Juke F15 (2012 year). Service Repair Manual - part 206

EXL-66

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

LICENSE PLATE LAMP CIRCUIT

WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check

INFOID:0000000006478924

1.

CHECK TAIL LAMP (RH) OPERATION

Check that the tail lamp (RH) is turned ON.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-62, "WITH DAYTIME RUNNING LIGHT SYSTEM : Compo-

nent Function Check"

.

2.

CHECK LICENSE PLATE LAMP OPERATION

CONSULT-III ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the lighting switch, check that the license plate lamp is turned ON.

Is the inspection result normal?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to 

EXL-66, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"

.

WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure

INFOID:0000000006478925

1.

CHECK LICENSE PLATE LAMP BULB

Check the applicable lamp bulb.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace bulb.

2.

CHECK LICENSE PLATE LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Remove daytime running light relay.

3.

Disconnect back door opener switch connector.

4.

Check continuity between daytime running light relay harness connector and back door opener switch
harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

TAIL

: License plate lamp ON

Off

: License plate lamp OFF

Daytime running light relay

Back door opener switch

Continuity

Connector

Terminal

Connector

Terminal

E82

5

D107

5

Existed

Back door opener switch

Ground

Continuity

Connector

Terminal

D107

6

Existed

LIGHT & RAIN SENSOR

EXL-67

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LIGHT & RAIN SENSOR

Component Function Check

INFOID:0000000006452196

1.

CHECK LIGHT & RAIN SENSOR

1.

Clean light & rain sensor detection area of windshield fully.

2.

Turn ignition switch ON.

3.

Turn lighting switch AUTO.

4.

With the light & rain sensor illuminating, check the auto light function. 

Is the inspection result normal?

YES

>> Light & rain sensor is normal.

NO

>> Refer to 

EXL-67, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006452197

1.

CHECK LIGHT & RAIN SENSOR FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the fuse after repairing the applicable circuit.

2.

CHECK LIGHT & RAIN SENSOR POWER SUPPLY

1.

Disconnect light & rain sensor connector.

2.

Check voltage between light & rain sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT

Check continuity between light & rain sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK LIGHT & RAIN SENSOR SIGNAL

1.

Connect light & rain sensor connector.

2.

Turn ignition switch ON.

Condition

Auto light function

Light & rain sensor

When illuminating

Not operating

When shutting off light

Operating

Unit

Fuse No.

Capacity

Light & rain sensor

#7

10 A

(+)

(

−

)

Voltage

(Approx.)

Light & rain sensor

Connector

Terminal

R5

1

Ground Battery 

voltage

Light & rain sensor

Ground

Continuity

Connector

Terminal

R5

3

Existed

EXL-68

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

LIGHT & RAIN SENSOR

3.

Check signal between BCM harness connector and ground with oscilloscope.

*1: Without Intelligent Key

*2: With Intelligent Key

Is the inspection result normal?

YES

>> Replace light & rain sensor. 

NO

>> GO TO 5.

5.

CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR OPEN

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and light & rain sensor connector.

3.

Check continuity between BCM harness connector and light & rain sensor harness connector.

*1: Without Intelligent Key

*2: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR SHORT

Check continuity between BCM harness connector and ground.

*1: Without Intelligent Key

*2: With Intelligent Key

Is the inspection result normal?

YES

>> Refer to 

BCS-93, "Removal and Installation"

 (with Intelligent Key), 

BCS-161, "Removal and Instal-

lation"

 (without Intelligent Key).

NO

>> Repair or replace harness.

(+)

(

−

)

Condition

Signal

(Reference value)

BCM

Connector

Terminal

M65*

1

M68*

2

14*

1

11*

2

Ground Ignition 

switch 

ON

Approx. 8.7V

JPMIA0156GB

BCM

Light & rain sensor

Continuity

Connector

Terminal

Connector

Terminal

M65*

1

M68*

2

14*

1

11*

2

R5

2

Existed

BCM

Ground

Continuity

Connector

Terminal

M65*

1

M68*

2

14*

1

11*

2

Not existed

TURN SIGNAL LAMP CIRCUIT

EXL-69

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

TURN SIGNAL LAMP CIRCUIT

Component Function Check

INFOID:0000000006451732

1.

