Nissan Armada (2019 year). Instruction

WARNING

. Your brake system may not be

working properly if the warning
light is on. Driving could be dan-
gerous. If you judge it to be safe,
drive carefully to the nearest
service station for repairs. Other-
wise, have your vehicle towed
because driving it could be dan-
gerous.

. Pressing the brake pedal with the

engine stopped and/or low brake
fluid level may increase your
stopping distance and braking
will require greater pedal effort
as well as pedal travel.

. If the brake fluid level is below the

minimum or MIN mark on the
brake fluid reservoir, do not drive
until the brake system has been
checked. It is recommended you
visit a NISSAN dealer for this
service.

Charge warning light

If the light comes on while the engine is
running, it may indicate the charging
system is not functioning properly. Turn
the engine off and check the alternator
belt. If the belt is loose, broken, missing or
if the light remains on, have your vehicle
serviced immediately. It is recommended
you visit a NISSAN dealer for this service.

CAUTION

Do not continue driving if the alter-
nator belt is loose, broken or miss-
ing.

Intelligent Distance Control (I-

DC) system warning light (orange; if
so equipped)

This light comes on if there is a malfunc-
tion in the Intelligent Distance Control (I-
DC) system.

If the warning light illuminates, park the
vehicle in a safe place. Turn the engine off,
restart the engine, resume driving and
turn on the I-DC system again.

If it is not possible to turn on the system
or the warning light stays on, it may

indicate that the system is malfunction-
ing. Although the vehicle is still drive-
able under normal conditions, have the
vehicle checked. It is recommended you
visit a NISSAN dealer for this service.

See “Intelligent Distance Control (I-DC)”
(P.5-89).

Engine oil pressure warning

light

This light warns of low engine oil pres-
sure. If the light flickers or comes on
during normal driving, pull off the road in
a safe area, stop the engine immediately
and call a NISSAN dealer or other author-
ized repair shop.

The engine oil pressure warning light is
not designed to indicate a low oil level.
Use the dipstick to check the oil level.
(See “Engine oil” (P.8-6).)

CAUTION

Running the engine with the engine
oil pressure warning light on could
cause serious damage to the engine
almost immediately. Such damage is
not covered by warranty. Turn off the
engine as soon as it is safe to do so.

Instruments and controls

2-13

2-14

Instruments and controls

Four-Wheel Drive (4WD) warn-

ing light (4WD models)

The

warning light comes on when the

ignition switch is placed in the ON posi-
tion. It turns off soon after the engine is
started.

If the 4WD system malfunctions, or the
diameter of the front and the rear wheels
are different, the warning light will either
remain illuminated or blink. (See “NISSAN
all-mode 4WD®” (P.5-121).)

CAUTION

. If the warning light comes on

while driving there may be a
malfunction in the 4WD system.
Reduce the vehicle speed and
have your vehicle checked as
soon as possible. It is recom-
mended you visit a NISSAN dealer
for this service.

. If the 4WD warning light turns on

when driving on dry or hard
surfaced roads:

— in the 4H(I) position, shift the

4WD shift switch to AUTO

— in the 4L(O) position, stop the

vehicle and shift the transmis-

sion shift lever to the N (Neu-
tral) position and shift the
4WD shift switch to AUTO

. If the warning light is still on after

the above operations, have your
vehicle checked as soon as pos-
sible. It is recommended you visit
a NISSAN dealer for this service.

Intelligent Cruise Control (ICC)

system warning light (orange)

This light comes on if there is a malfunc-
tion in the Intelligent Cruise Control (ICC)
system.

If the warning light comes on, park the
vehicle in a safe place. Turn the engine off,
restart the engine, resume driving and set
the ICC system again.

If it is not possible to set the system or
the indicator stays on, it may indicate
that the system is malfunctioning.
Although the vehicle is still driveable
under normal conditions, have the ve-
hicle checked. It is recommended you
visit a NISSAN dealer for this service.

Intelligent Key warning light

After the ignition switch is placed in the
ON position, this light comes on for about
2 seconds and then turns off.

This light warns of a malfunction with the
Intelligent Key system.

