Nissan GT-R. Manual - part 130

WHEEL ALIGNMENT

FSU-9

< PERIODIC MAINTENANCE >

C

D

F

G

H

I

J

K

L

M

A

B

FSU

N

O

P

• Refer to figure for selection of shim.

• Assemble the shims and the rubber bushings while facing the rubber bushings toward the upper

link side. 

NOTE:
The shims and rubber bushings are fitted on a new vehicle [shim: 3 mm (0.12 in)] are a single unit. However
the shims for adjustment and rubber bushings are separated parts. When shim: 6 mm (0.24in) is selected, fix
it on one side only.

JPEIA0116GB

FSU-10

< REMOVAL AND INSTALLATION >

FRONT COIL SPRING AND SHOCK ABSORBER

REMOVAL AND INSTALLATION

FRONT COIL SPRING AND SHOCK ABSORBER

Exploded View

INFOID:0000000009163821

Disposal

INFOID:0000000009163825

1.

Set shock absorber horizontally with the piston rod fully extended.

2.

Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (

) from top

as shown in the figure to release gas gradually.

CAUTION:

• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-

pressed gas.

NOTE:
• Drill vertically in this direction (

).

• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.

3.

Position the drilled hole downward and drain oil by moving the piston rod several times.

CAUTION:

Dispose of drained oil according to the law and local regulations.

1.

Cap

2.

Piston rod lock nut

3.

Vehicle body

4.

Mounting seal

5.

Mount insulator

6.

Rubber seat

7.

Bound bumper

8.

Coil spring*

9.

Shock absorber

*: To replace, all of four coil springs must be replaced together as a set. (Vehicles with track pack-specific suspension)

Refer to 

GI-4, "Components"

 for the symbols in the figure.

JPEIA0117GB

A

: 20 – 30 mm (0.79 – 1.18 in)

NNEIA0021ZZ

TRANSVERSE LINK

FSU-11

< REMOVAL AND INSTALLATION >

C

D

F

G

H

I

J

K

L

M

A

B

FSU

N

O

P

TRANSVERSE LINK

Exploded View

INFOID:0000000009163826

*: The shims and rubber bushings are fitted on a new vehicle [shim: 3 mm (0.12 in)] are a single unit. However the shims for adjustment
and rubber bushings are separated parts. When shim: 6 mm (0.24in) is selected, fix it on one side only.

1.

Shim*

2.

Rubber bushing

3.

Upper link

4.

Transverse link

5.

Adjusting bolt

6.

Eccentric disk

Refer to 

GI-4, "Components"

 for the symbols in the figure.

JSEIA0366GB

FSU-12

< REMOVAL AND INSTALLATION >

UPPER LINK

UPPER LINK

Exploded View

INFOID:0000000009163829

*: The shims and rubber bushings are fitted on a new vehicle [shim: 3 mm (0.12 in)] are a single unit. However the shims for adjustment
and rubber bushings are separated parts. When shim: 6 mm (0.24in) is selected, fix it on one side only.

1.

Shim*

2.

Rubber bushing

3.

Upper link

4.

Transverse link

5.

Adjusting bolt

6.

Eccentric disk

Refer to 

GI-4, "Components"

 for the symbols in the figure.

JSEIA0366GB