CHECK TURN SIGNAL LAMP

CONSULT-III ACTIVE TEST

1.

Select “FLASHER” of BCM (FLASHER) active test item.

2.

With operating the test items, check that the turn signal lamps is turned ON.

Is the inspection result normal?

YES

>> Turn signal lamp circuit is normal.

NO

>> Refer to 

EXL-69, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006451733

1.

CHECK TURN SIGNAL LAMP BULB

Check the applicable lamp bulb.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace bulb.

2.

CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

1.

Turn ignition switch OFF.

2.

Disconnect front turn signal lamp connector, side turn signal lamp connector and rear combination lamp
connector.

3.

Turn ignition switch ON.

4.

With operating the turn signal switch, check voltage between BCM harness connector and ground.

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

LH

: Turn signal lamps (LH) ON

RH

: Turn signal lamps (RH) ON

Off

: Turn signal lamps OFF

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

B9*

1

M69*

2

49*

1

60*

2

Ground

Turn signal 
switch

LH

OFF

0 V

48*

1

61*

2

RH

OFF

0 V

PKID0926E

PKID0926E

EXL-70

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

TURN SIGNAL LAMP CIRCUIT

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 4.

3.

CHECK TURN SIGNAL LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

3.

Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

4.

CHECK TURN SIGNAL LAMP SHORT CIRCUIT

Check continuity between BCM harness connector and ground.

*

1

: Without Intelligent Key

*

2

: With Intelligent Key

Is the inspection result normal?

BCM

Front turn signal lamp

Continuity

Connector

Terminal

Connector

Terminal

 RH

B9*

1

M69*

2

48*

1

61*

2

E46

1

Existed

 LH

49*

1

60*

2

E27

BCM

Side turn signal lamp

Continuity

Connector

Terminal

Connector

Terminal

 RH

B9*

1

M69*

2

48*

1

61*

2

E40

1

Existed

 LH

49*

1

60*

2

E23

BCM

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

B9*

1

M69*

2

48*

1

61*

2

B59

5

Existed

LH

49*

1

60*

2

B80

BCM

Ground

Continuity

Connector

Terminal

RH

B9

*1

M69

*2

48*

1

61*

2

Not existed

LH

49*

1

60*

2

TURN SIGNAL LAMP CIRCUIT

EXL-71

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

YES

>> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer

to 

BCS-93, "Removal and Installation"

 (with Intelligent Key), 

BCS-161, "Removal and Installation"

(without Intelligent Key).

NO

>> Repair or replace harness.

5.

CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT

Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

Front turn signal lamp

Ground

Continuity

Connector

Terminal

RH

E46

2

Existed

LH

E27

Side turn signal lamp

Ground

Continuity

Connector

Terminal

RH

E40

2

Existed

LH

E23

Rear combination lamp

Ground

Continuity

Connector

Terminal

RH

B59

3

Existed

LH

B80

EXL-72

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HAZARD SWITCH

HAZARD SWITCH

Component Function Check

INFOID:0000000006451734

1.

CHECK HAZARD SWITCH SIGNAL BY CONSULT-III

CONSULT-III DATA MONITOR

1.

Turn the ignition switch ON.

2.

Select “HAZARD SW” of BCM (FLASHER) data monitor item.

3.

With operating the hazard switch, check the monitor status.

Is the inspection result normal?

YES

>> Hazard switch circuit is normal.

NO

>> Refer to 

EXL-72, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006451735

1.

CHECK HAZARD SWITCH SIGNAL INPUT

1.

Turn ignition switch OFF.

2.

Disconnect hazard switch connector.

3.

Check voltage between hazard switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between hazard switch harness connector and BCM harness connector.

