Index Manuals Nissan Murano Z50 (2006 year) - Service and Repair Manual

Search copyright infringement

Content .. 77 78 79 80 ..

Nissan Murano Z50 (2006 year). Manual - part 79

POSITIVE CRANKCASE VENTILATION

EC-43

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

PCV VALVE VENTILATION HOSE

1.

Check hoses and hose connections for leaks.

2.

Disconnect all hoses and clean with compressed air. If any hose
cannot be freed of obstructions, replace.

S-ET277

EC-44

NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)

Revision: 2006 August

2006 Murano

NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)

PFP:25386

Description

NBS002Z0

●

If the security indicator lights up with the ignition switch in
the ON position or “NATS MALFUNCTION” is displayed on
“SELF-DIAG RESULTS” screen, perform self-diagnostic
results mode with CONSULT-II using NATS program card.
Refer to

BL-236, "NVIS (NISSAN VEHICLE IMMOBILIZER

SYSTEM-NATS)"

.

●

Confirm no self-diagnostic results of NVIS (NATS) is dis-
played before touching “ERASE” in “SELF-DIAG RESULTS”
mode with CONSULT-II.

●

When replacing ECM, initialization of NVIS (NATS) system
and registration of all NVIS (NATS) ignition key IDs must be
carried out with CONSULT-II using NATS program card.
Therefore, be sure to receive all keys from vehicle owner. Regarding the procedures of NVIS
(NATS) initialization and all NVIS (NATS) ignition key ID registration, refer to CONSULT-II operation
manual, IVIS/NVIS.

SEF543X

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-45

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

ON BOARD DIAGNOSTIC (OBD) SYSTEM

PFP:00028

Introduction

NBS002Z1

The ECM has an on board diagnostic system, which detects malfunctions related to engine sensors or actua-
tors. The ECM also records various emission-related diagnostic information including:

The above information can be checked using procedures listed in the table below.

×

: Applicable

—: Not applicable

*: When DTC and 1st trip DTC simultaneously appear on the display, they cannot be clearly distinguished from each other.

The malfunction indicator lamp (MIL) on the instrument panel lights up when the same malfunction is detected
in two consecutive trips (Two trip detection logic), or when the ECM enters fail-safe mode. (Refer to

Two Trip Detection Logic

NBS002Z2

When a malfunction is detected for the first time, 1st trip DTC and 1st trip Freeze Frame data are stored in the
ECM memory. The MIL will not light up at this stage. <1st trip>
If the same malfunction is detected again during the next drive, the DTC and Freeze Frame data are stored in
the ECM memory, and the MIL lights up. The MIL lights up at the same time when the DTC is stored. <2nd
trip> The “trip” in the “Two Trip Detection Logic” means a driving mode in which self-diagnosis is performed
during vehicle operation. Specific on board diagnostic items will cause the ECM to light up or blink the MIL,
and store DTC and Freeze Frame data, even in the 1st trip, as shown below.

×

: Applicable

—: Not applicable

When there is an open circuit on MIL circuit, the ECM cannot warn the driver by lighting up MIL when there is
malfunction on engine control system.
Therefore, when electrical controlled throttle and part of ECM related diagnoses are continuously detected as
NG for 5 trips, ECM warns the driver that engine control system malfunctions and MIL circuit is open by means
of operating fail-safe function.

Emission-related diagnostic information

Diagnostic service

Diagnostic Trouble Code (DTC)

Service $03 of SAE J1979

Freeze Frame data

Service $02 of SAE J1979

System Readiness Test (SRT) code

Service $01 of SAE J1979

1st Trip Diagnostic Trouble Code (1st Trip DTC)

Service $07 of SAE J1979

1st Trip Freeze Frame data

Test values and Test limits

Service $06 of SAE J1979

Calibration ID

Service $09 of SAE J1979

DTC

1st trip DTC

Freeze Frame

data

1st trip Freeze

Frame data

SRT status

SRT code

Test value

CONSULT-II

×

×

×

×

×

×

—

GST

×

×

×

—

×

×

×

ECM

×

×

*

—

—

×

—

—

Items

MIL

DTC

1st trip DTC

1st trip

2nd trip

1st trip

displaying

2nd trip

displaying

1st trip

displaying

2nd trip

display-

ing

Blinking

Lighting

up

Blinking

Lighting

up

Misfire (Possible three way cata-
lyst damage) — DTC: P0300 -
P0306 is being detected

×

—

—

—

—

—

×

—

Misfire (Possible three way cata-
lyst damage) — DTC: P0300 -
P0306 is being detected

—

—

×

—

—

×

—

—

One trip detection diagnoses
(Refer to

.)

