Nissan X-Trail 32. Manual - part 1630

PB-46

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORK FLOW

Inspection re-
sult

Self-diagnosis result

Battery condition

†

 Normal

†

 Abnormal (

)

†

 Not confirmed

Harness and connector 
condition

†

 Normal

†

 Abnormal (

)

†

 Not confirmed

Brake caliper assembly 
condition

†

 Normal

†

 Abnormal (

)

†

 Not confirmed

Rear brake pad condition

†

 Normal

†

 Abnormal (

)

†

 Not confirmed

Rear disc rotor condition

†

 Normal

†

 Abnormal (

)

†

 Not confirmed

Other condition

Interview sheet

Customer 
name

MR/MS

Registration num-
ber

Initial year 
registration

Vehicle type

VIN

Storage date

Engine

Mileage

                 km (              Mile)

CONFIGURATION (ELECTRIC PARKING BRAKE CONTROL MODULE)

PB-47

< BASIC INSPECTION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

CONFIGURATION (ELECTRIC PARKING BRAKE CONTROL MODULE)

Work Procedure

INFOID:0000000010722934

CAUTION:

• Use “Manual Configuration” only when “TYPE ID” of electric parking brake control module cannot

be read.

• After configuration, turn the ignition switch from OFF to ON and check that the brake system warn-

ing lamp turns OFF after staying illuminated for approximately two seconds.

• If an error occurs during configuration, start over from the beginning.

1.

CHECKING TYPE ID (1)

Use FAST (service parts catalogue) to search electric parking brake control module of the applicable vehicle
and find “Type ID”.

Is “Type ID” displayed?

YES

>> Print out “Type ID” and GO TO 2.

NO

>> “Configuration” is not required for electric parking brake control module. Replace in the usual

manner. Refer to 

PB-153, "Removal and Installation"

.

2.

CHECKING TYPE ID (2)

CONSULT Configuration

1.

Select “Before Replace ECU” of “Read/Write Configuration”.

2.

Check that “Type ID” is displayed on the CONSULT screen.

Is “Type ID” displayed?

YES

>> GO TO 3.

NO

>> GO TO 7.

3.

VERIFYING TYPE ID (1)

CONSULT Configuration

Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 4.

4.

SAVING TYPE ID

CONSULT Configuration

Save “Type ID” on CONSULT.

>> GO TO 5.

5.

REPLACING ELECTRIC PARKING BRAKE CONTROL MODULE (1)

Replace the electric parking brake control module. Refer to 

PB-153, "Removal and Installation"

.

CAUTION:

Never perform the following work items:
• Change of system mode
• Calibration of G sensor
• Reset of clutch stroke sensor (M/T models)
• Adjustment of rear brake caliper initial position
• Operation of rear brake caliper
• Release of rear brake caliper
• Automatic activation ON setting (CVT models)

>> GO TO 6.

6.

WRITING (AUTOMATIC WRITING)

CONSULT Configuration

PB-48

< BASIC INSPECTION >

CONFIGURATION (ELECTRIC PARKING BRAKE CONTROL MODULE)

1.

Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.

2.

Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the electric parking brake control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 9.

7.

REPLACING ELECTRIC PARKING BRAKE CONTROL MODULE (2)

Replace the electric parking brake control module. Refer to 

PB-153, "Removal and Installation"

.

CAUTION:

Never perform the following work items:
• Change of system mode
• Calibration of G sensor
• Reset of clutch stroke sensor (M/T models)
• Adjustment of rear brake caliper initial position
• Operation of rear brake caliper
• Release of rear brake caliper
• Automatic activation ON setting (CVT models)

>> GO TO 8.

8.

WRITING (MANUAL WRITING)

CONSULT Configuration

1.

Select “Manual Configuration”.

2.

Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the elec-
tric parking brake control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 9.

9.

VERIFYING TYPE ID (2)

Compare “Type ID” written into the electric parking brake control module with the one searched by using FAST
(service parts catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 10.

10.

CHECKING VDC WARNING LAMP

1.

Turn the ignition switch OFF.

2.

Turn the ignition switch ON and check that the brake system warning lamp turns OFF after staying illumi-
nated for approximately two seconds.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Perform the self-diagnosis of “EHS/PKB”.

11.

PERFORMING SUPPLEMENTARY WORK

1.

Perform the calibration of G sensor. Refer to 

PB-57, "Work Procedure"

.

2.

Perform the reset of clutch stroke sensor. Refer to 

PB-59, "Work Procedure"

. (M/T models)

3.

Perform the adjustment of rear brake caliper initial position. Refer to 

PB-55, "Work Procedure"

.

4.

Perform the operation of rear brake caliper. Refer to 

PB-61, "Work Procedure"

.

5.

Perform the release of rear brake caliper. Refer to 

PB-63, "Work Procedure"

.

6.

Perform the change of system mode. Refer to 

PB-65, "Work Procedure"

.

7.

Record or print self-diagnosis result and freeze frame data (FFD).

8.

Erase self-diagnosis results.

CONFIGURATION (ELECTRIC PARKING BRAKE CONTROL MODULE)

PB-49

< BASIC INSPECTION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

>> End of work.