Almera Tino V10 (2003 year). Manual

SMT066A

Install 3rd & 4th shift fork and bracket, then install 3rd & 4th
fork rod, stopper ring and retaining pin.
When installing stopper rings, use snap ring remover and
installer.

SMT067A

Install interlock balls.

SMT666C

Install 5th shift fork, then install fork rod, stopper ring and
retaining pin.
When installing stopper rings, use snap ring remover and
installer.

SMT018B

10. Install 5th & reverse check plug, spring and ball.

Apply sealant to bolt threads. Refer to “Shift Control
Components”, MT-65.

SMT201B

11. Install reverse lock spring on 5th & reverse bracket.

Pay attention to its direction.

ASSEMBLY

RS5F50A

MT-86

SMT667C

12. Install check ball and reverse lever spring on reverse lever

assembly.

Apply multi-purpose grease to check ball.

Pay attention to direction of reverse lever spring.

SMT668C

13. Install reverse lever assembly on clutch housing.

SMT669C

14. Install reverse arm shaft and retaining pin.

SMT670C

15. Hook reverse lock spring and reverse lever spring on reverse

lever assembly.

SMT671C

16. Mesh 4th gear, then install reverse idler gear and shaft.

Pay attention to direction of tapped hole.

IDX

ASSEMBLY

RS5F50A

MT-87

SMT070A

17. Place magnet on clutch housing.

SMT446C

18. If bearing preload of mainshaft was adjusted, install selected

shim(s) into transmission case.

To aid in installation of transmission case, place shift
selector in the 1st and 2nd shift bracket or between 1st
and 2nd bracket and 3rd and 4th bracket.

19. Apply sealant to mating surface of transmission case and

install it. Refer to “Case Components”, MT-63.

20. Install PNP switch.

SMT626D

21. Apply sealant to threads of check plugs. Install balls, springs

and plugs. Refer to “Shift Control Components”, MT-65.

22. After assembly, check that you can shift into each gear

smoothly.

SAT478EA

23. Measure total turning torque.

Total turning torque (New bearing):

8.8 - 21.6 N·m (90 - 220 kg-cm, 78 - 191 in-lb)

When old bearing is used again, preload will be slightly
less than the above. Make sure torque is close to the
specified range.

ASSEMBLY

RS5F50A

MT-88

General Specifications

NLMT0076

TRANSAXLE

NLMT0076S01

Applied model

QG18DE

Model code number

8E009

8E069

Transaxle model

RS5F70A

Number of speeds

Synchromesh type

Warner

Shift pattern

Gear ratio

1st

3.333

2nd

1.955

3rd

1.286

4th

0.926

5th

0.733

Reverse

3.214

Number of teeth

Input gear

1st

2nd

3rd

4th

5th

Rev.

Main gear

1st

2nd

3rd

4th

5th

Rev.

Reverse idler gear

Oil capacity

(Imp pt)

3.0 (5-1/4)

Oil level (Reference data)

mm (in)

56.5 - 61.0 (2.224 - 2.402)

Remarks

1st & 2nd double baulk ring type synchronizer

Reverse sub-gear

FINAL GEAR

NLMT0076S02

Engine

QG18DE

Transaxle model

RS5F70A

Final gear ratio

4.437

Number of teeth

Final gear/Pinion

71/16

Side gear/Pinion mate gear

14/10

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

General Specifications

MT-89

Gear End Play

NLMT0077

Unit: mm (in)

Gear

End play

1st main gear

0.18 - 0.31 (0.0071 - 0.0122)

2nd main gear

5th main gear

Reverse main gear

3rd input gear

4th input gear

0.17 - 0.44 (0.0067 - 0.0173)

Clearance Coupling Sleeve

NLMT0094

1ST, 2ND, 3RD, 4TH, 5TH & REVERSE COUPLING SLEEVE

NLMT0094S01

Coupling sleeve

Length “L”

1st & 2nd

0 - 0.68 mm (0 - 0.0268 in)

3rd & 4th

0 - 0.95 mm (0 - 0.0374 in)

5th & Reverse

0 - 0.89 mm (0 - 0.0350 in)

Clearance Between Baulk Ring and Gear

NLMT0078

3RD, 4TH, 5TH, REVERSE BAULK RING

NLMT0078S01

Unit: mm (in)