—

×

—

—

×

—

—

—

Except above

—

—

—

×

—

×

×

—

EC-46

ON BOARD DIAGNOSTIC (OBD) SYSTEM

Revision: 2006 August

2006 Murano

The fail-safe function also operates when above diagnoses except MIL circuit are detected and demands the
driver to repair the malfunction.

Emission-Related Diagnostic Information

NBS002Z3

EMISSION-RELATED DIAGNOSTIC INFORMATION ITEMS

×

:Applicable —: Not applicable

Engine operating condition in fail-safe mode

Engine speed will not rise more than 2,500 rpm due to the fuel cut

Items

(CONSULT-II screen terms)

DTC*

1

SRT code

Test value/

Test limit

(GST only)

Trip

MIL

Reference

page

CONSULT-II

GST*

2

ECM*

3

CAN COMM CIRCUIT

U1000

1000*

4

—

—

1

×

CAN COMM CIRCUIT

U1001

1001*

4

—

—

2

—

CONTROL UNIT(CAN)

U1010

1010

—

—

1

×

NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.

P0000

0000

—

—

—

Flashing*

6

—

INT/V TIM CONT-B1

P0011

0011

—

—

2

×

INT/V TIM CONT-B2

P0021

0021

—

—

2

×

A/F SEN1 HTR (B1)

P0031

0031

—

×

2

×

A/F SEN1 HTR (B1)

P0032

0032

—

×

2

×

HO2S2 HTR (B1)

P0037

0037

—

×

2

×

HO2S2 HTR (B1)

P0038

0038

—

×

2

×

A/F SEN1 HTR (B2)

P0051

0051

—

×

2

×

A/F SEN1 HTR (B2)

P0052

0052

—

×

2

×

HO2S2 HTR (B2)

P0057

0057

—

×

2

×

HO2S2 HTR (B2)

P0058

0058

—

×

2

×

INT/V TIM V/CIR-B1

P0075

0075

—

—

2

×

INT/V TIM V/CIR-B2

P0081

0081

—

—

2

×

MAF SEN/CIRCUIT

P0101

0101

—

—

2

×

MAF SEN/CIRCUIT

P0102

0102

—

—

1

×

MAF SEN/CIRCUIT

P0103

0103

—

—

1

×

IAT SEN/CIRCUIT

P0112

0112

—

—

2

×

IAT SEN/CIRCUIT

P0113

0113

—

—

2

×

ECT SEN/CIRC

P0117

0117

—

—

1

×

ECT SEN/CIRC

P0118

0118

—

—

1

×

TP SEN 2/CIRC

P0122

0122

—

—

1

×

TP SEN 2/CIRC

P0123

0123

—

—

1

×

ECT SENSOR

P0125

0125

—

—

2

×

IAT SENSOR

P0127

0127

—

—

2

×

THERMSTAT FNCTN

P0128

0128

—

—

2

×

A/F SENSOR1 (B1)

P0130

0130

—

×

2

×

A/F SENSOR1 (B1)

P0131

0131

—

×

2

×

A/F SENSOR1 (B1)

P0132

0132

—

×

2

×

A/F SENSOR1 (B1)

P0133

0133

×

×

2

×

HO2S2 (B1)

P0137

0137

×

×

2

×

HO2S2 (B1)

P0138

0138

×

×

2

×

HO2S2 (B1)

P0139

0139

×

×

2

×

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-47

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

A/F SENSOR1 (B2)

P0150

0150

—

×

2

×

A/F SENSOR1 (B2)

P0151

0151

—

×

2

×

A/F SENSOR1 (B2)

P0152

0152

—

×

2

×

A/F SENSOR1 (B2)

P0153

0153

×

×

2

×

HO2S2 (B2)

P0157

0157

×

×

2

×

HO2S2 (B2)

P0158

0158

×

×

2

×

HO2S2 (B2)

