Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.

LIC4826

Front

LIC5497

Rear seat (if so equipped)

2-70

Instruments and controls

CAUTION

•

Do not use the bottle holder for any
other objects that could be thrown
about in the vehicle and possibly in-
jure people during sudden braking or
an accident.

•

Do not use the bottle holder for open
liquid containers.

COAT HOOKS (if so equipped)

The coat hooks, located on the rear assist
grips, may be used to store coats and other
articles of clothing.

CAUTION

Do not apply more than 33 lbs. (15 kg) to
the rear assist grip coat hook.

LIC4828

Front row bottle holders

LIC4833

Rear bottle holders

LIC4173

Instruments and controls

2-71

POWER WINDOWS

WARNING

•

Make sure that all passengers have
their hands, etc., inside the vehicle
while it is in motion and before clos-
ing the windows. Use the window
lock switch to prevent unexpected
use of the power windows.

•

To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not
leave children, people who require
the assistance of others or pets unat-
tended in your vehicle. Additionally,
the temperature inside a closed ve-
hicle on a warm day can quickly be-
come high enough to cause a signifi-
cant risk of injury or death to people
and pets.

The power windows operate when the ig-
nition switch is placed in the ON position or
for a period of time after the ignition switch
is placed in the ACC or OFF position. If the
driver's or passenger's door is opened dur-
ing this period of time, the power to the
windows is canceled.

Driver's side power window switch

The driver's side control panel is equipped
with switches to open or close the front
and rear passenger windows.

To open a window, push the switch and
hold it down. To close a window, pull the
switch and hold it up. To stop the opening
or closing function at any time, simply re-
lease the switch.

LIC1329

1. Window lock button

2. Power door lock switch

3. Front passenger side window switch

4. Right rear passenger window switch

(Crew Cab models only)

5. Left rear passenger window switch

(Crew Cab models only)

6. Driver's side automatic switch

WINDOWS

2-72

Instruments and controls

Front passenger's power window
switch

The passenger's window switch operates
only the corresponding passenger's win-
dow. To open the window, push the switch
and hold it down

. To close the window,

pull the switch up

Rear power window switch
(Crew Cab models only)

The rear power window switches open or
close only the corresponding passenger
window. To open the window, push the
switch and hold it down

. To close the

window, push the switch up

Locking passengers' windows

When the window lock switch is depressed,
only the driver's side window can be
opened or closed. Push it again to cancel
the window lock function.

Automatic operation

To fully open a window equipped with au-
tomatic

operation,

push

the

window

switch down to the second detent and re-
lease it; it need not be held. The window
automatically opens all the way. To stop
the window, lift the switch up while the win-
dow is opening.

WIC0260

LIC2663

LIC0410

Instruments and controls

2-73

REAR SLIDING WINDOW (if so
equipped)

WARNING

•

You must ensure all occupants and
objects are free of the rear window
area prior to and during operation.
Failure to do so may result in injury
and/or damage to the rear window
system.

•

The rear window is not designed to
carry long items through it.

•

Do not place objects through the
opened rear window. Do not use the
rear window as a cargo area pass-
through. This may result in damage
to the rear window system or per-
sonal injury.

Squeeze the handles of the lever

, then

slide the window open

POWER MOONROOF

The moonroof will only operate when the
ignition switch is in the ON position. The
power moonroof is operational for about
45 seconds, even if the ignition switch is
placed in the ACC or OFF position. If the
driver's door or the front passenger's door is
opened during this period of about 45 sec-
onds, power to the moonroof is canceled.

LIC3488

LIC4830

MOONROOF (if so equipped)

2-74

Instruments and controls

Sliding the moonroof

To open the moonroof, push the switch
toward DOWN/OPEN

and release it.

Push the switch again to fully open the
moonroof.

To fully close the moonroof, push the
switch toward UP/CLOSE

and release it.

To open or close the moonroof part way,
push the switch in any direction while the
moonroof is sliding to stop it in the desired
position.

Tilting the moonroof

Close the moonroof by pushing the switch
toward UP/CLOSE

. Release the switch,

then push the UP/CLOSE switch again to
tilt the moonroof up.

To tilt the moonroof down, push the switch
toward DOWN/OPEN

Auto-reverse function (when
closing or tilting down the
moonroof)

The auto-reverse function can be acti-
vated when the moonroof is closed or
tilted down by automatic operation when

the ignition switch is placed in the ON po-
sition or for a period of time after the igni-
tion switch is placed in the OFF position.