If the light comes on while the engine is
stopped, it may be impossible to start the
engine. If the light comes on while the
engine is running, you can drive the
vehicle. However in these cases, have
the system checked as soon as possible.
It is recommended you visit a NISSAN
dealer for this service.

Lane Departure Warning (LDW)

indicator light (orange; if so
equipped)

When the ignition switch is placed in the
ON position, the light will come on in
orange, turn green, and then turn off. This
indicates that the Lane Departure Warn-
ing (LDW) and Intelligent Lane Interven-
tion (I-LI) systems are operational.

While the LDW and/or I-LI system is on,
the light will blink in orange and a
warning chime will sound if the vehicle is
traveling close to either the left or the
right of a traveling lane with detectable
lane markers.

If the light comes on in orange and
remains on, it may indicate that the LDW
and I-LI systems are not functioning
properly. Although the vehicle is still
driveable, have the systems checked. It
is recommended you visit a NISSAN dealer
for this service.

See “Lane Departure Warning (LDW)/In-
telligent Lane Intervention (I-LI)” (P.5-23).

Low tire pressure warning

light

Your vehicle is equipped with a Tire
Pressure Monitoring System (TPMS) that
monitors the tire pressure of all tires
except the spare.

The low tire pressure warning light warns
of low tire pressure or indicates that the
TPMS is not functioning properly.

After the ignition switch is placed in the
ON position, this light illuminates for
about 1 second and turns off.

Low tire pressure warning:

If the vehicle is being driven with low tire
pressure, the warning light will illuminate.
A CHECK TIRE PRESSURE warning also
appears in the vehicle information dis-
play. If you select the tire pressure in-
formation in the center display, the Low
Pressure information will be displayed.

The tire pressure for each tire will also
be displayed.

When the low tire pressure warning light
illuminates, you should stop and adjust
the tire pressure to the recommended
COLD tire pressure shown on the Tire and
Loading Information label. The low tire
pressure warning light does not automa-
tically turn off when the tire pressure is
adjusted. After the tire is inflated to the
recommended pressure, the vehicle must
be driven at speeds above 16 MPH (25
km/h) to activate the TPMS and turn off
the low tire pressure warning light. Use a
tire pressure gauge to check the tire
pressure.

The CHECK TIRE PRESSURE warning ap-
pears each time the ignition switch is
placed in the ON position as long as the
low tire pressure warning light remains
illuminated.

For additional information, see “Vehicle
information display” (P.2-20), “Tire Pres-
sure Monitoring System (TPMS)” (P.5-5)
and “Tire Pressure Monitoring System
(TPMS) ” (P.6-3).

TPMS malfunction:

If the TPMS is not functioning properly,
the low tire pressure warning light will
flash for approximately 1 minute when the
ignition switch is placed in the ON posi-

tion. The light will remain on after 1
minute. Have the system checked. It is
recommended you visit a NISSAN dealer
for this service. The CHECK TIRE PRES-
SURE warning does not appear if the low
tire pressure warning light illuminates to
indicate a TPMS malfunction.

For additional information, see “Tire Pres-
sure Monitoring System (TPMS)” (P.5-5).

WARNING

. If the light does not illuminate

with the ignition switch placed in
the ON position, have the vehicle
checked as soon as possible. It is
recommended you visit a NISSAN
dealer for this service.

. If the light illuminates or Low

Pressure information is displayed
on the monitor screen while driv-
ing, avoid sudden steering man-
euvers or abrupt braking, reduce
vehicle speed, pull off the road to
a safe location and stop the
vehicle as soon as possible. Driv-
ing with under-inflated tires may
permanently damage the tires
and increase the likelihood of tire
failure. Serious vehicle damage
could occur and may lead to an

Instruments and controls

2-15

2-16

Instruments and controls

accident and could result in ser-
ious personal injury. Check the
tire pressure for all four tires.
Adjust the tire pressure to the
recommended COLD tire pressure
shown on the Tire and Loading
Information label to turn the low
tire pressure warning light OFF. If
the light still illuminates while
driving after adjusting the tire
pressure, a tire may be flat or
the TPMS may be malfunctioning.
If you have a flat tire, replace it
with a spare tire as soon as
possible. If no tire is flat and all
tires are properly inflated, it is
recommended you consult a
NISSAN dealer.

