Nissan Rogue. Manual - part 1031

SB-10

< REMOVAL AND INSTALLATION >

FRONT SEAT BELT

CAUTION:

• For removing/installing the lap belt pre-tensioner harness

connector, insert a thin screwdriver wrapped in tape into

the notch, then lift the lock and remove the harness con-

nector as shown.

• Install the harness connector with the lock raised, and

push the lock into the harness connector as shown.

• After installing the harness connector, check that the lock

is pushed in securely.

7. Remove seat belt retractor bolt and lap belt pre-tensioner bolt and remove seat belt retractor.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Tighten the D-ring Anchor bolt and seat belt retractor bolts to specification. Refer to 

SB-8, "Exploded

View"

.

• Tighten the lap belt pre-tensioner bolts to specification. Refer to 

SB-8, "Exploded View"

.

• Make sure that the seat belt height adjuster is locked in the lowest position and is aligned with the

center pillar upper finisher opening during installation.

• Make sure both the D-ring anchor and seat belt height adjuster operate freely.

• Always perform an inspection after repair to make sure the system is functioning within specifica-

tions. Refer to 

SB-5, "Inspection"

.

SEAT BELT HEIGHT ADJUSTER
SEAT BELT HEIGHT ADJUSTER : Removal and Installation

INFOID:0000000011279683

REMOVAL

1. Remove center pillar upper finisher. Refer to 

INT-21, "CENTER PILLAR UPPER FINISHER : Removal

and Installation"

.

2. Remove the seat belt height adjuster bolts (A) and seat belt height adjuster (1).

: Front

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Make sure that the seat belt height adjuster is locked in the lowest position and is aligned with the

center pillar upper finisher opening during installation.

• Tighten the D-ring anchor bolt and seat belt height adjuster bolts to specification. Refer to 

SB-8,

"Exploded View"

. 

• Make sure both the D-ring anchor and seat belt height adjuster operate freely.

• Always perform an inspection after repair to make sure the system is functioning within specifica-

tions. Refer to 

SB-5, "Inspection"

. 

FRONT SEAT BELT BUCKLE

PHIA0953J

ALHIA0371ZZ

FRONT SEAT BELT

SB-11

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SB

N

O

P

FRONT SEAT BELT BUCKLE : Removal and Installation

INFOID:0000000011279684

REMOVAL

1. Remove front seat. Refer to 

SE-32, "DRIVER SIDE : Removal and Installation"

 (Driver side) or 

SE-35,

"PASSENGER SIDE : Removal and Installation"

 (Passenger side).

2. Disconnect seat belt buckle harness connector.
3. Remove seat belt buckle anchor bolt and seat belt buckle.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Tighten the seat belt buckle anchor bolt to specification. Refer to 

SB-8, "Exploded View"

.

• Always perform an inspection after repair to make sure the system is functioning within specifica-

tions. Refer to 

SB-5, "Inspection"

.

SB-12

< REMOVAL AND INSTALLATION >

SECOND ROW SEAT BELT

SECOND ROW SEAT BELT

Exploded View

INFOID:0000000011279685

SEAT BELT RETRACTOR
SEAT BELT RETRACTOR : Removal and Installation

INFOID:0000000011279686

SEAT BELT RETRACTOR - (LH/RH)

Removal

1.

Seat belt retractor (center)

2.

Seat belt D-ring bracket (LH/
RH)

3.

Seat belt hook (LH/RH)

4.

Seat belt retractor (RH)

5.

Seat belt D-ring bolt cover 
(LH/RH)

6.

Seat belt buckle (RH)

7.

Seat belt buckle (center)

8.

Seat belt buckle (LH)

9.

Seat belt retractor (LH)

10. Seat belt center retractor outer 

finisher

AWHIA0729ZZ

SECOND ROW SEAT BELT

SB-13

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SB

N

O

P

1. Remove luggage side upper finisher. Refer to 

INT-36, "LUGGAGE SIDE UPPER FINISHER : Removal

and Installation"

.

2. Remove second row seat. Refer to 

SE-39, "Removal and Installation"

.

3. Remove lower anchor bolt (A).

: Front

4. Remove seat belt retractor bolt (A) and remove seat belt retrac-

tor (1).

: Front

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Tighten the D-ring anchor bolt, seat belt retractor bolt, and lower anchor bolt to specification. Refer

to 

SB-12, "Exploded View"

.

• Make sure the D-ring anchor operates freely.

• Always perform an inspection after repair to make sure the system is functioning within specifica-

tions. Refer to 

SB-5, "Inspection"

. 

SEAT BELT RETRACTOR - (CENTER)

Removal

1. Remove seatback pad and seatback trim (LH). Refer to 

SE-67, "LH SEAT : Seatback"

.

2. Remove seat belt retractor lower anchor nut (A), then route seat

belt retactor (1) through seat cushion (LH).

ALHIA0372ZZ

ALHIA0373ZZ

ALHIA0374ZZ