*1: Without Intelligent Key

*2: With Intelligent Key

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

Monitor item

Condition

Monitor status

HAZARD SW

Hazard switch

ON

On

OFF

Off

(+)

(

−

)

Voltage (Approx.)

Hazard switch

Connector

Terminal

M45

2

Ground

12 V

Hazard switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M45

2

M65

*1

M68

*2

29

Existed

Hazard switch

Ground

Continuity

Connector

Terminal

M45

2

Not existed

HAZARD SWITCH

EXL-73

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

YES

>> Replace BCM. Refer to 

BCS-93, "Removal and Installation"

 (with Intelligent Key) or 

BCS-161,

"Removal and Installation"

 (without Intelligent Key).

NO

>> Repair or replace harness.

4.

CHECK HAZARD SWITCH GROUND OPEN CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace hazard switch.

NO

>> Repair or replace harness.

Hazard switch

Ground

Continuity

Connector

Terminal

M45

1

Existed

EXL-74

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

WITHOUT DAYTIME RUNNING LIGHT SYSTEM

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table

INFOID:0000000006451740

CAUTION:

Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

headlamp

• Harness between headlamp and 

ground

• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-45, "Component 

Function Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-78, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter 

Data monitor “HI-BEAM IND”

• BCM (HEADLAMP)

Active test “HEADLAMP”

Headlamp (LO) is not 
turned ON.

One side

• Fuse
• Halogen bulb 
• Harness between IPDM E/R and 

headlamp

• Harness between headlamp and 

ground

• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-47, "Component 

Function Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-79, "Diagnosis Procedure"

.

Headlamp is not turned 
OFF.

When ignition switch 
is turned ON.

When ignition switch 
is turned OFF.

IPDM E/R

—

Headlamp HI and LO are not turned ON.

• Harness between headlamp and 

ground

• Halogen bulb

Headlamp ground circuit
Refer to 

EXL-49, "Diagnosis Proce-

dure"

.

Front fog lamp is not 
turned ON.

One side

• Front fog lamp bulb
• Harness between front fog lamp 

relay and front fog lamp

Front fog lamp circuit
Refer to 

EXL-54, "Component 

Function Check"

.

Both side

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-82, "Diagnosis Procedure"

.

Front fog lamp is not turned OFF.

Parking lamp is not turned ON.

• Parking lamp bulb
• Harness between IPDM E/R and 

parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-58, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Component Function Check"

.

Tail lamp is not turned ON.

• Tail lamp bulb
• Harness between IPDM E/R and 

rear combination lamp

• IPDM E/R

Tail lamp circuit
Refer to 

EXL-61, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Component Function Check"

.

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R and 

license plate lamp

License plate lamp circuit
Refer to 

EXL-65, "WITHOUT DAY-

TIME RUNNING LIGHT SYSTEM : 
Component Function Check"

.

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-75

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

WITH DAYTIME RUNNING LIGHT SYSTEM

WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table

INFOID:0000000006479243

CAUTION:

Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.

• Parking lamp, tail lamp and license plate lamp 

are not turned ON.

• Parking lamp, tail lamp and license plate lamp 

are not turned OFF.

(Each illumination is turned ON/OFF.)

Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
Refer to 

EXL-80, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Di-

agnosis Procedure"

.

Turn signal lamp does 
not blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher 
activation.)

• Harness between BCM and each 

turn signal lamp

• Turn signal lamp bulb

Turn signal lamp circuit
Refer to 

EXL-69, "Component 

Function Check"

.

Indicator lamp is in-
cluded.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Turn signal indicator 
lamp does not blink.
(Turn signal indicator 
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp signal
- BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with the ignition switch 
OFF.)

• Combination meter power supply 

and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-51, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard switch 

and BCM

• BCM

Hazard switch
Refer to 

EXL-72, "Component 

Function Check"

.

Rear fog lamp is not 
turned ON.

Rear fog lamp indica-
tor lamp is normal.