P0159

0159

×

×

2

×

FUEL SYS-LEAN-B1

P0171

0171

—

—

2

×

FUEL SYS-RICH-B1

P0172

0172

—

—

2

×

FUEL SYS-LEAN-B2

P0174

0174

—

—

2

×

FUEL SYS-RICH-B2

P0175

0175

—

—

2

×

FTT SENSOR

P0181

0181

—

—

2

×

FTT SEN/CIRCUIT

P0182

0182

—

—

2

×

FTT SEN/CIRCUIT

P0183

0183

—

—

2

×

TP SEN 1/CIRC

P0222

0222

—

—

1

×

TP SEN 1/CIRC

P0223

0223

—

—

1

×

MULTI CYL MISFIRE

P0300

0300

—

—

2

×

CYL 1 MISFIRE

P0301

0301

—

—

2

×

CYL 2 MISFIRE

P0302

0302

—

—

2

×

CYL 3 MISFIRE

P0303

0303

—

—

2

×

CYL 4 MISFIRE

P0304

0304

—

—

2

×

CYL 5 MISFIRE

P0305

0305

—

—

2

×

CYL 6 MISFIRE

P0306

0306

—

—

2

×

KNOCK SEN/CIRC-B1

P0327

0327

—

—

2

—

KNOCK SEN/CIRC-B1

P0328

0328

—

—

2

—

CKP SEN/CIRCUIT

P0335

0335

—

—

2

×

CMP SEN/CIRC-B1

P0340

0340

—

—

2

×

CMP SEN/CIRC-B2

P0345

0345

—

—

2

×

TW CATALYST SYS-B1

P0420

0420

×

×

2

×

TW CATALYST SYS-B2

P0430

0430

×

×

2

×

EVAP PURG FLOW/MON

P0441

0441

×

×

2

×

EVAP SMALL LEAK

P0442

0442

×

×

2

×

PURG VOLUME CONT/V

P0443

0443

—

—

2

×

PURG VOLUME CONT/V

P0444

0444

—

—

2

×

PURG VOLUME CONT/V

P0445

0445

—

—

2

×

VENT CONTROL VALVE

P0447

0447

—

—

2

×

VENT CONTROL VALVE

P0448

0448

—

—

2

×

EVAP SYS PRES SEN

P0451

0451

—

—

2

×

EVAP SYS PRES SEN

P0452

0452

—

—

2

×

EVAP SYS PRES SEN

P0453

0453

—

—

2

×

EVAP GROSS LEAK

P0455

0455

—

—

2

×

EVAP VERY SML LEAK

P0456

0456

×

*

7

×

2

×

Items

(CONSULT-II screen terms)

DTC*

1

SRT code

Test value/

Test limit

(GST only)

Trip

MIL

Reference

page

CONSULT-II

GST*

2

ECM*

3

EC-48

ON BOARD DIAGNOSTIC (OBD) SYSTEM

Revision: 2006 August

2006 Murano

FUEL LEV SEN SLOSH

P0460

0460

—

—

2

×

FUEL LEVEL SENSOR

P0461

0461

—

—

2

×

FUEL LEVL SEN/CIRC

P0462

0462

—

—

2

×

FUEL LEVL SEN/CIRC

P0463

0463

—

—

2

×

VEH SPEED SEN/CIRC*

5

P0500

0500

—

—

2

×

ISC SYSTEM

P0506

0506

—

—

2

×

ISC SYSTEM

P0507

0507

—

—

2

×

PW ST P SEN/CIRC

P0550

0550

—

—

2

—

ECM BACK UP/CIRCUIT

P0603

0603

—

—

2

×

ECM

P0605

0605

—

—

1 or 2

×

or —

SENSOR POWER/CIRC

P0643

0643

—

—

1

×

PNP SW/CIRC

P0705

0705

—

—

2

×

ATF TEMP SEN/CIRC

P0710

0710

—

—

1

×

INPUT SPD SEN/CIRC

P0715

0715

—

—

2

×

VEH SPD SEN/CIR AT*

5

P0720

0720

—

—

2

×

TCC SOLENOID/CIRC

P0740

0740

—

—

2

×

A/T TCC S/V FNCTN

P0744

0744

—

—

2

×

L/PRESS SOL/CIRC

P0745

0745

—

—

2

×

PRS CNT SOL/A FCTN

P0746

0746

—

—

1

×

PRS CNT SOL/B FCTN

P0776

0776

—

—

2

×

PRS CNT SOL/B CIRC

P0778

0778

—

—

2

×

TR PRS SENS/A CIRC

P0840

0840

—

—

2

×

TR PRS SENS/B CIRC

P0845

0845

—

—

2

×

P-N POS SW/CIRCUIT

P0850

0850

—

—

2

×

CLOSED LOOP-B1

P1148

1148

—

—

1

×

CLOSED LOOP-B2

P1168

1168

—

—

1

×

TCS C/U FUNCTN

P1211

1211

—

—

2

—

TCS/CIRC

P1212

1212

—

—

2

—

ENG OVER TEMP

P1217

1217

—

—

1

×

CTP LEARNING

P1225

1225

—

—

2

—

CTP LEARNING

P1226

1226

—

—

2

—

COLD START CONTROL

P1421

1421

—

—

2

×

ASCD SW

P1564

1564

—

—

1

—

ASCD BRAKE SW

P1572

1572

—

—

1

—

ASCD VHL SPD SEN

P1574

1574

—

—

1

—

NATS MALFUNCTION

P1610 -

P1615

1610 - 1615

—

—

2

—

CVT C/U FUNCT

P1700

1700

—

—

1

—

IN PULY SPEED

P1715

1715

—

—

2

—

V/SP SEN (A/T OUT)