. Since the spare tire is not

equipped with the TPMS, when a
spare tire is mounted or a wheel
is replaced, the TPMS will not
function and the low tire pressure
warning light will flash for ap-
proximately 1 minute. The light
will remain on after 1 minute.
Have your tires replaced and/or
TPMS system reset as soon as
possible. It is recommended you
visit a NISSAN dealer for these
services.

. Replacing tires with those not

originally specified by NISSAN
could affect the proper operation
of the TPMS.

CAUTION

. The TPMS is not a substitute for

the regular tire pressure check.
Be sure to check the tire pressure
regularly.

. If the vehicle is being driven at

speeds of less than 16 MPH (25
km/h), the TPMS may not operate
correctly.

. Be sure to install the specified

size of tires to the four wheels
correctly.

Master warning light

When the ignition switch is in the ON
position, the master warning light illumi-
nates if any of the following are displayed
on the vehicle information display:
. No key warning

. Low fuel warning

. Low washer fluid warning

. Parking brake release warning

. Door/liftgate open warning

. Front radar obstruction warning

. Headlight warning

. Loose fuel cap warning

. Check tire pressure warning

. Intelligent Back-up Intervention (I-BI)

not available warning (if so equipped)

. Intelligent Back-up Intervention (I-BI)

malfunction warning (if so equipped)

. Automatic Emergency Braking (AEB)

system warning

. Extended storage fuse warning (if so

equipped)

See “Vehicle information display” (P.2-20).

Seat belt warning light and

chime

The light and chime remind you to fasten
seat belts. The light illuminates whenever
the ignition switch is placed in the ON
position, and will remain illuminated until
the driver’s seat belt is fastened. At the
same time, the chime will sound for about
6 seconds unless the driver’s seat belt is
securely fastened.

The seat belt warning light for the front
passenger will illuminate if the seat belt is
not fastened when the front passenger’s
seat is occupied. For approximately 5

seconds after the ignition switch is placed
in the ON position, the system does not
activate the warning light for the front
passenger.

See “Seat belts” (P.1-20) for precautions on
seat belt usage.

Supplemental air bag warning

light

After placing the ignition switch in the ON
position, the supplemental air bag warn-
ing light will illuminate. The supplemental
air bag warning light will turn off after
about 7 seconds if the air bag and/or
pretensioner systems are operational.

If any of the following conditions occur,
the air bag and/or pretensioner systems
needs servicing.
. The supplemental air bag warning

light remains on after approximately
7 seconds.

. The supplemental air bag warning

light flashes intermittently.

. The supplemental air bag warning

light does not come on at all.

It is recommended you visit a NISSAN
dealer for these services.

Unless checked and repaired, the supple-
mental restraint system (air bag system)
and/or the pretensioners may not func-

tion properly.

For additional information, see “Supple-
mental restraint system” (P.1-55).

WARNING

If the supplemental air bag warning
light is on, it could mean that the
front air bag, side air bag, curtain air
bag systems and/or pretensioner
systems will not operate in an acci-
dent. To help avoid injury to yourself
or others, have your vehicle checked.
It is recommended you visit a NISSAN
dealer for this service.

Vehicle Dynamic Control (VDC)

warning light

When the ignition switch is in the ON
position, the Vehicle Dynamic Control
(VDC) warning light illuminates and then
turns off.

The light will blink when the VDC system
or the traction control system is operat-
ing, thus alerting the driver that the
vehicle is nearing its traction limits. The
road surface may be slippery.

When the VDC warning light illuminates
when the VDC system is turned on, this

light alerts the driver to the fact that the
VDC system’s fail-safe mode is operating,
for example the VDC or hill start assist
system may not be functioning properly.
Have the system checked. It is recom-
mended you visit a NISSAN dealer for this
service. If a malfunction occurs in the
system, the VDC system function will be
canceled but the vehicle is still driveable.
For additional information, see “Vehicle
Dynamic Control (VDC) system” (P.5-138).