• Harness between BCM and rear 

fog lamp

• Rear fog lamp bulb
• BCM

Rear fog lamp circuit
Refer to 

EXL-56, "Component 

Function Check"

.

Rear fog lamp indica-
tor lamp is included.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Rear fog lamp indicator lamp is not turn ON. 
(Rear fog lamp turns ON)

• Rear fog lamp status signal
• Combination meter
• BCM

• Combination meter

Data monitor “RR FOG IND”

• BCM (HEAD LAMP)

Active test “RR FOG LAMP”

Symptom

Possible cause

Inspection item

EXL-76

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom

Possible cause

Inspection item

Headlamp (HI) is not 
turned ON.

One side

• Fuse
• Halogen bulb
• Harness between IPDM E/R and 

headlamp

• Harness between headlamp and 

ground

• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-45, "Component 

Function Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-78, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]

Combination meter

• Combination meter 

Data monitor “HI-BEAM IND”

• BCM (HEADLAMP)

Active test “HEADLAMP”

Headlamp (LO) is not 
turned ON.

One side

• Fuse
• Halogen bulb 
• Harness between IPDM E/R and 

headlamp

• Harness between headlamp and 

ground

• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-47, "Component 

Function Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-79, "Diagnosis Procedure"

.

Headlamp is not turned 
OFF.

When ignition switch 
is turned ON.

When ignition switch 
is turned OFF.

IPDM E/R

—

Headlamp HI and LO are not turned ON.

• Harness between headlamp and 

ground

• Halogen bulb

Headlamp ground circuit
Refer to 

EXL-49, "Diagnosis Proce-

dure"

.

Front fog lamp is not 
turned ON.

One side

• Front fog lamp bulb
• Harness between front fog lamp 

relay and front fog lamp

Front fog lamp circuit
Refer to 

EXL-54, "Component 

Function Check"

.

Both side

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-82, "Diagnosis Procedure"

.

Front fog lamp is not turned OFF.

Parking lamp is not turned ON.

Daytime running light relay

Daytime running light relay circuit
Refer to 

EXL-50, "Component 

Function Check"

.

• Parking lamp bulb
• Harness between parking lamp 

and daytime running relay

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-59, "WITH DAYTIME 

RUNNING LIGHT SYSTEM : Com-
ponent Function Check"

.

Tail lamp is not turned ON.

Daytime running light relay

Daytime running light relay circuit
Refer to 

EXL-50, "Component 

Function Check"

.

• Tail lamp bulb
• Harness between daytime run-

ning relay and rear combination 
lamp

Tail lamp circuit
Refer to 

EXL-62, "WITH DAYTIME 

RUNNING LIGHT SYSTEM : Com-
ponent Function Check"

.

License plate lamp is not turned ON.

Daytime running light relay

Daytime running light relay circuit
Refer to 

EXL-50, "Component 

Function Check"

.

• License plate lamp bulb
• Harness between daytime run-

ning relay and license plate lamp

License plate lamp circuit
Refer to 

EXL-66, "WITH DAYTIME 

RUNNING LIGHT SYSTEM : Com-
ponent Function Check"

.

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-77

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

• Parking lamp, tail 

lamp, lamp and the li-
cense plate lamp are 
not turned ON.

• Parking lamp, tail 

lamp, lamp and li-
cense plate lamp are 
not turned OFF.

Each illumination is 
turned ON/OFF

• Fuse
• Harness between IPDM E/R and 

the daytime running light relay

• Daytime running light relay
• IPDM E/R

Daytime running light relay circuit
Refer to 

EXL-50, "Component 

Function Check"

.

Each illumination is 
not turned ON/OFF

Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
Refer to 

EXL-80, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis 

Procedure"

.

Turn signal lamp does 
not blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher 
activation.)

• Harness between BCM and each 

turn signal lamp

• Turn signal lamp bulb

Turn signal lamp circuit
Refer to 

EXL-69, "Component 

Function Check"

.

Indicator lamp is in-
cluded.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Turn signal indicator 
lamp does not blink.
(Turn signal indicator 
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn signal indicator lamp signal
- BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with the ignition switch 
OFF.)