Standard

Wear limit

3rd

0.90 - 1.45 (0.0354 - 0.0571)

0.7 (0.028)

4th

5th

Reverse

0.9 - 1.35 (0.0354 - 0.0531)

1ST AND 2ND DOUBLE BAULK RING

NLMT0078S02

Unit: mm (in)

SMT906D

Dimension

Standard

Wear limit

0.6 - 0.8 (0.024 - 0.031)

0.2 (0.008)

0.6 - 1.1 (0.024 - 0.043)

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

Gear End Play

MT-90

Available Snap Rings

NLMT0079

SNAP RING

NLMT0079S01

End play

0.05 - 0.25 mm (0.0020 - 0.0098 in)

Thickness

mm (in)

Part number*

1.45 (0.0571)

32204-6J000

1.55 (0.0610)

32204-6J001

1.65 (0.0650)

32204-6J002

1.75 (0.0689)

32204-6J003

1.85 (0.0728)

32204-6J004

*: Always check with the parts department for the latest information.

Available C-rings

NLMT0080

4TH INPUT GEAR C-RING

NLMT0080S01

End play

0 - 0.06 mm (0 - 0.0024 in)

Thickness

mm (in)

Part number*

3.00 (0.1181)

32205-6J000

3.03 (0.1193)

32205-6J001

3.06 (0.1205)

32205-6J002

3.09 (0.1217)

32205-6J003

3.12 (0.1228)

32205-6J004

*: Always check with the parts department for the latest information.

5TH INPUT GEAR REAR C-RING

NLMT0080S02

End play

0 - 0.06 mm (0 - 0.0024 in)

Thickness

mm (in)

Part number*

2.59 (0.1020)

32205-6J005

2.62 (0.1031)

32205-6J006

2.65 (0.1043)

32205-6J007

2.68 (0.1055)

32205-6J008

2.71 (0.1067)

32205-6J009

2.74 (0.1079)

32205-6J010

*: Always check with the parts department for the latest information.

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

Available Snap Rings

MT-91

MAINSHAFT C-RING

NLMT0080S03

End play

0 - 0.06 mm (0 - 0.0024 in)

Thickness

mm (in)

Part number*

3.48 (0.1370)

32348-6J000

3.51 (0.1382)

32348-6J001

3.54 (0.1394)

32348-6J002

3.57 (0.1406)

32348-6J003

3.60 (0.1417)

32348-6J004

3.63 (0.1429)

32348-6J005

3.66 (0.1441)

32348-6J006

3.69 (0.1453)

32348-6J007

3.72 (0.1465)

32348-6J008

3.75 (0.1476)

32348-6J009

3.78 (0.1488)

32348-6J010

3.81 (0.1500)

32348-6J011

3.84 (0.1512)

32348-6J012

3.87 (0.1524)

32348-6J013

3.90 (0.1535)

32348-6J014

3.93 (0.1547)

32348-6J015

3.96 (0.1559)

32348-6J016

*: Always check with the parts department for the latest information.

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

Available C-rings (Cont’d)

MT-92

Available Adjusting Shims

NLMT0081

INPUT SHAFT REAR BEARING ADJUSTING SHIM

NLMT0081S01

End play

0 - 0.06 mm (0 - 0.0024 in)

Thickness

mm (in)

Part number*

0.74 (0.0291)

32225-6J003

0.78 (0.0307)

32225-6J004

0.82 (0.0323)

32225-6J005

0.86 (0.0339)

32225-6J006

0.90 (0.0354)

32225-6J007

0.94 (0.0370)

32225-6J008

0.98 (0.0386)

32225-6J009

1.02 (0.0402)

32225-6J010

1.06 (0.0417)

32225-6J011

1.10 (0.0433)

32225-6J012

1.14 (0.0449)

32225-6J013

1.18 (0.0465)

32225-6J014

1.22 (0.0480)

32225-6J015

1.26 (0.0496)

32225-6J016

1.30 (0.0512)

32225-6J017

1.34 (0.0528)

32225-6J018

1.38 (0.0543)

32225-6J019

1.42 (0.0559)

32225-6J020

1.46 (0.0575)

32225-6J021

1.50 (0.0591)

32225-6J022

1.54 (0.0606)

32225-6J023

1.58 (0.0622)

32225-6J024

1.62 (0.0638)

32225-6J060

1.66 (0.0654)

32225-6J061

*: Always check with the parts department for the latest information.

