Nissan Juke (2016 year). Service Repair Manual - part 74

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     72      73      74      75     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 74

 

 

CORROSION PROTECTION

BRM-27

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

BRM

N

O

P

: Vehicle front

: Sealed portions

JSKIA2135ZZ

Revision: November 2015

2016 JUKE

BRM-28

< REMOVAL AND INSTALLATION >

CORROSION PROTECTION

Body Sealing (AWD Models)

INFOID:0000000012199835

The following figure shows the areas that are sealed at the factory. Sealant that is applied to these areas

should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of sealant

and not to allow other unaffected parts to come into contact with the sealant.

Standard roof models

With sunroof models

: Vehicle front

: Sealed portions

JSKIA2199ZZ

Revision: November 2015

2016 JUKE

CORROSION PROTECTION

BRM-29

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

BRM

N

O

P

: Vehicle front

: Sealed portions

JSKIA5309ZZ

Revision: November 2015

2016 JUKE

BRM-30

< REMOVAL AND INSTALLATION >

CORROSION PROTECTION

: Vehicle front

: Sealed portions

JSKIA2202ZZ

Revision: November 2015

2016 JUKE

BODY CONSTRUCTION

BRM-31

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

BRM

N

O

P

BODY CONSTRUCTION

Body Construction (Standard roof Models)

INFOID:0000000012199836

1.

Outer side body

2.

Outer front pillar reinforcement

3.

Upper inner front pillar

4.

Lower dash

5.

Hoodledge reinforcement

6.

Lower front pillar hinge brace

7.

Weld nut

8.

Side dash

9.

Inner front pillar reinforcement

JSKIA2203ZZ

Revision: November 2015

2016 JUKE

BRM-32

< REMOVAL AND INSTALLATION >

BODY CONSTRUCTION

10. Upper hinge plate

11. Lower hinge plate

12. Lower front pillar bulkhead

13. Inner front pillar reinforcement

14. Front floor reinforcement

15. Front floor

16. Front outrigger

17. Inner sill

18. Outer sill reinforcement

19. Inner center pillar reinforcement

20. Inner center pillar

21. Center pillar reinforcement

22. Center pillar hinge brace

23. Inner sill reinforcement

24. Center sill reinforcement

25. Inner sill extension

26. Inner rear wheelhouse

27. Outer rear wheelhouse

28. Rear roof rail brace

29. Inner rear pillar reinforcement

30. Rear fender extension

31. Inner rear pillar

32. Inner rear wheelhouse reinforce-

ment

Revision: November 2015

2016 JUKE

BODY CONSTRUCTION

BRM-33

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

BRM

N

O

P

Body Construction (With sunroof Models)

INFOID:0000000012199837

1.

Outer side body

2.

Outer front pillar reinforcement

3.

Upper inner front pillar

4.

Lower dash

5.

Hoodledge reinforcement

6.

Lower front pillar hinge brace

7.

Weld nut

8.

Side dash

9.

Inner front pillar reinforcement

10. Upper hinge plate

11. Lower hinge plate

12. Lower front pillar bulkhead

13. Inner front pillar reinforcement

14. Front floor reinforcement

15. Front floor

JSKIA2204ZZ

Revision: November 2015

2016 JUKE

BRM-34

< REMOVAL AND INSTALLATION >

BODY CONSTRUCTION

Rear Fender Hemming Process

INFOID:0000000012199838

1. A wheel arch is to be installed and hemmed over the left and right outer wheel houses.

2. In order to hem the wheel arch, it is necessary to repair any damaged or defaced parts around outer

wheel house.

CAUTION:

Ensure that the area that is to be glued around the outer wheelhouse is undamaged or defaced.

PROCEDURE OF THE HEMMING PROCESS

• Peel off old bonding material on the surface of the outer wheel-

house and clean thoroughly.

• Peel off a primer coat in the specified area where new adhesive is

to be applied on rear fender (the replacing part).

• Apply new adhesive to both specified areas of the outer wheel-

house and rear fender.

• Attach rear fender to the body of the car, and weld the required

part except the hemming part.

• Bend the welded part starting from the center of the wheel arch

gradually with a hammer and a dolly. (Also hem the end of the

flange.)

• Hemming with a hammer is conducted to an approximate angle of

80 degrees.

• Starting from the center, hem the wheel arch gradually, using slight

back and forth motion with a hemming tool.

16. Front outrigger

17. Inner sill

18. Outer sill reinforcement

19. Nut plate

20. Inner center pillar

21. Center pillar reinforcement

22. Center pillar hinge brace

23. Inner sill reinforcement

24. Center sill reinforcement

25. Inner sill extension

26. Inner rear wheelhouse

27. Outer rear wheelhouse

28. Rear roof rail brace

29. Inner rear pillar reinforcement

30. Rear fender extension

31. Inner rear pillar

32. Inner rear wheelhouse reinforce-

ment

<Adhesive> 3M™ Automix™ Panel Bonding Adhe-

sive 08115 or equivalent

JSKIA0136GB

SIIA2245E

SIIA2246E

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     72      73      74      75     ..