P1720

1720

—

—

2

—

LU-SLCT SOL/CIRC

P1740

1740

—

—

2

×

STEP MOTR CIRC

P1777

1777

—

—

1

×

Items

(CONSULT-II screen terms)

DTC*

1

SRT code

Test value/

Test limit

(GST only)

Trip

MIL

Reference

page

CONSULT-II

GST*

2

ECM*

3

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-49

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*6: When the ECM is in the mode of displaying SRT status, MIL may flash. For the details, refer to

EC-54, "How to Display SRT Status"

.

*7: SRT code will not be set if the self-diagnostic result is NG.

STEP MOTR FNC

P1778

1778

—

—

2

×

VIAS S/V CIRC

P1800

1800

—

—

2

—

BRAKE SW/CIRCUIT

P1805

1805

—

—

2

—

ETC MOT PWR

P2100

2100

—

—

1

×

ETC FUNCTION/CIRC

P2101

2101

—

—

1

×

ETC MOT PWR

P2103

2103

—

—

1

×

ETC MOT

P2118

2118

—

—

1

×

ETC ACTR

P2119

2119

—

—

1

×

APP SEN 1/CIRC

P2122

2122

—

—

1

×

APP SEN 1/CIRC

P2123

2123

—

—

1

×

APP SEN 2/CIRC

P2127

2127

—

—

1

×

APP SEN 2/CIRC

P2128

2128

—

—

1

×

TP SENSOR

P2135

2135

—

—

1

×

APP SENSOR

P2138

2138

—

—

1

×

A/F SENSOR1 (B1)

P2A00

2A00

—

×

2

×

A/F SENSOR1 (B2)

P2A03

2A03

—

×

2

×

Items

(CONSULT-II screen terms)

DTC*

1

SRT code

Test value/

Test limit

(GST only)

Trip

MIL

Reference

page

CONSULT-II

GST*

2

ECM*

3

EC-50

ON BOARD DIAGNOSTIC (OBD) SYSTEM

Revision: 2006 August

2006 Murano

DTC AND 1ST TRIP DTC

The 1st trip DTC (whose number is the same as the DTC number) is displayed for the latest self-diagnostic
result obtained. If the ECM memory was cleared previously, and the 1st trip DTC did not reoccur, the 1st trip
DTC will not be displayed.
If a malfunction is detected during the 1st trip, the 1st trip DTC is stored in the ECM memory. The MIL will not
light up (two trip detection logic). If the same malfunction is not detected in the 2nd trip (meeting the required
driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the
2nd trip, both the 1st trip DTC and DTC are stored in the ECM memory and the MIL lights up. In other words,
the DTC is stored in the ECM memory and the MIL lights up when the same malfunction occurs in two consec-
utive trips. If a 1st trip DTC is stored and a non-diagnostic operation is performed between the 1st and 2nd
trips, only the 1st trip DTC will continue to be stored. For malfunctions that blink or light up the MIL during the
1st trip, the DTC and 1st trip DTC are stored in the ECM memory.
Procedures for clearing the DTC and the 1st trip DTC from the ECM memory are described in

TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION"

For malfunctions in which 1st trip DTCs are displayed, refer to

EC-46, "EMISSION-RELATED DIAGNOSTIC

INFORMATION ITEMS"

. These items are required by legal regulations to continuously monitor the system/

component. In addition, the items monitored non-continuously are also displayed on CONSULT-II.
1st trip DTC is specified in Service $07 of SAE J1979. 1st trip DTC detection occurs without lighting up the MIL
and therefore does not warn the driver of a malfunction. However, 1st trip DTC detection will not prevent the
vehicle from being tested, for example during Inspection/Maintenance (I/M) tests.
When a 1st trip DTC is detected, check, print out or write down and erase (1st trip) DTC and Freeze Frame
data as specified in Work Flow procedure Step 2, refer to

EC-81, "WORK FLOW"

. Then perform DTC Confir-

mation Procedure or Overall Function Check to try to duplicate the malfunction. If the malfunction is dupli-
cated, the item requires repair.