Depending on the environment or driv-
ing conditions, the auto-reverse func-
tion may be activated if an impact or
load similar to something being caught
in the moonroof occurs.

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the moonroof.

When closing

If the control unit detects something
caught in the moonroof as it moves to the
front, the moonroof will immediately open
backward.

When tilting down

If the control unit detects something
caught in the moonroof as it tilts down, the
moonroof will immediately tilt up.

If the auto-reverse function malfunctions
and repeats opening or tilting up the moon-
roof, keep pushing the tilt down switch within
5 seconds after it happens; the moonroof
will fully close gradually. Make sure nothing is
caught in the moonroof.

WARNING

•

In an accident you could be thrown
from the vehicle through an open
moonroof. Always use seat belts and
child restraints.

•

Do not allow anyone to stand up or
extend any portion of their body out
of the moonroof opening while the
vehicle is in motion or while the
moonroof is closing.

CAUTION

•

Remove water drops, snow, ice or sand
from the moonroof before opening.

•

Do not place heavy objects on the
moonroof or surrounding area.

Instruments and controls

2-75

Sunshade

Open and close the sunshade by sliding it
forward or backward.

If the moonroof does not close

Have your moonroof checked and re-
paired. It is recommended that you visit a
NISSAN dealer for this service.

The interior light has a three-position
switch and operates regardless of ignition
switch position.

When the switch is in the ON position

the interior lights illuminate, regardless of
door position. The lights will go off after a
period of time unless the ignition switch is
placed in the ON position.

When the switch is in the DOOR or normal
operation position

, the interior lights will

stay on for a period of time and the cargo
light may illuminate when:

• The doors are unlocked by the key fob,

a key or the power door lock switch while
all doors are closed and the ignition
switch is in the OFF position.

• The driver’s door is opened and then

closed while the ignition switch is placed
in the OFF position.

• The ignition switch is placed in the OFF

position while all doors are closed.

The lights will turn off while the timer is
activated when:
• The driver’s door is locked by the key fob,

a key, or the power door lock switch.

• The ignition switch is placed in the ON

position.

When the switch is in the OFF position

the interior lights do not illuminate, regard-
less of door position. The cargo light may
illuminate when any front or rear passen-
ger door is opened.
The lights will turn off automatically after a
period of time while doors are open to pre-
vent the battery from becoming discharged.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could
result in a discharged battery.

LIC0792

INTERIOR LIGHTS

2-76

Instruments and controls

MAP LIGHTS

To turn the map lights on, press the lenses.
To turn them off, press the lenses of the
map lights again.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

CARGO LIGHT

The cargo light on the overhead trim has a
three-position switch. To operate, push the
switch to the desired position.

ON: The light is illuminated.

DOOR: The light illuminates when the rear
doors are opened. The light turns off when
the rear doors are closed.

OFF: The light does not illuminate regard-
less of door position or lock status.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could
result in a discharged battery.

LIC0790

LIC0590

Instruments and controls

2-77

The HomeLink® Universal Transceiver pro-
vides a convenient way to consolidate the
functions of up to three individual hand-
held transmitters into one built-in device.

HomeLink® Universal Transceiver:
• Will operate most Radio Frequency (RF)

devices such as garage doors, gates,
home and office lighting, entry door locks
and security systems.

• Is powered by your vehicle's battery. No

separate batteries are required. If the
vehicle's battery is discharged or is dis-
connected, HomeLink® will retain all pro-
gramming.

When the HomeLink® Universal Trans-
ceiver is programmed, retain the original
transmitter for future programming pro-
cedures (Example: new vehicle purchases).
Upon sale of the vehicle, the programmed
HomeLink® Universal Transceiver buttons
should be erased for security purposes.
For additional information, see “Program-
ming HomeLink®” (P. 2-78).

WARNING

•

Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards
became effective for opener models
manufactured after April 1, 1982.) A
garage door opener which cannot
detect an object in the path of a clos-
ing garage door and then automati-
cally stop and reverse does not meet
current federal safety standards.
Using a garage door opener without
these features increases the risk of
serious injury or death.

•

During the programming procedure
your garage door or security gate will
open and close (if the transmitter is
within range). Make sure that people
or objects are clear of the garage door,
gate, etc., that you are programming.