INDICATOR LIGHTS

Automatic Transmission (AT)

position indicator light

When the ignition switch is placed in the
ON position, the indicator shows the shift
lever position.

In the manual shift mode, when the
transmission does not shift to the se-
lected gear due to a transmission protec-
tion mode, the AT position indicator light
will blink and a buzzer will sound.

See “Automatic transmission” (P.5-18) for
further details.

Instruments and controls

2-17

2-18

Instruments and controls

Intelligent Blind Spot Inter-

vention (I-BSI) ON indicator light
(green; if so equipped)

The light comes on in green when the
Intelligent Blind Spot Intervention (I-BSI)
system is turned on. The light turns off
when the system is turned off.

NOTE:

This light is common with the BSW/I-BSI
system warning light (orange). (See
“Blind Spot Warning (BSW)/Intelligent
Blind Spot Intervention (I-BSI) system
warning light” (P.2-12).)

For more details, see “Intelligent Blind
Spot Intervention (I-BSI)” (P.5-43).

Check suspension indicator

light

When the ignition switch is placed in the
ON position, the light comes on for 2
seconds.

Exterior light indicator

This indicator illuminates when the head-
light switch is turned to the AUTO,

position and the front parking lights,

instrument panel lights, rear combination
lights, license plate lights or headlights
are on. The indicator turns off when these

lights are turned off.

Front fog light indicator light

(if so equipped)

The front fog light indicator light illumi-
nates when the front fog lights are on.
(See “Fog light switch” (P.2-42).)

Front passenger air bag sta-

tus light

The front passenger air bag status light
(

) located on the instrument panel will

be lit and the passenger front air bag will
be OFF depending on how the front
passenger seat is being used.

For front passenger air bag status light
operation, see “NISSAN Advanced Air Bag
System (front seats)” (P.1-61).

High beam indicator light

This light comes on when the headlight
high beam is on and goes out when the
low beam is selected.

Intelligent Lane Intervention (I-

LI) ON indicator light (green; if so
equipped)

The light comes on in green when the
Intelligent Lane Intervention (I-LI) system
is turned on. The light turns off when the
system is turned off.

NOTE:

This light is common with the Lane
Departure Warning (LDW) indicator light
(orange). (See “Lane Departure Warning
(LDW) indicator light” (P.2-14).)

For more details, see “Lane Departure
Warning (LDW)/Intelligent Lane Interven-
tion (I-LI)” (P.5-23).

Malfunction Indicator Light

(MIL)

If the malfunction indicator light comes
on steady or blinks while the engine is
running, it may indicate a potential emis-
sion control malfunction.

The malfunction indicator light may also
come on steady if the fuel-filler cap is
loose or missing, or if the vehicle runs out
of fuel. Check to make sure the fuel-filler
cap is installed and closed tightly, and
that the vehicle has at least 3 US gallons
(14 liters) of fuel in the fuel tank.

After a few driving trips, the

light

should turn off if no other potential
emission control system malfunction ex-
ists.

If this indicator light remains on for 20
seconds and then blinks for 10 seconds
when the engine is not running, it indi-
cates that the vehicle is not ready for an
emission control system inspection/
maintenance test. (See “Readiness for
Inspection/Maintenance (I/M) test” (P.10-
32).)

Operation:

The malfunction indicator light will come
on in one of two ways:
. Malfunction indicator light on steady

— An emission control system mal-
function has been detected. Check
the fuel-filler cap if the LOOSE FUEL
CAP warning appears in the vehicle
information display. If the fuel-filler
cap is loose or missing, tighten or
install the cap and continue to drive
the vehicle. The

light should turn

off after a few driving trips. If the
light does not turn off after a few
driving trips, have the vehicle in-
spected. It is recommended you visit
a NISSAN dealer for this service. You
do not need to have your vehicle
towed to the dealer.

. Malfunction indicator light blinking —

An engine misfire has been detected
which may damage the emission
control system.
To reduce or avoid emission control
system damage:
1) Do not drive at speeds above 45

MPH (72 km/h).

