Nissan Altima L32. Manual - part 1203

SE-22

< ON-VEHICLE REPAIR >

[COUPE]

FRONT SEAT

PASSENGER'S SEAT

13. Power seat outer finisher

14. Seat switch assembly 

15. Seat slide switch  

16. Seat reclining switch 

17. Recline lever finisher 

18. Manual seat recline lever

19. Manual seat outer lower finisher 

20. Manual seat outer finisher 

21. Manual slide cover

22. Power rear leg covers

23. Entry knob

24. Bezel

1.

Headrest

2.

Headrest holder (locked)

3.

Headrest holder (free)

4.

Seatback board 

5.

Rear leg covers

6.

Clip harness

7.

Outer finisher

8.

Seatback lever

9.

Power seat harness

10. Seatback/frame assembly

11. Front leg covers 

12. Seat cushion assembly

ALIIA0240GB

FRONT SEAT

SE-23

< ON-VEHICLE REPAIR >

[COUPE]

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

Removal and Installation

INFOID:0000000004206791

REMOVAL

CAUTION:

• Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and

wait and least 3 minutes.

• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-

tor with the side air bag module connector. Such an error may cause the air bag to deploy.

• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with

care.

• After front side air bag module inflates, front seatback assembly must be replaced.

• Always replace passenger seat cushion as an assembly with Occupant Classification System.

• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.

• When removing and installing, use shop cloths to protect the parts from damage where they may

interfere with other parts.

1. Slide the seat until the four seat bolts are visible and a tool can be inserted.
2. Disconnect the negative and positive battery terminals and wait at least 3 minutes.
3. Disconnect the harness connector for the side air bag module.
4. Disconnect the power seat harness connector and vehicle harness clip from the vehicle.
5. Remove the seat leg covers.
6. Remove the four seat bolts.

INSTALLATION

Installation is in the reverse order of removal.

• When installing the LH front seats tighten the bolts as shown.

• When installing the RH front seats tighten the bolts as shown.

13. SRS seat harness

14. Inner finisher

15. Seat belt buckle

16. Release handle

17. Release handle cover

18. Kick lever

LIIA2853E

LIIA2854E

SE-24

< ON-VEHICLE REPAIR >

[COUPE]

REAR SEAT

REAR SEAT

Exploded View

INFOID:0000000004206792

SPLIT REAR SEAT

1.

Release strap

2.

Rear seat lock assembly

3.

Rear striker assembly

4.

Rear seatback reinforcement

5.

LH seatback frame

6.

RH seatback frame

7.

RH seatback pad

8.

LH seatback pad

9.

RH seatback trim

10. LH seatback trim

11. RH seatback hinge assembly

12. Seat cushion trim

13. Seat cushion pad

14. LH seatback hinge assembly

ALIIA0215GB

REAR SEAT

SE-25

< ON-VEHICLE REPAIR >

[COUPE]

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

Removal and Installation

INFOID:0000000004206793

REMOVAL

1. Remove the rear seat cushion trim and pad.

• Pull the seat cushion upward to release the wire from the plastic hook, then pull the seat cushion for-

ward to remove.

2. Remove the seat belt webbing from the guides.
3. Remove the seatback hinge anchor bolts and nut.
4. Remove the seatback assemblies.

INSTALLATION

Installation is in the reverse order of removal.