•

Your vehicle's engine should be
turned off while programming the
HomeLink® Universal Transceiver. Do
not breathe exhaust gases; they con-
tain colorless and odorless carbon
monoxide. Carbon monoxide is dan-
gerous. It can cause unconscious-
ness or death.

PROGRAMMING HOMELINK®

The following steps show generic instruc-
tions on how to program a HomeLink® but-
ton. If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com/nissan or call 1-800-
355-3515.

NOTE:

It is also recommended that a new bat-
tery be placed in the hand-held trans-
mitter of the device being programmed
to HomeLink® for quicker programming
and accurate transmission of the radio-
frequency.

HOMELINK® UNIVERSAL
TRANSCEIVER (if so equipped)

2-78

Instruments and controls

䊊

HomeLink® buttons (1–3)

䊊

Indicator light (appears above each
HomeLink® button)

1. Position the end of your hand-held

transmitter 1-3 inches (2-8 cm) away
from the HomeLink® button that you
would wish to program while keeping
the indicator light in view.

2. Simultaneously press and hold both the

chosen HomeLink® and hand-held trans-
mitter buttons until the HomeLink® in-
dicator light changes from a slow to a
rapidly blinking light. Now you may re-
lease both the HomeLink® and hand-held
transmitter buttons.

NOTE:

Some hand-held transmitters (garage
door opener remote) may actually train
better at a distance of 6–12 inches (15–
20 cm). Keep this in mind if you have
difficulty with the programming process.

3. Firmly

press, hold for five seconds and

release

the programmed HomeLink®

button up to two separate times to ac-
tivate the door. If the door does not acti-
vate, press and hold the just trained
HomeLink® button and observe the indi-
cator light.

• If the indicator light

stays on con-

stantly, programming is complete

and your device should activate when
the Homelink® button is pressed and
released.

• If the indicator light blinks

rapidly for

two seconds and then turns to a
constant light, continue with “Pro-
gramming” steps 4–6

to complete

the programming of a rolling code
equipped device (most commonly a
garage door opener).

LIC5068

LIC5069

Instruments and controls

2-79

NOTE:

Some devices may require you to replace
this Programming Step 2 with procedures
noted in the “Programming HomeLink®
for Canadian customers and gate openers”
(P. 2-80) section. If the HomeLink® indicator
light does not change to a rapidly blinking
light after performing these steps, contact
HomeLink® at www.homelink.com.

4. At the garage door opener motor (secu-

rity gate motor, etc.), locate the “Learn” or
“Set” button. This can usually be found
where the hanging antenna wire is at-
tached to the motor-head unit (see the
device’s manual to identify this button.).
The name and color of the button may
vary by manufacturer.

NOTE:

A ladder and/or second person may sim-
plify the following steps. Do not stand on
your vehicle to perform the next steps.

5. Firmly press and release the “Learn” or

“Set” button until the indicator illumi-
nates. Once the button is pressed, you
have approximately 30 seconds to initi-
ate the next step.

6. Return to the vehicle and firmly press,

hold for two seconds and release the
HomeLink® button up to three times.

Do not press the HomeLink® button
rapidly.

At this point programming is

complete and your device should oper-
ate when the HomeLink® button is
pressed and released.

7. If you have any questions or are having

difficulty programming your HomeLink®
buttons, refer to the HomeLink® web
site at: www.homelink.com/nissan or call
1-800-355-3515.

PROGRAMMING HOMELINK® FOR
CANADIAN CUSTOMERS AND GATE
OPENERS

Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission –
which may not be long enough for
HomeLink® to pick up the signal during
training. Similar to this Canadian law, some
U.S. gate operators are designed to “time-
out” in the same manner.

If you live in Canada or you are having diffi-
culties training a gate operator

garage

door opener by using the “Programming
HomeLink®” procedures,

replace

“Program-

ming HomeLink®”

step 2

with the following:

NOTE:

When programming a garage door opener,
etc., unplug the device during the “cycling”
process to prevent possible damage to the
device components.

LIC4798

Example

2-80

Instruments and controls

Step 2: Continue to press and hold the
HomeLink® button while you press and re-
lease – every two seconds (“cycle”) your
hand-held transmitter until the HomeLink®
indicator light changes from a slow to a
rapidly blinking light. Now you may release
both the Homelink® and hand-held trans-
mitter buttons.

Proceed with “Programming HomeLink®”
step 3 to complete.