2) Avoid hard acceleration or decel-

eration.

3) Avoid steep uphill grades.
4) If possible, reduce the amount of

cargo being hauled or towed.

The malfunction indicator light may
stop blinking and remain on.
Have the vehicle inspected. It is re-
commended you visit a NISSAN dealer
for this service. You do not need to
have your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could lead to poor driveability, re-
duced fuel economy, and possible
damage to the emission control sys-
tem.

Security indicator light

The light blinks when the ignition switch
is in the ACC, OFF and LOCK position. This
function indicates the security system
equipped on the vehicle is operational.

If the security system is malfunctioning,
this light will remain on while the ignition
switch is in the ON position. For additional
information, see “Security systems” (P.2-
30).

SNOW mode indicator light

When selecting SNOW mode while the
engine is running, this light will illuminate.
(See “SNOW mode” (P.5-132).)

TOW mode indicator light

This light will illuminate when the TOW
MODE is selected while the engine is
running. (See “TOW mode” (P.5-131).)

Turn signal/hazard indicator

lights

The light flashes when the turn signal
switch lever or hazard switch is turned on.

Instruments and controls

2-19

2-20

Instruments and controls

Vehicle Dynamic Control (VDC)

off indicator light

When the ignition switch is in the ON
position, the Vehicle Dynamic Control
(VDC) off indicator light illuminates and
then turns off.

The light comes on when the VDC off
switch is pushed to OFF. This indicates
that the VDC system is not operating.

When the 4L position is selected with the
Four-Wheel Drive (4WD) shift switch, the
VDC system is disabled and the VDC off
indicator light illuminates. (4WD models)

For additional information, see “Vehicle
Dynamic Control (VDC) system” (P.5-138).

AUDIBLE REMINDERS

Key reminder chime

A chime will sound if the driver side door
is opened while the ignition switch is
placed in the ACC position. Make sure
the ignition switch is placed in the OFF
position, and take the Intelligent Key with
you when leaving the vehicle.

Light reminder chime

A chime will sound when the driver side
door is opened with the light switch in the

position and the ignition

switch in the ACC, OFF or LOCK position.

Turn the light switch off when you leave
the vehicle.

Parking brake reminder chime

The chime will sound if the vehicle is
driven at more than 4 MPH (7 km/h) with
the parking brake applied. Stop the vehi-
cle and release the parking brake.

Brake pad wear warning

The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first
occur only when the brake pedal is
depressed. After more wear of the brake
pad, the sound will always be heard even
if the brake pedal is not depressed. Have
the brakes checked as soon as possible if
the warning sound is heard.

SIC4379

The vehicle information display

located

between the speedometer and odometer,
and shows the indicators for the driving
systems, Intelligent Key operation and
various warnings and information.

For detailed information about each sys-
tem, see the following sections:
. Automatic Transmission (AT)

— “Warning lights, indicator lights and

audible reminders” (P.2-10).

— “Driving the vehicle” (P.5-17).

. Four-Wheel Drive (4WD)

— “NISSAN all-mode 4WD®” (P.5-121).

. Intelligent Back-up Intervention (I-BI)

VEHICLE INFORMATION DISPLAY

— “Intelligent Back-up Intervention (I-

BI)” (P.5-57).

. Intelligent Cruise Control (ICC)

— “Intelligent Cruise Control (ICC)”

(P.5-67).

. Intelligent Distance Control (I-DC)

— “Intelligent Distance Control (I-DC)”

(P.5-89).

. Intelligent Key system

— “Intelligent Key system” (P.3-7).
— “Push-button ignition switch” (P.5-

13).

. Automatic Emergency Braking (AEB)

— “Automatic Emergency Braking

(AEB)” (P.5-102).

. Intelligent Forward Collision Warning

(I-FCW)
— “Intelligent Forward Collision Warn-

ing (I-FCW)” (P.5-111).

Instruments and controls

2-21

OPERATIONAL INDICATORS

1. Engine start operation indicator

This indicator appears when the shift
lever is in the P (Park) position.

This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed.

2. NO KEY warning

This warning appears in either of the
following conditions.

