Juke F15 (2012 year). Service Repair Manual

DLK-528

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 4]

KEYFOB BATTERY

KEYFOB BATTERY

Component Function Check

INFOID:0000000006616483

CHECK FUNCTION

Check door lock and unlock operation with keyfob button.
Is the inspection result normal?

YES

>> Keyfob is OK.

>> Refer to

DLK-528, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006616484

CHECK KEYFOB BATTERY

Check by connecting a resistance (approximately 300

Ω

) so that the

current value becomes about 10 mA.

Is the measurement value within the specification?

YES

>> Replace keyfob.

>> Replace keyfob battery. Refer to

DLK-603, "Removal

and Installation"

Standard

: Approx. 2.5 - 3.0 V

OCC0607D

REMOTE KEYLESS ENTRY RECEIVER

DLK-529

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 4]

DLK

REMOTE KEYLESS ENTRY RECEIVER

Component Function Check

INFOID:0000000006616485

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “KEYLESS ” or “KEYLESS UNLOCK” in “DATA MONITOR” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Remote keyless entry receiver is OK.

>> Refer to

DLK-529, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006616486

CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT

Turn ignition switch OFF.

Disconnect BCM connector and remote keyless entry receiver connector.

Check continuity between BCM harness connector and remote keyless entry receiver harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness.

CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY

Reconnect BCM connector.

Check voltage between remote keyless entry receiver harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> GO TO 3.

CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1

Disconnect BCM connector

Check continuity between BCM harness connector and remote keyless entry receiver harness connector.

Monitor item

Condition

Status

KEYLESS LOCK

Keyfob button

LOCK

UNLOCK

Off

KEYLESS UNLOCK

LOCK

Off

UNLOCK

BCM

Remote keyless entry receiver

Continuity

Connector

Terminal

Connector

Terminal

M65

M73

Existed

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

(+)

(–)

Voltage

(Approx.)

Remote keyless entry receiver

Connector

Terminal

M73

Ground

5 V

DLK-530

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 4]

REMOTE KEYLESS ENTRY RECEIVER

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-161, "Removal and Installation"

>> Repair or replace harness.

CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL

Reconnect remote keyless entry receiver connector.

Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.

Is the inspection result normal?

YES

>> GO TO 5.

>> Replace remote keyless entry receiver.

CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2

Disconnect BCM connector and remote keyless entry receiver connector.

Check continuity between BCM harness connector and remote keyless entry receiver harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-161, "Removal and Installation"

BCM

Remote keyless entry receiver

Continuity

Connector

Terminal

Connector

Terminal

M65

M73

Existed

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

(+)

(–)

Condition

Signal

(Reference value)

Remote keyless entry receiver

Connector

Terminal

M73

Ground

Waiting

Press the Intelligent
Key lock or unlock
button

JMKIA3838GB

JMKIA3841GB

BCM

Remote keyless entry receiver

Continuity

Connector

Terminal

Connector

Terminal

M65

M73

Existed

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

DLK-532

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 4]

UNLOCK SENSOR

UNLOCK SENSOR

Component Function Check

INFOID:0000000006616495

CHECK FUNCTION

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “LOCK STATUS” in “DATA MONITOR” mode.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Unlock sensor is OK.

>> Refer to

DLK-532, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006616496

CHECK BCM OUTPUT SIGNAL

Turn ignition switch OFF.

Disconnect front door lock assembly (driver side) connector.

Check signal between front door lock assembly (driver side) harness connector and ground using oscillo-
scope.

Is the inspection result normal?

YES

>> GO TO 3.

>> GO TO 2.

CHECK UNLOCK SENSOR CIRCUIT

Disconnect BCM connector.

Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-161, "Removal and Installation"

Monitor item

Condition

Status

LOCK STATUS

Driver side door

Lock

OFF

Unlock

(+)

(–)

Signal

(Reference value)

Front door lock assembly (driver side)

Connector

Terminal

D13

Ground

PKIB4960J

BCM

Front door lock assembly (driver side)

Continuity

Connector

Terminal

Connector

Terminal

M65

D13

Existed

BCM

Ground

Continuity

Connector

Terminal

M65

Not existed

UNLOCK SENSOR

DLK-533

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 4]

DLK

>> Repair or replace harness.

CHECK UNLOCK SENSOR GROUND CIRCUIT

Check continuity between front door lock assembly (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace harness.

CHECK UNLOCK SENSOR

Refer to

DLK-533, "Component Inspection"

Is the inspection result normal?

YES

>> GO TO 5.

>> Replace front door lock assembly (driver side).

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

>> INSPECTION END

Component Inspection

INFOID:0000000006616497

CHECK UNLOCK SENSOR

Turn ignition switch OFF.

Disconnect front door lock assembly (driver side) connector.

Check continuity between front door lock assembly (driver side) terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace front lock assembly (driver side).

Front door lock assembly (driver side)

Ground

Continuity

Connector

Terminal

D13

Existed

Front door lock assembly (driver side)

Condition

Continuity

Terminal

Driver side door

Unlock

Existed

Lock

Not existed

DLK-534

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH

SYMPTOM DIAGNOSIS

DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH

ALL DOOR

ALL DOOR : Description

INFOID:0000000006619157

All doors do not lock/unlock using door lock and unlock switch.