How to Read DTC and 1st Trip DTC

DTC and 1st trip DTC can be read by the following methods.

With CONSULT-II
With GST

CONSULT-II or GST (Generic Scan Tool) Examples: P0340, P0850, P1148, etc.
These DTCs are prescribed by SAE J2012.
(CONSULT-II also displays the malfunctioning component or system.)

No Tools

The number of blinks of the MIL in the Diagnostic Test Mode II (Self-Diagnostic Results) indicates the DTC.
Example: 0340, 0850, 1148, etc.
These DTCs are controlled by NISSAN.

●

1st trip DTC No. is the same as DTC No.

●

Output of a DTC indicates a malfunction. However, GST or the Diagnostic Test Mode II do not indi-
cate whether the malfunction is still occurring or has occurred in the past and has returned to nor-
mal. CONSULT-II can identify malfunction status as shown below. Therefore, using CONSULT-II (if
available) is recommended.

A sample of CONSULT-II display for DTC and 1st trip DTC is shown below. DTC or 1st trip DTC of a malfunc-
tion is displayed in SELF-DIAGNOSTIC RESULTS mode of CONSULT-II. Time data indicates how many times
the vehicle was driven after the last detection of a DTC.
If the DTC is being detected currently, the time data will be [0].
If a 1st trip DTC is stored in the ECM, the time data will be [1t].

PBIB0911E

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-51

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

FREEZE FRAME DATA AND 1ST TRIP FREEZE FRAME DATA

The ECM records the driving conditions such as fuel system status, calculated load value, engine coolant tem-
perature, short term fuel trim, long term fuel trim, engine speed, vehicle speed, absolute throttle position, base
fuel schedule and intake air temperature at the moment a malfunction is detected.
Data which are stored in the ECM memory, along with the 1st trip DTC, are called 1st trip freeze frame data.
The data, stored together with the DTC data, are called freeze frame data and displayed on CONSULT-II or
GST. The 1st trip freeze frame data can only be displayed on the CONSULT-II screen, not on the GST. For
details, see

EC-115, "Freeze Frame Data and 1st Trip Freeze Frame Data"

.

Only one set of freeze frame data (either 1st trip freeze frame data or freeze frame data) can be stored in the
ECM. 1st trip freeze frame data is stored in the ECM memory along with the 1st trip DTC. There is no priority
for 1st trip freeze frame data and it is updated each time a different 1st trip DTC is detected. However, once
freeze frame data (2nd trip detection/MIL on) is stored in the ECM memory, 1st trip freeze frame data is no
longer stored. Remember, only one set of freeze frame data can be stored in the ECM. The ECM has the fol-
lowing priorities to update the data.

For example, the EGR malfunction (Priority: 2) was detected and the freeze frame data was stored in the 2nd
trip. After that when the misfire (Priority: 1) is detected in another trip, the freeze frame data will be updated
from the EGR malfunction to the misfire. The 1st trip freeze frame data is updated each time a different mal-
function is detected. There is no priority for 1st trip freeze frame data. However, once freeze frame data is
stored in the ECM memory, 1st trip freeze data is no longer stored (because only one freeze frame data or 1st
trip freeze frame data can be stored in the ECM). If freeze frame data is stored in the ECM memory and freeze
frame data with the same priority occurs later, the first (original) freeze frame data remains unchanged in the
ECM memory.
Both 1st trip freeze frame data and freeze frame data (along with the DTCs) are cleared when the ECM mem-
ory is erased. Procedures for clearing the ECM memory are described in

EC-58, "HOW TO ERASE EMIS-

SION-RELATED DIAGNOSTIC INFORMATION"

SYSTEM READINESS TEST (SRT) CODE

System Readiness Test (SRT) code is specified in Service $01 of SAE J1979.
As part of an enhanced emissions test for Inspection & Maintenance (I/M), certain states require the status of
SRT be used to indicate whether the ECM has completed self-diagnosis of major emission systems and com-
ponents. Completion must be verified in order for the emissions inspection to proceed.
If a vehicle is rejected for a State emissions inspection due to one or more SRT items indicating “INCMP”, use
the information in this Service Manual to set the SRT to “CMPLT”.
In most cases the ECM will automatically complete its self-diagnosis cycle during normal usage, and the SRT
status will indicate “CMPLT” for each application system. Once set as “CMPLT”, the SRT status remains
“CMPLT” until the self-diagnosis memory is erased.
Occasionally, certain portions of the self-diagnostic test may not be completed as a result of the customer's
normal driving pattern; the SRT will indicate “INCMP” for these items.