• Combination meter power supply 

and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-51, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard switch 

and BCM

• BCM

Hazard switch
Refer to 

EXL-72, "Component 

Function Check"

.

Rear fog lamp is not 
turned ON.

Rear fog lamp indica-
tor lamp is normal.

• Harness between BCM and rear 

fog lamp

• Rear fog lamp bulb
• BCM

Rear fog lamp circuit
Refer to 

EXL-56, "Component 

Function Check"

.

Rear fog lamp indica-
tor lamp is included.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Rear fog lamp indicator lamp is not turn ON. 
(Rear fog lamp turns ON)

• Rear fog lamp status signal
• Combination meter
• BCM

• Combination meter

Data monitor “RR FOG IND”

• BCM (HEAD LAMP)

Active test “RR FOG LAMP”

Symptom

Possible cause

Inspection item

EXL-78

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

Description

INFOID:0000000006451741

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.

Diagnosis Procedure

INFOID:0000000006451742

1.

COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT

CONSULT-III DATA MONITOR

1.

Select “HL HI REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace BCM. Refer to 

BCS-93, "Removal and Installation"

 (with Intelligent Key), 

BCS-161,

"Removal and Installation"

 (without Intelligent Key).

3.

HEADLAMP (HI) CIRCUIT INSPECTION

Check the headlamp (HI) circuit. Refer to 

EXL-45, "Component Function Check"

.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace the malfunctioning part.

Monitor item

Condition

Monitor status

HL HI REQ

Lighting switch
(2ND)

HI or PASS

ON

LO

OFF

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

EXL-79

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

Description

INFOID:0000000006451743

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000006451744

1.

CHECK COMBINATION SWITCH

Check the combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT

CONSULT-III DATA MONITOR

1.

Select “HL LO REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace BCM. Refer to 

BCS-93, "Removal and Installation"

 (with Intelligent Key), 

BCS-161,

"Removal and Installation"

 (without Intelligent Key).

3.

HEADLAMP (LO) CIRCUIT INSPECTION

Check the headlamp (LO) circuit. Refer to 

EXL-47, "Component Function Check"

.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace the malfunctioning part.

Monitor item

Condition

Monitor status

HL LO REQ

Lighting switch

2ND

ON

OFF

OFF

EXL-80

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON

PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON

WITHOUT DAYTIME RUNNING LIGHT SYSTEM

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Description

INFOID:0000000006451745

The parking, license plate, tail lamps and each illumination are not turned ON in any condition.

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure

INFOID:0000000006451746

1.

COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT

CONSULT-III DATA MONITOR

1.

Select “TAIL & CLR REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Replace BCM. Refer to 

BCS-93, "Removal and Installation"

 (with Intelligent Key), 

BCS-161,

"Removal and Installation"

 (without Intelligent Key).

WITH DAYTIME RUNNING LIGHT SYSTEM

WITH DAYTIME RUNNING LIGHT SYSTEM : Description

INFOID:0000000006452140

The parking, license plate, tail lamps and each illumination are not turned ON in any condition.

WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure

INFOID:0000000006452141

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the combination switch normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT

CONSULT-III DATA MONITOR

1.

Select “TAIL & CLR REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace BCM. Refer to 

BCS-93, "Removal and Installation"

 (with Intelligent Key), 

BCS-161,

"Removal and Installation"

 (without Intelligent Key).

3.

DAYTIME RUNNING LIGHT RELAY CIRCUIT INSPECTION

Monitor item

Condition

Monitor status

TAIL & CLR REQ

Lighting switch

1ST

ON

OFF

OFF

Monitor item

Condition

Monitor status

TAIL & CLR REQ

Lighting switch

1ST

On

OFF

Off

PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON

EXL-81

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Check the daytime running light relay circuit. Refer to 

EXL-50, "Component Function Check"

.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace the malfunctioning part.