Nissan Juke F15. Manual - part 290

CENTER STEM ASSEMBLY

DLN-165

< UNIT DISASSEMBLY AND ASSEMBLY >

[REAR FINAL DRIVE: RTVS]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

Tooth Contact Judgment Guide

5. If tooth contact is improperly adjusted, follow the procedure

below to adjust the pinion height (dimension X). For selecting

adjusting shim, refer to the latest parts information.

• If the tooth contact is near the face (face contact), or near the

heel (heel contact), thicken drive pinion gear adjusting shim to

move drive pinion closer to drive gear.

SDIA2549E

SDIA0517E

PDIA0440E

DLN-166

< UNIT DISASSEMBLY AND ASSEMBLY >

[REAR FINAL DRIVE: RTVS]

CENTER STEM ASSEMBLY

• If the tooth contact is near the flank (flank contact), or near the

toe (toe contact), thin drive pinion gear adjusting shim to move

drive pinion farther from drive gear.

BACKLASH

1. Remove rear cover. Refer to 

DLN-159, "Disassembly"

.

2. Following the procedure below, install the dummy cover set [SST: KV381096S0 (

—

)] to gear car-

rier.

a. Temporarily install the bearing guides [SST: KV38109610 (

—

), KV38109620 (

—

)]  to

gear carrier.

b. Position the dummy cap spacers [SST: KV38109630 (

—

), KV38109640 (

—

)] and the

angle [SST: KV38109650 (

—

)] to bearing guide.

c.

Use rear cover mounting bolts, and tighten bolts to the specified torque. Refer to 

DLN-158, "Exploded

View"

.

d. Tighten dummy cap spacer mounting bolts evenly to the specified torque.

3. Fit a dial indicator to the drive gear face to measure the back-

lash.

• If the backlash is outside of the specified value, change the

thickness of side bearing adjusting shims.

Inspection

INFOID:0000000012199520

INSPECTION AFTER DISASSEMBLY

Drive Gear and Drive Pinion

• Clean up the disassembled parts.

• If the gear teeth never mesh or line-up correctly, determine the cause and adjust or replace as necessary.

• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new drive

gear and drive pinion as a set.

Bearing

• Whenever disassembled, replace.

• Clean up the disassembled parts.

• If any chipped (by friction), pitted, worn, rusted or scratched marks, or unusual noise from the bearing is

observed, replace as a bearing assembly (as a new set).

PDIA0441E

Tightening torque

: 5.9 N·m (0.6 kg-m, 52 in-lb)

Backlash

: Refer to 

DLN-175, "Back-

lash"

.

When the backlash is large:

Make drive gear back adjusting shims thicker, and drive 
gear front adjusting shims thinner. For selecting ad-
justing shim, refer to the latest parts information.

When the backlash is small:

Make drive gear back adjusting shims thinner, and 
drive gear front adjusting shims thicker. For selecting 
adjusting shim, refer to the latest parts information.

JSDIA2256ZZ

CENTER STEM ASSEMBLY

DLN-167

< UNIT DISASSEMBLY AND ASSEMBLY >

[REAR FINAL DRIVE: RTVS]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

Oil Seal

• Whenever disassembled, replace.

• If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace them.

Gear Carrier and Rear Cover

• Check damage and cracks of gear carrier and rear cover.

DLN-168

< UNIT DISASSEMBLY AND ASSEMBLY >

[REAR FINAL DRIVE: RTVS]

DRIVE PINION

DRIVE PINION

Exploded View

INFOID:0000000012199521

1.

Filler plug

2.

Gasket

3.

Drain plug

4.

Breather tube

5.

Hose clamp

6.

Breather hose

7.

Breather

8.

Band clip

9.

Sub-harness

10. Rear cover

11. Center stem

12. Side bearing (right)

13. Side bearing adjusting shim (right)

14. Side oil seal (right)

15. Connector clip

16. Electric controlled coupling (right)

17. Electric controlled coupling oil seal

18. Reamer bolt

19. Drive pinion

20. Drive pinion adjusting shim

21. Pinion bearing (rear)

22. Collapsible spacer

23. Breather

24. Gear carrier

25. Carrier bracket (right)

26. Pinion bearing (front)

27. Front oil seal

28. Companion flange

29. Drive pinion lock nut

30. Carrier bracket (left)

31. Drive gear

32. Side bearing (left)

33. Side bearing adjusting shim (left)

34. Side oil seal (left)

35. Electric controlled coupling (left)

A.

Oil seal lip

B.

Gear carrier mounting face

: Always replace after every disassembly.

: Select with proper thickness.

: N·m (kg-m, ft-lb)

: Apply multi purpose grease

: Apply gear oil.

JSDIA2246GB