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

Available Adjusting Shims

MT-93

MAINSHAFT ADJUSTING SHIM

NLMT0081S02

SMT907D

Standard length “L”

151.35 - 151.45 mm (5.9586 - 5.9626 in)

Thickness

mm (in)

Part number*

0.48 (0.0189)

32238-6J000

0.56 (0.0220)

32238-6J001

0.64 (0.0252)

32238-6J002

0.72 (0.0283)

32238-6J003

0.80 (0.0315)

32238-6J004

0.88 (0.0346)

32238-6J005

*: Always check with the parts department for the latest information.

MAINSHAFT REAR BEARING ADJUSTING SHIM

NLMT0081S03

End play

0 - 0.06 mm (0 - 0.0024 in)

Thickness

mm (in)

Part number*

2.99 (0.1177)

32238-6J010

3.03 (0.1193)

32238-6J011

3.07 (0.1209)

32238-6J012

3.11 (0.1224)

32238-6J013

3.15 (0.1240)

32238-6J014

3.19 (0.1256)

32238-6J015

3.23 (0.1272)

32238-6J016

3.27 (0.1287)

32238-6J017

3.31 (0.1303)

32238-6J018

3.35 (0.1319)

32238-6J019

3.39 (0.1335)

32238-6J020

3.43 (0.1350)

32238-6J021

3.47 (0.1366)

32238-6J022

3.51 (0.1382)

32238-6J023

*: Always check with the parts department for the latest information.

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

Available Adjusting Shims (Cont’d)

MT-94

Available Thrust Washer

NLMT0082

MAINSHAFT THRUST WASHER

NLMT0082S01

SMT843D

Standard length “M”

244.20 - 244.30 mm (9.6142 - 9.6181 in)

Thickness

mm (in)

Part number*

6.04 (0.2378)

32246-6J000

6.12 (0.2409)

32246-6J001

6.20 (0.2441)

32246-6J002

6.28 (0.2472)

32246-6J003

6.36 (0.2504)

32246-6J004

*: Always check with the parts department for the latest information.

Available Washers

NLMT0083

DIFFERENTIAL SIDE GEAR THRUST WASHER

NLMT0083S01

Clearance between side gear and differential case

0.1 - 0.2 mm (0.004 - 0.008 in)

Thickness mm (in)

Part number*

0.75 - 0.80 (0.0295 - 0.0315)

38424-D2111

0.80 - 0.85 (0.0315 - 0.0335)

38424-D2112

0.85 - 0.90 (0.0335 - 0.0354)

38424-D2113

0.90 - 0.95 (0.0354 - 0.0374)

38424-D2114

0.95 - 1.00 (0.0374 - 0.0394)

38424-D2115

*: Always check with the parts department for the latest information.

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

Available Thrust Washer

MT-95

Available Shims — Differential Side Bearing
Preload and Adjusting Shim

=NLMT0084

BEARING PRELOAD

NLMT0084S01

Unit: mm (in)

Differential side bearing preload: T*

0.15 - 0.21 (0.0059 - 0.0083)

*: Install shims which are “deflection of differential case” + “T” in thickness.

DIFFERENTIAL SIDE BEARING ADJUSTING SHIMS

NLMT0084S02

Thickness mm (in)

Part number*

0.44 (0.0173)

38454-M8000

0.48 (0.0189)

38454-M8001

0.52 (0.0205)

38454-M8002

0.56 (0.0220)

38454-M8003

0.60 (0.0236)

38454-M8004

0.64 (0.0252)

38454-M8005

0.68 (0.0268)

38454-M8006

0.72 (0.0283)

38454-M8007

0.76 (0.0299)

38454-M8008

0.80 (0.0315)

38454-M8009

0.84 (0.0331)

38454-M8010

0.88 (0.0346)

38454-M8011

*: Always check with the parts department for the latest information.

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F70A

Available Shims — Differential Side Bearing Preload and Adjusting Shim

MT-96

General Specifications

NLMT0024

TRANSAXLE

NLMT0024S01

Applied model

YD22DDTi

Model code number

4U107

Transaxle model

RS5F50A

Number of speeds

Synchromesh type

Warner

Shift pattern

Gear ratio

1st

3.400

2nd

1.955

3rd

1.206

4th

0.829

5th

0.641

Reverse

3.428

Number of teeth

Input gear

1st

2nd

3rd

4th

5th

Rev.