ALL DOOR : Diagnosis Procedure

INFOID:0000000006619158

CHECK DOOR LOCK AND UNLOCK SWITCH

Check door lock and unlock switch.
Refer to

DLK-520, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK DOOR LOCK ACTUATOR

Check front door lock assembly (driver side).
Refer to

DLK-515, "DRIVER SIDE : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK DOOR SWITCH

Check door switch.
Refer to

DLK-397, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK KEY SWITCH

Check key switch. Refer to

DLK-401, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

DRIVER SIDE

DRIVER SIDE : Description

INFOID:0000000006619159

Driver side door does not lock/unlock using door lock and unlock switch.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000006619160

CHECK DOOR LOCK ACTUATOR

Check front door lock assembly (driver side).
Refer to

DLK-515, "DRIVER SIDE : Component Function Check"

DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH

DLK-535

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DLK

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

PASSENGER SIDE

PASSENGER SIDE : Description

INFOID:0000000006619161

Passenger side door does not lock/unlock using door lock and unlock switch.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000006619162

CHECK DOOR LOCK ACTUATOR

Check front door lock assembly (passenger side).
Refer to

DLK-516, "PASSENGER SIDE : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

REAR LH

REAR LH : Description

INFOID:0000000006619163

Rear LH side door does not lock/unlock using door lock and unlock switch.

REAR LH : Diagnosis Procedure

INFOID:0000000006619164

CHECK DOOR LOCK ACTUATOR

Check rear door lock assembly LH.
Refer to

DLK-517, "REAR LH : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

REAR RH

REAR RH : Description

INFOID:0000000006619165

Rear RH side door does not lock/unlock using door lock and unlock switch.

DLK-536

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH

REAR RH : Diagnosis Procedure

INFOID:0000000006619166

CHECK DOOR LOCK ACTUATOR

Check rear door lock assembly RH
Refer to

DLK-518, "REAR RH : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

DOOR DOES NOT LOCK/UNLOCK WITH DRIVER SIDE DOOR LOCK KNOB OR

DOOR KEY CYLINDER

DLK-537

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DLK

DOOR DOES NOT LOCK/UNLOCK WITH DRIVER SIDE DOOR LOCK
KNOB OR DOOR KEY CYLINDER

Diagnosis Procedure

INFOID:0000000006619156

CHECK POWER DOOR LOCK OPERATION

Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?

YES

>> GO TO 2.

>> Go to

DLK-534, "ALL DOOR : Diagnosis Procedure"

CHECK UNLOCK SENSOR

Check unlock sensor.
Refer to

DLK-532, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

DLK-538

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DOOR DOES NOT LOCK/UNLOCK WITH KEYFOB

DOOR DOES NOT LOCK/UNLOCK WITH KEYFOB

Diagnosis Procedure

INFOID:0000000006619167

CHECK POWER DOOR LOCK OPERATION

Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?

YES

>> GO TO 2.

>> Go to

DLK-534, "ALL DOOR : Diagnosis Procedure"

CHECK REMOTE KEYLESS ENTRY RECEIVER

Check remote keyless entry receiver.
Refer to

DLK-529, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK KEYFOB BATTERY

Check keyfob battery.
Refer to

DLK-528, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

BACK DOOR DOES NOT OPENED

DLK-539

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DLK

BACK DOOR DOES NOT OPENED

Diagnosis Procedure

INFOID:0000000006619155

CHECK BACK DOOR OPENER SWITCH

Check back door opener switch.
Refer to

DLK-513, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK BACK DOOR OPENER ACTUATOR

Check back door opener actuator.
Refer to

DLK-512, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK VEHICLE SPEED SIGNAL

Check vehicle speed signal.
Refer to

MWI-46, "DTC Logic"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

DLK-540

< SYMPTOM DIAGNOSIS >

[TYPE 4]

ANTI-HIJACK FUNCTION DOES NOT OPERATE

ANTI-HIJACK FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000006619153

CHECK “DOOR LOCK–UNLOCK SET” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT” mode.

Check “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT”
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 2

>> Set “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT”

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPERATE

DLK-541

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DLK

VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPER-
ATE

Diagnosis Procedure

INFOID:0000000006619180

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 2.

>> Set “Lock Only” or “Lock/Unlock” in “WORK SUPPORT”.

CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.

Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “VH SPD” in “AUTOMATIC DOOR LOCK SELECT”.

REPLACE BCM

• Replace BCM. Refer to

BCS-161, "Removal and Installation"

• Confirm the operation after replacement.
Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

DLK-542

< SYMPTOM DIAGNOSIS >

[TYPE 4]

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000006619170

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 2.

>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-

ATE

DLK-543

< SYMPTOM DIAGNOSIS >

[TYPE 4]

DLK

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE

Diagnosis Procedure

INFOID:0000000006619173

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 2.

>> Set “Unlock Only”, “Lock Only” or “Lock/Unlock” in “AUTOMATIC LOCK/UNLOCK SELECT”.

CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.

Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “P RANGE” in “AUTOMATIC DOOR LOCK SELECT”.

CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

Select “DOOR LOCK” of “BCM” using CONSULT-III.

Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

Check “AUTOMATIC DOOR UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

Is the inspection result normal?

YES

>> GO TO 4.

>> Set “MODE 2” or “MODE 4” in “AUTOMATIC DOOR UNLOCK SELECT”.

CHECK TCM

Check TCM for DTC.
Refer to

TM-171, "DTC Index"

(RE0F10B models) or

TM-366, "DTC Index"

(RE0F11A models).

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

Replace BCM. Refer to

BCS-161, "Removal and Installation"

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

Juke F15 (2012 year). Service Repair Manual - part 96