Remember to plug the device back in when
programming is completed.

OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER

The HomeLink® Universal Transceiver, after
it is programmed, can be used to acti-
vate the programmed device. To operate,
firmly press the appropriate programmed
HomeLink® button. The indicator light will
illuminate in green with three parenthesis

on the mirror while the signal is being

transmitted.

PROGRAMMING TROUBLE-
SHOOTING

If the HomeLink® does not quickly learn the
hand-held transmitter information:
• Replace the hand-held transmitter bat-

teries with new batteries.

• Position the hand-held transmitter with

its battery area facing away from the
HomeLink® button.

• Press and hold both the HomeLink® but-

ton and hand-held transmitter button in
each step without interruption.

• Position the hand-held transmitter 1 to

3 in (2 to 8 cm) away from the HomeLink®
button. Hold the transmitter in that posi-
tion for up to 15 seconds. If HomeLink® is
not programmed within that time, try
holding the transmitter in another posi-
tion – for example, 6 to 12 in (15 to 20 cm)
away, keeping the HomeLink® button in
view at all times.

It is recommended not to place metal ob-
jects near the garage door opener an-
tenna for optimal functionality.

If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com/nissan or call 1-800-
355-3515.

CLEARING THE PROGRAMMED
INFORMATION

The following procedure clears the pro-
grammed information from three buttons.
Individual buttons cannot be cleared. How-
ever, individual buttons can be repro-
grammed. For additional information, see
“Reprogramming a single HomeLink® but-
ton” (P. 2-82).

To clear all programming

1. Press and hold the two outer HomeLink®

buttons until the indicator light begins to
flash in green in approximately 10 seconds.
Do not hold for longer than 20 seconds.

2. Release both buttons.

HomeLink® is now in the programming
mode and can be programmed at any time
beginning with “Programming HomeLink®” -
Step 1.

Instruments and controls

2-81

REPROGRAMMING A SINGLE
HOMELINK® BUTTON

To reprogram a HomeLink® button, com-
plete the following:

1. Press and hold the desired HomeLink®

button.

DO NOT

release the button.

2. The indicator light will begin to flash

after 20 seconds. Without releasing the
HomeLink® button, proceed with “Pro-
gramming HomeLink®” — step 1.

For

questions

comments,

contact

HomeLink® at: www.homelink.com/nissan
or 1–800–355–3515.

The HomeLink® button has now been re-
programmed. The new device can be acti-
vated by pressing the HomeLink® button
that was just programmed. This procedure
will not affect any other programmed
HomeLink® buttons.

If a new device is not programmed to the
HomeLink® button, it will revert to the pre-
viously stored programming.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should change
the codes of any non-rolling code de-
vice that has been programmed into
HomeLink®. Consult the Owner's Manual
of each device or call the manufacturer
or dealer of those devices for additional
information.

When your vehicle is recovered, you will
need to reprogram the HomeLink® Uni-
versal Transceiver with your new trans-
mitter information.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any inter-
ference received, including interference
that may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

For Canada:

This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This
device must accept any interference,
including interference that may cause
undesired operation of the device.

2-82

Instruments and controls

NISSAN INTELLIGENT KEY®

Your vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key system com-
ponents and NISSAN Vehicle Immobilizer
System components.

Never leave these keys in the vehicle.

As many as four Intelligent Keys can be
registered and used with one vehicle. The
new keys must be registered by a NISSAN
dealer prior to use with the Intelligent Key
system and NISSAN Vehicle Immobilizer
System of your vehicle. Since the registra-
tion process requires erasing all memory in
the Intelligent Key components when reg-
istering new keys, be sure to take all Intelli-
gent Keys that you have to the NISSAN
dealer.

A key number plate is supplied with your
keys. Record the key number and keep it in
a safe place (such as your wallet), not in the
vehicle. If you lose your keys, it is recom-
mended that you visit a NISSAN dealer for
duplicates by using the key number.
NISSAN does not record key numbers so it
is very important to keep track of your key
number plate.

A key number is only necessary when you
have lost all keys and do not have one to
duplicate from. If you still have a key, it can
be duplicated without knowing the key
number.

CAUTION

Listed below are conditions or occur-
rences which will damage the Intelli-
gent Key:

•

Do not allow the Intelligent Key, which
contains electrical components, to
come into contact with water or salt
water. This could affect the system
function.

•

Do not drop the Intelligent Key.

