Nissan Altima L32. Manual - part 1324

SEC-446

< COMPONENT DIAGNOSIS >

[SEDAN WITHOUT INTELLIGENT KEY]

B210C STARTER CONTROL RELAY

B210C STARTER CONTROL RELAY

Description

INFOID:0000000004499094

Starter control relay, integrated in IPDM E/R, permits the starter relay operation when in N or P position and

the steering is locked or unlocked. It is installed in parallel with the starter relay.

DTC Logic

INFOID:0000000004499095

DTC DETECTION LOGIC

NOTE:

• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-433, "DTC Logic"

.

• If DTC B210C is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-434, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn the power supply position to start under the following conditions and wait for at least 1 second.

-

CVT selector lever is in the P or N position.

-

Depress the brake pedal

2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?

YES

>> Refer to 

SEC-446, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000004499096

1.

INSPECTION START

1. Turn ignition switch ON.

2. Check “Self diagnostic result” with CONSULT-III.

3. Touch “ERASE”.

4. Perform DTC Confirmation Procedure.

Refer to 

PCS-45, "DTC Index"

.

Is the DTC B210C displayed again?

YES

>> Replace IPDM E/R. Refer to 

PCS-48, "Removal and Installation"

.

NO

>> Inspection End.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B210C

START CONT RLY 
OFF

IPDM E/R detects that the relay is stuck at ON po-
sition even if the following conditions are met for 
about 1 second.
• Starter control relay ON/OFF signal from BCM
• Shift park neutral position (PNP) switch input sig-

nal

• IPDM E/R

B210D STARTER RELAY

SEC-447

< COMPONENT DIAGNOSIS >

[SEDAN WITHOUT INTELLIGENT KEY]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210D STARTER RELAY

Description

INFOID:0000000004499097

Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition

switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication.

DTC Logic

INFOID:0000000004499098

DTC DETECTION LOGIC

NOTE:

• If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-433, "DTC Logic"

.

• If DTC B210D is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-434, "DTC Logic"

.

• If DTC B210D is displayed with DTC B2617, first perform the trouble diagnosis for DTC B2617. Refer to

SEC-496, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Ignition switch ON under the following conditions and wait for at least 1 second.

-

CVT selector lever is in the P or N position

-

Do not depress the brake pedal

2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?

YES

>> Refer to 

SEC-447, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000004499099

1.

CHECK STARTER RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R harness connector.

3. Check voltage between IPDM E/R harness connector and

ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-48, "Removal and

Installation"

.

NO

>> Check harness for open or short between IPDM E/R and

battery.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B210D

STARTER RELAY 
ON

IPDM E/R detects that the relay is stuck at ON po-
sition even if the following conditions are met for 
about 1 second.
• Starter control relay ON/OFF signal from BCM
• Shift park neutral position (PNP) switch input

• IPDM  E/R

IPDM E/R

Ground

Voltage (V)

Connector

Terminal

E18

36

Ground

Battery voltage

ALKIA1319ZZ

SEC-448

< COMPONENT DIAGNOSIS >

[SEDAN WITHOUT INTELLIGENT KEY]

B210E STARTER RELAY

B210E STARTER RELAY

Description

INFOID:0000000004499100

Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition

switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication.

DTC Logic

INFOID:0000000004499101

DTC DETECTION LOGIC

NOTE:

• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-433, "DTC Logic"

.

• If DTC B210E is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-434, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions and wait for at least 1 second.

-

CVT selector lever is in the P or N position

-

Do not depress the brake pedal

2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?

YES

>> Refer to 

SEC-448, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000004499102

1.

CHECK STARTER RELAY OUTPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect BCM harness connector.

3. Check voltage between BCM harness connector and ground.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B210E

STARTER RELAY 
OFF

IPDM E/R detects that the relay is stuck at ON posi-
tion even if the following conditions are met for about 
1 second.
• Starter control relay ON/OFF signal from BCM
• Shift park neutral position (PNP) switch input

• IPDM E/R

ALKIA0452ZZ

BCM connector

Ground

Condition

Voltage (V)

Connector

Terminal

Ignition switch

Brake pedal

CVT selector lever

M21

132

Ground

ON

Depressed

P or N

Battery voltage

Other than above

0

B210E STARTER RELAY

SEC-449

< COMPONENT DIAGNOSIS >

[SEDAN WITHOUT INTELLIGENT KEY]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Is the inspection result normal?

YES

>> GO TO 3

NO

>> GO TO 2

2.

CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT

1. Disconnect IPDM E/R harness connector.

2. Check continuity between IPDM E/R harness connector and

BCM harness connector.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-48, "Removal and Installation"

.

NO

>> Repair harness connector.

3.

CHECK STARTER RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R harness connector.

3. Check voltage between IPDM E/R harness connector and

ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-48, "Removal and

Installation"

.

NO

>> Check harness for open or short between IPDM E/R and

battery.

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

A: E17

46

B: M21

132

Yes

IPDM E/R

Ground

Continuity

Connector

Terminal

A: E17

46

Ground

No

ALKIA1318ZZ

IPDM E/R

Ground

Voltage (V)

Connector

Terminal

E17

46

Ground

Battery voltage

ALKIA1320ZZ