Main gear

1st

2nd

3rd

4th

5th

Rev.

Reverse idler gear

Oil capacity

(Imp pt)

4.5 - 4.8 (7-7/8 - 8-1/2)

Remarks

1st & 2nd double baulk ring type synchronizer

FINAL GEAR

NLMT0024S02

Engine

YD22DDT

Transaxle model

RS5F50A

Final gear ratio

3.823

Number of teeth

Final gear/Pinion

65/17

Side gear/Pinion

14/10

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F50A

General Specifications

MT-97

Gear End Play

NLMT0025

Unit: mm (in)

Gear

End play

1st main gear
2nd main gear
3rd input gear
4th input gear
5th input gear

0.23 - 0.43 (0.0091 - 0.0169)
0.23 - 0.58 (0.0091 - 0.0228)
0.23 - 0.43 (0.0091 - 0.0169)
0.25 - 0.55 (0.0098 - 0.0217)
0.23 - 0.48 (0.0091 - 0.0189)

Clearance Between Baulk Ring and Gear

NLMT0026

3RD, 4TH & 5TH BAULK RING

NLMT0026S01

Unit: mm (in)

Gear

Standard

Wear limit

3rd, 4th & 5th

1.0 - 1.35 (0.0394 - 0.0531)

0.7 (0.028)

1ST AND 2ND DOUBLE BAULK RING

NLMT0026S02

Unit: mm (in)

SMT806B

Dimension

Standard

Wear limit

0.6 - 0.8 (0.024 - 0.031)

0.2 (0.008)

0.6 - 1.1 (0.024 - 0.043)

REVERSE BAULK RING

NLMT0026S03

SMT581B

Dimension

Wear limit

1.2 mm (0.047 in)

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F50A

Gear End Play

MT-98

Available Snap Rings

=NLMT0027

1ST & 2ND SYNCHRONIZER HUB (AT MAINSHAFT)

NLMT0027S01

Allowable clearance

0 - 0.1 mm (0 - 0.004 in)

Thickness mm (in)

Part number*

1.95 (0.0768)
2.00 (0.0787)
2.05 (0.0807)
2.10 (0.0827)

32269-03E03
32269-03E00
32269-03E01
32269-03E02

*: Always check with the Parts Department for the latest parts information.

3RD & 4TH SYNCHRONIZER HUB (AT INPUT SHAFT)

NLMT0027S02

Allowable clearance

0 - 0.1 mm (0 - 0.004 in)

Thickness mm (in)

Part number*

1.95 (0.0768)
2.00 (0.0787)
2.05 (0.0807)
2.10 (0.0827)

32269-03E03
32269-03E00
32269-03E01
32269-03E02

*: Always check with the Parts Department for the latest parts information.

5TH MAIN GEAR (AT MAINSHAFT)

NLMT0027S03

Allowable clearance

0 - 0.15 mm (0 - 0.0059 in)

Thickness mm (in)

Part number*

1.95 (0.0768)
2.05 (0.0807)
2.15 (0.0846)
2.25 (0.0886)

32348-05E00
32348-05E01
32348-05E02
32348-05E03

*: Always check with the Parts Department for the latest parts information.

Available Thrust Washer

NLMT0028

4TH INPUT GEAR (AT INPUT SHAFT)

NLMT0028S01

Allowable clearance

0 - 0.06 mm (0 - 0.0024 in)

Thickness mm (in)

Part number*

4.500 (0.1772)
4.525 (0.1781)
4.550 (0.1791)
4.575 (0.1801)

32278-03E01
32278-03E02
32278-03E03
32278-03E04

*: Always check with the Parts Department for the latest parts information.

DIFFERENTIAL SIDE GEAR THRUST WASHER

NLMT0028S02

Allowable clearance between side gear and differential case with washer

0.1 - 0.2 mm (0.004 - 0.008 in)

Thickness mm (in)

Part number*

0.75 - 0.80 (0.0295 - 0.0315)
0.80 - 0.85 (0.0315 - 0.0335)
0.85 - 0.90 (0.0335 - 0.0354)
0.90 - 0.95 (0.0354 - 0.0374)

38424-E3020
38424-E3021
38424-E3022
38424-E3023

*: Always check with the Parts Department for the latest parts information.

