Nissan Rogue. Manual - part 1230

WCS

WARNING CHIME SYSTEM SYMPTOMS

WCS-49

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SYMPTOM DIAGNOSIS

WARNING CHIME SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000011276489

CAUTION:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-

sis if any DTC is detected.

Symptom

Possible cause

Inspection item

The light reminder warning does not sound.

• Harness between BCM and front door switch LH.
• Front door switch LH
• BCM
• Combination meter

Refer to 

WCS-

52

.

The parking brake release warning contin-
ues sounding or does not sound.

• Harness between combination meter and parking brake switch.
• Parking brake switch
• BCM
• Combination meter

Refer to 

WCS-

50

.

The seat belt warning continues sounding 
or does not sound.

• Harness between combination meter and seat belt buckle switch LH.
• Seat belt buckle switch LH
• BCM
• Combination meter

Refer to 

WCS-

51

.

Warning chime does not sound at all.

• BCM
• Combination meter

Refer to 

WCS-

42

.

WCS-50

< SYMPTOM DIAGNOSIS >

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR 

DOES NOT SOUND

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND

Description

INFOID:0000000011276490

• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is

released.

• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking

brake applied.

Diagnosis Procedure

INFOID:0000000011276491

1.

 CHECK PARKING BRAKE WARNING LAMP

1. Start the engine.

2. Check the operation of the brake warning lamp by operating the parking brake.

Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> GO TO 2.

2.

 CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT

Check the parking brake switch signal circuit. Refer to 

WCS-45, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

 CHECK PARKING BRAKE SWITCH UNIT

Check the parking brake switch. Refer to 

WCS-46, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Replace the parking brake switch. Refer to 

PB-7, "Exploded View"

. 

Condition

Warning lamp status

Parking brake applied

ON

Parking brake released

OFF

WCS

THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES 

NOT SOUND

WCS-51

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND

Description

INFOID:0000000011276492

• Seat belt warning does not sound even though driver seat belt is not fastened.

• Seat belt warning sounds even though driver seat belt is fastened.

Diagnosis Procedure

INFOID:0000000011276493

1.

CHECK WARNING CHIME OPERATION

1. Select “BUZZER” of “BCM” using CONSULT.

2. Perform “SEAT BELT WARN TEST” in “Active Test”.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

2.

CHECK COMBINATION METER INPUT SIGNAL

Check the combination meter input signal. Refer to 

WCS-43, "Component Function Check"

. 

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

NO

>> GO TO 3.

3.

CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT

Check the seat belt buckle switch LH circuit. Refer to 

WCS-43, "Diagnosis Procedure"

. 

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connector.

4.

CHECK SEAT BELT BUCKLE SWITCH LH

Check the seat belt buckle switch LH. Refer to 

WCS-44, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Replace the seat belt buckle switch LH. Refer to 

SB-11, "FRONT SEAT BELT BUCKLE : Removal

and Installation"

.

Component

CONSULT

Condition

Buzzer

SEAT BELT WARN TEST

ON

OFF

WCS-52

< SYMPTOM DIAGNOSIS >

THE LIGHT REMINDER WARNING DOES NOT SOUND

THE LIGHT REMINDER WARNING DOES NOT SOUND

Description

INFOID:0000000011276494

Light reminder warning does not sound even though headlamp is illuminated.

Diagnosis Procedure

INFOID:0000000011276495

1.

CHECK COMBINATION METER INPUT SIGNAL

Select the “Data Monitor” of “METER/M&A” using CONSULT and check the “BUZZER” monitor value.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK FRONT DOOR SWITCH LH SIGNAL CIRCUIT

Check the front door switch LH signal circuit. Refer to 

DLK-156, "Diagnosis Procedure"

 (with Intelligent Key

system) or 

DLK-330, "Diagnosis Procedure"

 (without Intelligent Key system).

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK FRONT DOOR SWITCH LH

Check the front door switch LH. Refer to 

DLK-157, "Component Inspection"

 (with Intelligent Key system) or

DLK-331, "Component Inspection"

 (without Intelligent Key system).

Is the inspection result normal?

YES

>> Replace the BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or

BCS-135, "Removal and Installation"

 (without Intelligent Key system).

NO

>> Replace the front door switch LH. Refer to 

DLK-276, "Removal and Installation"

 (with Intelligent

Key system) or 

DLK-396, "Removal and Installation"

 (without Intelligent Key system).

Monitor item

Condition

Status

BUZZER

Under the condition of buzzer input

On

Except above

Off