Nissan Juke (2016 year). Service Repair Manual - part 685

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     683      684      685      686     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 685

 

 

WT-26

< DTC/CIRCUIT DIAGNOSIS >

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000012201853

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION 

With CONSULT

1. Turn the ignition switch ON.

CAUTION:

Never start the engine.

2. Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-47, "Tire Air Pres-

sure"

. 

CAUTION:

If the tire pressure before adjustment is close to the standard, reduce the tire pressure, and then

with the ignition switch ON, adjust the tire pressure again so that it is within the standard.

3. Perform self-diagnosis in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1716”, “C1717”, “C1718”, or “C1719” detected?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

CHECK LOW TIRE PRESSURE WARNING LAMP

Check that after the ignition switch is turned ON, the low tire pressure warning lamp illuminates for approxi-

mately 1 second and then turns OFF.
Is the inspection result normal?

YES

>> After erase DTC, INSPECTION END.

NO

>> Leave the ignition switch ON and proceed to 

WT-26, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201854

1.

PERFORM TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration for all wheels. Refer to 

WT-20, "Description"

. 

Is tire pressure sensor ID registration completed?

YES

>> GO TO 2.

NO

>> Replace tire pressure sensor. Refer to 

WT-41, "Removal and Installation"

.

2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

1. Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-47, "Tire Air Pres-

sure"

.

2. Stop the vehicle.

3. Select “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

4. Within 15 minutes after vehicle stopped, read the values that are displayed for “AIR PRESS FL”, “AIR

PRESS FR”, “AIR PRESS RR”, and “AIR PRESS RL”.

Which tire pressures is displayed as 438.60 kPa (4.47 kg/cm

2

, 63.60 psi)?

DTC

Display Item

Malfunction detected condition

Possible causes

C1716

[PRESSDATA ERR] FL

Malfunction in the tire pressure data from the 
front LH wheel tire pressure sensor.

• Excessive tire pressure
• Tire pressure sensor ID reg-

istration incomplete

• Tire pressure sensor

C1717

[PRESSDATA ERR] FR

Malfunction in the tire pressure data from the 
front RH wheel tire pressure sensor.

C1718

[PRESSDATA ERR] RR

Malfunction in the tire pressure data from the 
rear RH wheel tire pressure sensor.

C1719

[PRESSDATA ERR] RL

Malfunction in the tire pressure data from the 
rear LH wheel tire pressure sensor.

Revision: November 2015

2016 JUKE

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

WT-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

YES

>> Replace tire pressure sensor the tire pressure as 438.60 kPa (4.47 kg/cm

2

, 63.60 psi) displayed.

Refer to 

WT-41, "Removal and Installation"

.

NO

>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to 

WT-26, "DTC

Logic"

.

Revision: November 2015

2016 JUKE

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1729 VEHICLE SPEED SIGNAL

C1729 VEHICLE SPEED SIGNAL

DTC Logic

INFOID:0000000012201855

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC CONFIRMATION PROCEDURE

With CONSULT

1. Drive the vehicle.

2. Stop the vehicle.

3. Perform self-diagnosis in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?

YES

>> Proceed to 

WT-28, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012201856

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTCs detected?

YES

>> Check the DTCs.

NO

>> GO TO 2.

2.

CHECK BCM INPUT/OUTPUT SIGNAL

Check BCM input/output signal values. Refer to 

BCS-39, "Reference Value"

. 

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions. 

NO

>> Replace the BCM. Refer to 

BCS-94, "Removal and Installation"

.

DTC

Display Item

Malfunction detected condition

Possible causes

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

• CAN communication
• BCM
• ABS actuator and electric unit (control unit) malfunction

Revision: November 2015

2016 JUKE

POWER SUPPLY AND GROUND CIRCUIT

WT-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000012201857

1.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Check BCM power supply and ground. Refer to 

BCS-87, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

Revision: November 2015

2016 JUKE

WT-30

< SYMPTOM DIAGNOSIS >

TPMS

SYMPTOM DIAGNOSIS

TPMS

Symptom Table 

INFOID:0000000012201858

LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART

Diagnosis items

Symptom

(Ignition switch 

ON)

Low tire pressure warning lamp

Cause

Action

Low tire pres-
sure warning 
lamp

The low tire pres-
sure warning lamp 
illuminates for 1 
second, then turns 
OFF.

Wake-up operation for all 
tire pressure sensors at 
wheels is completed.

No system malfunctions

The low tire pres-
sure warning lamp 
repeats blinking 
ON for 2 seconds 
and OFF for 0.2 
seconds.

Wake-up operation for all 
tire pressure sensors at 
wheels is not completed.

Perform the ID registration 
for all tire pressure sensors 
at wheels. Refer to 

WT-20, 

"Description"

.

Low tire pres-
sure warning 
lamp

The low tire pres-
sure warning lamp 
blinks once.

