Nissan Note E12. Manual - part 685

WCS

THE LIGHT REMINDER WARNING DOES NOT SOUND

WCS-35

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE LIGHT REMINDER WARNING DOES NOT SOUND

Description

INFOID:0000000009541248

Light reminder warning chime does not sound even though headlamps are illuminated.

Diagnosis Procedure

INFOID:0000000009541249

1.

CHECK COMBINATION METER INPUT SIGNAL

Select the Data Monitor for the METER/M&A and check the BUZZER monitor value.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-48, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT

Check the driver side door switch signal circuit. Refer to 

DLK-84, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK DRIVER SIDE DOOR SWITCH

Check the driver side door switch. Refer to 

DLK-85, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace the BCM. Refer to 

BCS-67, "Removal and Installation"

.

NO

>> Replace driver side door switch. Refer to 

DLK-158, "Removal and Installation"

.

Monitor Item

Condition

Status

BUZZER

Under the condition of buzzer input

ON

Except above

OFF

WT-1

SUSPENSION

C

D

F

G

H

I

J

K

L

M

SECTION 

WT

A

B

WT

N

O

P

CONTENTS

ROAD WHEELS & TIRES

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

2

Service Notice and Precautions for Road Wheel ......

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Commercial Service Tool  ..........................................

3

PERIODIC MAINTENANCE ..........................

4

WHEEL ................................................................

4

Inspection ..................................................................

4

WHEEL AND TIRE .............................................

5

Adjustment ................................................................

5

REMOVAL AND INSTALLATION ................

8

WHEEL AND TIRE .............................................

8

Exploded View ..........................................................

8

Removal and Installation  ..........................................

8

SERVICE DATA AND SPECIFICATIONS 
(SDS) .............................................................

9

SERVICE DATA AND SPECIFICATIONS 
(SDS) ..................................................................

9

Wheel .......................................................................

9

Tire Air Pressure .......................................................

9

WT-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000009445894

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

types of collision. Information necessary to service the system safely is included in the SR and SB section of

this Service Manual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by

an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a

hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

serious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

battery and wait at least three minutes before performing any service.

Service Notice and Precautions for Road Wheel

INFOID:0000000009443478

• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.

• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.

• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-

num wheel weights.

• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing

dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-

gent if a detergent is needed.

• After driving on roads scattered with anti-icing salts, wash off the wheels completely.

• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them

from being trapped between the contact surfaces of wheel.

• Do not apply oil to nut and bolt threads.

• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.

PREPARATION

WT-3

< PREPARATION >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

PREPARATION

PREPARATION

Commercial Service Tool

INFOID:0000000009443480

Tool name

Description

Power tool

Loosening nuts, screws and bolts

PIIB1407E