No key inside the vehicle:

The warning appears when the door is
closed with the Intelligent Key left outside
the vehicle and the ignition switch in the
ACC or ON position. Make sure that the
Intelligent Key is inside the vehicle.

Unregistered Intelligent Key:

The warning appears when the ignition
switch is pushed from the LOCK position
and the Intelligent Key cannot be recog-
nized by the system. You cannot start the
engine with an unregistered key. Use the
registered Intelligent Key.

See “Intelligent Key system” (P.3-7) for
more details.

3. SHIFT “P” warning

This warning appears when the ignition
switch is pushed to stop the engine with
the shift lever in any position except the P
(Park) position.

If this warning appears, move the shift
lever to the P (Park) position or push the
ignition switch to the ON position.

An inside warning chime will also sound.
(See “Intelligent Key system” (P.3-7).)

4. “PUSH” warning

This warning appears when the shift lever
is moved to the P (Park) position with the
ignition switch in the ACC position after
the SHIFT “P” warning appears.

To push the ignition switch to the OFF
position, perform the following proce-
dure:

SHIFT “P” warning

? (Move the shift lever

to “P”)

? PUSH warning ? (Push the

ignition switch

? ignition switch position

is turned to ON)

? PUSH warning ?

(Push the ignition switch

? ignition

switch position is turned to OFF)

5. Intelligent Key battery discharge
indicator

This indicator appears when the Intelli-
gent Key battery is running out of power.

If this indicator appears, replace the
battery with a new one. (See “Intelligent
Key battery replacement” (P.8-21).)

6. Engine start operation for Intelli-
gent Key system indicator

This indicator appears when the Intelli-
gent Key battery is running out of power
and when the Intelligent Key System and
vehicle are not communicating normally.

If this indicator appears, touch the igni-
tion switch with the Intelligent Key while
depressing the brake pedal. (See “Intelli-
gent Key battery discharge” (P.5-15).)

7. Remote engine start indicator (if
so equipped)

This indicator appears when the engine
has been started using the remote engine
start function. To start the vehicle, de-
press the brake pedal and place the
ignition switch in the ON position.

For more details, see “Remote engine
start” (P.3-19).

Instruments and controls

2-23

2-24

Instruments and controls

8. Parking brake release warning

This warning appears when the vehicle
speed is above 4 MPH (7 km/h) and the
parking brake is applied.

9. Low fuel warning

This warning appears when the fuel level
in the tank is getting low. Refuel as soon
as it is convenient, preferably before the
fuel gauge reaches the 0 (Empty) position.

There is a small reserve of fuel remain-
ing in the tank when the fuel gauge
reaches the 0 (Empty) position.

10. Low washer fluid warning

This warning appears when the washer
tank fluid is at a low level. Add washer
fluid as necessary. (See “Window washer
fluid” (P.8-10).)

11. Door/liftgate open warning
(ignition switch is in the ON posi-
tion)

This warning appears if any of the doors
and/or the liftgate are open or not closed
securely. The vehicle icon indicates which
door or the liftgate is open on the display.

12. Loose fuel cap warning

This warning appears when the fuel-filler
cap is not tightened correctly after the
vehicle has been refueled. (See “Fuel-filler
cap” (P.3-27).)

13. Check tire pressure warning

This warning appears when the low tire
pressure warning light in the meter
illuminates and low tire pressure is de-
tected. The warning appears each time
the ignition switch is placed in the ON
position as long as the low tire pressure
warning light remains illuminated. If this
warning appears, stop the vehicle and
adjust the tire pressure to the recom-
mended COLD tire pressure shown on the
Tire and Loading Information label. (See
“Low tire pressure warning light” (P.2-15)
and “Tire Pressure Monitoring System
(TPMS)” (P.5-5).)

14. Extended storage fuse warning
(if so equipped)

This warning may appear if the extended
storage fuse switch is not pushed in
(switched on). When this warning ap-
pears, push in (switch on) the extended
storage fuse switch to turn off the warn-
ing. For more information, see “Extended
storage fuse switch” (P.8-21).