NOTE:
The SRT will also indicate “INCMP” if the self-diagnosis memory is erased for any reason or if the ECM mem-
ory power supply is interrupted for several hours.
If, during the state emissions inspection, the SRT indicates “CMPLT” for all test items, the inspector will con-
tinue with the emissions test. However, if the SRT indicates “INCMP” for one or more of the SRT items the
vehicle is returned to the customer untested.

NOTE:
If MIL is ON during the state emissions inspection, the vehicle is also returned to the customer untested even
though the SRT indicates “CMPLT” for all test items. Therefore, it is important to check SRT (“CMPLT”) and
DTC (No DTCs) before the inspection.

Priority

Items

1

Freeze frame data

Misfire — DTC: P0300 - P0306
Fuel Injection System Function — DTC: P0171, P0172, P0174, P0175

2

Except the above items (Includes CVT related items)

3

1st trip freeze frame data

EC-52

ON BOARD DIAGNOSTIC (OBD) SYSTEM

Revision: 2006 August

2006 Murano

SRT Item

The table below shows required self-diagnostic items to set the SRT to “CMPLT”.

*: If completion of several SRTs is required, perform driving patterns (DTC confirmation procedure), one by one based on the priority for
models with CONSULT-II.

SRT Set Timing

SRT is set as “CMPLT” after self-diagnosis has been performed one or more times. Completion of SRT is
done regardless of whether the result is OK or NG. The set timing is different between OK and NG results and
is shown in the table below.

OK: Self-diagnosis is carried out and the result is OK.
NG: Self-diagnosis is carried out and the result is NG.
—: Self-diagnosis is not carried out.

When all SRT related self-diagnoses showed OK results in a single cycle (Ignition OFF-ON-OFF), the SRT will
indicate “CMPLT”.

→

Case 1 above

When all SRT related self-diagnoses showed OK results through several different cycles, the SRT will indicate
“CMPLT” at the time the respective self-diagnoses have at least one OK result.

→

Case 2 above

If one or more SRT related self-diagnoses showed NG results in 2 consecutive cycles, the SRT will also indi-
cate “CMPLT”.

→

Case 3 above

The table above shows that the minimum number of cycles for setting SRT as “INCMP” is one (1) for each
self-diagnosis (Case 1 & 2) or two (2) for one of self-diagnoses (Case 3). However, in preparation for the state
emissions inspection, it is unnecessary for each self-diagnosis to be executed twice (Case 3) for the following
reasons:

SRT item

(CONSULT-II indication)

Performance

Priority*

Required self-diagnostic items to set the SRT to “CMPLT”

Corresponding

DTC No.

CATALYST

2

Three way catalyst function

P0420, P0430

EVAP SYSTEM

2

EVAP control system purge flow monitoring

P0441

1

EVAP control system

P0442

2

EVAP control system

P0456

HO2S

2

Air fuel ratio (A/F) sensor 1

P0133, P0153

Heated oxygen sensor 2

P0137, P0157

Heated oxygen sensor 2

P0138, P0158

Heated oxygen sensor 2

P0139, P0159

Self-diagnosis result

Example

Diagnosis

Ignition cycle

←

ON

→

OFF

←

ON

→

OFF

←

ON

→

OFF

←

ON

→

All OK

Case 1

P0400

OK (1)

— (1)

OK (2)

— (2)

P0402

OK (1)

— (1)

— (1)

OK (2)

P1402

OK (1)

OK (2)

— (2)

— (2)

SRT of EGR

“CMPLT”

“CMPLT”

“CMPLT”

“CMPLT”

Case 2

P0400

OK (1)

— (1)

— (1)

— (1)

P0402

— (0)

— (0)

OK (1)

— (1)

P1402

OK (1)

OK (2)

— (2)

— (2)

SRT of EGR

“INCMP”

“INCMP”

“CMPLT”

“CMPLT”

NG exists

Case 3

P0400

OK

OK

—

—

P0402

—

—

—

—

P1402

NG

—

NG

NG

(Consecutive

NG)

(1st trip)

DTC

1st trip DTC

—

1st trip DTC

DTC

(= MIL ON)

SRT of EGR

“INCMP”

“INCMP”

“INCMP”

“CMPLT”

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-53

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

●

The SRT will indicate “CMPLT” at the time the respective self-diagnoses have one (1) OK result.

●

The emissions inspection requires “CMPLT” of the SRT only with OK self-diagnosis results.

●

When, during SRT driving pattern, 1st trip DTC (NG) is detected prior to “CMPLT” of SRT, the self-diagno-
sis memory must be erased from ECM after repair.