The front left tire pres-
sure sensor is not acti-
vated.

Perform the ID registration 
for the tire pressure sensor 
at front left wheel. Refer to 

WT-20, "Description"

.

The low tire pres-
sure warning lamp 
repeats blinking 
twice.

The front right tire pres-
sure sensor is not acti-
vated.

Perform the ID registration 
for the tire pressure sensor 
at front right wheel. Refer to 

WT-20, "Description"

.

The low tire pres-
sure warning lamp 
repeats blinking for 
3 times.

The rear right tire pres-
sure sensor is not acti-
vated.

Perform the ID registration 
for the tire pressure sensor 
at rear right wheel. Refer to 

WT-20, "Description"

.

The low tire pres-
sure warning lamp 
repeats blinking for 
4 times.

The rear left tire pressure 
sensor is not activated.

Perform the ID registration 
for the tire pressure sensor 
at rear left wheel. Refer to 

WT-20, "Description"

.

SEIA0592E

SEIA0593E

JPEIC0090GB

SEIA0595E

SEIA0596E

SEIA0597E

Revision: November 2015

2016 JUKE

TPMS

WT-31

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

NOTE:

If tire pressure sensor wake-up operation is not completed for two or more tire pressure sensors, the applica-

ble low tire pressure warning lamp blinking patterns are displayed continuously.

(Example: Blinks once/OFF/blinks 3 times = Wake-up operation is not completed at the front left wheel and

rear right wheel tire pressure sensors.)

Low tire pres-
sure warning 
lamp

The low tire pres-
sure warning lamp 
turns ON and stays 
illuminated.

Low tire pressure

Check the tire pressure for 
all wheels and adjust to the 
specified value. Refer to 

WT-47, "Tire Air Pressure"

. 

The low tire pres-
sure warning lamp 
repeats blinking at 
0.5-second inter-
vals for 1 minute, 
and then stays illu-
minated.

The combination meter 
fuse is open or removed 
(or pulled out).

Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.

The BCM harness con-
nector is removed.

Check the connection con-
ditions of the BCM harness 
connector, and repair if nec-
essary.

Tire Pressure Monitoring 
System (TPMS) mal-
function.

• Perform CONSULT self-

diagnosis. Refer to 

WT-

10, "AIR PRESSURE 
MONITOR : CONSULT 
Function (BCM - AIR 
PRESSURE MONI-
TOR)"

.

• If necessary, perform tire 

pressure sensor ID regis-
tration. Refer to 

WT-20, 

"Description"

.

Diagnosis items

Symptom

(Ignition switch 

ON)

Low tire pressure warning lamp

Cause

Action

SEIA0598E

SEIA0788E

Revision: November 2015

2016 JUKE

WT-32

< SYMPTOM DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON

Description

INFOID:0000000012201859

The low tire pressure warning lamp does not illuminate when the ignition switch is turned ON.

NOTE:

The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-

tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring

system.

The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire

pressure warning lamp does not illuminate when the ignition switch is turned ON.

Diagnosis Procedure

INFOID:0000000012201860

1.

CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL

With CONSULT

1. Turn the ignition switch ON.

CAUTION:

Never start the engine.

2. Select “ACTIVE TEST” in “AIR PRESSURE MONITOR” of “BCM”.

3. Touch “WARNING LAMP” to turn ON the low tire pressure warning lamp.
When “ACTIVE TEST” is performed, does the low tire pressure warning lamp in the combination meter turn

ON?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK LOW TIRE PRESSURE WARNING LAMP OPERATION

Check that the low tire pressure warning lamp is turned OFF after turns ON for approximately 1 second, when

the ignition switch is turned ON.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace the BCM. Refer to 

BCS-94, "Removal and Installation"

.

3.

CHECK COMBINATION METER POWER SUPPLY CIRCUIT

Perform the trouble diagnosis for combination meter power supply circuit. Refer to 

MWI-53, "COMBINATION

METER : Diagnosis Procedure"

.

Is the inspection result normal?

YES-1 >> INSPECTION END

NO

>> Repair or replace error-detected parts.

Revision: November 2015

2016 JUKE

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF

WT-33

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF

Description

INFOID:0000000012201861

The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.

Diagnosis Procedure

INFOID:0000000012201862

1.

CHECK TIRE PRESSURE

1. Turn the ignition switch ON.

CAUTION:

Never start the engine.

2. Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-47, "Tire Air Pres-

sure"

. 

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels.

2.

CHECK LOW TIRE PRESSURE WARNING LAMP

Check low tire pressure warning lamp display.
Does not low tire pressure warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

CHECK BCM

With CONSULT

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

BCS-62, "DTC Index"

.

NO

>> GO TO 4.

4.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for power supply and ground circuit. Refer to 

BCS-87, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

. 

NO

>> Repair or replace error-detected parts.

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     683      684      685      686     ..