15. Intelligent Back-up Intervention
(I-BI) not available warning (if so
equipped)

This warning appears when the Intelli-
gent Back-up Intervention (I-BI) system is
temporarily not available.

For more details, see “Intelligent Back-up
Intervention (I-BI)” (P.5-57).

16. Intelligent Back-up Intervention
(I-BI) malfunction warning (if so
equipped)

This warning appears when the Intelli-
gent Back-up Intervention (I-BI) system is
not functioning properly.

For more details, see “Intelligent Back-up
Intervention (I-BI)” (P.5-57).

17. Headlight warning

This warning appears if the LED head-
lights are malfunctioning. It is recom-
mended you have the system checked
by a NISSAN dealer.

18. Front radar obstruction warning

This warning appears when the sensor
area of the front bumper is covered with
dirt or is obstructed, making it impossible
to detect a vehicle ahead.

The following systems will be automati-
cally canceled.

. Intelligent Cruise Control (ICC) system

. Intelligent Distance Control (I-DC) sys-

tem (if so equipped)

. Automatic Emergency Braking (AEB)

system

. Intelligent Forward Collision Warning

(I-FCW) system

For more details, see “Intelligent Cruise
Control (ICC)” (P.5-67), “Intelligent Distance
Control (I-DC)” (P.5-89), “Automatic Emer-
gency Braking (AEB)” (P.5-102) or “Intelli-
gent Forward Collision Warning (I-FCW)”
(P.5-111).

19. “TIMER” indicator

This indicator appears when the set
“TIMER” indicator activates. You can set
the time for up to 6 hours. (See “Trip
computer” (P.2-28).)

20. Low outside temperature
warning

This warning appears if the outside tem-
perature is below 37°F (3°C). The warning
can be set not to be displayed. (See “Trip
computer” (P.2-28).)

21. Four-Wheel Drive (4WD) shift
indicator (4WD models)

This indicator shows the Four-Wheel
Drive (4WD) driving mode (AUTO, 4HI or
4LO) that is selected by the 4WD shift
switch. (See “NISSAN all-mode 4WD®” (P.5-
121).)

22. Intelligent Cruise Control (ICC)
system MAIN switch indicator

The Intelligent Cruise Control (ICC) sys-
tem main switch indicator (CRUISE) is
displayed when the ICC main switch is
pushed. When the main switch is pushed
again, the indicator disappears. While the
CRUISE indicator is displayed, the ICC
system is operational.

The cruise control set indicator (SET) is
displayed while the vehicle is controlled
by the conventional (fixed speed) cruise
control mode of the ICC system.

For more details, see “Intelligent Cruise
Control (ICC)” (P.5-67).

23. Intelligent Distance Control (I-
DC) system switch indicator (if so
equipped)

The indicator is displayed when the
Intelligent Distance Control (I-DC) system
switch is pushed on. When the switch is
pushed again, the indicator disappears.

While the indicator is displayed, the I-DC
system is operational. (See “Intelligent
Distance Control (I-DC)” (P.5-89).)

24. Intelligent Back-up Intervention
(I-BI) system indicator (if so
equipped)

The I-BI ON indicator (SYSTEM ON) ap-
pears when the shift lever is in the R
(Reverse) position with the Intelligent
Back-up Intervention (I-BI) system turned
on.

If the I-BI system is turned off, the I-BI OFF
indicator (SYSTEM OFF) appears.

For more details, see “Intelligent Back-up
Intervention (I-BI)” (P.5-57).

25. Rear door alert is activated

When the rear door alert system is
enabled, this message appears when the
rear door alert system is active and can
remind the driver to check the rear seat.

NOTE:

This system is disabled until a driver
enables it using the rear door alert
switch.

For more details, see “Rear door alert”
(P.2-49).

Instruments and controls

2-25

2-26

Instruments and controls

26. Check back seat for all articles

When the rear door alert system is
enabled, this message appears when the
vehicle comes to a complete stop, the
shift lever is moved from the D (Drive) or R
(Reverse) position to P (Park) position, and
the driver exits the vehicle. This message
alerts the driver, after a period of time, to
check for items in the rear seat after the
audible alert has been provided.