•

Do not strike the Intelligent Key sharply
against another object.

LPD3106

Type A (if so equipped)

1. Two Intelligent Keys

2. Mechanical key

3. Master key

4. Key number plate

LPD3605

Type B (if so equipped)

KEYS

3-2

Pre-driving checks and adjustments

•

Do not change or modify the Intelli-
gent Key.

•

Wetting may damage the Intelligent
Key. If the Intelligent Key gets wet,
immediately wipe until it is com-
pletely dry.

•

Do not place the Intelligent Key for an
extended period in an area where
temperatures exceed 140°F (60°C).

•

Do not attach the Intelligent Key with
a key holder that contains a magnet.

•

Do not place the Intelligent Key near
equipment that produces a magnetic
field, such as a TV, audio equipment
and personal computers.

If an Intelligent Key is lost or stolen,
NISSAN recommends erasing the ID
code of that Intelligent Key from the
vehicle. This may prevent the unau-
thorized use of the Intelligent Key to
operate the vehicle. For information
regarding the erasing procedure, it is
recommended that you visit a NISSAN
dealer.

Mechanical key

The Intelligent Key contains the mechani-
cal key.

To remove the mechanical key, release the
lock knob on the back of the Intelligent Key.

To install the mechanical key, firmly insert it
into the Intelligent Key until the lock knob
returns to the lock position.

Use the mechanical key to lock or unlock
the driver's door, tailgate and glove box
(if so equipped).

CAUTION

Always carry the mechanical key in-
stalled in the Intelligent Key slot.

For additional information, see “Doors” (P. 3-4),
“Tailgate” (P. 3-27) or “Glove box” (P. 2-69).

Valet hand-off (if so equipped)

When you have to leave a key with a valet,
give them the Intelligent Key itself and keep
the mechanical key and the master key
with you to protect your belongings.

To prevent the glove box from being
opened during valet hand-off, follow the
procedure below.

1. Remove the mechanical key from the

Intelligent Key.

2. Lock the glove box (if so equipped) with

the mechanical key or master key.

3. Hand the Intelligent Key to the valet and

keep the mechanical key and the mas-
ter key with you.

For additional information, see “Glove box”
(P. 2-69).

SPA1951

Pre-driving checks and adjustments

3-3

NISSAN VEHICLE IMMOBILIZER
SYSTEM KEYS

Additional or replacement keys:

If you still have a key, the key number is not
necessary when you need extra NISSAN
Vehicle Immobilizer System keys. Your ex-
isting key can be duplicated without know-
ing the key number. As many as four
NISSAN Vehicle Immobilizer System keys
can be used with one vehicle. You should
bring all NISSAN Vehicle Immobilizer Sys-
tem keys that you have to the NISSAN
dealer for registration. This is because the
registration process will erase the memory
of all key codes previously registered into
the NISSAN Vehicle Immobilizer System. Af-
ter the registration process, these compo-
nents will only recognize keys coded into
the NISSAN Vehicle Immobilizer System
during registration. Any virtual key acces-
sories (if so equipped) will also have to be
reregistered. Any key that is not given to the
dealer at the time of registration will no
longer be able to start your vehicle.

CAUTION

Do not allow the immobilizer system
key, which contains an electrical tran-
sponder, to come into contact with wa-
ter or salt water. This could affect sys-
tem function.

When the doors are locked using one of the
following methods, the doors cannot be
opened using the inside or outside door
handles. The doors must be unlocked to
open the doors.

WARNING

•

Always have the doors locked while
driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping to
prevent persons from being thrown
from the vehicle. This also helps keep
children and others from uninten-
tionally opening the doors, and will
help keep out intruders.

•

Before opening any door, always look
for and avoid oncoming traffic.

•

DOORS

3-4

Pre-driving checks and adjustments

LOCKING WITH KEY

To lock the door using the mechanical key,
turn the key toward the rear of the vehicle

. This will only lock the door and will not

activate the security system. To arm the
security system, press the

button on

the Intelligent Key.
To unlock the door using the mechanical
key, turn the key toward the front of the
vehicle

. This will only unlock the corre-

sponding door and will not disarm the se-
curity system.
For additional information, see “Security
systems” (P. 2-37).

LOCKING WITH INSIDE LOCK KNOB

To lock the door without the key, move the
inside lock knob to the lock position

then close the door.
To unlock the door without the key, move
the inside lock knob to the unlock position

To unlock or open the front doors without
using the lock knob, pull once on the door
handle

to unlock it, and again to open it.

