Nissan Rogue. Manual - part 326

DLK-146

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2622 INSIDE ANTENNA

B2622 INSIDE ANTENNA

DTC Logic

INFOID:0000000011278855

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “INSIDE ANT DIAGNOSIS” in “Work support”.

3. Perform inside key antenna (“INSIDE ANT DIAGNOSIS”) on “Work support” of “INTELLIGENT KEY”.

4. Check BCM for DTC.
Is inside key antenna DTC detected?

YES

>> Refer to 

DLK-146, "Diagnosis Procedure"

.

NO

>> Inside key antenna (console) is OK.

Diagnosis Procedure

INFOID:0000000011278856

Regarding Wiring Diagram information, refer to 

DLK-73, "Wiring Diagram"

.

1.

CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1

1. Turn ignition switch OFF.

2. Check signal between BCM harness connector and ground using oscilloscope.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

NO

>> GO TO 2.

DTC

CONSULT display 

description

DTC detecting condition

Possible cause

B2622

INSIDE ANTENNA

An excessive high or low voltage from inside anten-
na (console) is sent to BCM.

• Inside key antenna (console)
• Harness or connector

[Inside key antenna (console) cir-
cuit is open or shorted]

(+)

(–)

Condition

Signal

(Reference value)

BCM

Connector

Terminal

B16

62, 63

Ground

When Intelligent Key is in the an-
tenna detection area.

When Intelligent Key is not in the 
antenna detection area.

JMKIA3839GB

JMKIA5951GB

2015 Rogue NAM

B2622 INSIDE ANTENNA

DLK-147

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

2.

CHECK INSIDE KEY ANTENNA CIRCUIT

1. Disconnect BCM connector and inside key antenna (console) connector.

2. Check continuity between BCM harness connector and inside key antenna (console) harness connector.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2

1. Replace inside key antenna (console). (New antenna or other antenna)

2. Connect BCM connector and inside key antenna (console) connector.

3. Check signal between BCM harness connector and ground using oscilloscope.

Is the inspection result normal?

YES

>> Replace inside key antenna (console). Refer to 

DLK-278, "CONSOLE : Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

BCM

Inside key antenna (console)

Continuity 

Connector

Terminal

Connector

Terminal

B16

63

B77

1

Yes

62

2

BCM

Ground

Continuity 

Connector

Terminal

B16

63

No

62

(+)

(–)

Condition

Signal

(Reference value)

BCM

Connector

Terminal

B16

62, 63

Ground

When Intelligent Key is in the an-
tenna detection area.

When Intelligent Key is not in the 
antenna detection area.

JMKIA3839GB

JMKIA5951GB

2015 Rogue NAM

DLK-148

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

AUTOMATIC BACK DOOR CONTROL UNIT
AUTOMATIC BACK DOOR CONTROL UNIT : Diagnosis Procedure

INFOID:0000000011278857

Regarding Wiring Diagram information, refer to 

DLK-73, "Wiring Diagram"

.

1.

CHECK FUSIBLE LINK

Check that the following fusible link is not open.

Is the fusible link open?

YES

>> Replace the open fusible link after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect automatic back door control module connector.

3. Check voltage between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK GROUND CIRCUIT

Check continuity between automatic back door control module harness connector and ground.

Does continuity exist?

YES

>> Inspection End.

NO

>> Repair or replace harness.

BCM
BCM : Diagnosis Procedure

INFOID:0000000011377366

Regarding Wiring Diagram information, refer to 

BCS-50, "Wiring Diagram"

.

1.

 CHECK FUSE

Check that the following fuse is not blown.

Fusible link No.

Signal name

K (30A)

Battery power supply

(+)

(

−)

Voltage

(Approx.)

Automatic back door control module

Connector

Terminal

B56

25

Ground

Battery voltage

Automatic back door control module

Ground

Continuity

Connector

Terminal

B56

32

Yes

B55

4

B55

16

2015 Rogue NAM

POWER SUPPLY AND GROUND CIRCUIT

DLK-149

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the fuse blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

 CHECK POWER SUPPLY CIRCUIT

1. Disconnect BCM connector M20.

2. Check voltage between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

 CHECK GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

Terminal No.

Signal name

Fuse No.

161

BCM power supply

7 (10A)

BCM

Ground

Voltage

(Approx.)

Connector

Terminal

M20

161

—

Battery voltage

BCM

Ground

Continuity

Connector

Terminal

M20

170

—

Yes

171

2015 Rogue NAM