NOTE:

This rear door alert system is disabled
until a driver enables it using the rear
door alert switch.

For more details, see “Rear door alert”
(P.2-49).

SIC4325

MAINTENANCE INDICATORS

1. Engine oil replacement indicator

This indicator appears when the custo-
mer set time comes for changing the
engine oil. You can set or reset the
distance for changing the engine oil.
(See “Trip computer” (P.2-28).)

2. Oil filter replacement indicator

This indicator appears when the custo-
mer set time comes for replacing the oil
filter. You can set or reset the distance for
replacing the oil filter. (See “Trip compu-
ter” (P.2-28).)

3. Tire replacement indicator

This indicator appears when the custo-
mer set distance comes for replacing
tires. You can set or reset the distance
for replacing tires. (See “Trip computer”
(P.2-28).)

WARNING

The tire replacement indicator is not
a substitute for regular tire checks,
including tire pressure checks. See
“Changing wheels and tires” (P.8-37).
Many factors including tire inflation,
alignment, driving habits and road
conditions affect tire wear and when

tires should be replaced. Setting the
tire replacement indicator for a cer-
tain driving distance does not mean
your tires will last that long. Use the
tire replacement indicator as a guide
only and always perform regular tire
checks. Failure to perform regular
tire checks, including tire pressure
checks could result in tire failure.
Serious vehicle damage could occur
and may lead to a collision, which
could result in serious personal in-
jury or death.

4. “OTHER” indicator

This indicator appears when the custo-
mer set time comes for replacing items
other than the engine oil, oil filter and
tires. You can set or reset the distance for
replacing the items. (See “Trip computer”
(P.2-28).)

More maintenance reminders are also
available on the center display. (See
NissanConnect® Owner’s Manual.)

SIC4494

Instruments and controls

2-27

2-28

Instruments and controls

SIC4420

TRIP COMPUTER

Switches for the trip computer are lo-
cated on the right side of the combina-
tion meter panel. To operate the trip
computer, push the switches as shown
above.

switch

When the ignition switch is pushed to the
ON position, modes of the trip computer
can be selected by pushing the
switch

Each time the

switch

is pushed, the

display will change as follows:

Current fuel consumption

? Average fuel

consumption and speed

? Elapsed time

and trip odometer

? Distance to empty

(dte)

? Outside air temperature (ICY) ?

Setting

? Warning check

1. Current and average fuel con-
sumption

The current and average fuel consump-
tion mode shows the current and aver-
age fuel consumption.

2. Average fuel consumption (MPG
or l (liter)/100 km) and speed (MPH
or km/h)

Fuel consumption:

The average fuel consumption mode
shows the average fuel consumption
since the last reset. Resetting is done by
pushing the

switch

for longer than

1 second. (The average speed is also reset
at the same time.)

The display is updated every 30 seconds.
At about the first 1/3 mile (500 m) after a
reset, the display shows “——”.

Speed:

The average speed mode shows the
average vehicle speed since the last reset.
Resetting is done by pushing the
switch

for longer than 1 second. (The

average fuel consumption is also reset at
the same time.)

The display is updated every 30 seconds.
The first 30 seconds after a reset, the
display shows “——”.

3. Elapsed time and trip odometer
(MILES or km)

Elapsed time:

The elapsed time mode shows the time
since the last reset. The displayed time
can be reset by pushing the

switch

for longer than 1 second. (The trip od-
ometer is also reset at the same time.)

Trip odometer:

The trip odometer mode shows the total
distance the vehicle has been driven since
the last reset. Resetting is done by push-
ing the

switch

for longer than 1

second. (The elapsed time is also reset at
the same time.)

4. Distance to empty (dte — MILES
or km)

The distance to empty (dte) mode pro-
vides you with an estimation of the
distance that can be driven before refuel-
ing. The dte is constantly being calcu-
lated, based on the amount of fuel in the
fuel tank and the actual fuel consump-
tion.

The display is updated every 30 seconds.

The dte mode includes a low range

Nissan Armada (2019 year). Instruction - part 7