●

If the 1st trip DTC is erased, all the SRT will indicate “INCMP”.

NOTE:
SRT can be set as “CMPLT” together with the DTC(s). Therefore, DTC check must always be carried out
prior to the state emission inspection even though the SRT indicates “CMPLT”.

SRT Service Procedure

If a vehicle has failed the state emissions inspection due to one or more SRT items indicating “INCMP”, review
the flowchart diagnostic sequence on the next page.

*1

*2

*3

PBIB2320E

EC-54

ON BOARD DIAGNOSTIC (OBD) SYSTEM

Revision: 2006 August

2006 Murano

How to Display SRT Status

WITH CONSULT-II

Selecting “SRT STATUS” in “DTC CONFIRMATION” mode with
CONSULT-II.
For items whose SRT codes are set, a “CMPLT” is displayed on the
CONSULT-II screen; for items whose SRT codes are not set,
“INCMP” is displayed.
A sample of CONSULT-II display for SRT code is shown at right.
“INCMP” means the self-diagnosis is incomplete and SRT is not set.
“CMPLT” means the self-diagnosis is complete and SRT is set.
NOTE:
Though displayed on the CONSULT-II screen, “HO2S HTR” is not
SRT item.

WITH GST

Selecting Service $01 with GST (Generic Scan Tool)

NO TOOLS

A SRT code itself can not be displayed while only SRT status can be.

1.

Turn ignition switch ON and wait 20 seconds.

2.

SRT status is indicated as shown below.

–

When all SRT codes are set, MIL lights up continuously.

–

When any SRT codes are not set, MIL will flash periodically for 10 seconds.

How to Set SRT Code

To set all SRT codes, self-diagnosis for the items indicated above must be performed one or more times. Each
diagnosis may require a long period of actual driving under various conditions.

WITH CONSULT-II

Perform corresponding DTC Confirmation Procedure one by one based on Performance Priority in the table
on

WITHOUT CONSULT-II

The most efficient driving pattern in which SRT codes can be properly set is explained on the next page. The
driving pattern should be performed one or more times to set all SRT codes.

SEF935Z

PBIB2317E

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-55

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

Driving Pattern

PBIB2906E

EC-56

ON BOARD DIAGNOSTIC (OBD) SYSTEM

Revision: 2006 August

2006 Murano

●

The time required for each diagnosis varies with road surface conditions, weather, altitude, individual driv-
ing habits, etc.
Zone A refers to the range where the time, required for the diagnosis under normal conditions*, is the
shortest.
Zone B refers to the range where the diagnosis can still be performed if the diagnosis is not completed
within zone A.

*: Normal conditions refer to the following:

●

Sea level

●

Flat road

●

Ambient air temperature: 20 - 30

°

C (68 - 86

°

F)

●

Diagnosis is performed as quickly as possible under normal conditions.
Under different conditions [For example: ambient air temperature other than 20 - 30

°

C (68 - 86

°

F)], diag-

nosis may also be performed.

Pattern 1:

●

The engine is started at the engine coolant temperature of

−

10 to 35

°

C (14 to 95

°

F)

(where the voltage between the ECM terminal 73 and ground is 3.0 - 4.3V).

●

The engine must be operated at idle speed until the engine coolant temperature is greater than
70

°

C (158

°

F) (where the voltage between the ECM terminal 73 and ground is lower than 1.4V).

●

The engine is started at the fuel tank temperature of warmer than 0

°

C (32

°

F) (where the voltage

between the ECM terminal 107 and ground is less than 4.1V).

Pattern 2:

●

When steady-state driving is performed again even after it is interrupted, each diagnosis can be con-
ducted. In this case, the time required for diagnosis may be extended.

Pattern 3:

●

Operate vehicle following the driving pattern shown in the figure.

●

Release the accelerator pedal during decelerating vehicle speed
from 90 km/h (56 MPH) to 0 km/h (0 MPH).

Pattern 4:

●

The accelerator pedal must be held very steady during steady-
state driving.

●

If the accelerator pedal is moved, the test must be conducted all
over again.

*1: Depress the accelerator pedal until vehicle speed is 90 km/h (56
MPH), then release the accelerator pedal and keep it released for
more than 10 seconds. Depress the accelerator pedal until vehicle
speed is 90 km/h (56 MPH) again.
*2: Checking the vehicle speed with GST is advised.

Suggested Transmission Gear Position
Set the shift lever in the D position.

