Nissan Versa Sedan. Manual - part 193

DLK-90

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DOOR SWITCH

3. Check continuity between door switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-69, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR SWITCH 

Refer to 

DLK-90, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace malfunctioning door switch.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000009268772

1.

CHECK DOOR SWITCH

1. Turn ignition switch OFF.

2. Disconnect malfunctioning door switch connector.

3. Check continuity between door switch terminals.

Is the inspection result normal?

Door switch

BCM

Continuity 

Connector

Terminal

Connector

Terminal

Front door switch 
LH

B8

3

M100

47

Yes

Front door switch 
RH

B16

45

Rear door switch  
LH

B6

48

Rear door switch 
RH

B17

46

Door switch

Ground

Continuity 

Connector

Terminal

Front door switch LH

B8

3

No

Front door switch RH

B16

Rear door switch LH

B6

Rear door switch RH

B17

Door switch

Condition

Continuity

Terminal

Front door switch 
LH

3

Ground part of door 

switch

Door switch

Pressed

No

Released

Yes

Front door switch 
RH

Pressed

No

Released

Yes

Rear door switch 
LH

Pressed

No

Released

Yes

Rear door switch 
RH

Pressed

No

Released

Yes

DOOR SWITCH

DLK-91

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

YES

>> Inspection End.

NO

>> Replace malfunction door switch.

DLK-92

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

HAZARD FUNCTION

HAZARD FUNCTION

Component Function Check

INFOID:0000000009268773

1.

CHECK FUNCTION

1. Select INTELLIGENT KEY of BCM using CONSULT.

2. Select FLASHER in ACTIVE TEST mode.

3. Touch LH or RH to check that it works normally.
Is the inspection result normal?

YES

>> Hazard warning lamp circuit is OK.

NO

>> Refer to 

DLK-92, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009268774

1.

CHECK HAZARD SWITCH CIRCUIT

Refer to 

EXL-87, "Component Function Check"

. 

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> Inspection End.

INTELLIGENT KEY

DLK-93

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INTELLIGENT KEY

Component Function Check

INFOID:0000000009268775

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II

User Guide for additional information.

• Check Intelligent Key relative signal strength.

• Confirm vehicle Intelligent Key antenna signal strength.

1.

CHECK FUNCTION

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “RKE OPE COUN1” in “DATA MONITOR” mode.

3. Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Intelligent Key is OK.

NO

>> Refer to 

DLK-93, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009268776

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II

User Guide for additional information.

• Check Intelligent Key relative signal strength.

• Confirm vehicle Intelligent Key antenna signal strength.

1.

CHECK INTELLIGENT KEY BATTERY

Check by connecting a resistance (approximately 300

Ω) so that the

current value becomes about 10 mA. Refer to 

DLK-189, "Removal

and Installation"

.

Is the measurement value within the specification?

YES

>> Replace Intelligent Key. 

NO

>> Replace Intelligent Key battery.

Monitor item

Condition

RKE OPE COUN1

Check that the numerical value is changing while operating on the Intelligent Key.

Standard

: Approx. 2.5 - 3.0V

OCC0607D