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F50A

Available Snap Rings

MT-99

Available Shims

=NLMT0029

— INPUT SHAFT END PLAY AND MAINSHAFT AND DIFFERENTIAL SIDE BEARING PRELOAD AND
ADJUSTING SHIM

BEARING PRELOAD AND END PLAY

NLMT0029S01

Unit: mm (in)

Mainshaft bearing preload

0.06 - 0.11 (0.0024 - 0.0043)

Input shaft end play

0 - 0.05 (0 - 0.0020)

Differential side bearing preload

0.40 - 0.45 (0.0157 - 0.0177)

TOTAL TURNING TORQUE (NEW BEARING)

NLMT0029S02

Unit: N·m (kg-cm, in-lb)

Total turning torque (new bearing)

8.8 - 21.6 (90 - 220, 78 - 191)

MAINSHAFT BEARING ADJUSTING SHIM

NLMT0029S03

Thickness mm (in)

Part number*

0.40 (0.0157)
0.44 (0.0173)
0.48 (0.0189)
0.52 (0.0205)
0.56 (0.0220)
0.60 (0.0236)
0.64 (0.0252)
0.68 (0.0268)
0.72 (0.0283)
0.76 (0.0299)
0.80 (0.0315)
1.20 (0.0472)

32139-03E11

32139-03E00
32139-03E01
32139-03E12
32139-03E02
32139-03E03
32139-03E04
32139-03E05
32139-03E06
32139-03E07
32139-03E08
32139-03E13

*: Always check with the Parts Department for the latest parts information.

TABLE FOR SELECTING MAINSHAFT BEARING ADJUSTING SHIM(S)

NLMT0029S04

Unit: mm (in)

Dimension “C”

Suitable shim(s)

0.30 - 0.34 (0.0118 - 0.0134)

0.34 - 0.38 (0.0134 - 0.0150)
0.38 - 0.42 (0.0150 - 0.0165)
0.42 - 0.46 (0.0165 - 0.0181)
0.46 - 0.50 (0.0181 - 0.0197)
0.50 - 0.54 (0.0197 - 0.0213)
0.54 - 0.58 (0.0213 - 0.0228)
0.58 - 0.62 (0.0228 - 0.0244)
0.62 - 0.66 (0.0244 - 0.0260)
0.66 - 0.70 (0.0260 - 0.0276)
0.70 - 0.74 (0.0276 - 0.0291)
0.74 - 0.78 (0.0291 - 0.0307)
0.78 - 0.82 (0.0307 - 0.0323)
0.82 - 0.86 (0.0323 - 0.0339)
0.86 - 0.90 (0.0339 - 0.0354)
0.90 - 0.94 (0.0354 - 0.0370)
0.94 - 0.98 (0.0370 - 0.0386)
0.98 - 1.02 (0.0386 - 0.0402)
1.02 - 1.06 (0.0402 - 0.0417)
1.06 - 1.10 (0.0417 - 0.0433)
1.10 - 1.14 (0.0433 - 0.0449)
1.14 - 1.18 (0.0449 - 0.0465)
1.18 - 1.22 (0.0465 - 0.0480)
1.22 - 1.26 (0.0480 - 0.0496)
1.26 - 1.30 (0.0496 - 0.0512)
1.30 - 1.34 (0.0512 - 0.0528)
1.34 - 1.38 (0.0528 - 0.0543)
1.38 - 1.42 (0.0543 - 0.0559)
1.42 - 1.46 (0.0559 - 0.0575)
1.46 - 1.50 (0.0575 - 0.0591)

0.40 (0.0157)
0.44 (0.0173)
0.48 (0.0189)
0.52 (0.0205)
0.56 (0.0220)
0.60 (0.0236)
0.64 (0.0252)
0.68 (0.0268)
0.72 (0.0283)
0.76 (0.0299)
0.80 (0.0315)