LOCKING WITH POWER DOOR
LOCK SWITCH

To lock all the doors without a key, push the
door lock switch (driver's or front passen-
ger's side) to the lock position

. When

locking the door this way, be certain not to
leave the key inside the vehicle.

To unlock all the doors without a key, push
the door lock switch (driver's or front pas-
senger's side) to the unlock position

LPD3246

Driver’s side

LPD3394

Inside lock

WPD0381

Pre-driving checks and adjustments

3-5

REAR DOORS (King Cab® models)

1. Open the driver's or passenger's door.

2. From the outside, pull the door handle

toward you.

3. Open the door to the desired position.

AUTOMATIC DOOR LOCKS

• All doors lock automatically when the

vehicle speed reaches 15 mph (24 km/h).

• All doors unlock automatically when the

transmission is placed in the P (Park) posi-
tion on automatic transmission equipped
vehicles, or when the ignition is placed in
the OFF position on manual transmission
equipped vehicles.

LPD0278

LPD3300

WPD0313

3-6

Pre-driving checks and adjustments

CHILD SAFETY REAR DOOR LOCK
(if so equipped)

Child safety locks help prevent the rear
doors from being opened accidentally, es-
pecially when small children are in the
vehicle.

The child safety lock levers are located on
the edge of the rear doors.

When the lever is in the LOCK position,
the door can be opened only from the
outside.

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the electric medical equipment manu-
facturer for the possible influences
before use.

•

The Intelligent Key transmits radio
waves when the buttons are pressed.
The FAA advises the radio waves may
affect aircraft navigation and com-
munication systems. Do not operate
the Intelligent Key while on an air-
plane. Make sure the buttons are not
operated unintentionally when the
unit is stored for a flight.

•

Make sure to engage the P (Park) po-
sition and apply the parking brake
when parking your vehicle, entering
or exiting the vehicle or loading lug-
gage. Failure to do so could cause the
vehicle to move or roll away unex-
pectedly and result in serious per-
sonal injury or property damage.

The Intelligent Key system can operate all
the door locks using the remote control
function or pushing the request switch (if

so equipped) on the vehicle without taking
the key out from a pocket or purse. The
operating environment and/or conditions
may affect the Intelligent Key system op-
eration.

Be sure to read the following before using
the Intelligent Key system.

CAUTION

•

Be sure to carry the Intelligent Key
with you when operating the vehicle.

•

Never leave the Intelligent Key in the
vehicle when you leave the vehicle.

The Intelligent Key is capable of receiving
and transmitting radio waves. The Intelli-
gent Key system transmits weak radio
waves from various distances. Environ-
mental conditions may interfere with the
operation of the Intelligent Key system un-
der the following operating conditions:
• When operating near a location where

strong radio waves are transmitted, such
as a TV tower, power station and broad-
casting station.

• When in possession of wireless equip-

ment, such as a cellular telephone, trans-
ceiver or a CB radio.

LPD3380

NISSAN INTELLIGENT KEY® SYSTEM

Pre-driving checks and adjustments

3-7

• When the Intelligent Key is in contact with

or covered by metallic materials.

• When any type of radio wave remote con-

trol is used nearby.

• When the Intelligent Key is placed near an

electric appliance such as a personal
computer.

• When the vehicle is parked near a parking

meter.

In such cases, correct the operating condi-
tions before using the Intelligent Key func-
tion or use the mechanical key.

Although the life of the battery varies de-
pending on the operating conditions, the
battery’s life is approximately two years.
If the battery is discharged, replace it with a
new one.

When the Intelligent Key battery is low, the
“Key Battery Low” indicator illuminates in
the vehicle information display. For addi-
tional information, see “Vehicle information
display” (P. 2-20).

Since the Intelligent Key is capable of re-
ceiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and per-
sonal computer, the battery life may be-
come shorter.

For additional information, see “Battery re-
placement” (P. 8-25).

Pay special attention that the vehicle bat-
tery is not completely discharged.

As many as four Intelligent Keys can be
registered and used with one vehicle. For
information about the purchase and use
of additional Intelligent Keys, it is recom-
mended that you visit a NISSAN dealer.

3-8

Pre-driving checks and adjustments

Nissan Frontier (2024 year). Manual in english - page 6