TEST VALUE AND TEST LIMIT (GST ONLY — NOT APPLICABLE TO CONSULT-II)

The following is the information specified in Service $06 of SAE J1979.
The test value is a parameter used to determine whether a system/circuit diagnostic test is OK or NG while
being monitored by the ECM during self-diagnosis. The test limit is a reference value which is specified as the
maximum or minimum value and is compared with the test value being monitored.
These data (test value and test limit) are specified by Test ID (TID) and Component ID (CID) and can be dis-
played on the GST screen.

PBIB2244E

SRT item

Self-diagnostic test item

DTC

Test value (GST display)

Test limit

Unit

TID

CID

CATALYST

Three way catalyst function (Bank 1)

P0420

01H

01H

Max.

1/128

P0420

02H

81H

Min.

1

Three way catalyst function (Bank 2)

P0430

03H

02H

Max.

1/128

P0430

04H

82H

Min.

1

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-57

C

D

E

F

G

H

I

J

K

L

M

A

EC

Revision: 2006 August

2006 Murano

EVAP

SYSTEM

EVAP control system (Small leak)

P0442

05H

03H

Max.

1/128 mm

2

EVAP control system purge flow monitoring

P0441

06H

83H

Min.

20 mV

EVAP control system (Very small leak)

P0456

07H

03H

Max.

1/128 mm

2

HO2S

A/F sensor 1 (Bank 1)

P0131

41H

8EH

Min.

5 mV

P0132

42H

0EH

Max.

5 mV

P2A00

43H

0EH

Max.

0.002

P2A00

44H

8EH

Min. 0.002

P0133

45H

8EH

Min. 0.004

P0130

46H

0EH

Max.

5 mV

P0130

47H

8EH

Min. 5

mV

P0133

48H

8EH

Min. 0.004

A/F sensor 1 (Bank 2)

P0151

4CH

8FH

Min.

5 mV

P0152

4DH

0FH

Max.

5 mV

P2A03

4EH

0FH

Max.

0.002

P2A03

4FH

8FH

Min.

0.002

P0153

50H

8FH

Min.

0.004

P0150

51H

0FH

Max.

5 mV

P0150

52H

8FH

Min.

5 mV

P0153

53H

8FH

Min.

0.004

Heated oxygen sensor 2 (Bank 1)

P0139

19H

86H

Min.

10mV/500 ms

P0137

1AH

86H

Min.

10 mV

P0138

1BH

06H

Max.

10 mV

P0138

1CH

06H

Max.

10 mV

Heated oxygen sensor 2 (Bank 2)

P0159

21H

87H

Min.

10mV/500 ms

P0157

22H

87H

Min.

10 mV

P0158

23H

07H

Max.

10 mV

P0158 24H

07H

Max.

10

mV

HO2S HTR

A/F sensor 1 heater (Bank 1)

P0032

57H

10H

Max.

5 mV

P0031

58H

90H

Min.

5 mV

A/F sensor 1 heater (Bank 2)

P0052

59H

11H

Max.

5 mV

P0051

5AH

91H

Min.

5 mV

Heated oxygen sensor 2 heater (Bank 1)

P0038

2DH

0AH

Max.

20 mV

P0037

2EH

8AH

Min.

20 mV

Heated oxygen sensor 2 heater (Bank 2)

P0058

2FH

0BH

Max.

20 mV

P0057

30H

8BH

Min.

20 mV

SRT item

Self-diagnostic test item

DTC

Test value (GST display)

Test limit

Unit

TID

CID

EC-58

ON BOARD DIAGNOSTIC (OBD) SYSTEM

Revision: 2006 August

2006 Murano

HOW TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION
How to Erase DTC

WITH CONSULT-II

The emission related diagnostic information in the ECM can be erased by selecting “ERASE” in the “SELF-
DIAG RESULTS” mode with CONSULT-II.
If DTCs are displayed for both ECM and TCM (Transmission control module), they need to be erased individu-
ally from the ECM and TCM (Transmission control module).

NOTE:
If the DTC is not for CVT related items (see

), skip steps 2 through 4.

1.

If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.

2.

Turn CONSULT-II ON and touch “TRANSMISSION”.

3.

Touch “SELF-DIAG RESULTS”.

4.

Touch “ERASE”. [The DTC in the TCM (Transmission control module) will be erased.] Then touch “BACK”
twice.

5.

Touch “ENGINE”.

6.

Touch “SELF-DIAG RESULTS”.

7.

Touch “ERASE”. (The DTC in the ECM will be erased.)

WITH GST

The emission related diagnostic information in the ECM can be erased by selecting Service $04 with GST.

NOTE:
If the DTC is not for CVT related items (see

), skip step 2.

1.

If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.

SCIA5442E

Content .. 77 78 79 80 ..