0.40 + 0.44 (0.0157 + 0.0173)
0.44 + 0.44 (0.0173 + 0.0173)
0.44 + 0.48 (0.0173 + 0.0189)
0.48 + 0.48 (0.0189 + 0.0189)
0.48 + 0.52 (0.0189 + 0.0205)
0.52 + 0.52 (0.0205 + 0.0205)
0.52 + 0.56 (0.0205 + 0.0220)
0.56 + 0.56 (0.0220 + 0.0220)
0.56 + 0.60 (0.0220 + 0.0236)
0.60 + 0.60 (0.0236 + 0.0236)
0.60 + 0.64 (0.0236 + 0.0252)
0.64 + 0.64 (0.0252 + 0.0252)
0.64 + 0.68 (0.0252 + 0.0268)
0.68 + 0.68 (0.0268 + 0.0268)
0.68 + 0.72 (0.0268 + 0.0283)
0.72 + 0.72 (0.0283 + 0.0283)
0.72 + 0.76 (0.0283 + 0.0299)
0.76 + 0.76 (0.0299 + 0.0299)
0.76 + 0.80 (0.0299 + 0.0315)

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F50A

Available Shims

MT-100

INPUT SHAFT BEARING ADJUSTING SHIM

NLMT0029S05

Thickness mm (in)

Part number*

0.40 (0.0157)
0.44 (0.0173)
0.48 (0.0189)
0.52 (0.0205)
0.56 (0.0220)
0.60 (0.0236)
0.64 (0.0252)
0.68 (0.0268)
0.72 (0.0283)
0.76 (0.0299)
0.80 (0.0315)
1.20 (0.0472)

32225-08E00
32225-08E01
32225-08E02
32225-08E03
32225-08E04
32225-08E05
32225-08E06
32225-08E07
32225-08E08
32225-08E09
32225-08E10

32225-08E11

*: Always check with the Parts Department for the latest parts information.

TABLE FOR SELECTING INPUT SHAFT BEARING ADJUSTING SHIM(S)

NLMT0029S06

Unit: mm (in)

Dial indicator indication

Suitable shim(s)

0.65 - 0.69 (0.0256 - 0.0272)
0.69 - 0.73 (0.0272 - 0.0287)
0.73 - 0.77 (0.0287 - 0.0303)
0.77 - 0.81 (0.0303 - 0.0319)
0.81 - 0.85 (0.0319 - 0.0335)
0.85 - 0.89 (0.0335 - 0.0350)
0.89 - 0.93 (0.0350 - 0.0366)
0.93 - 0.97 (0.0366 - 0.0382)
0.97 - 1.01 (0.0382 - 0.0398)
1.01 - 1.05 (0.0398 - 0.0413)
1.05 - 1.09 (0.0413 - 0.0429)
1.09 - 1.13 (0.0429 - 0.0445)
1.13 - 1.17 (0.0445 - 0.0461)
1.17 - 1.21 (0.0461 - 0.0476)
1.21 - 1.25 (0.0476 - 0.0492)
1.25 - 1.29 (0.0492 - 0.0508)
1.29 - 1.33 (0.0508 - 0.0524)
1.33 - 1.37 (0.0524 - 0.0539)
1.37 - 1.41 (0.0539 - 0.0555)
1.41 - 1.45 (0.0555 - 0.0571)
1.45 - 1.49 (0.0571 - 0.0587)
1.49 - 1.53 (0.0587 - 0.0602)
1.53 - 1.57 (0.0602 - 0.0618)
1.57 - 1.61 (0.0618 - 0.0634)
1.61 - 1.65 (0.0634 - 0.0650)
1.65 - 1.69 (0.0650 - 0.0665)

0.64 (0.0252)
0.68 (0.0268)
0.72 (0.0283)
0.76 (0.0299)
0.80 (0.0315)

DIFFERENTIAL SIDE BEARING ADJUSTING SHIM

NLMT0029S07

Thickness mm (in)

Part number*

0.40 (0.0157)
0.44 (0.0173)
0.48 (0.0189)
0.52 (0.0205)
0.56 (0.0220)
0.60 (0.0236)
0.64 (0.0252)
0.68 (0.0268)
0.72 (0.0283)
0.76 (0.0299)
0.80 (0.0315)
0.84 (0.0331)
0.88 (0.0346)
1.20 (0.0472)

38453-96E00
38453-96E01
38453-96E02
38453-96E03
38453-96E04
38453-96E05
38453-96E06
38453-96E07
38453-96E08
38453-96E09
38453-96E10

38453-96E11

38453-96E12
38453-96E13

*: Always check with the Parts Department for the latest parts information.

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

RS5F50A

Available Shims (Cont’d)

MT-101

Almera Tino V10 (2003 year). Manual - part 231