Nissan Pathfinder. Manual - part 28

ADP-104

< DTC/CIRCUIT DIAGNOSIS >

TILT SWITCH

Is the inspection result normal?

YES

>> Replace automatic drive positioner unit. Refer to 

ADP-162, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

 CHECK TILT SWITCH

Refer to 

ADP-104, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace ADP steering switch (tilt switch). Refer to 

ADP-165, "Removal and Installation"

.

4.

 CHECK INTERMITTENT INCIDENT

Refer to 

GI-49, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000009176601

1.

 CHECK TILT SWITCH

1. Turn ignition switch OFF.

2. Disconnect ADP steering switch (tilt switch).

3. Check continuity between ADP steering switch terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace ADP steering switch (tilt switch). Refer to 

ADP-165, "Removal and Installation"

.

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M33

1

No

13

ADP steering 

switch (tilt switch)

Condition

Continuity

Terminal

3

5

Tilt switch (up)

Operate

Yes

Release

No

2

Tilt switch (down)

Operate

Yes

Release

No

TELESCOPIC SWITCH

ADP-105

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

TELESCOPIC SWITCH

Description

INFOID:0000000009176602

ADP steering switch (telescopic switch) is equipped to the steering column. The operation signal is input to the

automatic drive positioner control unit when the telescopic switch is operated.

Component Function Check

INFOID:0000000009176603

1.

 CHECK FUNCTION

1. Select “TELESCO SW-FR”, “TELESCO SW-RR” in “DATA MONITOR” mode with CONSULT. 

2. Check telescopic switch signal under the following conditions.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Perform diagnosis procedure. Refer to 

ADP-105, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009176604

Regarding Wiring Diagram information, refer to 

ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"

or 

ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"

.

1.

 CHECK TELESCOPIC SWITCH SIGNAL

1. Disconnect ADP steering switch (telescopic switch).

2. Check voltage between ADP steering switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

 CHECK TELESCOPIC SWITCH CIRCUIT

1. Disconnect automatic drive positioner control unit.

2. Check continuity between automatic drive positioner control unit harness connector and ADP steering

switch harness connector.

3. Check continuity between automatic drive positioner control unit harness connector and ground.

Monitor item

Condition

Status

TELESCO SW-FR

Telescopic switch (forward)

Operate

ON

Release

OFF

TELESCO SW-RR

Telescopic switch (backward)

Operate

ON

Release

OFF

(+)

(–)

Voltage (V)

(Approx.)

ADP steering switch (telescopic switch)

Connector

Terminals

M16

1

Ground

Battery voltage

6

Automatic drive positioner control 

unit

ADP steering switch (tele-

scopic switch)

Continuity

Connector

Terminal

Connector

Terminal

M33

7

M16

1

Yes

19

6

ADP-106

< DTC/CIRCUIT DIAGNOSIS >

TELESCOPIC SWITCH

Is the inspection result normal?

YES

>> Replace automatic drive positioner unit. Refer to 

ADP-162, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

 CHECK TELESCOPIC SWITCH

Refer to 

ADP-106, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace ADP steering switch (telescopic switch). Refer to 

ADP-165, "Removal and Installation"

.

4.

 CHECK INTERMITTENT INCIDENT

Refer to 

GI-49, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000009176605

1.

 CHECK TELESCOPIC SWITCH

1. Turn ignition switch OFF.

2. Disconnect ADP steering switch (telescopic switch).

3. Check continuity between ADP steering switch terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace ADP steering switch (telescopic switch). Refer to 

ADP-165, "Removal and Installation"

.

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M33

7

No

19

ADP steering switch (tele-

scopic switch)

Condition

Continuity

Terminal

3

1

Telescopic switch 
(forward)

Operate

Yes

Release

No

6

Telescopic switch 
(backward)

Operate

Yes

Release

No

SEAT MEMORY SWITCH

ADP-107

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

SEAT MEMORY SWITCH

Description

INFOID:0000000009176606

Seat memory switch is installed to the front door LH trim. The operation signal is input to the driver seat control

unit when the memory switch is operated.

Component Function Check

INFOID:0000000009176607

1.

 CHECK FUNCTION

1. Select “MEMORY SW 1”, “MEMORY SW 2”, “SET SW” in “DATA MONITOR” mode with CONSULT. 

2. Check seat memory switch signal under the following conditions.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Perform diagnosis procedure. Refer to 

ADP-107, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009176608

Regarding Wiring Diagram information, refer to 

ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"

or 

ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"

.

1.

 CHECK SEAT MEMORY SWITCH SIGNAL

1. Turn ignition switch OFF.

2. Disconnect seat memory switch.

3. Turn ignition switch ON.

4. Check voltage between seat memory switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

 CHECK MEMORY SWITCH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect driver seat control unit.

3. Check continuity between driver seat control unit harness connector and seat memory switch harness

connector.

Monitor item

Condition

Status

MEMORY SW 1

Memory switch 1

Push

ON

Release

OFF

MEMORY SW 2

Memory switch 2

Push

ON

Release

OFF

SET SW

Set switch 

Push

ON

Release

OFF

(+)

(–)

Voltage (V)

(Approx.)

Seat memory switch

Connector

Terminals

D60

2

Ground

5

10

16